The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
Configuring Mobility Controller
1.
wireless mobility controller
2.
wireless mobility controller peer-group
SPG1
3.
wireless mobility controller peer-group
SPG1
member
ip
member-ip-addr
public-ip
public-ip-addr
4.
wireless mobility controller peer-group
SPG1
member
ip
member-ip-addr
public-ip
public-ip-addr
5.
wireless mobility controller peer-group
SPG2
6.
wireless mobility controller peer-group
SPG2
member
ip
member-ip-addr
public-ip
public-ip-addr
7.
wireless mobility controller peer-group
SPG1
bridge-domain-id
id
This example shows how to create peer group and add members to it:
Controller(config)# wireless mobility controller Controller(config)# wireless mobility controller peer-group SPG1 Controller(config)# wireless mobility controller peer-group SPG1 Controller(config)# wireless mobility controller peer-group SPG1 member ip 10.10.20.2 public-ip 10.10.20.2 Controller(config)# wireless mobility controller peer-group SPG1 member ip 10.10.20.6 public-ip 10.10.20.6 Controller(config)# wireless mobility controller peer-group SPG2 Controller(config)# wireless mobility controller peer-group SPG2 member ip 10.10.10.20 public-ip 10.10.10.20 Controller(config)# wireless mobility controller peer-group SPG1 bridge-domain-id 54
Configuration for wireless mobility groups and mobility group members where the mobility group is a group of MCs.
MCs can belong only to one mobility group, and can know MCs in several mobility groups.
1.
wireless mobility group name
group-name
2.
wireless mobility group member ip
member-ip-addr
public-ip
public-ip-addr
3.
wireless mobility group keepalive interval
time-in-seconds
4.
wireless mobility group keepalive count
count
Command or Action | Purpose | |||
---|---|---|---|---|
Step 1 | wireless mobility group name
group-name
Example: Controller(config)# wireless mobility group name Mygroup
|
Creates a mobility group named Mygroup. | ||
Step 2 | wireless mobility group member ip
member-ip-addr
public-ip
public-ip-addr
Example: Controller(config)# wireless mobility group member ip 10.10.34.10 public-ip 10.10.34.28
|
Adds a mobility controller to the Mygroup mobility group.
| ||
Step 3 | wireless mobility group keepalive interval
time-in-seconds
Example: Controller(config)# wireless mobility group keepalive interval 5
|
Configures the interval between two keepalives sent to a mobility member. | ||
Step 4 | wireless mobility group keepalive count
count
Example: Controller(config)# wireless mobility group keepalive count 3
|
Configures the keep alive retries before a member status is termed DOWN. |
Controller(config)# wireless mobility group name Mygroup Controller(config)# wireless mobility group member ip 10.10.34.10 public-ip 10.10.34.28 Controller(config)# wireless mobility group keepalive interval 5 Controller(config)# wireless mobility group keepalive count 3
Mobility controllers can belong to only one mobility group and can know mobility controllers in several mobility groups.
MCs belong to only one group, and can know MCs in several groups.
1.
wireless mobility group member ip
member-ip-addr
public-ip
public-ip-addr
group
group-name
Command or Action | Purpose |
---|
Mobility controllers belong to only one group, and can know several mobility groups.
Use this configuration to disable the sticky anchor. This command can also be used, if required, between all MA's and MC's where roaming is expected for the target SSID.
1.
wlan open21
2.
no mobility anchor sticky
Command or Action | Purpose |
---|
Controller(config)# wlan open20 Controller(config-wlan)# no mobility anchor sticky
You can configure a mobility oracle on a known mobility controller.
1.
wireless mobility group
member ip
member-ip-addr
group
group-name
2.
wireless mobility oracle
ip
oracle-ip-addr
Command or Action | Purpose | |
---|---|---|
Step 1 |
wireless mobility group
member ip
member-ip-addr
group
group-name
Example: Controller(config)# wireless mobility group member ip 10.10.10.10 group Group3
|
Creates and adds a MC to a mobility group. |
Step 2 |
wireless mobility oracle
ip
oracle-ip-addr
Example: Controller(config)# wireless mobility oracle ip 10.10.10.10
|
Configures the mobility controller as mobility oracle. |
Controller(config)# wireless mobility group member ip 10.10.10.10 group Group3 Controller(config)# wireless mobility oracle ip 10.10.10.10
You can configure a mobility oracle on a known mobility controller.
A guest controller is used when the client traffic is tunneled to a guest anchor controller in the demilitarized zone (DMZ). The guest client goes through a web authentication process. The web authentication process is optional, and the guest is allowed to pass traffic without authentication too.
Enable the WLAN on the mobility agent on which the guest client connects with the mobility anchor address of the guest controller.
Note | With Cisco 5700 Series WLC as the guest anchor controller and Cisco 5500 Series WLC or Cisco WiSM2 as export foreign controller, the guest user role per user is not supported on the Cisco 5700 Series WLC. |
1.
wlan
wlan-id
2.
mobility anchor
guest-anchor-ip-addr
3.
client vlan
vlan-name
4.
security open
Command or Action | Purpose | |||
---|---|---|---|---|
Step 1 | wlan
wlan-id
Example: Controller(config)# wlan Mywlan1
|
Creates a WLAN for the client. | ||
Step 2 | mobility anchor
guest-anchor-ip-addr
Example: Controller(config-wlan)# mobility anchor 10.10.10.2
|
| ||
Step 3 | client vlan
vlan-name
Example: Controller(config-wlan)# client vlan gc_ga_vlan1
|
Assigns a VLAN to the client's WLAN. | ||
Step 4 | security open
Example: Controller(config-wlan)# security open
|
Assigns a security type to the WLAN. |
Controller(config)# wlan Mywlan1 Controller(config-wlan)# mobility anchor 10.10.10.2 Controller(config-wlan)# client vlan gc_ga_vlan1 Controller(config-wlan)# security open
1.
wlan Mywlan1
2.
mobility anchor <guest-anchors-own-ip-address>
3.
client vlan<vlan-name>
4.
security open
Command or Action | Purpose | |
---|---|---|
Step 1 | wlan Mywlan1 Example: Controller(config)# wlan Mywlan1
|
Creates a wlan for the client. |
Step 2 | mobility anchor <guest-anchors-own-ip-address> Example: Controller(config-wlan)# mobility anchor 10.10.10.2
|
Enables the guest anchors IP address on the guest anchor (GA). The GA assigns its own address on itself. |
Step 3 | client vlan<vlan-name> Example: Controller(config-wlan)# client vlan gc_ga_vlan1
|
Assigns a vlan to the clients wlan. |
Step 4 | security open Example: Controller(config-wlan)# security open
|
Assigns a security type to the wlan. |
Controller(config)# wlan Mywlan1 Controller(config-wlan)# mobility anchor 10.10.10.2 Controller(config-wlan)# client vlan gc_ga_vlan1 Controller(config-wlan)# security open