- Command Line Interface Reference, Modes G - H, StarOS Release 21.6
- Gateway Selection Profile Configuration Mode Commands
- GGSN Service Configuration Mode Commands
- Global Configuration Mode Commands (A-K)
- Global Configuration Mode Commands (L-S)
- Global Configuration Mode Commands (T-threshold phspc)
- Global Configuration Mode Commands (threshold poll commands A - N)
- Global Configuration Mode Commands (threshold poll commands O - Z)
- Global Configuration Mode Commands (threshold ppp - wsg-lookup)
- Global Title Translation Address-Map Configuration Mode Commands
- Global Title Translation Association Configuration Mode Commands
- GPRS Service Configuration Mode Commands
- GRE Tunnel Interface Configuration Mode Commands
- Gs Service Configuration Mode Commands
- GT-Format1 Configuration Mode Commands
- GT-Format2 Configuration Mode Commands
- GT-Format3 Configuration Mode Commands
- GT-Format4 Configuration Mode Commands
- GTPC Load Control Profile Configuration Mode Commands
- GTPC Overload Control Profile Configuration Mode Commands
- GTPP Server Group Configuration Mode Commands
- GTP-U Service Configuration Mode Commands
- HA Proxy DNS Configuration Mode Commands
- HA Service Configuration Mode Commands
- HD RAID Configuration Mode Commands
- HD RAID Disk Configuration Mode Commands
- HD Storage Policy Configuration Mode Commands
- HeNB-GW Access Service Configuration Mode Commands
- HeNBGW Qci Dscp Mapping Table Configuration Mode Commands
- HeNB-GW Network Service Configuration Mode Commands
- Hexdump Module Configuration Mode Commands
- HLR Configuration Mode Commands
- HNB-GW Global Configuration Mode Commands
- HNB-GW Service Configuration Mode Commands
- HNB-CS Network Configuration Mode Commands
- HNB-PS Network Configuration Mode Commands
- HNB-RN PLMN Configuration Mode Commands
- HSGW Service Configuration Mode Commands
- HSGW Service RoHC Configuration Mode Commands
- HSS Peer Service Configuration Mode Commands
Command Line Interface Reference, Modes G - H, StarOS Release 21.6
Bias-Free Language
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
- Updated:
- February 16, 2018
Chapter: HeNB-GW Access Service Configuration Mode Commands
HeNB-GW Access
Service Configuration Mode Commands
In Release 20, 21.0 and 21.1, HeNBGW is not supported. Commands in this configuration mode must not be used in these releases. For more information, contact your Cisco account representative.
A new service "henbgw-access-service" is defined under Context Configuration Mode to initialize HeNB-GW functionality. This service configuration controls the S1-MME interface for communication between HeNB-GW to HeNB(s). HeNBs connect to the S1-MME bind address configured in this service.
Mode
Exec > Global Configuration > Context Configuration > HeNBGW-Access Service Configuration
configure > context context_name > henbgw-access-service service_name
Entering the above command sequence results in the following prompt:
[context_name]host_name(config-henbgw-access-service)#
The commands or keywords/variables that are available are dependent on platform type, product version, and installed license(s).
- associate henbgw-network-service
- associate sctp-param-template
- associate x2gw-service
- bind s1-mme
- csg-optimized-paging
- end
- exit
- mme-id
- nas-node-selection
- plmn
- s1-mme ip qos-dscp
- s1-mme sctp port
- s1u-relay
- security-gateway bind
- security-gateway ip
- timeout
associate henbgw-network-service
Associates a previously configured HeNB-GW Network service to this HeNB-GW Access service. An HeNB-GW Network service must be configured in Context Configuration mode before using this configuration.
Product
HeNB-GW
Privilege
Security Administrator, Administrator
Mode
Exec > Global Configuration > Context Configuration > HeNBGW-Access Service Configuration
configure > context context_name > henbgw-access-service service_name
Entering the above command sequence results in the following prompt:
[context_name]host_name(config-henbgw-access-service)#
Syntax
Syntax Description
associate henbgw-network-service svc_name [ context contxt_name ] no associate henbgw-network-service
no
Removes the associated HeNB-GW Network service from this HeNB-GW Access service configuration.
svc_name
Identifies the name of the pre-configured HeNB-GW Network service to associate with this HeNB-GW Access service.
svc_name is an alphanumeric string of 1 through 63 characters.
context contxt_name
Identifies the name of the context to which the HeNBGW service belongs.
contxt_name is an alphanumeric string of 1 through 79 characters.
Usage Guidelines
Use this command to bind/associate a pre-configured HeNB-GW Network service to the this HeNB-GW Access service. The HeNB-GW Network service can be configured in Context configuration mode. The associate configuration is used to establish associations with other helper services in general.
Example
associate henbgw-network-service henb-network
associate sctp-param-template
Associates a previously configured SCTP Parameter Template to this HeNB-GW Access service. An SCTP Parameter Template must be configured globally before using this configuration.
Product
HeNB-GW
Privilege
Security Administrator, Administrator
Mode
Exec > Global Configuration > Context Configuration > HeNBGW-Access Service Configuration
configure > context context_name > henbgw-access-service service_name
Entering the above command sequence results in the following prompt:
[context_name]host_name(config-henbgw-access-service)#
Syntax
Syntax Description
associate sctp-param-template template_name no associate sctp-param-template
no
Removes the associated SCTP Parameter Template from this HeNB-GW Access service configuration.
template_name
Identifies the name of the pre-configured SCTP Parameter Template to associate with this HeNB-GW Access service.
template_name is an alphanumeric string of 1 through 63 characters.
Usage Guidelines
Use this command to bind/associate a pre-configured SCTP Parameter Template to the this HeNB-GW Access service. The SCTP Parameter Template can be configured global mode. The associate configuration is used to establish associations with other helper services in general.
Example
associate sctp-param-template sctp_tmpl
associate x2gw-service
This command Configures x2gw-service for this HENBGW ACCESS service.
Product
HeNB-GW
Privilege
Security Administrator, Administrator
Mode
Exec > Global Configuration > Context Configuration > HeNBGW-Access Service Configuration
configure > context context_name > henbgw-access-service service_name
Entering the above command sequence results in the following prompt:
[context_name]host_name(config-henbgw-access-service)#
Syntax
Syntax Description
associate x2gw-service associate_x2gw-service_name context context_name no associate x2gw-service
no
Removes the association of x2gw-service interface from this HeNB-GW Access service configuration.
associate_x2gw-service_name
Name of the service that will be used by this HENBGW ACCESS service to associate with. Name of the string is an alphanumeric, 1 through 63 characters.
context_name
Name of the context that will be used by this HENBGW ACCESS service to associate with. Name of the string is an alphanumeric, 1 through 79 characters.
Usage Guidelines
Use this command to associate x2gw-service with HeNBGW Access service.
Example
Following command associates an x2gw-service with specific HeNB-GW Access service with name gate123:
associate x2gw-service gate123 context ctx1
bind s1-mme
Binds the pre configured HeNB-GW Access Service to the IP address of the S1-MME interface.
Product
HeNB-GW
Privilege
Security Administrator, Administrator
Mode
Exec > Global Configuration > Context Configuration > HeNBGW-Access Service Configuration
configure > context context_name > henbgw-access-service service_name
Entering the above command sequence results in the following prompt:
[context_name]host_name(config-henbgw-access-service)#
Syntax
Syntax Description
bind s1-mme { ipv4-address ipv4_addr [ ipv6-address ipv6_addr ] | ipv6-address ipv6_addr [ ipv4-address ipv4_addr ] } max-subscribers max_sub no bind s1-mme
no
Removes the binding of S1-MME interface from this HeNB-GW Access service configuration.
ipv4-address | ipv6-address
Identifies the IPv4 and/or IPv6 address of the S1-MME interface to associate with this HeNB-GW Access service.
ipv4_addr must be an IPv4 ( dotted decimal notation) address.
ipv6_addr must be an IPv6 (colon-separated) address.
max-subscribers max_sub
Configures the maximum number of subscribers HENBGW ACCESS service can support.
max_sub is an integer ranging from 0 through 4000000.
Usage Guidelines
Use this command to bind the pre configured IPv4 address of the S1-MME interface to the HeNB-GW Access Service.
Example
bind s1-mme ipv4-address 192.68.111.61 max-subscribers 20
csg-optimized-paging
Configures the support for Paging Optimization Function on this HeNB-GW Access service based on the CSG-ID in the Paging message
Product
HeNB-GW
Privilege
Security Administrator, Administrator
Mode
Exec > Global Configuration > Context Configuration > HeNBGW-Access Service Configuration
configure > context context_name > henbgw-access-service service_name
Entering the above command sequence results in the following prompt:
[context_name]host_name(config-henbgw-access-service)#
Syntax
Syntax Description
[ no ] csg-optimized-paging
no
Removes the paging optimization function from this HeNB-GW Access service configuration.
Usage Guidelines
Use this command to enable the CSG-ID based paging optimization function to the HeNB-GW Access Service.
Example
csg-optimized-paging
end
Exits the current configuration mode and returns to the Exec mode.
Product
All
Privilege
Security Administrator, Administrator
Syntax
Syntax Description
end
Usage Guidelines
Use this command to return to the Exec mode.
exit
Exits the current mode and returns to the parent configuration mode.
Product
All
Privilege
Security Administrator, Administrator
Syntax
Syntax Description
exit
Usage Guidelines
Use this command to return to the parent configuration mode.
mme-id
Configures the MME ID for this HeNB-GW Access service. For this configuration, MME Group ID and MME Code has to be configured.
Product
HeNB-GW
Privilege
Security Administrator, Administrator
Mode
Exec > Global Configuration > Context Configuration > HeNBGW-Access Service Configuration
configure > context context_name > henbgw-access-service service_name
Entering the above command sequence results in the following prompt:
[context_name]host_name(config-henbgw-access-service)#
Syntax
Syntax Description
mme-id group-id mme_group_id mme-code mme_code no mme-id
no
Removes the configured MME ID from this HeNB-GW Access service configuration.
mme_group_id
Identifies the MME Group ID which must be entered as an integer between 32768 and 65535.
mme_code
Identifies the MME code which is again an integer value between 0 and 255.
Usage Guidelines
Use this command to configure the MME Identifier which includes the MME Group ID and MME Code for this HeNB-GW Access service. MME ID configuration is required, because it is the same ID which HeNB-GW sends in response messages to HeNBs.
 Caution | Changing the MME ID is a disruptive operation. HeNB-GW service is restarted on any change. |
Example
mme-id group-id 32770 mme-code 105
nas-node-selection
This command configures the selection of logical eNodeB/ MME based on TAI or Global eNodeB id.
Product
HeNB-GW
Privilege
Security Administrator, Administrator
Mode
Exec > Global Configuration > Context Configuration > HeNBGW-Access Service Configuration
configure > context context_name > henbgw-access-service service_name
Entering the above command sequence results in the following prompt:
[context_name]host_name(config-henbgw-access-service)#
Syntax
Syntax Description
nas-node-selection { global-eNodeB-id-based | tai-based }
This command is functional for 8 logical eNodeBs only.
global-eNodeB-id-based
Specifies the Global eNodeB id Based selection.
tai-based
Specifies the TAI based selection.This is the default option.
Usage Guidelines
Use this command to configure the selection of logical eNodeB/ MME based on TAI or Global eNodeB id.
Example
nas-node-selection global-eNodeB-id-based
plmn
Configures the PLMN identifier for this HeNB-GW Access service. Other identifiers that are configured along with the PLMN include the MCC and MNC values too.
Product
HeNB-GW
Privilege
Security Administrator, Administrator
Mode
Exec > Global Configuration > Context Configuration > HeNBGW-Access Service Configuration
configure > context context_name > henbgw-access-service service_name
Entering the above command sequence results in the following prompt:
[context_name]host_name(config-henbgw-access-service)#
Syntax
Syntax Description
[ no ] plmn id mcc mcc_val mnc mnc_val
no
Removes the existing PLMN configuration from this HeNB-GW Access service configuration.
mcc_val
Identifies the mobile country code for the IMSI which must be entered between 100 and 999 as a string of size 3.
mnc_val
Identifies the Mobile Network Code which is a value between 00 and 999, as a string of size 2 to 3.
Usage Guidelines
Use this command to configure the PLMN related configuration for this HeNB-GW Access service.
Example
plmn id mcc 123 mnc 456
s1-mme ip qos-dscp
This command configures the quality of service (QoS) differentiated service code point (DSCP) marking for IP packets sent out on the S1-MME interface, from the HeNB-GW to the HeNB(s).
Product
HeNB-GW
Privilege
Security Administrator, Administrator
Mode
Exec > Global Configuration > Context Configuration > HeNBGW-Access Service Configuration
configure > context context_name > henbgw-access-service service_name
Entering the above command sequence results in the following prompt:
[context_name]host_name(config-henbgw-access-service)#
Syntax
Syntax Description
s1-mme ip qos-dscp { af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | be | cs0 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef } default s1-mme ip qos-dscp
qos-dscp { af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | be | cs0 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef }
Default: af11
Specifies the DSCP for the specified QoS traffic pattern. qos-dscp can be configured to any one of the following:
af11: Assured Forwarding 11 per-hop-behavior (PHB)
af12: Assured Forwarding 12 PHB
af13: Assured Forwarding 13 PHB
af21: Assured Forwarding 21 PHB
af22: Assured Forwarding 22 PHB
af23: Assured Forwarding 23 PHB
af31: Assured Forwarding 31 PHB
af32: Assured Forwarding 32 PHB
af33: Assured Forwarding 33 PHB
af41: Assured Forwarding 41 PHB
af42: Assured Forwarding 42 PHB
af43: Assured Forwarding 43 PHB
be: Best effort forwarding PHB
cs0: Designates use of Class Selector 0 PHB.This is same as DSCP Value BE
cs1: Designates use of Class Selector 1 PHB
cs2: Designates use of Class Selector 2 PHB
cs3: Designates use of Class Selector 3 PHB
cs4: Designates use of Class Selector 4 PHB
cs5: Designates use of Class Selector 5 PHB
cs6: Designates use of Class Selector 6 PHB
cs7: Designates use of Class Selector 7 PHB
ef: Expedited forwarding PHB
default
Specifies the default DSCP for the specified QoS traffic pattern. The default value of DSCP is af11.
Usage Guidelines
DSCP levels can be assigned to specific traffic patterns to ensure that data packets are delivered according to the precedence with which they are tagged. The diffserv markings are applied to the IP header of every subscriber data packet transmitted over the S1-MME interface(s).
Example
s1-mme ip qos-dscp af12
s1-mme sctp port
This command configures the local Stream Control Transmission Protocol (SCTP) port used for binding the SCTP socket to communicate with the HeNBs over S1-MME interface.
Product
HeNB-GW
Privilege
Security Administrator, Administrator
Mode
Exec > Global Configuration > Context Configuration > HeNBGW-Access Service Configuration
configure > context context_name > henbgw-access-service service_name
Entering the above command sequence results in the following prompt:
[context_name]host_name(config-henbgw-access-service)#
Syntax
Syntax Description
s1-mme sctp port port_num default s1-mme sctp port
default
Sets the SCTP port to the default value of 36412 to communicate with the HeNBs using S1-MME interface.
port_num
Specifies the SCTP port number to communicate with the HeNBs using S1-MME interface as an integer from 1 through 65535. Default: 36412
Usage Guidelines
Use this command to assign the SCTP port with SCTP socket to communicate with the HeNB using S1AP.
Only one SCTP port can be associated with one MME service.
Example
default s1-mme sctp port
s1u-relay
This command configures the S1-U Relay service for the HeNB-GW Access service. The user enters in the S1-U Relay configuration mode using this command.
Product
HeNB-GW
Privilege
Security Administrator, Administrator
Mode
Exec > Global Configuration > Context Configuration > HeNBGW-Access Service Configuration
configure > context context_name > henbgw-access-service service_name
Entering the above command sequence results in the following prompt:
[context_name]host_name(config-henbgw-access-service)#
Syntax
Syntax Description
[ no ] s1u-relay
no
Removes the S1-U Relay service function from this HeNB-GW Access service configuration.
Usage Guidelines
Use this command to enable the S1-U Relay service function to the HeNB-GW Access Service. S1-U relay service is disabled by default.
Example
s1u-relay
security-gateway bind
This command configuration defines the IPv4 or IPv6 address to be used as the connection point for establishing IKEv2 sessions, and to specify the crypto template for the security gateway (SecGW) for the HeNB-GW Access service.
Product
HeNB-GW
Privilege
Security Administrator, Administrator
Mode
Exec > Global Configuration > Context Configuration > HeNBGW-Access Service Configuration
configure > context context_name > henbgw-access-service service_name
Entering the above command sequence results in the following prompt:
[context_name]host_name(config-henbgw-access-service)#
Syntax
Syntax Description
security-gateway bind { ipv4-address | ipv6-address } ip_addr crypto-template template_name [ context ctxt_name ] no security-gateway bind
no
Removes the security gateway related configuration associated with this HeNB-GW Access service configuration.
ip_addr
Identifies the security gateway address used for this HeNB-GW Access service.
For ipv4-address , ip_addr must be an IPv4 address in dotted decimal notation.
For ipv6-address , ip_addr must be an IPv6 address in colon-separated hexa-decimal notation.
template_name
Identifies the crypto template name for security gateway for this HeNB-GW Access service. It must be entered a string of size 0 to 127.
ctxt_name
Identifies the context name where crypto template is defined for this HeNB-GW Access service. It must be entered a string of size 1 to 79.
Usage Guidelines
Use this command to configure the IPv4 or IPv6 address to be used as the connection point for establishing IKEv2 sessions for this HeNB-GW Access service, and the crypto template for the SecGW . The SecGW configuration includes crypto template configuration as part of IPSec settings. Therefore, if the crypto-template is defined in a different context than the current HeNB-GW Access service, the context name has to be specified.
Example
security gateway bind ipv4-address192.68.111.15 crypto-template crypto-temp
security-gateway ip
Configures the behavior of IP allocation when HeNB requests for a dual IP.
Product
HeNB-GW
Privilege
Security Administrator, Administrator
Mode
Exec > Global Configuration > Context Configuration > HeNBGW-Access Service Configuration
configure > context context_name > henbgw-access-service service_name
Entering the above command sequence results in the following prompt:
[context_name]host_name(config-henbgw-access-service)#
Syntax
Syntax Description
security-gateway ip alloc-mode { single | dual } default security-gateway ip alloc-mode
default
Restores the configuration to its default value.
Default: single
alloc-mode { single | dual }
Specifies to allocate a single or dual IP address.
single: On receiving a request for dual IP, the HeNB-GW access service will try to allocate an IPv6 address to HeNB. If the IPv6 address is unavailable, an IPv4 address will be allocated. This is the default behaviour.
dual: On receiving a request for dual IP, the HeNB-GW access service will allocate both IPv6 and IPv4 addresses to HeNB based on availability.
Usage Guidelines
Use this command to configure the behavior of IP allocation when HeNB requests for a dual IP.
Example
security gateway ip alloc-mode dual
timeout
Configures the the maximum duration of the session for this HeNB-GW Access service, in seconds, before system automatically reports/terminates the session.
Product
HeNB-GW
Privilege
Security Administrator, Administrator
Mode
Exec > Global Configuration > Context Configuration > HeNBGW-Access Service Configuration
configure > context context_name > henbgw-access-service service_name
Entering the above command sequence results in the following prompt:
[context_name]host_name(config-henbgw-access-service)#
Syntax
Syntax Description
timeout long-duration dur action { detection | disconnect } no timeout long-duration
no
Removes the currently setup maximum duration of session.
dur
Specifies the number of seconds for the session's timeout duration, before system automatically terminates the session or a defined action is to be taken.
dur is an integer from 1 through 2147483647. Default: 0
Usage Guidelines
Use this command to configure the maximum duration of the session, in seconds, before system automatically reports/terminates the session of this HeNB-GW Access service.
Example
timeout long-duration 60 action disconnect
Feedback