Out-Address Configuration Mode Commands

Mode

The Out-Address configuration mode provides the commands to configure the outbound parameters for the SCCP entities as part of the gtt-address-map configuration.

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)# 

Important

The commands or keywords/variables that are available are dependent on platform type, product version, and installed license(s).


do show

Executes all show commands while in Configuration mode.

Product

All

Privilege

Security Administrator, Administrator

Syntax

do show  

Usage Guidelines

Use this command to run all Exec mode show commands while in Configuration mode. It is not necessary to exit the Config mode to run a show command.

The pipe character | is only available if the command is valid in the Exec mode.


Caution

There are some Exec mode show commands which are too resource intensive to run from Config mode. These include: do show support collection , do show support details , do show support record and do show support summary . If there is a restriction on a specific show command, the following error message is displayed:

Failure: Cannot execute 'do	show support' command from Config mode.

end

Exits the configuration mode and returns to the Exec mode.

Product

SGSN

Privilege

Security Administrator, Administrator

Syntax

end  

Usage Guidelines

Change the mode back to the Exec mode.

exit

Exits the configuration mode and returns to the Global configuration mode.

Product

SGSN

Privilege

Security Administrator, Administrator

Syntax

exit  

Usage Guidelines

Return to the Global configuration mode.

gt-address

Configures the SCCP short address.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)# 

Syntax

gt-address  gt_address 

gt_address

A string of 1 to 15 digits to define the GT-address

Usage Guidelines

Define the GT-address

Examples

gt-address  010405525397 

gt-format

The GT-format provides four formats that can be used during GTT.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)# 

Syntax

gt-format  format_num 

format_num

1: Selects GT-format 1 options which include nature-of-address and odd/even. Once selected, the system enters GT-Format1 configuration mode.

2: Selects GT-format2 options which include translation-type . Once selected, the system enters GT-Format2 configuration mode.

3: Selects GT-format3 options which include encoding-scheme , numbering-plan3 and translation-type . Once selected, the system enters GT-Format1 configuration mode.

4: Selects GT-format4 options which include encoding-scheme , nature-of-address , numbering-plan , and translation-type . Once selected, the system enters GT-Format4 configuration mode.

Usage Guidelines

Select the a GT-format that include encoding-scheme as part of the GTT process.

Examples

gt-format  3 

ni-indicator

Configures the National and International indicator to use during the GTT process.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)# 

Syntax

ni-indicator  ni_ind 

ni_ind

Select one of the following as the appropriate type of national indicator for the address structure:
  • national

  • international

Usage Guidelines

Select the international indicator to be used for out-going addresses.

Examples

ni-indicator  international 

point-code

Selects and configures the SS7-type point code for use with the out-going address.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)# 

Syntax

point-code  pt_code 

pt_code

Enter 1 to 11 digits in the point code format predefined during variant selection of GTT association.

Usage Guidelines

Define an ITU point code to be used for out-going address processing.

Examples

point-code  6.255.6 

routing-indicator

Selects the type of routing and the indicator to be included in the out-going message.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)# 

Syntax

routing-indicator  routing_ind 

routing_ind

Select one of the following options:
  • gt : Inserts an indicator that identifies routing based on global title.

  • ssn : Inserts an indicator that identifies routing based on the subsystem number.

Usage Guidelines

Select global title as the appropriate routing indicator.

Examples

routing-indicator  gt 

ssf

Selects the subservice field as factor in the out-going address processing. ssf sets the network indicator in the subservice field for SS7 Message Signal Units (MSUs). The indicator carried in the message's routing information typically identifies the structure of the point code as a message from within a nation or as a message coming from outside the national - international.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)# 

Syntax

ssf  sub_svc_fld 

sub_svc_fld

Select one of the following options:
  • international: The network indicator identifies the message as international with a point code structure that does not match the national point code structure,

  • national: The network indicator identifies the messages as having a national point code structure.

  • reserved: Provides an alternate network indicator for national messages.

  • spare: Provides an alternate network indicator for international messages.

Usage Guidelines

Select the international NI for inclusion in out-going address subservice fields.

Examples

ssf  international 

ssn

Selects the subsystem number to be included in the out-going message.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)# 

Syntax

ssn  sub_sys_num 

sub_sys_num

Enter an integer from 1 to 255.

Usage Guidelines

Use subsystem number 44 in the out-going address.

Examples

ssn  44