Cell Trace Module Configuration Mode Commands

The Cell Trace Module Configuration Mode provides the commands to configure real time cell traffic trace parameters in a context.

Mode

Exec > Global Configuration > Context Configuration > Cell Trace Module Configuration

configure > context context_name > cell-trace-module

Entering the above command sequence results in the following prompt:

[context_name]host_name(config-cell-trace)# 

Important

The commands or keywords/variables that are available are dependent on platform type, product version, and installed license(s).


cell-trace

This command allows you to configure the Cell Traffic Trace transfer parameters.

Product

MME

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > Cell Trace Module Configuration

configure > context context_name > cell-trace-module

Entering the above command sequence results in the following prompt:

[context_name]host_name(config-cell-trace)# 

Syntax

cell-trace { purge { { storage-limit  storage_limit  | time-limit  time_limit  } [ max-files  max_files ] } | push-interval  interval | push-trigger { space-usage-percent  usage_precent } | remove-file-after-transfer | transfer-mode { pull [ module-only ] | push primary { encrypted-url  enc_url | url  url [ module-only ] } | use-harddisk }  
default cell-trace [ purge | push-interval | push-trigger | remove-file-after-transfer | transfer-mode | use-harddisk ]  
no cell-trace [ purge | remove-file-after-transfer | use-harddisk ]  

default

Configures this command with its default setting for the specified cell traffic trace parameters.

no

Deletes the specified cell traffic trace parameters.

purge { { storage-limit storage_limit | time-limit time_limit } [ max-files max_files ] }

Specifies to purge or delete the cell trace records based on "time" or "volume" to restrict hard-disk space usage for cell trace records.

storage-limit storage_limit : Specifies the storage space for the record files, in megabytes. storage_limit must be an integer from 10 to 143360.

time-limit time_limit : Specifies the time to delete record files, in seconds. time_limit must be an integer from 600 to 2592000.

max-files max_files : Specifies the maximum number of records to purge per iteration. max_files must be an integer 0 or ranging from 1000 to 10000. When value is set to 0, it deletes all records until purge limit is reached.

By default, no purge operation is performed by the VPNMGR module.

push-interval interval

Specifies the transfer interval in seconds to push cell traffic trace files to an external file server. interval must be an integer from 1 to 30.

Default: 1 second

push-trigger { space-usage-percent usage_precent }

Configures the disk utilization trigger for cell traffic trace files.

space-usage-percent usage_precent : Specifies the disk utilization percentage for triggering PUSH. usage_precent must be an integer from 10 to 80.

remove-file-after-transfer

Deletes the files from RAMFS after transfer to an external server. If the cell-trace use-harddisk command is not configured, it is recommended to use this command.

transfer-mode { pull [ module-only ] | push primary { encrypted-url enc_url | url url } [ module-only ] }

Configures the transfer mode for cell trace record files. Only one TCE address configuration is required and all files will be sent to this address irrespective of the TCE address received from eNodeB in S1AP cell tracing message. Both the addresses must be the same mostly.

pull [ module-only ] : Specifies that L-ESS pulls the cell trace files.

push primary { encrypted-url enc_url | url url } [ module-only ] : Specifies that ST pushes the cell trace files onto the configured L-ESS server. enc_url specifies the location where the cell trace files will be transferred and must be entered in encrypted format. url specifies the location where the cell trace files will be transferred and must be entered in the server URL format scheme://user:password@host:[port]/directory - string of size 1 to 1024.

If the module-only keyword is set, then the given configuration is applied only for the specific record type. The administrator can configure record transfer information for all record types separately or combined using the module-only keyword.

pull [ module-only ] :

Server URL in the format: scheme://user:password@host:[port]/directory - string of size 1 to 1024

If the module-only keyword is set, then the given configuration is applied only for the specific record type. The administrator can configure record transfer information for all record types separately or combined using the module-only keyword.

use-harddisk

Moves the cell trace files from RAMFS to /hd-raid/ and then transferred to an external server. It is recommended to use this command to prevent space on RAMFS becoming full.

Usage Guidelines

Use this command to configure the Cell Traffic Trace transfer parameters. The user must be in a non-local context when specifying the cell-trace-module command.

Example

The following command pushes the cell traffic trace files to an external file server in 20 seconds:
cell-trace push-interval 20  

do show

Executes all show commands while in Configuration mode.

Product

All

Privilege

Security Administrator, Administrator

Syntax

do show  

Usage Guidelines

Use this command to run all Exec mode show commands while in Configuration mode. It is not necessary to exit the Config mode to run a show command.

The pipe character | is only available if the command is valid in the Exec mode.


Caution

There are some Exec mode show commands which are too resource intensive to run from Config mode. These include: do show support collection , do show support details , do show support record and do show support summary . If there is a restriction on a specific show command, the following error message is displayed:

Failure: Cannot execute 'do	show support' command from Config mode.

end

Exits the current configuration mode and returns to the Exec mode.

Product

All

Privilege

Security Administrator, Administrator

Syntax

end  

Usage Guidelines

Use this command to return to the Exec mode.

exit

Exits the current mode and returns to the parent configuration mode.

Product

All

Privilege

Security Administrator, Administrator

Syntax

exit  

Usage Guidelines

Use this command to return to the parent configuration mode.

file

This command allows you to configure the file creation properties for cell trace records.

Product

All

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > Cell Trace Module Configuration

configure > context context_name > cell-trace-module

Entering the above command sequence results in the following prompt:

[context_name]host_name(config-cell-trace)# 

Syntax

file [ delete-timeout  seconds | directory  directory_name | field-separator { hyphen | omit | underscore } | rotation { num-records  num_records | time  rotation_time } | storage-limit  storage_limit | trap-on-file-delete ]  
default file [ delete-timeout | directory | field-separator | rotation | storage-limit | trap-on-file-delete ]  

default

Configures this command with its default value for the specified parameters.

file delete-timeout seconds

Configures the time to delete the completed cell traffic trace files after specified number of seconds. seconds must be an integer from 3600 through 31536000.

file directory directory_name

Specifies a subdirectory to be generated in the default directory /records/celltrace in which to store EDR files. directory_name must be an alphanumeric string of 1 through 191 characters.

file field-separator { hyphen | omit | underscore }

Specifies the field inclusion/exclusion type of separators between two fields of cell trace files.

  • hyphen : Specifies to use "-" (hyphen) as the field separator between file format fields.

  • omit : Excludes the field separator.

  • underscore : Specifies to use "_" (underscore) as the field separator between file format fields.

file rotation { num-records num_records | time rotation_time }

Specifies the criteria to rotate the record file. CDRMOD will hold the cell trace records in buffer and write them to the XML file only when the criteria configured by this command are met.

num-records num_records : Completes the file when the specified number of records are added. When the number of records in the buffer reaches the specified value, records will be written to the XML file. num_records must be an integer from 100 to 2000. Default: 1000.

time rotation_time : Completes the file based on file duration, time after which records will be written to XML file. num_records must be an integer from 1 to 30. Default: 1 second.

file storage-limit storage_limit

Configures the total available storage space on RAMFS for cell trace files. storage_limit must be an integer from 10485760 to 134217728. When the storage space is full, the oldest files on RAMFS will be deleted first to create space for new files.

file trap-on-file-delete

Instructs the system to send an SNMP notification (starCDRFileRemoved) when a cell trace file is deleted due to lack of space.

Usage Guidelines

Use this command to configure the file creation properties for cell trace records.

Example

The following command configures the time to delete the cell trace files after 4000 seconds:
file delete-timeout 4000