VideoStream Commands

show Commands

This section lists the show commands to display information about your VideoStream configuration settings.

show 802.11

To display basic 802.11a, 802.11b/g, or 802.11h network settings, use the show 802.11 command.

show 802.11{ a | b | h}

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

h

Specifies the 802.11h network.

Command Default

None.

Command History

Release Modification
8.3 This command was introduced.

Examples

This example shows to display basic 802.11a network settings:


>  show 802.11a
802.11a Network.................................. Enabled
11nSupport....................................... Enabled
      802.11a Low Band........................... Enabled
      802.11a Mid Band........................... Enabled
      802.11a High Band.......................... Enabled
802.11a Operational Rates
    802.11a 6M Rate.............................. Mandatory
    802.11a 9M Rate.............................. Supported
    802.11a 12M Rate............................. Mandatory
    802.11a 18M Rate............................. Supported
    802.11a 24M Rate............................. Mandatory
    802.11a 36M Rate............................. Supported
    802.11a 48M Rate............................. Supported
    802.11a 54M Rate............................. Supported
802.11n MCS Settings:
    MCS 0........................................ Supported
    MCS 1........................................ Supported
    MCS 2........................................ Supported
    MCS 3........................................ Supported
    MCS 4........................................ Supported
    MCS 5........................................ Supported
    MCS 6........................................ Supported
    MCS 7........................................ Supported
    MCS 8........................................ Supported
    MCS 9........................................ Supported
    MCS 10....................................... Supported
    MCS 11....................................... Supported
    MCS 12....................................... Supported
    MCS 13....................................... Supported
    MCS 14....................................... Supported
    MCS 15....................................... Supported
802.11n Status:
    A-MPDU Tx:
        Priority 0............................... Enabled
        Priority 1............................... Disabled
        Priority 2............................... Disabled
        Priority 3............................... Disabled
        Priority 4............................... Disabled
        Priority 5............................... Disabled
        Priority 6............................... Disabled
        Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
--More-- or (q)uit
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Enabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admission Control (CAC) configuration
Voice AC:
   Voice AC - Admission control (ACM)............ Disabled
   Voice max RF bandwidth........................ 75
   Voice reserved roaming bandwidth.............. 6
   Voice load-based CAC mode..................... Disabled
   Voice tspec inactivity timeout................ Disabled
   Voice Stream-Size............................. 84000
   Voice Max-Streams............................. 2
Video AC:
   Video AC - Admission control (ACM)............ Disabled
   Video max RF bandwidth........................ Infinite
   Video reserved roaming bandwidth.............. 0

This example shows how to display basic 802.11h network settings:


>  show 802.11h
802.11h ......................................... powerconstraint : 0
802.11h ......................................... channelswitch : Disable
802.11h ......................................... channelswitch mode : 0

Related Commands

show ap stats

show ap summary


show client summary

show network


show network summary

show port


show wlan

show 802.11 media-stream

To display the multicast-direct configuration state, use the show 802.11 media-stream command.

show 802.11 { a | b | h} media-stream media_stream_name

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

h

Specifies the 802.11h network.

media_stream_name

Specified media stream name.

Command Default

None.

Command History

Release Modification
7.6 This command was introduced in a release earlier than Release 7.6.

Command History

Release Modification
8.3 This command was introduced.

Examples

This example shows how to display the media-stream configuration:


> show 802.11a media-stream rrc
Multicast-direct................................. Enabled
Best Effort...................................... Disabled
Video Re-Direct.................................. Enabled
Max Allowed Streams Per Radio.................... Auto
Max Allowed Streams Per Client................... Auto
Max Video Bandwidth.............................. 0
Max Voice Bandwidth.............................. 75
Max Media Bandwidth.............................. 85
Min PHY Rate..................................... 6000
Max Retry Percentage............................. 80

Related Commands

show media-stream group summary


show media-stream client

To display the details for a specific media-stream client or a set of clients, use the show media-stream client command.

show media-stream client { media-stream_name | summary}

Syntax Description

media-stream_name

Name of the media-stream client of which the details is to be displayed.

summary

Displays the details for a set of media-stream clients.

Command Default

None.

Command History

Release Modification
8.3 This command was introduced.

Examples

This example shows how to display a summary media-stream clients:


> show media-stream client summary
Number of Clients................................ 1
Client Mac         Stream Name  Stream Type  Radio WLAN  QoS    Status
-----------------  -----------  -----------  ----  ----  ------ -------
00:1a:73:dd:b1:12  mountainview  MC-direct    2.4   2     Video  Admitted

Related Commands

show media-stream group summary


show media-stream group detail

To display the details for a specific media-stream group, use the show media-stream group detail command.

show media-stream group detail media-stream_name

Syntax Description

media-stream_name

Name of the media-stream group.

Command Default

None.

Command History

Release Modification
8.3 This command was introduced.

Examples

This example shows how to display media-stream group configuration details:


> show media-stream group detail abc
Media Stream Name................................ abc
Start IP Address................................. 227.8.8.8
End IP Address................................... 227.9.9.9
 RRC Parameters
 Avg Packet Size(Bytes).......................... 1200
 Expected Bandwidth(Kbps)........................ 300
 Policy.......................................... Admit
 RRC re-evaluation............................... periodic
 QoS............................................. Video
 Status.......................................... Multicast-direct
 Usage Priority.................................. 5
 Violation....................................... drop

Related Commands

show media-stream group summary


show media-stream group summary

To display the summary of the media stream and client information, use the show media-stream group summary command.

show media-stream group summary

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command History

Release Modification
7.6 This command was introduced in a release earlier than Release 7.6.

Command History

Release Modification
8.3 This command was introduced.

Examples

This example shows how to display a summary of the media-stream group:


(Cisco Controller) > show media-stream group summary
Stream Name   Start IP       End IP         Operation Status
------------- -------------- -------------- ----------------
abc           227.8.8.8      227.9.9.9      Multicast-direct

Related Commands

show 802.11 media-stream client

show media-stream client

show media-stream group detail

config Commands

This section lists the config commands to configure VideoStream settings on the controller.

config 802.11 cac video acm

To enable or disable video Call Admission Control (CAC) for the 802.11a or 802.11b/g network, use the config 802.11 cac video acm command.

config 802.11{ a | b} cac video acm { enable | disable}

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

enable

Enables video CAC settings.

disable

Disables video CAC settings.

Command Default

The default video CAC settings for the 802.11a or 802.11b/g network is disabled.

Usage Guidelines

CAC commands require that the WLAN you are planning to modify is configured for the Wi-Fi Multimedia (WMM) protocol and the quality of service (QoS) level be set to Platinum.

Before you can configure CAC parameters on a network, you must complete the following prerequisites:

  • Disable all WLANs with WMM enabled by entering the config wlan disable wlan_id command.

  • Disable the radio network you want to configure by entering the config 802.11{a | b} disable network command.

  • Save the new configuration by entering the save config command.

  • Enable voice or video CAC for the network you want to configure by entering the config 802.11{a | b} cac voice acm enable, or config 802.11{a | b} cac video acm enable commands.

Command History

Release Modification
8.3 This command was introduced.

Examples

The following example shows how to enable the video CAC for the 802.11a network: 


(Cisco Controller) > config 802.11 cac video acm enable

The following example shows how to disable the video CAC for the 802.11b network: 


(Cisco Controller) > config 802.11 cac video acm disable

Related Commands

config 802.11 cac video max-bandwidth


config 802.11 cac video roam-bandwidth


config 802.11 cac video tspec-inactivity-timeout

config 802.11 cac video cac-method

To configure the Call Admission Control (CAC) method for video applications on the 802.11a or 802.11b/g network, use the config 802.11 cac video cac-method command.

config 802.11 { a | b} cac video cac-method { static | load-based}

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

static

Enables the static CAC method for video applications on the 802.11a or 802.11b/g network.

Static or bandwidth-based CAC enables the client to specify how much bandwidth or shared medium time is required to accept a new video request and in turn enables the access point to determine whether it is capable of accommodating the request.

load-based

Enables the load-based CAC method for video applications on the 802.11a or 802.11b/g network.

Load-based or dynamic CAC incorporates a measurement scheme that takes into account the bandwidth consumed by all traffic types from itself, from co-channel access points, and by collocated channel interference. Load-based CAC also covers the additional bandwidth consumption results from PHY and channel impairment. The access point admits a new call only if the channel has enough unused bandwidth to support that call.

Load-based CAC is not supported if SIP-CAC is enabled.

Command Default

Static.

Usage Guidelines

CAC commands for video applications on the 802.11a or 802.11b/g network require that the WLAN you are planning to modify is configured for the Wi-Fi Multimedia (WMM) protocol and the quality of service (QoS) level be set to Gold.

Before you can configure CAC parameters on a network, you must complete the following prerequisites:

  • Disable all WLANs with WMM enabled by entering the config wlan disable wlan_id command.

  • Disable the radio network you want to configure by entering the config 802.11{a | b} disable network command.

  • Save the new configuration by entering the save config command.

  • Enable voice or video CAC for the network you want to configure by entering the 
config 802.11{a | b} cac voice acm enable or config 802.11{a | b} cac video acm enable command.

Video CAC consists of two parts: Unicast Video-CAC and MC2UC CAC. If you need only Unicast Video-CAC, you must configure only static mode. If you need only MC2UC CAC, you must configure Static or Load-based CAC. Load-based CAC is not supported if SIP-CAC is enabled.

Command History

Release Modification
8.3 This command was introduced.

Examples

This example shows how to enable the static CAC method for video applications on the 802.11a network: 

(Cisco Controller) > config 802.11 cac video cac-method static

Related Commands

show cac voice stats

show cac voice summary

show cac video stats

show cac video summary

config 802.11 cac video tspec-inactivity-timeout

config 802.11 cac video max-bandwidth

config 802.11 cac video acm

config 802.11 cac video sip

config 802.11 cac video roam-bandwidth

config 802.11 cac load-based

config 802.11 cac defaults

config 802.11 cac media-stream

config 802.11 cac multimedia

debug cac

config 802.11 cac video load-based

To enable or disable load-based Call Admission Control (CAC) for video applications on the 802.11a or 802.11b/g network, use the config 802.11 cac video load-based command.

config 802.11 { a | b} cac video load-based { enable | disable}

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

enable

Enables load-based CAC for video applications on the 802.11a or 802.11b/g network.

Load-based or dynamic CAC incorporates a measurement scheme that takes into account the bandwidth consumed by all traffic types from itself, from co-channel access points, and by collocated channel interference. Load-based CAC also covers the additional bandwidth consumption results from PHY and channel impairment. The access point admits a new call only if the channel has enough unused bandwidth to support that call.

disable

Disables load-based CAC method for video applications on the 802.11a or 802.11b/g network.

Command Default

Disabled.

Usage Guidelines

CAC commands for video applications on the 802.11a or 802.11b/g network require that the WLAN you are planning to modify is configured for the Wi-Fi Multimedia (WMM) protocol and the quality of service (QoS) level be set to Gold.

Before you can configure CAC parameters on a network, you must complete the following prerequisites:

  • Disable all WLANs with WMM enabled by entering the config wlan disable wlan_id command.

  • Disable the radio network you want to configure by entering the config 802.11{a | b} disable network command.

  • Save the new configuration by entering the save config command.

  • Enable voice or video CAC for the network you want to configure by entering the 
config 802.11{a | b} cac voice acm enable or config 802.11{a | b} cac video acm enable command.

Video CAC consists of two parts: Unicast Video-CAC and MC2UC CAC. If you need only Unicast Video-CAC, you must configure only static mode. If you need only MC2UC CAC, you must configure Static or Load-based CAC. Load-based CAC is not supported if SIP-CAC is enabled.


Note

Load-based CAC is not supported if SIP-CAC is enabled.

Command History

Release Modification
8.3 This command was introduced.

Examples

This example shows how to enable load-based CAC method for video applications on the 802.11a network: 

(Cisco Controller) > config 802.11 cac video load-based enable

Related Commands

show cac voice stats

show cac voice summary

show cac video stats

show cac video summary

config 802.11 cac video tspec-inactivity-timeout

config 802.11 cac video max-bandwidth

config 802.11 cac video acm

config 802.11 cac video sip

config 802.11 cac video roam-bandwidth

config 802.11 cac load-based

config 802.11 cac defaults

config 802.11 cac media-stream

config 802.11 cac multimedia

config 802.11 cac video cac-method

debug cac

config 802.11 cac video max-bandwidth

To set the percentage of the maximum bandwidth allocated to clients for video applications on the 802.11a or 802.11b/g network, use the config 802.11 cac video max-bandwidth command.

config 802.11{ a | b} cac video max-bandwidth bandwidth

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

bandwidth

Bandwidth percentage value from 5 to 85%.

Command Default

The default maximum bandwidth allocated to clients for video applications on the 802.11a or 802.11b/g network is 0%.

Usage Guidelines

The maximum radio frequency (RF) bandwidth cannot exceed 85% for voice and video. Once the client reaches the value specified, the access point rejects new calls on this network.


Note

If this parameter is set to zero (0), the controller assumes that you do not want to allocate any bandwidth and allows all bandwidth requests.

Call Admission Control (CAC) commands require that the WLAN you are planning to modify is configured for the Wi-Fi Multimedia (WMM) protocol and the quality of service (QoS) level be set to Platinum.

Before you can configure CAC parameters on a network, you must complete the following prerequisites:

  • Disable all WLANs with WMM enabled by entering the config wlan disable wlan_id command.

  • Disable the radio network you want to configure by entering the config 802.11{a | b} disable network command.

  • Save the new configuration by entering the save config command.

  • Enable voice or video CAC for the network you want to configure by entering the config 802.11{a | b} cac voice acm enable, or config 802.11{a | b} cac video acm enable commands.

Command History

Release Modification
8.3 This command was introduced.

Examples

The following example shows how to specify the percentage of the maximum allocated bandwidth for video applications on the selected radio band: 


(Cisco Controller) > config 802.11 cac video max-bandwidth 50

Related Commands

config 802.11 cac video acm


config 802.11 cac video roam-bandwidth


config 802.11 cac voice stream-size

config 802.11 cac voice roam-bandwidth

config 802.11 cac media-stream

To configure media stream Call Admission Control (CAC) voice and video quality parameters for 802.11a and 802.11b networks, use the config 802.11 cac media-stream command.

config 802.11 { a | b} cac media-stream multicast-direct { max-retry-percent retry-percentage | min-client-rate dot11-rate}

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

multicast-direct

Configures CAC parameters for multicast-direct media streams.

max-retry-percent

Configures the percentage of maximum retries that are allowed for multicast-direct media streams.

retry-percentage

Percentage of maximum retries that are allowed for multicast-direct media streams.

min-client-rate

Configures the minimum transmission data rate to the client for multicast-direct media streams.

dot11-rate

Minimum transmission data rate to the client for multicast-direct media streams. Rate in kbps at which the client can operate.

If the transmission data rate is below this rate, either the video will not start or the client may be classified as a bad client. The bad client video can be demoted for better effort QoS or subject to denial. The available data rates are 6000, 9000, 12000, 18000, 24000, 36000, 48000, 54000, and 11n rates.

Command Default

The default value for the maximum retry percent is 80. If it exceeds 80, either the video will not start or the client might be classified as a bad client. The bad client video will be demoted for better effort QoS or is subject to denial.

Usage Guidelines

CAC commands for video applications on the 802.11a or 802.11b/g network require that the WLAN you are planning to modify is configured for Wi-Fi Multimedia (WMM) protocol and the quality of service (QoS) level be set to Gold.

Before you can configure CAC parameters on a network, you must complete the following prerequisites:

  • Disable all WLANs with WMM enabled by entering the config wlan disable wlan_id command.

  • Disable the radio network you want to configure by entering the config 802.11{a | b} disable network command.

  • Save the new configuration by entering the save config command.

  • Enable voice or video CAC for the network you want to configure by entering the 
config 802.11{a | b} cac voice acm enable or config 802.11{a | b} cac video acm enable command.

Command History

Release Modification
8.3 This command was introduced.

Examples

The following example shows how to configure the maximum retry percent for multicast-direct media streams as 90 on a 802.11a network: 

(Cisco Controller) > config 802.11 cac media-stream multicast-direct max-retry-percent 90

Related Commands

show cac voice stats

show cac voice summary

show cac video stats

show cac video summary

config 802.11 cac video tspec-inactivity-timeout

config 802.11 cac video max-bandwidth

config 802.11 cac video acm

config 802.11 cac video sip

config 802.11 cac video roam-bandwidth

config 802.11 cac load-based

config 802.11 cac defaults

config 802.11 cac multimedia

debug cac

config 802.11 cac multimedia

To configure the CAC media voice and video quality parameters for 802.11a and 802.11b networks, use the config 802.11 cac multimedia command.

config 802.11 { a | b} cac multimedia max-bandwidth bandwidth

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

max-bandwidth

Configures the percentage of maximum bandwidth allocated to Wi-Fi Multimedia (WMM) clients for voice and video applications on the 802.11a or 802.11b/g network.

bandwidth

Percentage of the maximum bandwidth allocated to WMM clients for voice and video applications on the 802.11a or 802.11b/g network. Once the client reaches the specified value, the access point rejects new calls on this radio band. The range is from 5 to 85%.

Command Default

The default maximum bandwidth allocated to Wi-Fi Multimedia (WMM) clients for voice and video applications on the 802.11a or 802.11b/g network is 85%.

Usage Guidelines

Call Admission Control (CAC) commands for video applications on the 802.11a or 802.11b/g network require that the WLAN you are planning to modify is configured for Wi-Fi Multimedia (WMM) protocol and the quality of service (QoS) level be set to Gold.

Before you can configure CAC parameters on a network, you must complete the following prerequisites:

  • Disable all WLANs with WMM enabled by entering the config wlan disable wlan_id command.

  • Disable the radio network you want to configure by entering the config 802.11{a | b} disable network command.

  • Save the new configuration by entering the save config command.

  • Enable voice or video CAC for the network you want to configure by entering the 
config 802.11{a | b} cac voice acm enable or config 802.11{a | b} cac video acm enable command.

Command History

Release Modification
8.3 This command was introduced.

Examples

The following example shows how to configure the percentage of the maximum bandwidth allocated to WMM clients for voice and video applications on the 802.11a network: 

(Cisco Controller) > config 802.11 cac multimedia max-bandwidth 80

Related Commands

show cac voice stats

show cac voice summary

show cac video stats

show cac video summary

config 802.11 cac video tspec-inactivity-timeout

config 802.11 cac video max-bandwidth

config 802.11 cac video acm

config 802.11 cac video sip

config 802.11 cac video roam-bandwidth

config 802.11 cac load-based

config 802.11 cac defaults

debug cac

config 802.11 cac video roam-bandwidth

To configure the percentage of the maximum allocated bandwidth reserved for roaming video clients on the 802.11a or 802.11b/g network, use the config 802.11 cac video roam-bandwidth command.

config 802.11{ a | b} cac video roam-bandwidth bandwidth

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

bandwidth

Bandwidth percentage value from 5 to 85%.

Command Default

The maximum allocated bandwidth reserved for roaming video clients on the 802.11a or 802.11b/g network is 0%.

Command History

Release Modification
7.6 This command was introduced in a release earlier than Release 7.6.

Command History

Release Modification
8.3 This command was introduced.

Usage Guidelines

The controller reserves the specified bandwidth from the maximum allocated bandwidth for roaming video clients.


Note

If this parameter is set to zero (0), the controller assumes that you do not want to do any bandwidth allocation and, therefore, allows all bandwidth requests.

CAC commands require that the WLAN you are planning to modify is configured for the Wi-Fi Multimedia (WMM) protocol and the quality of service (QoS) level be set to Platinum.

Before you can configure CAC parameters on a network, you must complete the following prerequisites:

  • Disable all WLANs with WMM enabled by entering the config wlan disable wlan_id command.

  • Disable the radio network you want to configure by entering the config 802.11 {a | b} disable network command.

  • Save the new configuration by entering the save config command.

  • Enable voice or video CAC for the network you want to configure by entering the 
config 802.11 {a | b} cac voice acm enable or config 802.11 {a | b} cac video acm enable command.

    For complete instructions, see the “Configuring Voice and Video Parameters” section in the “Configuring Controller Settings” chapter of the Cisco Wireless LAN Controller Configuration Guide for your release.

Examples

The following example shows how to specify the percentage of the maximum allocated bandwidth reserved for roaming video clients on the selected radio band: 


(Cisco Controller) > config 802.11 cac video roam-bandwidth 10

Related Commands

config 802.11 cac video tspec-inactivity-timeout

config 802.11 cac video max-bandwidth

config 802.11 cac video acm

config 802.11 cac video cac-method

config 802.11 cac video sip

config 802.11 cac video load-based

config 802.11 cac video tspec-inactivity-timeout

To process or ignore the Call Admission Control (CAC) Wi-Fi Multimedia (WMM) traffic specifications (TSPEC) inactivity timeout received from an access point, use the config 802.11 cac video tspec-inactivity-timeout command.

config 802.11{ a | b} cac video tspec-inactivity-timeout { enable | ignore}

Syntax Description

a

Specifies the 802.11a network.

ab

Specifies the 802.11b/g network.

enable

Processes the TSPEC inactivity timeout messages.

ignore

Ignores the TSPEC inactivity timeout messages.

Command Default

The default CAC WMM TSPEC inactivity timeout received from an access point is disabled (ignore).

Command History

Release Modification
8.3 This command was introduced.

Usage Guidelines

CAC commands require that the WLAN you are planning to modify is configured for the Wi-Fi Multimedia (WMM) protocol and the quality of service (QoS) level be set to Platinum.

Before you can configure CAC parameters on a network, you must complete the following prerequisites:

  • Disable all WLANs with WMM enabled by entering the config wlan disable wlan_id command.

  • Disable the radio network you want to configure by entering the config 802.11{a | b} disable network command.

  • Save the new configuration by entering the save config command.

  • Enable voice or video CAC for the network you want to configure by entering the 
config 802.11{a | b} cac voice acm enable or config 802.11{a | b} cac video acm enable commands.

Examples

This example shows how to process the response to TSPEC inactivity timeout messages received from an access point: 


(Cisco Controller) > config 802.11a cac video tspec-inactivity-timeout enable

This example shows how to ignore the response to TSPEC inactivity timeout messages received from an access point: 


(Cisco Controller) > config 802.11a cac video tspec-inactivity-timeout ignore

Related Commands

config 802.11 cac video acm


config 802.11 cac video max-bandwidth

config 802.11 cac video roam-bandwidth

config 802.11 cac voice acm

To enable or disable bandwidth-based voice Call Admission Control (CAC) for the 802.11a or 802.11b/g network, use the config 802.11 cac voice acm command.

config 802.11{ a | b} cac voice acm { enable | disable}

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

enable

Enables the bandwidth-based CAC.

disable

Disables the bandwidth-based CAC.

Command Default

The default bandwidth-based voice CAC for the 802.11a or 802.11b/g network id disabled.

Command History

Release Modification
8.3 This command was introduced.

Usage Guidelines

CAC commands require that the WLAN you are planning to modify is configured for the Wi-Fi Multimedia (WMM) protocol and the quality of service (QoS) level be set to Platinum.

Before you can configure CAC parameters on a network, you must complete the following prerequisites:

  • Disable all WLANs with WMM enabled by entering the config wlan disable wlan_id command.

  • Disable the radio network you want to configure by entering the config 802.11{a | b} disable network command.

  • Save the new configuration by entering the save config command.

  • Enable voice or video CAC for the network you want to configure by entering the 
config 802.11{a | b} cac voice acm enable or config 802.11{a | b} cac video acm enable commands.

Examples

This example shows how to enable the bandwidth-based CAC: 


(Cisco Controller) > config 802.11c cac voice acm enable

This example shows how to disable the bandwidth-based CAC: 


(Cisco Controller) > config 802.11b cac voice acm disable

Related Commands

config 802.11 cac video acm


config 802.11 cac voice max-bandwidth

To set the percentage of the maximum bandwidth allocated to clients for voice applications on the 802.11a or 802.11b/g network, use the config 802.11 cac voice max-bandwidth command.

config 802.11{ a | b} cac voice max-bandwidth bandwidth

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

bandwidth

Bandwidth percentage value from 5 to 85%.

Command Default

The default maximum bandwidth allocated to clients for voice applications on the 802.11a or 802.11b/g network is 0%.

Usage Guidelines

The maximum radio frequency (RF) bandwidth cannot exceed 85% for voice and video. Once the client reaches the value specified, the access point rejects new calls on this network.

CAC commands require that the WLAN you are planning to modify is configured for the Wi-Fi Multimedia (WMM) protocol and the quality of service (QoS) level be set to Platinum.

Before you can configure CAC parameters on a network, you must complete the following prerequisites:

  • Disable all WLANs with WMM enabled by entering the config wlan disable wlan_id command.

  • Disable the radio network you want to configure by entering the config 802.11{a | b} disable network command.

  • Save the new configuration by entering the save config command.

  • Enable voice or video CAC for the network you want to configure by entering the 
config 802.11{a | b} cac voice acm enable or config 802.11{a | b} cac video acm enable commands.

Command History

Release Modification
8.3 This command was introduced.

Examples

The following example shows how to specify the percentage of the maximum allocated bandwidth for voice applications on the selected radio band: 


(Cisco Controller) > config 802.11a cac voice max-bandwidth 50

Related Commands

config 802.11 cac voice roam-bandwidth

config 802.11 cac voice stream-size

config 802.11 exp-bwreq 


config 802.11 tsm

config wlan
save

show wlan


show wlan summary

config 802.11 cac voice tspec-inactivity-timeout

config 802.11 cac voice load-based

config 802.11 cac video acm

config 802.11 cac voice roam-bandwidth

To configure the percentage of the Call Admission Control (CAC) maximum allocated bandwidth reserved for roaming voice clients on the 802.11a or 802.11b/g network, use the config 802.11 cac voice roam-bandwidth command.

config 802.11{ a | b} cac voice roam-bandwidth bandwidth

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

bandwidth

Bandwidth percentage value from 0 to 85%.

Command Default

The default CAC maximum allocated bandwidth reserved for roaming voice clients on the 802.11a or 802.11b/g network is 85%.

Usage Guidelines

The maximum radio frequency (RF) bandwidth cannot exceed 85% for voice and video. The controller reserves the specified bandwidth from the maximum allocated bandwidth for roaming voice clients.


Note

If this parameter is set to zero (0), the controller assumes you do not want to allocate any bandwidth and therefore allows all bandwidth requests.

CAC commands require that the WLAN you are planning to modify is configured for the Wi-Fi Multimedia (WMM) protocol and the quality of service (QoS) level be set to Platinum.

Before you can configure CAC parameters on a network, you must complete the following prerequisites:

  • Disable all WLANs with WMM enabled by entering the config wlan disable wlan_id command.

  • Disable the radio network you want to configure by entering the config 802.11{a | b} disable network command.

  • Save the new configuration by entering the save config command.

  • Enable voice or video CAC for the network you want to configure by entering the 
config 802.11{a | b} cac voice acm enable or config 802.11{a | b} cac video acm enable commands.

Command History

Release Modification
8.3 This command was introduced.

Examples

The following example shows how to configure the percentage of the maximum allocated bandwidth reserved for roaming voice clients on the selected radio band: 


(Cisco Controller) > config 802.11 cac voice roam-bandwidth 10

Related Commands

config 802.11 cac voice acm

config 802.11cac voice max-bandwidth

config 802.11 cac voice stream-size

config 802.11 cac voice tspec-inactivity-timeout

To process or ignore the Wi-Fi Multimedia (WMM) traffic specifications (TSPEC) inactivity timeout received from an access point, use the config 802.11 cac voice tspec-inactivity-timeout command.

config 802.11{ a | b} cac voice tspec-inactivity-timeout { enable | ignore}

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

enable

Processes the TSPEC inactivity timeout messages.

ignore

Ignores the TSPEC inactivity timeout messages.

Command Default

The default WMM TSPEC inactivity timeout received from an access point is disabled (ignore).

Usage Guidelines

Call Admission Control (CAC) commands require that the WLAN you are planning to modify is configured for Wi-Fi Multimedia (WMM) protocol and the quality of service (QoS) level be set to Platinum.

Before you can configure CAC parameters on a network, you must complete the following prerequisites:

  • Disable all WLANs with WMM enabled by entering the config wlan disable wlan_id command.

  • Disable the radio network you want to configure by entering the config 802.11{a | b} disable network command.

  • Save the new configuration by entering the save config command.

  • Enable voice or video CAC for the network you want to configure by entering the 
config 802.11{a | b} cac voice acm enable or config 802.11{a | b} cac video acm enable commands.

Command History

Release Modification
8.3 This command was introduced.

Examples

The following example shows how to enable the voice TSPEC inactivity timeout messages received from an access point: 



(Cisco Controller) > config 802.11 cac voice tspec-inactivity-timeout enable

Related Commands


config 802.11 cac voice load-based

config 802.11 cac voice roam-bandwidth


config 802.11 cac voice acm

config 802.11cac voice max-bandwidth

config 802.11 cac voice stream-size

config 802.11 cac voice load-based

To enable or disable load-based Call Admission Control (CAC) for the 802.11a or 802.11b/g network, use the config 802.11 cac voice load-based command.

config 802.11{ a | b} cac voice load-based { enable | disable}

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

enable

Enables load-based CAC.

disable

Disables load-based CAC.

Command Default

The default load-based CAC for the 802.11a or 802.11b/g network is disabled.

Usage Guidelines

CAC commands require that the WLAN you are planning to modify is configured for the Wi-Fi Multimedia (WMM) protocol and the quality of service (QoS) level be set to Platinum.

Before you can configure CAC parameters on a network, you must complete the following prerequisites:

  • Disable all WLANs with WMM enabled by entering the config wlan disable wlan_id command.

  • Disable the radio network you want to configure by entering the config 802.11{a | b} disable network command.

  • Save the new configuration by entering the save config command.

  • Enable voice or video CAC for the network you want to configure by entering the 
config 802.11{a | b} cac voice acm enable or config 802.11{a | b} cac video acm enable commands.

Command History

Release Modification
8.3 This command was introduced.

Examples

The following example shows how to enable the voice load-based CAC parameters: 


(Cisco Controller) > config 802.11a cac voice load-based enable

The following example shows how to disable the voice load-based CAC parameters: 


(Cisco Controller) > config 802.11a cac voice load-based disable

Related Commands

config 802.11 cac voice tspec-inactivity-timeout

config 802.11 cac video max-bandwidth

config 802.11 cac video acm

config 802.11 cac voice stream-size

config 802.11 cac voice max-calls


Note

Do not use the config 802.11 cac voice max-calls command if the SIP call snooping feature is disabled and if the SIP based Call Admission Control (CAC) requirements are not met.

To configure the maximum number of voice call supported by the radio, use the config 802.11 cac voice max-calls command.

config 802.11{ a | b} cac voice max-calls number

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

number

Number of calls to be allowed per radio.

Command Default

The default maximum number of voice call supported by the radio is 0, which means that there is no maximum limit check for the number of calls.

Usage Guidelines

CAC commands require that the WLAN you are planning to modify is configured for the Wi-Fi Multimedia (WMM) protocol and the quality of service (QoS) level be set to Platinum.

Before you can configure CAC parameters on a network, you must complete the following prerequisites:

  • Disable all WLANs with WMM enabled by entering the config wlan disable wlan_id command.

  • Disable the radio network you want to configure by entering the config 802.11{a | b} disable network command.

  • Save the new configuration by entering the save config command.

  • Enable voice or video CAC for the network you want to configure by entering the 
config 802.11{a | b} cac voice acm enable or config 802.11{a | b} cac video acm enable commands.

Command History

Release Modification
8.3 This command was introduced.

Examples

The following example shows how to configure the maximum number of voice calls supported by radio: 


(Cisco Controller) > config 802.11 cac voice max-calls 10

Related Commands

config 802.11 cac voice roam-bandwidth

config 802.11 cac voice stream-size

config 802.11 exp-bwreq 


config 802.11 cac voice tspec-inactivity-timeout

config 802.11 cac voice load-based

config 802.11 cac video acm

config 802.11 cac voice stream-size

To configure the number of aggregated voice Wi-Fi Multimedia (WMM) traffic specification (TSPEC) streams at a specified data rate for the 802.11a or 802.11b/g network, use the config 802.11 cac voice stream-size command.

config 802.11{ a | b} cac voice stream-size stream_size number mean_datarate max-streams mean_datarate

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

stream-size

Configures the maximum data rate for the stream.

stream_size

Range of stream size is between 84000 and 92100.

number

Number (1 to 5) of voice streams.

mean_datarate

Configures the mean data rate.

max-streams

Configures the mean data rate of a voice stream.

mean_datarate

Mean data rate (84 to 91.2 kbps) of a voice stream.

Command Default

The default number of streams is 2 and the mean data rate of a stream is 84 kbps.

Usage Guidelines

Call Admission Control (CAC) commands require that the WLAN you are planning to modify is configured for the Wi-Fi Multimedia (WMM) protocol and the quality of service (QoS) level be set to Platinum.

Before you can configure CAC parameters on a network, you must complete the following prerequisites:

  • Disable all WLANs with WMM enabled by entering the config wlan disable wlan_id command.

  • Disable the radio network you want to configure by entering the config 802.11{a | b} disable network command.

  • Save the new configuration by entering the save config command.

  • Enable voice or video CAC for the network you want to configure by entering the 
config 802.11{a | b} cac voice acm enable or config 802.11{a | b} cac video acm enable commands.

Command History

Release Modification
8.3 This command was introduced.

Examples

The following example shows how to configure the number of aggregated voice traffic specifications stream with the stream size 5 and the mean data rate of 85000 kbps: 


(Cisco Controller) > config 802.11 cac voice stream-size 5 max-streams size 85

Related Commands

config 802.11 cac voice acm


config 802.11 cac voice load-based 


config 802.11 cac voice max-bandwidth

config 802.11 cac voice roam-bandwidth

config 802.11 cac voice tspec-inactivity-timeout


config 802.11 exp-bwreq

config advanced 802.11 edca-parameters

To enable a specific Enhanced Distributed Channel Access (EDCA) profile on a 802.11a network, use the config advanced 802.11 edca-parameters command.

config advanced 802.11{ a | b} edca-parameters { wmm-default | svp-voice | optimized-voice | optimized-video-voice | custom-voice | | custom-set { QoS Profile Name } { aifs AP-value (0-16 ) Client value (0-16) | ecwmax AP-Value (0-10) Client value (0-10) | ecwmin AP-Value (0-10) Client value (0-10) | txop AP-Value (0-255) Client value (0-255) } }

Syntax Description

a

Specifies the 802.11a network.

b

Specifies the 802.11b/g network.

wmm-default

Enables the Wi-Fi Multimedia (WMM) default parameters. Choose this option if voice or video services are not deployed on your network.

svp-voice

Enables Spectralink voice-priority parameters. Choose this option if Spectralink phones are deployed on your network to improve the quality of calls.

optimized-voice

Enables EDCA voice-optimized profile parameters. Choose this option if voice services other than Spectralink are deployed on your network.

optimized-video-voice

Enables EDCA voice-optimized and video-optimized profile parameters. Choose this option when both voice and video services are deployed on your network.

Note   

If you deploy video services, admission control must be disabled.

custom-voice

Enables custom voice EDCA parameters for 802.11a. The EDCA parameters under this option also match the 6.0 WMM EDCA parameters when this profile is applied.

custom-set

Enables customization of EDCA parameters

  • aifs—Configures the Arbitration Inter-Frame Space.

    AP Value (0-16) Client value (0-16)

  • ecwmax—Configures the maximum Contention Window.

    AP Value(0-10) Client Value (0-10)

  • ecwmin—Configures the minimum Contention Window.

    AP Value(0-10) Client Value(0-10)

  • txop—Configures the Arbitration Transmission Opportunity Limit.

    AP Value(0-255) Client Value(0-255)

QoS Profile Name - Enter the QoS profile name:

  • bronze

  • silver

  • gold

  • platinum

Command Default

The default EDCA parameter is wmm-default.

Command History

Release Modification
8.3 This command was introduced.

Examples

The following example shows how to enable Spectralink voice-priority parameters: 


(Cisco Controller) > config advanced 802.11 edca-parameters svp-voice

Related Commands

config advanced 802.11b edca-parameters

Enables a specific Enhanced Distributed Channel Access (EDCA) profile on the 802.11a network.

show 802.11a

Displays basic 802.11a network settings.

config 802.11 media-stream multicast-direct

To configure the media stream multicast-direct parameters for the 802.11 networks, use the config 802.11 media-stream multicast-direct command.

config 802.11{ a | b} media-stream multicast-direct { admission-besteffort { enable | disable} | { client-maximum | radio-maximum} { value | no-limit } | enable | disable}

Syntax Description

802.11a

Specifies the 802.11a network.

802.11b

Specifies the 802.11b/g network.

admission-besteffort

Admits media stream to best-effort queue.

enable

Enables multicast-direct on a 2.4-GHz or a 5-GHz band.

disable

Disables multicast-direct on a 2.4-GHz or a 5-GHz band.

client-maximum

Specifies the maximum number of streams allowed on a client.

radio-maximum

Specifies the maximum number of streams allowed on a 2.4-GHz or a 5-GHz band.

value

Number of streams allowed on a client or on a 2.4-GHz or a 5-GHz band, between 1 to 20.

no-limit

Specifies the unlimited number of streams allowed on a client or on a 2.4-GHz or a 5-GHz band.

Command Default

None

Command History

Release Modification
7.6 This command was introduced in a release earlier than Release 7.6.

Command History

Release Modification
8.3 This command was introduced.

Usage Guidelines

Before you configure the media stream multicast-direct parameters on a 802.11 network, ensure that the network is nonoperational.

Examples

This example shows how to enable a media stream multicast-direct settings on an 802.11a network:


> config 802.11a media-stream multicast-direct enable

This example shows how to admit the media stream to the best-effort queue:


> config 802.11a media-stream multicast-direct admission-besteffort enable

This example shows how to set the maximum number of streams allowed on a client:


> config 802.11a media-stream multicast-direct client-maximum 10

Related Commands

config 802.11 media-stream video-redirect

show 802.11a media-stream name

show media-stream group summary

show media-stream group detail

config 802.11 media-stream video-redirect

To configure the media stream video-redirect for the 802.11 networks, use the config 802.11 media-stream video-redirect command.

config 802.11{ a | b} media-stream video-redirect { enable | disable}

Syntax Description

802.11a

Specifies the 802.11a network.

802.11b

Specifies the 802.11b/g network.

enable

Enables traffic redirection.

disable

Disables traffic redirection.

Command Default

None.

Command History

Release Modification
8.3 This command was introduced.

Usage Guidelines

Before you configure the media stream video-redirect on a 802.11 network, ensure that the network is nonoperational.

Examples

This example shows how to enable media stream traffic redirection on an 802.11a network:


> config 802.11a media-stream video-redirect enable

Related Commands

config 802.11 media-stream multicast-redirect

show 802.11a media-stream name

show media-stream group summary

show media-stream group detail

config media-stream multicast-direct

To configure the media-stream multicast direct, use the config media-stream multicast direct command.

config media-stream multicast-direct { enable | disable}

Syntax Description

enable

Enables a media stream.

disable

Disables a media stream.

Command Default

None.

Command History

Release Modification
8.3 This command was introduced.

Usage Guidelines

Media-stream multicast-direct requires load based Call Admission Control (CAC) to run.

Examples

This example shows how to enable media-stream multicast-direct settings:


> config media-stream multicast-direct enable

This example shows how to disable media-stream multicast-direct settings:


> config media-stream multicast-direct disable

Related Commands

config 802.11 media-stream video-redirect

show 802.11a media-stream name

show media-stream group summary

show media-stream group detail

config media-stream message

To configure various parameters of message configuration, use the config media-stream message command.

config media-stream message { state [ enable | disable] | url url | email email | phone phone_number | note note}

Syntax Description

state

Specifies the media stream message state.

enable

(Optional) Enables the session announcement message state.

disable

(Optional) Disables the session announcement message state.

url

Configures the URL.

url

Session announcement URL.

email

Configures the email ID.

email

Specifies the session announcement e-mail.

phone

Configures the phone number.

phone_number

Session announcement phone number.

note

Configures the notes.

note

Session announcement notes.

Command Default

Disabled.

Command History

Release Modification
8.3 This command was introduced.

Usage Guidelines

Media-stream multicast-direct requires load-based Call Admission Control (CAC) to run.

Examples

This example shows how to enable the session announcement message state:


> config media-stream message state enable

This example shows how to configure the session announcement e-mail address:


> config media-stream message mail abc@co.com

Related Commands

config media-stream

show 802.11a media-stream name

show media-stream group summary

show media-stream group detail

config media-stream add

To configure the various global media-stream configurations, use the config media-stream add command.

config media-stream add multicast-direct media_stream_name start-IP end-IP [ template { very coarse | coarse | ordinary | low-resolution | med-resolution | high-resolution} | detail { bandwidth packet-size { periodic| initial}} qos priority { drop | fallback}

Syntax Description

multicast-direct

Specifies the media stream for the multicast-direct setting.

media_stream_name

Media-stream name.

start-IP

IP multicast destination start address.

end-IP

IP multicast destination end address.

template

(Optional) Configures the media stream from templates.

very coarse

Applies a very-coarse template.

coarse

Applies a coarse template.

ordinary

Applies an ordinary template.

low-resolution

Applies a low-resolution template.

med-resolution

Applies a medium-resolution template.

high-resolution

Applies a high-resolution template.

detail

Configures the media stream with specific parameters.

bandwidth

Maximum expected stream bandwidth.

packet-size

Average packet size.

periodic

Specifies the periodic admission evaluation.

initial

Specifies the Initial admission evaluation.

qos

AIR QoS class (video only).

priority

Media-stream priority.

drop

Specifies that the stream is dropped on a periodic reevaluation.

fallback

Specifies if the stream is demoted to the best-effort class on a periodic reevaluation.

Command Default

None

Command History

Release Modification
7.6 This command was introduced in a release earlier than Release 7.6.

Command History

Release Modification
8.3 This command was introduced.

Usage Guidelines

Media-stream multicast-direct requires load-based Call Admission Control (CAC) to run.

Examples

This example shows how to configure a new media stream:

> config media-stream add multicast-direct abc 227.8.8.8 227.9.9.9 detail 2 150 periodic video 1 drop

Related Commands

show 802.11a media-stream name

show media-stream group summary

show media-stream group detail

config media-stream admit

To allow traffic for a media stream group, use the config media-stream admit command.

config media-stream admit media_stream_name

Syntax Description

media_stream_name

Media-stream group name.

Command Default

None

Command History

Release Modification
7.6 This command was introduced in a release earlier than Release 7.6.

Command History

Release Modification
8.3 This command was introduced.

Usage Guidelines

When you try to allow traffic for the media stream group, you will be prompted that IGMP snooping will be disabled and enabled again, and all clients might observe a glitch on the multicast traffic.

Examples

This example shows how to allow traffic for a media stream group:


(Cisco Controller) > config media-stream admit MymediaStream

Related Commands

show 802.11a media-stream name

show media-stream group summary

show media-stream group detail

config media-stream deny

To block traffic for a media stream group, use the config media-stream deny command.

Syntax Description

media_stream_name

Media-stream group name.

config media-stream deny media_stream_name

Command Default

None

Command History

Release Modification
7.6 This command was introduced in a release earlier than Release 7.6.

Command History

Release Modification
8.3 This command was introduced.

Usage Guidelines

When you try to block traffic for the media stream group, you will be prompted that IGMP snooping will be disabled and enabled again, and all clients might observe a glitch on the multicast traffic.

Examples

This example shows how to block traffic for a media stream group:


(Cisco Controller) > config media-stream deny MymediaStream

Related Commands

show 802.11a media-stream name

show media-stream group summary

show media-stream group detail

config media-stream delete

To configure the various global media-stream configurations, use the config media-stream delete command.

config media-stream delete media_stream_name

Syntax Description

media_stream_name

Media-stream name.

Command Default

None

Command History

Release Modification
7.6 This command was introduced in a release earlier than Release 7.6.

Command History

Release Modification
8.3 This command was introduced.

Usage Guidelines

Media-stream multicast-direct requires load-based Call Admission Control (CAC) to run.

Examples

This example shows how to delete the media stream named abc:


(Cisco Controller) > config media-stream delete abc

Related Commands

show 802.11a media-stream name

show media-stream group summary

show media-stream group detail

config wlan media-stream

To configure multicast-direct for a wireless LAN media stream, use the config wlan media-stream command.

config wlan media-stream multicast-direct { wlan_id | all} { enable | disable}

Syntax Description

multicast-direct

Configures multicast-direct for a wireless LAN media stream.

wlan_id

Wireless LAN identifier between 1 and 512.

all

Configures the wireless LAN on all media streams.

enable

Enables global multicast to unicast conversion.

disable

Disables global multicast to unicast conversion.

Command Default

None

Command History

Release Modification
8.3 This command was introduced.

Usage Guidelines

Media stream multicast-direct requires load based Call Admission Control (CAC) to run. WLAN quality of service (QoS) needs to be set to either gold or platinum.

Examples

The following example shows how to enable the global multicast-direct media stream with WLAN ID 2:


(Cisco Controller) >config wlan media-stream multicast-direct 2 enable