Table Of Contents
gateway address (ccn subsystem sip)
gateway port (ccn subsystem sip)
groupname notification cascade-to after
groupname profile (phone-device)
G
Last Updated: June 30, 2007
gateway address (ccn subsystem sip)
gateway port (ccn subsystem sip)
groupname notification cascade-to after
groupname profile (phone-device)
gateway address (ccn subsystem sip)
To configure the IP address of the SIP proxy server, use the gateway address command in Cisco Unity Express SIP configuration mode. To remove the address, use the no form of this command.
gateway address ip-address
no gateway address
Syntax Description
Defaults
IP address 0.0.0.0
Command Modes
Cisco Unity Express SIP configuration
Command History
Examples
The following example configures a SIP proxy server address of 10.2.34.1:
se-10-0-0-0> enablese-10-0-0-0# config tse-10-0-0-0(config)# ccn subsystem sipse-10-0-0-0(config-sip)# gateway address 10.2.34.1se-10-0-0-0(config-sip)# endse-10-0-0-0(config)#Related Commands
gateway port (ccn subsystem sip)
To configure the UDP or TCP port on the SIP proxy server, use the gateway port command in Cisco Unity Express SIP configuration mode. To remove the port, use the no form of this command.
gateway port port-number
no gateway port
Syntax Description
Defaults
Port 5060
Command Modes
Cisco Unity Express SIP configuration
Command History
Examples
The following example configures the SIP proxy server port to 23:
se-10-0-0-0> enablese-10-0-0-0# config tse-10-0-0-0(config)# ccn subsystem sipse-10-0-0-0(config-sip)# gateway port 23se-10-0-0-0(config-sip)# endse-10-0-0-0(config)#Related Commands
groupname
To configure a Cisco Unity Express group, use the groupname command in either Cisco Unity Express EXEC mode or configuration mode.
EXEC Mode
groupname name [create | delete | description "description" | fullname display "full-name"]
Configuration Mode
groupname name [create | member username | owner ownername | phonenumber phone-number | phonenumberE164 full-number | privilege privilege-name]
Syntax Description
Command Modes
Cisco Unity Express EXEC
Cisco Unity Express configurationCommand History
Usage Guidelines
The EXEC version of the command stores the permitted information in Cisco Unity Express flash memory. If a problem with the disk occurs, this information is available so that the group members may access the group's voice mailbox.
The configuration version of the command is stored in the Cisco Unity Express system configuration file. If a power outage or a system shutdown occurs, the group information can be retrieved.
Several privileges are available:
•Superuser—An administrator, also called a superuser, has the capability, or privilege, of accessing all the configuration and maintenance functions, including the Administration via Telephone (AvT).
•ManagePrompts—The prompt management subscriber has access to the AvT but not to any other administrative functions.
•Broadcast—The broadcast privilege permits the subscriber to send broadcast messages across the network.
•ManagePublicList—The ManagePublicList privilege permits the subscriber to create and modify public distribution lists.
•ViewPrivateList—The ViewPrivateList privilege allows the subscriber to view another subscriber's private distribution lists. The ViewPrivateList subscriber can not modify or delete the private lists.
These privilege levels are assigned to a group, and any member of the group is granted the privilege rights. The software initialization process created an Administrator group from the imported subscribers designated as administrators. Other groups can be created with these privileges. Assign subscribers to an existing group using the CLI commands or the GUI option Configuration > Users.
Assign the vm-imap privilege to one or more groups so that the group members can access the integrated messaging feature. Subscribers who are not members of a group with the vm-imap privilege will not be able to access the integrated messaging feature.
To display the current list of privileges, use the show privileges command in Cisco Unity Express EXEC mode. Use the show groups privileges command to display the privileges assigned to each group.
Examples
The following example creates the group Sales with two members, one owner, and two privileges:
se-10-0-0-0> enablese-10-0-0-0# groupname sales fullname display "Sales New York"se-10-0-0-0# groupname sales description "Sales group in New York branch"se-10-0-0-0# config tse-10-0-0-0(config)# groupname sales phonenumber 50120se-10-0-0-0(config)# groupname sales phonenumberE164 12225550120se-10-0-0-0(config)# groupname sales member user4se-10-0-0-0(config)# groupname sales member user5se-10-0-0-0(config)# groupname sales owner user6se-10-0-0-0(config)# groupname sales privilege broadcastse-10-0-0-0(config)# groupname sales privilege ManagePublicListse-10-0-0-0(config)# exitThe following example assigns the integrated messaging feature to the sales group:
se-10-0-0-0# config tse-10-0-0-0(config)# groupname sales privilege vm-imapse-10-0-0-0(config)# exitThe following example assigns the local broadcast privilege to the engineers group:
se-10-0-0-0# config tse-10-0-0-0(config)# groupname engineers privilege local-broadcastse-10-0-0-0(config)# exitRelated Commands
groupname notification cascade-to after
To define a rule for cascading a notification, use the groupname notification cascade-to after command in Cisco Unity Express EXEC mode. Use the no form of this command to remove the rule and disable cascading to the specified group.
groupname group-id notification cascade-to uid after minutes
no groupname group-id notification cascade-to uid after minutes
Syntax Description
Command Default
There are no notification cascading rules defined for the subscriber.
Command Modes
Cisco Unity Express EXEC
Command History
Usage Guidelines
Use the groupname notification cascade-to after command in Cisco Unity Express configuration mode to define:
•The group for whom notification cascading is being configured.
•The group to whom cascaded notification is being sent.
•The amount of time after which the notification cascade occurs.
An error message appears when:
•The specified group, or profile does not exist on the local system.
•The group exists but a rule is already defined to cascade to that group.
•The group does not have a mailbox.
•The group cannot define a rule to cascade notification to himself.
•The maximum number of groups have already been configured for cascading.
•The time is outside the allowed range.
•The time is within the allowed range, but a rule is already defined to cascade notification at that time.
Examples
The following example define a rule to cascade notification from group22 to group 42 after 10 minutes:
se-10-0-0-0# groupname group22 notification cascade-to group42 after 10Related Commands
groupname privilege
To assign viewing privileges for the Cisco Unity Express IVR reporting historical or real-time statistics, use the groupname command in global configuration mode. Use the no form of this command to delete the historical report viewing privileges from the specified group.
groupname group-name privilege {ViewHistoricalReports | ViewRealTime}
no groupname group-name privilege {ViewHistoricalReports | ViewRealTime}
Syntax Description
Command Default
None
Command Modes
Global configuration
Command History
Usage Guidelines
The Cisco Unity Express IVR real-time statistics collection tool provides real-time statistics for key workflow components, such as contacts, application tasks, and engine tasks. This feature provides summary or detailed real-time statistics for each contract or application. With real-time statistics, the summary values provide only the information accumulated since the last time the statistics were cleared. Clear the accumulated summary statistical data manually, by using the GUI interface, or automatically at midnight, by setting up a daily schedule.
If the specified group does not exist on the system, an error message appears.
Examples
The following example assigns Cisco Unity Express IVR historical statistics report viewing privileges to the groupname myGroup:
se-10-0-0-0# config tse-10-0-0-0(config)# groupname myGroup privilege ViewHIstoricalReportsse-10-0-0-0(config)# exitse-10-0-0-0#Related Commands
groupname profile (phone-device)
To configure a group's cell phone for message notification, use the groupname profile (phone device) command in Cisco Unity Express EXEC mode. To remove or deactivate a parameter from the cell phone, use the no or default form of this command.
groupname group-id profile vm-notif-profile {cell-phone | home-phone | work-phone}
{enable
extra-digits digits
phonenumber phonenumber
preference {all | urgent}
schedule day day-of-week active from hh:mm to hh:mm}no groupname group-id profile vm-notif-profile {cell-phone | home-phone | work-phone}
{enable
extra-digits digits
phonenumber phonenumber
preference {all | urgent}
schedule day day-of-week active from hh:mm to hh:mm}default groupname group-id profile vm-notif-profile {cell-phone | home-phone | work-phone} preference {all | urgent}
Syntax Description
Defaults
Cell phone notifications are disabled.
Default preference is urgent.Command Modes
Cisco Unity Express EXEC
Command History
Usage Guidelines
The system creates one default notification profile with the filename vm-notif-profile per group. This filename cannot be changed.
Repeat the command with the schedule parameter to configure more than one time slot. This parameter changes only the specified time slots; the configuration for the other time slots is not changed.
An error message appears for the following conditions:
•The group does not exist in the system.
•The group does not have a mailbox.
•phonenumber is a restricted number.
•More than 64 digits are entered for digits.
•A valid phone number is not assigned to the device.
•The administrator has disabled message notification on a system-wide basis.
•The system-wide notification preference is set to urgent and an attempt is made to set this group's preference to all.
•The schedule start time is later than the schedule end time.
Using the no or default form of this command results in the following conditions:
•no groupname group-id profile vm-notif-profile {cell-phone | home-phone | work-phone} enable disables the sending of notifications to the device.
•no groupname group-id profile vm-notif-profile {cell-phone | home-phone | work-phone} extra-digits removes the extra digits assigned to the device.
•no groupname group-id profile vm-notif-profile {cell-phone | home-phone | work-phone} phonenumber removes the phone number from the device and automatically disables the device.
•no (or default) groupname group-id profile vm-notif-profile {cell-phone | home-phone | work-phone} preference sets the notification preference to urgent.
•no groupname group-id profile vm-notif-profile {cell-phone | home-phone | work-phone} schedule day day-of-week active from hh:mm to hh:mm deactivates the sending of notifications for the specified time slot.
Examples
The following example configures the cell phone for group sales:
se-10-0-0-0# groupname sales profile vm-notif-profile cell-phone phonenumber 12225550150se-10-0-0-0# groupname sales profile vm-notif-profile cell-phone enablese-10-0-0-0# groupname sales profile vm-notif-profile cell-phone extra-digits 9se-10-0-0-0# groupname sales profile vm-notif-profile cell-phone allse-10-0-0-0# groupname sales profile vm-notif-profile cell-phone schedule day 2 active from 08:00 to 17:00se-10-0-0-0# groupname sales profile vm-notif-profile cell-phone schedule day 3 active from 08:00 to 12:00se-10-0-0-0# groupname sales profile vm-notif-profile cell-phone schedule day 4 active from 13:00 to 16:00se-10-0-0-0# groupname sales profile vm-notif-profile cell-phone schedule day 5 active from 08:00 to 14:00se-10-0-0-0# groupname sales profile vm-notif-profile cell-phone schedule day 6 active from 08:00 to 17:00Related Commands
groupname profile email
To configure a group's e-mail for message notification, use the groupname profile email command in Cisco Unity Express EXEC mode. To remove or deactivate a parameter from the e-mail device, use the no or default form of this command.
groupname group-id profile vm-notif-profile email
{address email-address
attach
enable
preference {all | urgent}
schedule day day-of-week active from hh:mm to hh:mm
text email-text}no groupname group-id profile vm-notif-profile email
{address email-address
attach
enable
preference {all | urgent}
schedule day day-of-week active from hh:mm to hh:mm
text email-text}default groupname group-id profile vm-notif-profile email attach
default groupname group-id profile vm-notif-profile email preference {all | urgent}
Syntax Description
Defaults
E-mail notifications are disabled.
E-mail attachments are disabled.
Default preference is urgent.Command Modes
Cisco Unity Express EXEC
Command History
Usage Guidelines
The system creates one default notification profile with the filename vm-notif-profile per group. This filename cannot be changed.
Repeat the command with the schedule parameter to configure more than one time slot. This parameter changes only the specified time slots; the configuration for the other time slots is not changed.
An error message appears for the following conditions:
•The group does not exist in the system.
•The group does not have a mailbox.
•The administrator has disabled message notification on a system-wide basis.
•The administrator has disabled e-mail attachments on a system-wide basis.
•E-mail is enabled before the e-mail address is defined.
•E-mail is enabled and an SMTP server is not configured.
•The system-wide notification preference is set to urgent and an attempt is made to set this group's preference to all.
•The schedule start time is later than the schedule end time.
•E-mail text contains a question mark (?).
•E-mail text is longer than 128 characters.
Using the no or default form of this command results in the following conditions:
•no groupname group-id profile vm-notif-profile email enable disables the sending of notifications to the device.
•no groupname group-id profile vm-notif-profile email address email-address removes the e-mail address assigned to the device and automatically disables the device.
•no (or default) groupname group-id profile vm-notif-profile email attach disables attaching voice messages to outgoing e-mail notifications for this device.
•no (or default) groupname group-id profile vm-notif-profile email preference sets the notification preference to urgent.
•no groupname group-id profile vm-notif-profile email schedule day day-of-week active from hh:mm to hh:mm deactivates the sending of notifications for the specified time slot.
•no groupname group-id profile vm-notif-profile email text removes the text associated with this device.
Examples
The following example configures the cell phone for group sales:
se-10-0-0-0# groupname sales profile vm-notif-profile email address group1@company.comse-10-0-0-0# groupname sales profile vm-notif-profile email enablese-10-0-0-0# groupname sales profile vm-notif-profile email attachse-10-0-0-0# groupname sales profile vm-notif-profile email allse-10-0-0-0# groupname sales profile vm-notif-profile email schedule day 3 active from 08:00 to 10:00se-10-0-0-0# groupname sales profile vm-notif-profile email text "Sales meeting scheduled in main office conference room C 1:00-3:00 p.m. 4/19/06"Related Commands
groupname profile num-pager
To configure a group's numeric pager for message notification, use the groupname profile num-pager command in Cisco Unity Express EXEC mode. To remove or deactivate a parameter from the home phone, use the no or default form of this command.
groupname group-id profile vm-notif-profile num-pager
{enable
extra-digits digits
phonenumber phonenumber
preference {all | urgent}
schedule day day-of-week active from hh:mm to hh:mm}no groupname group-id profile vm-notif-profile num-pager
{enable
extra-digits digits
phonenumber phonenumber
preference {all | urgent}
schedule day day-of-week active from hh:mm to hh:mm}default groupname group-id profile vm-notif-profile num-pager preference {all | urgent}
Syntax Description
Defaults
Numeric pager notifications are disabled.
Default preference is urgent.Command Modes
Cisco Unity Express EXEC
Command History
Usage Guidelines
The system creates one default notification profile with the filename vm-notif-profile per group. This filename cannot be changed.
Repeat the command with the schedule parameter to configure more than one time slot. This parameter changes only the specified time slots; the configuration for the other time slots is not changed.
An error message appears for the following conditions:
•The group does not exist in the system.
•The group does not have a mailbox.
•phonenumber is a restricted number.
•More than 64 digits are entered for digits.
•A valid phone number is not assigned to the device.
•The administrator has disabled message notification on a system-wide basis.
•The system-wide notification preference is set to urgent and an attempt is made to set this group's preference to all.
•The schedule start time is later than the schedule end time.
Using the no or default form of this command results in the following conditions:
•no groupname group-id profile vm-notif-profile num-pager enable disables the sending of notifications to the device.
•no groupname group-id profile vm-notif-profile num-pager extra-digits removes the extra digits assigned to the device.
•no groupname group-id profile vm-notif-profile num-pager phonenumber removes the phone number from the device and automatically disables the device.
•no (or default) groupname group-id profile vm-notif-profile num-pager preference sets the notification preference to urgent.
•no groupname group-id profile vm-notif-profile num-pager schedule day day-of-week active from hh:mm to hh:mm deactivates the sending of notifications for the specified time slot.
Examples
The following example configures the cell phone for group sales:
se-10-0-0-0# groupname sales profile vm-notif-profile num-pager phonenumber 12225550150se-10-0-0-0# groupname sales profile vm-notif-profile num-pager enablese-10-0-0-0# groupname sales profile vm-notif-profile num-pager extra-digits 9se-10-0-0-0# groupname sales profile vm-notif-profile num-pager allse-10-0-0-0# groupname sales profile vm-notif-profile num-pager schedule day 2 active from 08:00 to 17:00se-10-0-0-0# groupname sales profile vm-notif-profile num-pager schedule day 3 active from 08:00 to 12:00se-10-0-0-0# groupname sales profile vm-notif-profile num-pager schedule day 4 active from 13:00 to 16:00se-10-0-0-0# groupname sales profile vm-notif-profile num-pager schedule day 5 active from 08:00 to 14:00se-10-0-0-0# groupname sales profile vm-notif-profile num-pager schedule day 6 active from 08:00 to 17:00Related Commands
groupname profile text-pager
To configure a group's text pager for message notification, use the groupname profile text-pager command in Cisco Unity Express EXEC mode. To remove or deactivate a parameter from the text pager device, use the no or default form of this command.
groupname group-id profile vm-notif-profile text-pager
{address email-address
enable
preference {all | urgent}
schedule day day-of-week active from hh:mm to hh:mm
text email-text}no groupname group-id profile vm-notif-profile text-pager
{address email-address
enable
preference {all | urgent}
schedule day day-of-week active from hh:mm to hh:mm
text message-text}default groupname group-id profile vm-notif-profile text-pager preference {all | urgent}
Syntax Description
Defaults
Text pager notifications are disabled.
Default preference is urgent.Command Modes
Cisco Unity Express EXEC
Command History
Usage Guidelines
The system creates one default notification profile with the filename vm-notif-profile per group. This filename cannot be changed.
Repeat the command with the schedule parameter to configure more than one time slot. This parameter changes only the specified time slots; the configuration for the other time slots is not changed.
An error message appears for the following conditions:
•The group does not exist in the system.
•The group does not have a mailbox.
•The administrator has disabled message notification on a system-wide basis.
•Text paging is enabled before the e-mail address is defined.
•Text paging is enabled and an SMTP server is not configured.
•The system-wide notification preference is set to urgent and an attempt is made to set this group's preference to all.
•The schedule start time is later than the schedule end time.
•Message text contains a question mark (?).
•Message text is longer than 128 characters.
Using the no or default form of this command results in the following conditions:
•no groupname group-id profile vm-notif-profile text-pager enable disables the sending of notifications to the device.
•no groupname group-id profile vm-notif-profile text-pager address email-address removes the e-mail address assigned to the device and automatically disables the device.
•no (or default) groupname group-id profile vm-notif-profile text-pager preference sets the notification preference to urgent.
•no groupname group-id profile vm-notif-profile text-pager schedule day day-of-week active from hh:mm to hh:mm deactivates the sending of notifications for the specified time slot.
•no groupname group-id profile vm-notif-profile text-pager text removes the text associated with this device.
Examples
The following example configures the cell phone for group sales:
se-10-0-0-0# groupname sales profile vm-notif-profile text-pager address sales@company.comse-10-0-0-0# groupname sales profile vm-notif-profile text-pager enablese-10-0-0-0# groupname sales profile vm-notif-profile text-pager allse-10-0-0-0# groupname sales profile vm-notif-profile text-pager schedule day 3 active from 08:00 to 10:00se-10-0-0-0# groupname sales profile vm-notif-profile text-pager text "Sales meeting scheduled in main office conference room C 1:00-3:00 p.m. 4/19/06"Related Commands