|
Configuration Parameter
|
Definition
|
*.autonomous |
Enables a process, for example the engine, to be started without the system. Default: false Note  Do not change this value. |
| |
|
*.ClearingLocation |
Specifies whether the Clearing Location field in Call Context is overridden before outputting LRelease from LCM. The reason this may be needed is as follows:-NI2+ from the NAS always sends a clearing location of USER, which is generally mapped to clearing location of USER, but the switch receiving the release message may want to receive a location of TRANSIT so that the call can be re-routed. This clearing location property provides this ability. Values: •0 = Normal mapping behavior, LCM will not override the Clearing Location field in Call Context. •1 = LCM will override the Clearing Location in Call Context with LOCATION_USER •2 = LCM will override the Clearing Location in Call Context with LOCATION_ PRIVATE_LOCAL •3 = LCM will override the Clearing Location in Call Context with LOCATION_ PUBLIC_LOCAL •4 = LCM will override the Clearing Location in Call Context with LOCATION_TRANSIT •5 = LCM will override the Clearing Location in Call Context with LOCATION_ PUBLIC_REMOTE •6 = LCM will override the Clearing Location in Call Context with LOCATION_ PRIVATE_REMOTE •7 = LCM will override the Clearing Location in Call Context with LOCATION_ INTERNATIONAL •8 = LCM will override the Clearing Location in Call Context with LOCATION_ INTERWORKING •9 = LCM will override the Clearing Location in Call Context with LOCATION_ LOCAL_INTERFACE •10 = LCM will override the Clearing Location in Call Context with LOCATION_ LOCAL_LOCAL •11 = LCM will override the Clearing Location in Call Context with LOCATION_ LOCAL_REMOTE •12 = LCM will override the Clearing Location in Call Context with LOCATION_ PACKET_MANAGER •13 = LCM will override the Clearing Location in Call Context with LOCATION_ UNKNOWN Default: 0 (Normal mapping behavior) Note Option 13 may not be valid for all solutions. |
*.chkPtPort |
Port number used between peer components or processes for check-pointing. Value: Any unused port number. Default: 2001 Leave this value as the default. Note If you have two Cisco MGC hosts in a failover configuration, both fields in the XECfgParm.dat files should contain the same value. |
*.CPUTimerInterval |
Specify the interval, in milliseconds, at which the CPU utilization level of the Cisco MGC is sampled. Recommended Value: 500 - 2000 milliseconds. Default: 1000. |
*.dataDir |
Location of the data directory. Default: ../var Note Do not change this value. |
*.dataSourceName |
Used by the MMDB to obtain the data source name for the ODBC connection. Default: howdydb Note Do not change this value. |
*.debugLevel |
Determines level of debugging detail if debugging is initiated. Default: high Note Do not change this value. |
*.DefaultLocation |
Specifies whether to override the default location field in call context. This is so that the user can define a customer-specific default location for the system, which may differ from the default location set in the type definition of the protocol. The default location property provides this ability. Values: •0 = Normal protocol-defined default value; LCM will not override the default location field in call context. •1 = LCM will override the default location in call context with LOCATION_USER •2 = LCM will override the default location in call context with LOCATION_ PRIVATE_LOCAL •3 = LCM will override the default location in call context with LOCATION_ PUBLIC_LOCAL •4 = LCM will override the default location in call context with LOCATION_TRANSIT •5 = LCM will override the default location in call context with LOCATION_ PUBLIC_REMOTE •6 = LCM will override the default location in call context with LOCATION_ PRIVATE_REMOTE •7 = LCM will override the default location in call context with LOCATION_ INTERNATIONAL •8 = LCM will override the default location in call context with LOCATION_ INTERWORKING •9 = LCM will override the default location in call context with LOCATION_ LOCAL_INTERFACE •10 = LCM will override the default location in call context with LOCATION_ LOCAL_LOCAL •11 = LCM will override the default location in call context with LOCATION_ LOCAL_REMOTE •12 = LCM will override the default location in call context with LOCATION_ PACKET_MANAGER •13 = LCM will override the default location in call context with LOCATION_ UNKNOWN Default: 0 (Normal protocol-defined default value) Note Option 13 may not be valid for all solutions. |
*.desiredPlatformState |
Determines the desired platform state. Values: •master, if you have two (active and standby) Cisco MGC hosts •slave, if you have two (active and standby) Cisco MGC hosts •standalone, if you have a single-host system Default: none Note The value used is site specific. For example, use the values master and slave if you have two (active and standby) Cisco MGC hosts. Enter standalone if you have a single-host system. |
*.disableMeas |
Disables the collection of measurement data. Values: true = disables data collection false = data is collected Default: false Note Do not change this value. |
*.eventTrace |
Used by developers only to trace events at the application level. |
engine.SysGSMTimerInterval |
Allows group service messages (GSMs—used to advertise the state of circuits) to be sent at a periodic rate from the SS7 side of the network to the IP side of the network. Valid values: 1000 to 15000 Default: 15000 |
*.FastConnect |
Allows LCM messages to pass through. Values: 0 = Passes all signals to LCM 1 = Disables signal to LCM for "CallProceeding" received from NAS 2 = Disables signal to LCM for "CallProceeding" or "Progress" received from NAS 3 = Disables signal to LCM for "CallProceeding", "Progress", or "Alerting" received from NAS. |
*.GWClearChannelAlgorithm |
Allows the use of the clear channel 64K unrestricted data transfer between gateways. Values: •null = do not use clear channel algorithm •clear channel = use clear channel algorithm Default: null |
*.homeDirRoot |
Location of the home directory. Default: /opt/CiscoMGC Note Do not change this value. |
ioChanCtl.ituIsNewZealand |
At startup, the IOCM reads the ioChanCtl.ituIsNewZealand boolean flag in XECfgParm.dat to see if the ITU implementation of MTP3 is to be set with NewZealand specific parameters. If the flag is set to true, then the associated MTP3 parameters are set to meet the following requirements: •The MTP3 restart procedure must be disabled. The SS7 IOCC currently provides this capability by setting timers T20 and T21 to zero. •The priority of all MTP3 messages must be set to zero. •The RCT (Route Congestion Test) Procedure must be disabled.
Note Set this parameter to true if running in or connecting to the Telecom New Zealand network.
|
*.IP_Addr1 |
IP address of interface 1; used for signaling. |
*.IP_Addr2 |
IP address of interface 2; used for signaling. |
*.IP_Addr3 |
IP address of interface 3 (if installed); used for signaling. |
*.IP_Addr4 |
IP address of interface 4 (if installed); used for signaling. |
*.ipAddrLocalA |
First local IP address; used for checkpointing and failover heartbeats if you have active/standby Cisco MGC hosts. Note This is typically the same value as *.IP_Addr1. |
*.ipAddrLocalB |
Second local IP address; used for checkpointing and failover heartbeats if you have active/standby Cisco MGC hosts. Note If your configuration does not use an external card, leave this setting as the default value, 0.0. |
*.ipAddrPeerA |
First corresponding peer IP address; used for checkpointing and failover heartbeats. Note If you have two Cisco MGC hosts in a failover configuration, this value is the IP address of the second host. |
*.ipAddrPeerB |
Second corresponding peer IP address; used for checkpointing and failover heartbeats. Note If your configuration does not use an external card, leave this setting as the default value, 0.0. |
*.logDirectory |
Location of the active and rotated log files. Default: ../var/log Note Make sure the log file has write permission for the LogServer. |
*.logFileNamePrefix |
Combined with the .log extension, defines the filename for log files. Default: platform Example: engine Note This setting can also redirect process messages from the default log file to a specified log file. For example, engine.logFileNamePrefix = engine instructs the log server to redirect messages from the engine process to the dedicated engine.log file. This functions with or without *.logDirectory. |
*.logMsgDrop |
Controls whether the log server drops debug-level messages when the UNIX domain socket used for log server communication is full. Values: •true = debug messages are dropped •false = debug messages are not dropped Default: true Note If you set this parameter to false for the engine and the engine logging level is Debug, the system can fail at high call rates. |
*.logPrio |
Defines the initial default logging level used by logging clients when sending messages to the logging server. Use the chg-log MML command to change logging levels after installation. You can specify different logging levels for each process. For example, engine.logPrio = Info Note This setting is the only way to modify the logging level of the current MML process. The chg-log command does not affect current MML process logging levels. Values: Note The values for this parameter are case sensitive, and the first letter must be capitalized. •Debug—This priority is used only for detailed debugging messages. Logging at this priority is not recommended during production because this causes a large volume of messages to be logged, which degrades system performance and can cause failover problems. •Trace—These messages capture protocol traffic. This priority is used for debugging. •Info—These messages indicate an operation that is proceeding as expected. •Warning—These messages indicate a problem exists that does not prevent the system from operating. This is the normal, default logging level for production. •Error—These messages indicate an unexpected error that is recoverable but degrades performance. •Critical—These messages indicate errors so severe that a process cannot continue operating. Default: Error Note Do not change this value unless you are debugging. |
*.LongCallTime |
Monitors call length and sets the system to trigger an alarm when a call length reaches a certain level. Default: 21600000 milliseconds (6 hours) Note Typically, leave this value as the default. You can change it, if necessary, based on billing requirements. |
*.MDLANumberScreening |
Specifies which number to use as the A Number screening value. Values: •0 = use Calling Party Number •1= use Redirecting Number Default: 0 |
*.MgcpBehavior |
Regulates VSC engine behavior to allow different MGCP gateway types to return different codes for the same error. Value range: Integer •0—No action •1—Prevents the VSC from reusing a circuit after a CRCX failure (return code 501); VISM and MX8260 •2—Prevents the VSC from reusing a circuit after a CRCX failure (return code 502); 5300 Default: 0 Note Additional differences can be handled by adding enumerated values. |
*.numberOfThreads |
Specifies the number of threads generated by multi-threaded processes such as the engine, the log master, and so on. Corresponds to the number of CPUs in your configuration. Values: •0 = single CPU •1 = two CPUs •2 = four CPUs Default: 0 Note If you have a multi-CPU system (1 or 2), you must set engine.SysGeneratedCode to true. |
*.Ovl1AbateThresh |
Controls engine overload levels. This setting depends on the specified percentage of CPU utilization. If the Ovl1OnsetThreshold is reached, raising an alarm, the Ovl1RejectPercent action abates until this threshold value is reached, clearing the alarm. Value: 0 to 100 percent Default: 75 Note This value must be less than Ovl1OnsetThresh. |
*.Ovl1OnsetThresh |
Controls engine overload levels. This setting depends on the specified percentage of CPU utilization. If this threshold value is met, an alarm is raised and calls are rejected at the percentage defined by Ovl1RejectPercent. Value: 0 to 100 percent Default: 82 |
*.Ovl1RejectPercent |
Controls engine overload levels. This setting depends on the specified percentage of CPU utilization. A percentage of new calls is rejected at this level. For example, 20% means that 1 out of 5 new calls are rejected at this level. Value: 0 to 100 percent Default: 25 percent |
*.Ovl2AbateThresh |
Controls engine overload levels. This setting depends on the specified percentage of CPU utilization. If the Ovl2OnsetThreshold is reached, raising an alarm, the Ovl2RejectPercent action abates until this threshold value is reached, clearing the alarm. Value: 0 to 100 percent Default: 77 Note This value must be less than Ovl2OnsetThresh |
*.Ovl2OnsetThresh |
Controls engine overload levels. This setting depends on the specified percentage of CPU utilization. If this threshold value is met, an alarm is raised and calls are rejected at the percentage defined by Ovl2RejectPercent. Value: 0 to 100 percent Default: 90 |
*.Ovl2RejectPercent |
Controls engine overload levels. This setting depends on the specified percentage of CPU utilization. A percentage of new calls is rejected at this level. For example, 20% means that 1 out of 5 new calls are rejected at this level. Value: 0 to 100 percent Default: 50 percent |
*.Ovl3AbateThresh |
Controls engine overload levels. This setting depends on the specified percentage of CPU utilization. If the Ovl3OnsetThreshold is reached, raising an alarm, the Ovl3RejectPercent action abates until this threshold value is reached, clearing the alarm. Value: 0 to 100 percent Default: 85 Note This value must be less than Ovl3OnsetThresh. |
*.Ovl3OnsetThresh |
Controls engine overload levels. This setting depends on the percentage of CPU utilization. If this threshold value is met, an alarm is raised and calls are rejected at the percentage defined by Ovl3RejectPercent. Value: 0 to 100 percent Default: 93 |
*.Ovl3RejectPercent |
Controls engine overload levels. This setting depends on the specified percentage of CPU utilization. A percentage of new calls is rejected at this level. For example, 20% means that 1 out of 5 new calls are rejected at this level. Value: 0 to 100 percent Default: 100 percent |
*.OwnClli |
Common language location identifier; used for circuit query validation when circuit queries are supported. Value: Alphanumeric string, up to 11 characters. Default: TTTT-SS-BB-XXX Example: 1111-22-33-444 |
*.ownTranspathId |
Identifies the local Cisco MGC host in a redundant configuration (same value as *.transpathID). The IDs must be unique in an active and standby pair. Value: Any integer up to 2 digits. Default (for the active Cisco MGC host): 01 Note If you have two Cisco MGC hosts in a failover configuration, enter this value in the *.peerTranspathID field in the XECfgParm.dat file on the second host server. |
*.peerTranspathId |
Identifies the peer Cisco MGC host in a redundant configuration. The IDs must be unique in an active and standby pair. Value: Any integer up to 2 digits. Default (for the standby Cisco MGC host): 02 Note If you have two Cisco MGC hosts in a failover configuration, enter the *.ownTransPathID value from the XECfgParm.dat file of the second host server in this field. If you have a standalone configuration, leave it blank. |
*.platformId |
Enables the signaling controller to run more than one instance of the Cisco MGC software concurrently. Default: 1 Note Do not change this value. |
processes.dat |
Warning Do not modify the processes.dat file. This file should remain unmodified, as delivered with the Cisco MGC software. If this file is modified, procM may core dump when you start the MGC software. Contains information about all processes on the system that the Cisco MGC is responsible for monitoring. There are three different monitoring levels: –Active Process—identified in the record that is controlled and monitored directly by the Process Manager. –Passive Process—identified in the record that does not communicate with the Process Manager. –Monitoring Process—periodically runs an executable or script and sets or clears an alarm based on the return code. This type of process may monitor other processes or tasks that can be checked programmatically, such as the amount of disk space, system daemon existence, and established process dependency. Additionally, this file contains information related to the frequency that the health of each process is checked and how to restart it. |
*.RedirectingATree |
Used to control A-number screening/analysis via A-digit tree. This parameter allows the analysis system to use the A-Digit tree for mapping to the BLACKLIST function on the Redirecting CLI value. It uses the A-Digit tree to allow for black screening on the redirecting number parameter included in the IAM. Currently, when the parameter MDLANumberScreening is set to 1 in the XECfgParm.dat file, screening is done on the redirecting number. This works when screening individual numbers but does not allow block ranges to be screened, as is the case when using DialPlan Screening in the Digit Tree functions. Use an editor such as vi to manually add the *.RedirectingATree parameter to the XECfgParm.dat file in the following file locations and set its value: /opt/CiscoMGC/etc/XECfgParm.dat /opt/CiscoMGC/etc/CONFIG_LIB/new/XECfgParm.dat Valid values: 0 = Default; indicates the Calling Party Number (CGPN) that will be used for A-number screening/analysis via A-digit tree. 1 = Indicates that the Redirecting Number should be used for A-number screening/analysis via A-digit tree if the incoming signaling message contains both the CPN and Redirecting Number or just the Redirecting Number.
Note This property is only effective when BLACKLIST is provisioned. If Screening is data filled and this property is set to 1, then Redirecting Number is used for screening. However, if result types other than BLACKLIST/SCREENING are encountered when Redirecting Number is used during A-number Tree Analysis, an alarm RedirectingNbrFail (informational alarm) is generated.
|
*.runAsDaemon |
Enables processes to run in the background. Default: False •logger.runAsDaemon = false •procM.runAsDaemon = true (runs in the background) •MML.runAsDaemon = false Note Do not change the default values for these settings or the system might not operate correctly. For Release 7.4(7) and later, logger.runAsDaemon should be false. For earlier releases, this should be true. |
*.SelectTermCustGrpId |
This boolean parameter applies only to Nailed Solutions. If this parameter is not defined, it defaults to False. If SelectTermCustGrpId is set to True and CUSTGRPID of the Originating Leg SigPath is 0000, then you must select CUSTGRPID of the Terminating Leg SigPath. If SelectTermCustGrpId is set to False, you should always select CUSTGRPID of the Originating Leg SigPath. Default: False |
*.sm_meas_baseaddr |
Indicates the memory size of the base address. Default: 2048 Note Do not change this value. |
*.stPort |
Port number used between peer components or processes. Enter any unused port number, for example, 7000. If your configuration uses a Cisco SLT, enter the port number on the Cisco SLT. Note If you have two Cisco MGC hosts in a failover configuration, enter a different number for this value in the XECfgParm.dat file on the secondary host, for example, 7001. |
*.SyscheckpointEnabled |
Enables or disables checkpointing. Values: •false = Disables checkpointing. Calls are not preserved during a switchover, and status messages are not sent to the replicator. •true = Enables checkpointing. Calls that are in the talking state are preserved and survive a control switchover. All status checkpointing information is sent to the replicator on the active side. Default: false Note If you have two Cisco MGC hosts in a failover configuration, enter true. If you have a standalone configuration, enter false. |
*.tablesFile |
Location of the database directories. Default: ../etc/tables.dat Note Do not change this value. |
*.tempDir |
Location of the temporary files. Default: /tmp Note Do not change this value. |
*.transpathId |
Identifies the local Cisco MGC host in a redundant configuration. The IDs must be unique in an active and standby pair. Value: Any integer up to 2 digits. Default (for the active host): 01 Note If you have two Cisco MGC hosts in a failover configuration, this number must be different in the XECfgParm.dat file for each host. |
*.VSCNetworkPlacement |
Determines Cisco MGC placement (AT or IXC) and bias routing accordingly. Values: •Nanp_AT •Nanp_IXC •NULL •0 Default: NULL Note If you do not set this property, all calls will route according to called number or some other criteria, not Carrier ID. |
cfgM.recovDbFile |
Storage location of the configuration manager recovery information. Default: ../var/cfgMRecovery Note Do not change this value. |
diskmonitor.Limit |
Number of days to preserve before disk trimming is initiated. Default: 7 Note Do not change this value. |
diskmonitor.OptFileSys |
List of optional file systems to monitor. Default: (blank) |
diskmonitor.SoftLimit |
Works with diskmonitor.Threshold to prevent the disk from filling up and stopping the Cisco MGC. If true, an override of the preserve limit is allowed. Values: •true •false Default: false Note Do not change this value. |
diskmonitor.Threshold |
Erases old log files to free disk space. The threshold is the percent the disk is full before trimming starts. Value: Any integer from 1 to 100 (% of threshold). Default: 80 |
diskmonitor.CdrRmFinished |
Controls removal of CDRs that have been processed. This parameter controls whether files should be deleted immediately (the default) or kept for X days. This parameter is valid only when a BAM system is pulling CDR files and renaming them".finished" upon successful transfer. Value: 0 (default - delete immediately), or non-zero integer indicated days to delay before being deleted Default: 0 |
cdrDmpr.callDetail |
Specifies that call detail record (CDR) files may be automatically converted from binary format to ASCII, comma-delimited format. Default: /opt/CiscoMGC/local/cdbscript.sh Optional: /opt/CiscoMGC/bin/converter (if binary CDR files need to be converted to ASCII) For maximum performance, change this value to none, as follows: cdrDmpr.callDetail = # Note The default CDR file format has changed from an ASCII format in Release 4 to a binary format in Release 7. The ASCII file has a .csv extension. For more information on generating and viewing CDR files, see the Cisco Media Gateway Controller Software Release 7 Operations, Maintenance, and Troubleshooting Guide. |
dmpr.openCDR |
Specifies whether the standard data dumper should write out CDR files. Values: •true = Standard data dumper opens a CDR file and log the call data blocks (CDB). •false = Standard data dumper does not open a CDR file and does not log CDBs. Default: true Note The default format for CDR files has been changed since release 4 from an ASCII format to a binary format. Use the dmpr.callDetail parameter to convert the files to an ASCII format, if necessary. |
engine.AuditOverloadLvl |
Specifies a queue level where audit processing is deferred to reduce the load on the system. When the queue capacity is at this level or higher, auditing is not canceled, but it is deferred until the queue capacity returns to below this level. Values: 0 to 100 percent •0 = auditing is disabled, regardless of the system load. •100 = auditing is enabled, regardless of the system load. Default: 25 percent Note This is a platform-specific value and depends on your system installation. No auditing is available for nailed trunks. |
engine.AuditTimerInterval |
Time interval in milliseconds between two batches of audits. Value: Any positive integer. Default: 500 Note This is a platform-specific value and depends on your system installation. No auditing is available for nailed trunks. |
engine.CALL_MEM_BLOCK_SIZE |
Block of memory allocated per call; used by MDL. Value: Integer Default: 90000 |
engine.CALL_MEM_CHUNK_SIZE |
Memory chunks allocated from the block of memory designated with engine.CALL_MEM_BLOCK_SIZE. Value: Integer Default: 90000 |
engine.CDRencodingFormat |
Specifies the call detail record (CDR) file encoding format. Values: •AnsiCDB = North American •ItuCDB = European •CustCDB = Custom Default: AnsiCDB |
engine.CDRmessageTypes |
Specifies which call detail blocks (CDBs) are recorded during a call. Default: "1010, 1020, 1030, 1040, 1050, 1060, 1070" Example: "1060, 1110" Each number represents a point in a call. 1060 is required. 1080 is an external value, used for TCAP. Note If you choose 1110, you must specify milliseconds for the CDRtimeStamp parameter.
Refer to the the chapter "Detailed CDB Description" in the Cisco Media Gateway Controller Software Release 7 Billing Interface Guide for information on CDE tags contained in each CDB. |
engine.CDRtimeStamp |
Specifies the time stamp unit in seconds or milliseconds. If a BAM is being used for billing and measurements, the value must be "M". Values: •S = seconds (Default) •M = milliseconds |
engine.CMMdlFile |
Location of call processing libraries. Default: ../lib/cc Note Do not change this value. |
engine.LCMMdlFile |
Location of call processing libraries. Default: ../lib/lcm Note Do not change this value. |
engine.MaxAuditCics |
Number of circuit identification codes (CICs) that can be audited at a specified interval. Values: •24 = North America (T1) •32 = Europe (E1) Default: 32 Note Do not change this value. |
engine.mdoDir |
Location of call processing libraries. Default: ../lib/ Note Do not change this value. |
engine.SysCdrCollection |
Designates the format of call detail records (CDRs). Values: •true = Invalid for Release 7.4 and above. •false = generates binary format CDRs (default) Default: false Note Do not change this value. Setting this to a value of true for Release 7.4 and above is not valid and may have deleterious effects on the system. |
engine.SysCLIval |
Enables or disables Calling Line Identity (CLI) validation processing on calls. Values: •true = enables CLI validation •false = disables CLI validation Default: false |
engine.SysGeneratedCode |
Determines whether compiled or interpreted code is used. Values: •true = system uses compiled code •false = system uses interpreted code Default: true Note Compiled code runs faster than interpreted code. Typically, this value should be true. If your configuration uses multiple CPUs, this value must be true. |
engine.SysGRSBlockSize |
Specifies the number of simultaneous Circuit Group Reset (GRS) messages to send in each block, based on the timing interval set in the engine.SysGRSTimerInterval parameter. This parameter operates independently for each SS7 route (each OPC/DPC pair). Value: Any integer Default: 0 Example: 1 |
engine.SysGRSTimerInterval |
Specifies the interval, in milliseconds, between blocks of GRS parameters when the engine.SysGRSBlockSize parameter is used. The timer interval runs from the start of sending the first GRS message in each block to the first message in the next block. Value: Any integer. Default: 0 Example: 1000 |
engine.SysGSMTimerInterval |
Allows group service messages (GSMs—used to advertise the state of circuits) to be sent at a periodic rate from the SS7 side of the network to the IP side of the network. Valid values: 1000 to 15000 Default: 15000 |
engine.SysMaxOverlap |
Maximum number of digits required before a call is considered complete; used in overlap signaling. Default: 28 Note Do not change this value. |
engine.SysMdlMemoryReduction |
Controls use of MDL memory reductions. Values: •0 = MDL memory reductions not used (maximum performance) •1 = MDL memory reduction improvements used Default: 0 Note For performance-critical configurations, use the default value. For memory-critical configurations, set this value to 1. |
engine.SysMinOverlap |
Minimum number of digits required before a call is considered valid; used in overlap signaling. Default: 0 Note Do not change this value. |
engine.SysPropagateChanAvail |
In a classic signaling controller configuration, propagates service messages between channels in the event of a channel failure. Values: •true = messages propagated •false = messages not propagated (default) Note Do not change this value. |
engine.SysScreeningCheck |
Enables or disables the call screening database. If you do not have the database environment set with all of the required data populated, set this value to false. Set this value to true if you have the database and want the system to access it. Values: •true = enabled •false = disabled Default: false
Note Setting this parameter to true will impact system performance because it will reduce MAX CPS and the maximum number of sustained calls.
|
engine.SysSGCPRetryCount |
Maximum number of simple gateway control protocol (SGCP) retry messages after a failure. Default: 3 Note Do not change this value. |
engine.SysSGCPREtryTimerInterval |
The interval between SGCP message transmissions, in milliseconds. Default: 1000 Note Do not change this value. |
engine.SysTraceLevel |
A debugging tool that allows for different levels of engine tracing. Default: 3 Note Do not change this value. |
engine.SysVirtualSwitch |
Indicates whether the Cisco MGC host functions as a signaling controller or a virtual switch controller. Values: •0 = signaling controller (nailed trunks, no auditing is initiated) •1 = virtual switch controller (switched trunks) Default: 0 |
engine.VersionTimeoutValue |
Defines the timeout interval in number of milliseconds for version messages sent to the MGW. This delay determines how long the Cisco MGC will wait for response from the MGW during the exchange of features prior to the audit. Value: Any integer. Default: 10000 |
foverd.abswitchPort |
Port used for communication with the A/B switch. Value: /dev/term/x Example: /dev/term/b Note If your configuration does not use an A/B switch, use the default value (/dev/null). |
foverd.abswitchTestInterval |
Time interval in milliseconds between attempts to verify that an A/B switch is present. Default: 30000 Note This parameter only applies if your configuration uses an A/B switch. |
foverd.ackTimeout |
Maximum time, in milliseconds, that the failover daemon will wait for an ACK or NOACK message to be received from the peer failover daemon. For each message the failover daemon sends, the peer failover daemon sends an ACK or NOACK message to indicate that the peer is still functioning. Default: 1000 milliseconds (1 second). Note You can change the default value to a value more appropriate for your system installation. |
foverd.commRetryInterval |
Time interval in milliseconds between attempts to open a connection. Connection types include: •Connection to the peer failover daemon •Connection to the A/B switch •Connection to the ARU Default: 30000 milliseconds (30 seconds). Note You can change the default value to a value more suited to your system installation. |
foverd.conn1Type |
Sets the connection type for connection number 1. Values: •serial •socket Note Typically, set this value to socket. |
foverd.conn2Type |
Sets the connection type for connection number 2. Values: •serial •socket Note Typically, set this value to socket. |
foverd.conn3Addr |
Specifies the address of the peer system. Example: /dev/term/b If your configuration does not use connection number 3, enter /dev/null (default). Note If your configuration uses an 8-port connector as a serial connection for failover, you must modify the read-write permissions for the connection. For more information, see the Release Notes for the Cisco Media Gateway Controller Software Release 7. |
foverd.conn3Type |
Sets the connection type for connection number 3. Values: •serial •socket Note Typically, set this value to serial. |
foverd.delayTimeout |
Maximum time in milliseconds that the failover daemon can delay at startup before sending messages to its peer. This is also the delay offset that is added when the two failover daemons become too closely synchronized. Default: 1000 milliseconds (1 second) |
foverd.forceShutTimeout |
Maximum time in milliseconds that the failover daemon waits before forcefully shutting down the platform. Default: 1000 milliseconds (1 second) |
foverd.graceShutTimeout |
Maximum time in milliseconds that the failover daemon waits before gracefully shutting down the process manager, which shuts down the processes it controls. Default: 6000 milliseconds (6 seconds) |
foverd.heartbeatInterval |
Maximum time in milliseconds between heartbeat messages from the peer failover daemon. This interval defines the frequency that the failover daemon exchanges heartbeat messages with its peer. Default: 4000 milliseconds (4 seconds). |
foverd.ipLocalPortA |
Port number used for IP communication. Default: 0 Note If you have two Cisco MGC hosts in a failover configuration, enter this value for the foverd.ipPeerPortA field in the XECfgParm.dat file on the secondary host. |
foverd.ipLocalPortB |
Port number used for IP communication. Default: 0 Note If you have two Cisco MGC hosts in a failover configuration, enter this value for the foverd.ipPeerPortB field in the XECfgParm.dat file on the secondary host. |
foverd.ipPeerPortA |
Port number used for IP communication. Default: 0 Note If you have two Cisco MGC hosts in a failover configuration, enter this value for the foverd.ipLocalPortA field in the XECfgParm.dat file on the secondary host. |
foverd.ipPeerPortB |
Port number used for IP communication. Default: 0 Note If you have two Cisco MGC hosts in a failover configuration, enter this value for the foverd.ipLocalPortB field in the XECfgParm.dat file on the secondary host. |
foverd.peerCommTimeout |
Maximum time in milliseconds without communication with the remote system. At the expiration of this period, the remote system is assumed to be unavailable and failover is triggered automatically. Default: 10000 milliseconds (10 seconds) Note A timeout value that is too small can cause a false failover, resulting in possible service interruptions. |
foverd.statusRptInterval |
Time interval in milliseconds that governs the frequency with which the failover daemon logs statistics on the different connections and any failures it encountered exchanging messages with its peer. Logs are created in the log directory. Default: 600000 milliseconds (10 minutes) |
foverd.transitionTimeout |
Maximum time in milliseconds allowed for transitions between different states of the failover daemon. This timeout determines how long the system waits for a graceful transition to a new state before forcing the transition. If a timeout occurs, the system is restarted. Default: 10000 milliseconds (10 seconds). |
ioChanCtl.DPNSSTestFrames |
Enables DPNSS to generate test frames. Values: •true = if DPNSS is running, test frames are generated •false = test frames are not generated Default: true Note Do not change this value. |
ioChanMgr.alarmTimer |
This parameter is obsolete and should be set to 0. |
ioChanMgr.evtTimer |
Frequency, in milliseconds, at which the queue is scanned for messages. Default: 100 Note Do not change this value. |
ioChanMgr.hbTimer |
This parameter is reserved for future use. |
ioChanMgr.resumeAckTimer |
Amount of time VSC waits to get a MGMT_RESUME_ACK_RSP message from a gateway, after sending a MGMT_RESUME_REQ message fro a BSM session set. Values are 1 to 2 seconds. Default: 1 |
ioChanMgr.sendThreshold |
Maximum number of events sent from the queue at one time. Default: 10 Note Do not change this value. |
ioChanMgr.sessionPauseTimer |
Amount of time VSC waits for a BSM session set to recover from failure before declaring the session set failure. Values are 1 to 10 sec. Default: 8 |
ioChanMgr.statDiscardThreshold |
Size of the control queue that triggers discarding of all queued stat events. Default: 40 Note Do not change this value. |
ioChanMgr.statTimer |
Frequency, in milliseconds, at which measurements are collected in the Transpath input/output system (TIOS). Default: 30000 milliseconds Note Do not change this value. |
ioChanMgr.trace |
Creates unit test tracing of line and channel state machines. Generates a considerable amount of information to the log. Set to a value only when you are debugging a particular problem with line or channel service state problems. Values: •0 x 0 = default •0 x 1 = trace Note Do not change this value. |
logger.daemonAddr |
Specifies the name of the local socket used by the log server daemon. The daemon listens for connections on this address, and client programs attempt to connect to the daemon at this address. Default: ../var/log/lsd_addr Note If this setting is missing from the XECfgParm.dat file, the log server daemon does not run. |
logger.fileRotateInterval |
Triggers a file rotation based on the time elapsed since the previous rotation. Default: 1440 minutes (24 hours) Note This timer is reset after any rotation occurs, regardless of the cause or trigger of the rotation. |
logger.fileRotateSize |
Triggers a file rotation based on the size of the active file. A file rotation triggered by this parameter also resets the logger.fileRotateInterval timer. Default: 100MB Note The file size may grow somewhat larger than this parameter indicates due to the verbosity of the logging levels currently in effect. |
logger.numThreads |
Determines whether the PXE logger should run in a separate thread from the rest of the application. A value of 0 runs the logger synchronously with the application; a value of 1 runs the logger in a separate thread. Value: 0/1 (Values less than 0 get reset to 0; values greater than 1 get reset to 1.) Default: 0 |
MML.chg-cfg |
Timeout value for the chg-cfg MML command in milliseconds; overrides MML.timeout. Default: 10000 milliseconds Note Do not change this value. This MML command is obsolete. |
MML.set-sc-state |
Timeout value for the set-sc-state MML command in milliseconds; overrides MML.timeout. Default: 8500 milliseconds Note Do not change this value. |
MML.snd |
Timeout value for the snd MML command in milliseconds; overrides MML.timeout. Default: 600000 milliseconds Note Do not change this value. |
MML.startPM |
Timeout value for the startPM MML command in milliseconds; overrides MML.timeout. Default: /etc/init.d/CiscoMGC start Note Do not change this value. |
MML.stopPM |
Timeout value for the stopPM MML command in milliseconds; overrides MML.timeout. Default: /etc/init.d/CiscoMGC stop Note Do not change this value. |
MML.timeout |
Timeout for MML commands, in milliseconds. Default: 10000 milliseconds Note Do not change this value. |
MML.vld-cic |
Timeout value for the vld-cic MML command in milliseconds; overrides MML.timeout. Default: 25000 milliseconds Note Do not change this value. |
pom.dataSync |
Indicates that the Provisioning Object Manager (POM) should synchronize the provisioning data at startup. Values: •true = POM is enabled, data is synchronized •false = POM is disabled, no data synchronization (default) Note If you have two Cisco MGC hosts in a failover configuration, set this value to true. If you have a standalone Cisco MGC, set this value to false. |
pom.port |
In a failover configuration, indicates the port number the POM uses to communicate with its peer. Value: Any integer from 4001 to 4050 Default: 4001 or default Note This is a platform-specific value and depends on your system installation. You should only modify this value if the default port (4001) is being used by another process or application. |
procM.almDwellInterval |
Seconds that the process manager must wait before clearing an alarm. Default: 15 seconds Note Do not change this value. |
procM.logDBFile |
Specifies the location of the log level storage. Default: ../var/procMLogTable |
procM.minCheckHealthInterval |
Seconds at which a process can generate heartbeats. Default: 10 seconds Note Do not change this value. |
procM.minCheckHealthTimeout |
Seconds at which a timeout can occur. Default: 2 seconds Note Do not change this value. |
procM.minKillGracePeriod |
Seconds that the process manager must wait before killing a process after a heartbeat timeout. Default: 5 seconds Note Do not change this value. |
procM.recovDbFile |
Storage location of the process manager persistent information. Default: ../var/procMRecovery Note Do not change this value. |
procM.servFmt |
Format of the process manager temporary files. Default: PM_%d_%d_input Note Do not change this value. |
procM.servicesDir |
Location of the process manager temporary files. Default: ../var Note Do not change this value. |
procMprocHealthDfltAlmCat |
This parameter is no longer used. |
product.time |
Software time stamp. Note Do not change this value. |
product.vendor |
Software vendor name. Note Do not change this value. |
product.version |
Software release version number. Note Do not change this value. |
replicator.portCommChannelRecv |
Communication port for the replicator. Default: 2974 Note Do not change this value. |
replicator.portCommChannelSend |
Communication port for the replicator. Default: 2972 Note Do not change this value. |
replicator.portDataChannelRecv |
Communication port for the replicator. Default: 2970 Note Do not change this value. |
replicator.portDataChannelSend |
Communication port for the replicator. Default: 2968 Note Do not change this value. |
replicator.reconnectInterval |
Defines the reconnect interval in number of seconds for the replicator during a switchover. Value: Any integer Default: 15 seconds Note Set this value to 0 for a standalone Cisco MGC. |
XE.ARUWriteDevice |
Name of the device from which the alarm relay unit (ARU) expects to read the alarm strings. Example: /dev/null Note This setting is required if your configuration does not use an ARU. If you do not set this device, the system uses # /dev/tty. Do not change this value unless your configuration uses an ARU. |
XE.heartBeatRate |
Heartbeat rate, in seconds, used with an alarm relay unit (ARU). Default: 60 seconds Note Do not change this value unless your configuration uses an ARU. |
XE.systemType |
Indicates the system type for alarm LEDs. Values: •NETRA-FT = Sun Netra ft 1800 •NETRA = Sun Netra t 1100, t 1120 (internal LEDs, alarm relays) •SPARC = Generic box (no alarm relays) •SPARC-ARU = Generic box (external alarm relays) Default: SPARC |
Feedback