Chapter 1. Introduction

This guide explains each xml tag used in the configuration file (.xml) of Cisco IP DECT 6800 Series . Each tag represents a parameter in the phone.

Each xml tag definition includes details such as command syntax, default value, and description.

- New and Changed Information

New and Changed Information

Revision History

Release

What's New and Updated

Firmware Release 5.1(2)

Cfg_Rep_OnChange

Cfg_Rep_Period

Firewall

Firewall_Config

Firmware Release 5.1(1)

PRT_http_header

PRT_http_header_value

PRT_upload_filename

PRT_upload_server

Hebu_Mode

Subscr_Hebu_Password_n_

Subscr_Hebu_Username_n_

Language_Rule

Held_Company_Id

Held_Token_Srvn

Reg_Retry_Intvl_High_Rnd

Reg_Retry_Long_Intvl_High_Rnd

Srv_Failback_Before_Failover_n_

Hs_Admin_Pin_n_

Hs_Alarm_Enable_n_

Hs_Alarm_n_

Hs_Alert_Tone_n_

Hs_Alert_Vol_n_

Hs_Auto_Answer_n_

Hs_Auto_Keylock_n_

Hs_Bluetooth_n_

Hs_Charger_Warn_n_

Hs_Config_Protocol

Hs_Config_Server

Hs_Config_Server_Password

Hs_Config_Server_Username

Hs_Confirm_Sound_n_

Hs_Coverage_Warn_n_

Hs_Hide_Number_n_

Hs_Idle_Clock_n_

Hs_Idle_Screen_n_

Hs_Key_Sound_n_

Hs_Led_Green_n_

Hs_Led_Orange_n_

Hs_Led_Red_n_

Hs_Line_n_

Hs_Msg_Display_n_

Hs_Msg_Overwrite_Old_n_

Hs_Msg_Send_n_

Hs_Name_n_

Hs_Phone_Lock_n_

Hs_Power_Save_n_

Hs_Ptt_n_

Hs_Rec_Alarm_Enable_n_

Hs_Rec_Alarm_n_

Hs_Ring_Emerg_High_n_

Hs_Ring_Emerg_Low_n_

Hs_Ring_Emerg_Mid_n_

Hs_Ring_Mel_n_

Hs_Ring_Norm_Msg_n_

Hs_Ring_Urgent_Msg_n_

Hs_Ring_Vol_n_

Hs_Select_Network_n_

Hs_Silent_Charging_n_

Hs_Silent_n_

Hs_Unlock_Pin_n_

Hs_Vibrate_n_

Call_Id_Map_n_

Call_Id_Map_Subscription_n_

Call_group_SIP_account_n_

Subcsr_Call_Group_Subscribed_

Subscr_Intercom_Enabled_

Firmware Release 5.0(1)

Introduced the document for Cisco IP DECT 6800 Series XML parameters running SIP Firmware Release 5.0(1) with Cisco BroadWorks version 22 and later.

Chapter 2. XML Tags for Base Station Settings

This section provides information about XML tags used for base station settings.

- Admin_Password

- Allow_Call_Groups

- Auth_ID_n_

- Auth_Resync_reboot_n_

- Auto_Dect_Register

- Auto_Resync_Days

- AVT_Dynamic_Payload_n_

- BLF_List_URI_n_

- Blind_Transfer_Code

- Blind_Transfer_Serv_n_

- Block_ANC_Act_Code

- Block_ANC_Deact_Code

- Block_ANS_Setting

- Block_CID_Act_Code

- Block_CID_Deact_Code

- Busy_Tone

- Call_Return_Code

- Call_Waiting_Tone

- Caller_ID_Header

- Call_group_SIP_account_n_

- Call_Id_Map_n_

- Call_Id_Map_Subscription_n_

- Call_Statistics_In_SIP_n_

- CDP

- CDP_Delay

- Certificate_use_only_trusted

- Cfg_Rep_OnChange

- Cfg_Rep_Period

- Cfwd_All_Act_Code

- Cfwd_All_Deact_Code

- Cfwd_All_Dest_n_

- Cfwd_All_Serv_n_

- Cfwd_Busy_Dest_n_

- Cfwd_Busy_Serv_n_

- Cfwd_No_Ans_Delay_n

- Cfwd_No_Ans_Dest_n_

- Cfwd_No_Ans_Serv_n_

- Conference_Bridge_URL_n_

- Conference_Serv_n_

- Conference_Tone

- ConfigurationDownloadCtrl

- Confirm_Tone

- Connection_Type

- Country_Region_ID

- Country_Variant_ID

- CW_Act_Code

- CW_Deact_Code

- CW_Setting_n_

- Daylight_Saving_Time_By_Country_Region

- Daylight_Saving_Time_Enable

- Daylight_Saving_Time_Rule

- Debug_Level

- DHCP_Option_To_Use

- Dial_Plan_n_

- Dial_Plan_Subscription_n_

- Directory_Enable

- Directory_Enterprise_Common_Enable

- Directory_Enterprise_Common_Name

- Directory_Enterprise_Name

- Directory_Enterprise_Enable

- Directory_Group_Common_Enable

- Directory_Group_Common_Name

- Directory_Group_Name

- Directory_Group_Name_Enable

- Directory_Personal_Name

- Directory_Personal_Name_Enable

- Display_Name_n_

- DND_Act_Code

- DND_Deact_Code

- DTMF_Tx_Method_n_

- Dual_Cell_Replacement_Timeout

- Emergency_Alarm_Block_Time

- Emergency_Alarm_Howling_n_

- Emergency_Alarm_Number_n_

- Emergency_Alarm_Priority_n_

- Emergency_Alarm_Signal_n_

- Emergency_Alarm_Stop_Allowed_n_

- Emergency_Alarm_Type_n_

- Emergency_Number_n_

- Emergency_Pre_Alarm_Delay_n_

- Emergency_Pre_Alarm_Stop_Allowed_n_

- Emergency_Profile_Alias_n_

- Emergency_Trigger_Delay_n_

- Enable_Protocol

- Enable_Web_Server

- Encryption_Method_n_

- Feature_Key_Sync_n_

- FilenameMultiSpecific

- Firewall

- Firewall_Config

- Gateway

- Group_Paging_Script_n_

- Handle_VIA_received_n_

- Handset_Alarm_Auto_Stop_Allowed

- Handset_Alarm_Auto_Stop_Delay

- Handset_Keepalive_Delay

- Hs_Alarm_Enable_n_

- Hs_Config_Protocol

- Hs_Config_Server

- Hs_Config_Server_Password

- Hs_Config_Server_Username

- Hebu_Mode

- Held_Company_Id

- Held_Token_Srvn

- Holding_Tone

- Insert_VIA_rport

- Ieee1588_Enabled

- Ieee1588_Zone_Multicast_Alt_Domain

- Ieee1588_Zone_Multicast_Domain

- Ieee1588_Zone_Multicast_Ip

- Ieee1588_Zone_Multicast_Port

- INVITE_Expires

- Language_Rule

- Language_Selection

- LDAP_Username

- LDAP_Dir_Enable

- LDAP_Display_Attrs

- LDAP_First_Name_Filter

- LDAP_Last_Name_Filter

- LDAP_Password

- LDAP_Search_Base

- LDAP_Server

- Ldap_Virtual_Lists

- Line_Enable_n_

- Line_Name_n_

- LLDP

- LLDP_Delay

- Login_Password

- Login_User_ID

- Mailbox_ID_n_

- Management_Factory_Reset_From_Button

- MDNS_Support

- MediasSec_Over_TLS_Only_n_

- MediaSec_Request_n_

- NAT_Keep_Alive_Intvl

- NetMask

- Network_Allow_Multi_Primary

- Network_Auto_Multi_Primary

- Network_Data_Config_Primary_Mac

- Network_Dect_Auto_Sync_Tree_Config

- Network_Roaming_Deregister

- Network_Sntp_Broadcast_Enable

- Network_Sync_Chain_Id

- Network_Sync_Data_Transport

- Network_Sync_Debug_Enable

- Network_Sync_Enable

- Network_Sync_Max_Sip_Reg_Per_Base

- Network_Sync_Primary_Static_Ip

- Network_Sync_Time

- Network_Vlan_Synchronization

- Network_Wan_Dhcp_Option_Plug_And_Play

- Number_Of_Base_Stations

- Off_Hook_Warning_Tone

- Outbound_Proxy_n_

- Page_Tone

- Password_n_

- Phone_Name

- Phonebook_Filename

- Phonebook_Location

- Phonebook_Reload_Time

- Phonebook_Server_Location

- Pnp_Config

- Preferred_Codec_n_

- Primary_DNS

- Primary_NTP_Server

- Profile_Rule

- Promiscuous_button_enabled

- Promiscuous_mode

- Prompt_Tone

- Proxy_n_

- PRT_http_header

- PRT_http_header_value

- PRT_upload_filename

- PRT_upload_server

- Reg_Retry_Intvl_n_

- Reg_Retry_Intvl_High_Rnd

- Reg_Retry_Long_Intvl_n_

- Reg_Retry_Long_Intvl_High_Rnd

- Register_Expires_n_

- Reorder_Tone

- Repeater_Auto_Config_Mode_n_

- Repeater_Data_Configured_n_

- Repeater_Dect_Ipui_n_

- Repeater_Name_n_

- Repeater_Rpn_n_

- Repeater_Sync_Src_Rpn_n_

- Resync_At_HHmm_

- Resync_At_Random_Delay

- Resync_Periodic

- Resync_Polling

- Retry_Reg_RSC_n_

- Reversed_Auth_Realm_n_

- Reverse_Phone_Lookup_Serv

- RFC_2543_Call_Hold_n_

- Ring_Back_Tone

- Rsx_Trace_Internal

- Rtp_Collision_Control

- RTP_Packet_Size_n_

- RTP_Port_Max

- RTP_Port_Min

- RTP_TOS_DiffServ_Value

- Second_Preferred_Codec_n_

- Secondary_DNS

- Secure_Call_Option_n_

- Secure_Call_Setting_n_

- Server_ID_n_

- Share_Call_Appearance_n_

- SIP_100REL_Enable_n_

- Sip_Check_Sync_Always_Reboot

- Sip_Failover_Reconnect_Timer

- SIP_Outbound_Proxy_Mode

- SIP_Port

- Sip_Reject_Anonymous_Calls_Enabled_n

- Sip_Stun_Bindtime_Determine

- Sip_Stun_Bindtime_Guard

- Sip_Timer_B

- Sip_Timer_F

- SIP_TOS_DiffServ_value

- SIP_Transport_n_

- Sip_Use_Different_Ports

- Src_Att_Transfer_2nd_call_On_Hold_1_

- Srv_Codec_Enable_G729ab_n_

- Srv_Enable_No_Sip_Registration_n_

- Srv_Failback_Before_Failover_n_

- Srv_Failback_de_register_n_

- Srv_Remote_Ringtone_n_

- Srv_Sip_Enable_Ptime_n_

- Srv_Sip_Enable_Rtcp_n_

- Srv_Sip_Keep_Alive_n_

- Srv_Sip_Ringback_Tone_n_

- Srv_Sip_Rtp_Base_Equal_n_

- Srv_Sip_Server_Alias_n_

- Srv_Sip_Show_Ext_Name_In_Hs_n_

- Srv_Sip_Signal_Tcp_Port_n_

- Srv_SRTP_Auth_n_

- Static_IP

- STUN_Enable

- STUN_Server

- Subcsr_Call_Group_Subscribed_

- Subscr_Dect_Ac_Code_n_

- Subscr_Dect_Ipui_n_

- Subscr_Do_Not_Disturb_Enabled_n_

- Subscr_Hebu_Password_n_

- Subscr_Hebu_Username_n_

- Subscr_Hide_Number_Enabled_n_

- Subscr_Intercom_Enabled_

- Subscr_Sip_Hs_Idx_n_

- Subscr_Sip_Pincode_Dialout_n_

- Subscr_Sip_Reject_Anonymous_Calls_Enabled_n_

- Subscr_Sip_Ua_Use_Base_n_

- Subscr_Ua_Data_Bw_Sca_Info_Mapping_n_

- Subscr_Ua_Data_Emergency_Line_n_

- Subscr_Ua_Data_Emergency_Profiles_n_

- Syslog_Server

- Syslog_Transport

- Tcp_Keep_Alive_Interval

- Text_Msg_Keep_Alive

- Text_Msg_Mode

- Text_Msg_Port

- Text_Msg_Response_Time

- Text_Msg_Server

- Text_Msg_Ttl

- Third_Preferred_Codec_n_

- Upgrade Rule (Base Station)

- Upgrade Rule (Handset)

- Upgrade_Rule_RPT (Repeater)

- Use_One_Tcp_Conn_Per_Ext_n_

- Use_Pref_Codec_Only_n_

- User_ID_n_

- User_Password

- VLAN_ID

- Vlan_QoS

- Voice_Mail_Number_n_

- Voip_Sip_Auto_Upload

- Web_Language

- Web_Min_Pass_Len

- Web_Pass_Constraint_To_Ascii

- XSI_Host_Server

Admin_Password

Syntax Description

XML Tag Name

Admin_Password

Example:

<Admin_Password>Testadminpwd1@</Admin_Password>

Web Parameter

Admin Password

Default Value

String up to 8 characters

Allowed Values

String

Units

String

Limits

128 characters

User or Admin

Exposed in admin level

Description

Indicates the administrator password.

Labels

Security

Allow_Call_Groups

Syntax Description

XML Tag Name

Allow_Call_Groups
Example:

<Allow_Call_Groups>On</Allow_Call_Groups>

This parameter is only applicable for 110 Single-Cell Base Station

Web Parameter

None

Default Value

On

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if the local call group is enabled in the base station.

Labels

None

Auth_ID_n_

Syntax Description

XML Tag Name

Auth_ID_n_
Example:

<Auth_ID_1_>1234</Auth_ID_1_>

Web Parameter

Extension

Default Value

None

Allowed Values

String

Units

String

Limits

128 characters

User or Admin

Exposed in admin level

Description

Indicates the SIP username or extension.

Labels

Extensions

Auth_Resync_reboot_n_

Syntax Description

XML Tag Name

Auth_Resync_reboot_n_

Example:

<Auth_Resync_reboot_1_>Enabled</ Auth_Resync_reboot_1_>

Web Parameter

Auth Resync reboot

Default Value

Enabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Enabled—Indicates that the base requests authorization when there is a notification to reset, check-sync, or reboot.

Labels

Servers

Auto_Dect_Register

Syntax Description

XML Tag Name

Auto_Dect_Register
Example:

<Auto_Dect_Register>On</Auto_Dect_Register>

Web Parameter

None

Default Value

No

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Controls whether to enable handset registration.

Labels

None

Auto_Resync_Days

Syntax Description

XML Tag Name

Auto_Resync_Days
Example:

<Auto_Resync_Days>50</Auto_Resync_Days>

Web Parameter

Auto Resync Days

Default Value

1

Allowed Values

Integer

Units

Integer

Limits

0-365 digits

User or Admin

Exposed in admin level

Description

Indicates the number of days between resync operations.

Use this parameter with Auto_Resync_Time, Auto_Resync_Polling, Auto_Resync_Periodic, and Auto_Resync_Delay

Labels

Management

AVT_Dynamic_Payload_n_

Syntax Description

XML Tag Name

AVT_Dynamic_Payload_n_
Example:

<AVT_Dynamic_Payload_1_>115</AVT_Dynamic_Payload_1_>

Web Parameter

DTMF Payload Type

Default Value

101

Allowed Values

Integer

Units

Integer

Limits

0-255 digits

User or Admin

Exposed in admin level

Description

Indicates the type of DTMF payload when the DTMF Signaling field is set to RFC 2833.

Labels

Servers

BLF_List_URI_n_

Syntax Description

XML Tag Name

BLF_List_URI_n_
Example:

<BLF_List_URI_1_>MonitoredUsersList@sipurash22.com</BLF_List_URI_1_>

Web Parameter

None

Default Value

None

Allowed Values

String

Units

String

Limits

9 characters

User or Admin

Exposed in admin level

Description

Indicates the URI for Busy Lamp Field resource list on the BroadWorks application server.

Only 10 characters are allocated for each URI . The server registrar field provides the server information.

Labels

None

Blind_Transfer_Code

Syntax Description

XML Tag Name

Blind_Transfer_Code
Example:

<Blind_Transfer_Code>*90</Blind_Transfer_Code>

Web Parameter

Blind Transfer

Default Value

*88

Allowed Values

Integer

Units

Integer

Limits

0-99 digits

User or Admin

Exposed in admin level

Description

Indicates to dial this star code to transfer a call without consultation.

Labels

Star Codes

Blind_Transfer_Serv_n_

Syntax Description

XML Tag Name

Blind_Transfer_Serv_n_
Example:

<Blind_Transfer_Serv_1_>Enabled</Blind_Transfer_Serv_1_>

Web Parameter

Enable Blind Transfer

Default Value

Disabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if you can transfer without consultation.

Labels

Servers

Block_ANC_Act_Code

Syntax Description

XML Tag Name

Block_ANC_Act_Code
Example:

<Block_ANC_Act_Code>*80</Block_ANC_Act_Code>

Web Parameter

Block Anonymous Incoming Calls Activate

Default Value

*77

Allowed Values

Integer

Units

Integer

Limits

0-99

User or Admin

Exposed in admin level

Description

Indicates to dial this star code to block calls that don't have a caller ID.

Labels

Star Codes

Block_ANC_Deact_Code

Syntax Description

XML Tag Name

Block_ANC_Deact_Code
Example:

<Block_ANC_Deact_Code>*90</Block_ANC_Deact_Code>

Web Parameter

Block Anonymous Incoming Calls Deactivate

Default Value

*87

Allowed Values

Integer

Units

Integer

Limits

0-99

User or Admin

Exposed in admin level

Description

Indicates to dial this star code to all the phones to receive calls that don't have a caller ID.

Labels

Star Codes

Block_ANS_Setting

Syntax Description

XML Tag Name

Block_ANS_Setting
Example:

<Block_ANS_Setting>Yes</Block_ANS_Setting>

Web Parameter

None

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if rejection of anonymous calls is enabled for a given subscription.

Labels

None

Block_CID_Act_Code

Syntax Description

XML Tag Name

Block_CID_Act_Code
Example:

<Block_CID_Act_Code>*75</Block_CID_Act_Code>

Web Parameter

Block Caller Id On Outgoing Calls Activate

Default Value

*67

Allowed Values

Integer

Units

Integer

Limits

0-99

User or Admin

Exposed in admin level

Description

Indicates to dial this star code to not send the caller ID on an outgoing call.

Labels

Star Codes

Block_CID_Deact_Code

Syntax Description

XML Tag Name

Block_CID_Deact_Code
Example:

<Block_CID_Deact_Code>*70</Block_CID_Deact_Code>

Web Parameter

Block Caller ID On Outgoing Calls Deactivate

Default Value

*68

Allowed Values

Integer

Units

Integer

Limits

0-99

User or Admin

Exposed in Admin level

Description

Indicates to dial this star code to send the caller ID on an outgoing call.

Labels

Star Codes

Busy_Tone

Syntax Description

XML Tag Name

Busy_Tone
Example:

<Busy_Tone>480@-19,620@-19;10(.5/.5/1+2)</Busy_Tone>

Web Parameter

Busy Tone

Default Value

480@-19,620@-19;10(.5/.5/1+2)

Allowed Values

String

Units

String

Limits

256 characters

User or Admin

Exposed in admin level

Description

Plays the tone when an outbound call receives 486 RSC.

Labels

Call Progress Tones

Call_Return_Code

Syntax Description

XML Tag Name

Call_Return_Code
Example:

<Call_Return_Code>*75</Call_Return_Code>

Web Parameter

Call Return

Default Value

*69

Allowed Values

Integer

Units

Integer

Limits

0-99

User or Admin

Exposed in admin level

Description

Indicates to dial this star code to return a call.

Labels

Star Codes

Call_Waiting_Tone

Syntax Description

XML Tag Name

Call_Waiting_Tone
Example:

<Call_Waiting_Tone>440@-10;30(.3/9.7/1)</Call_Waiting_Tone>

Web Parameter

Call Waiting Tone

Default Value

440@-10;30(.3/9.7/1)

Allowed Values

String

Units

String

Limits

256 characters

User or Admin

Exposed in admin level

Description

Indicates the tone that plays when a call is waiting.

Labels

Call Progress Tones

Caller_ID_Header

Syntax Description

XML Tag Name

Caller_ID_Header
Example:

<Caller_ID_Header>1</Caller_ID_Header>

Web Parameter

Remove Caller ID Source Priority

Default Value

0 (PAI-FROM)

Allowed Values

- 0: PAI-FROM

- 1: FROM

- 2: ALERT_INFO - PAI -FROM

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Contains SIP information that Caller ID source uses.

Labels

Servers

Call_group_SIP_account_n_

Syntax Description

XML Tag Name

Call_group_SIP_account_n_

Example:

<Call_group_SIP_account_30>1000</Call_group_SIP_account_30>

Web Parameter

Idx

Default Value

1000

Allowed Values

Integer

Units

Integer

Limits

0-999

User or Admin

Exposed in admin/user level

Description

Indicates the 16-bit SIP account times the number of supported call groups.

Labels

Local Call Groups

Call_Id_Map_n_

Syntax Description

XML Tag Name

Call_Id_Map_n_

Example:

<Call_Id_Map_1_>&<25:>xxxx</Call_Id_Map_1_>

Web Parameter

Call Id Map

Default Value

""

Allowed Values

String

Units

String

Limits

64 characters

User or Admin

Exposed in admin/user level

Description

Defines the caller ID to match the number in the contacts list.

Labels

Dial Plans

Call_Id_Map_Subscription_n_

Syntax Description

XML Tag Name

Call_Id_Map_Subscription_n_

Where, n is the handset extension index.

Example:

<Call_Id_Map_Subscription_1_>2</Call_Id_Map_Subscription_1_>

Web Parameter

Caller ID Map

Default Value

1

Allowed Values

1-10

Units

Digit

Limits

1 to 10

User or Admin

Exposed in admin/user level

Description

Defines the caller ID index for the handset extension.

Labels

Extensions > Terminal

Call_Statistics_In_SIP_n_

Syntax Description

XML Tag Name

Call_Statistics_In_SIP_n_

Example:

<Call_Statistics_In_SIP_1>Yes</Call_Statistics_In_SIP_1>

Web Parameter

Call Statistics in SIP

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Adds the call quality statistics after the call ends to the end call message sent to the third-party call control server.

Labels

Servers

CDP

Syntax Description

XML Tag Name

CDP
Example:

<CDP>Yes</CDP>

Web Parameter

CDP Send

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Controls the use of Cisco Discovery Protocol (CDP) on the base.

Labels

Network

CDP_Delay

Syntax Description

XML Tag Name

Example:

<CDP_Delay>100</CDP_Delay>

Web Parameter

CDP Send Delay

Default Value

60

Allowed Values

Integer

Units

Integer

Limits

0-255 digits

User or Admin

Exposed in admin level

Description

Identifies the length of time, in seconds, that the device waits between CDP messages.

Labels

Network

Certificate_use_only_trusted

Syntax Description

XML Tag Name

Certificate_use_only_trusted
Example:

<Certificate_use_only_trusted>Yes</Certificate_use_only_trusted>

Web Parameter

Use Only Trusted Certificates

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

- No—Accepts all the certificates from the server.

- Yes—Verifies if the configured value of the outbound proxy (A/AAAA record, DNS SRV, or NAPTR domain) is present in the CN or SAN entry in the certificate present in the server. If the value doesn't match the entry in the certificate in the server, the TLS connection fails.

Labels

Security

Cfg_Rep_OnChange

Syntax Description

XML Tag Name

Cfg_Rep_OnChange

Web Parameter

Config Change Report On-Change

Default Value

x

Allowed Values

Option list: Disabled|Enable

Units

String

Limits

x

User or Admin

Exposed in admin level

Description

When enabled, a configuration update triggers a three minute timeout. Any configuration changes made within the next three minutes restart the timer. When there is no change in the configuration for three minutes, they are reported to the server.

Labels

Management

Cfg_Rep_Period

Syntax Description

XML Tag Name

Cfg_Rep_Period

Web Parameter

Config Change Report Period

Default Value

0

Allowed Values

Integer

Units

hours

Limits

0-744

User or Admin

Exposed in admin level

Description

Periodic reporting transmits changes to the configuration server at a defined period of hours after the configuration is set.

Labels

Management

Cfwd_All_Act_Code

Syntax Description

XML Tag Name

Cfwd_All_Act_Code
Example:

<Cfwd_All_Act_Code>*80</Cfwd_All_Act_Code>

Web Parameter

Call Forward All Activate

Default Value

*72

Allowed Values

Integer

Units

Integer

Limits

0-99 digits

User or Admin

Exposed in admin level

Description

Indicates to dial this star code to forward all calls.

Labels

Star Codes

Cfwd_All_Deact_Code

Syntax Description

XML Tag Name

Cfwd_All_Deact_Code
Example:

<Cfwd_All_Deact_Code>*85</Cfwd_All_Deact_Code>

Web Parameter

Call Forward All Deactivate

Default Value

*73

Allowed Values

Integer

Units

Integer

Limits

0-99 digits

User or Admin

Exposed in admin level

Description

Indicates to dial this star code to stop make calls ring on the phone again.

Labels

Star Codes

Cfwd_All_Dest_n_

Syntax Description

XML Tag Name

Cfwd_All_Dest_n_
Example:

<Cfwd_All_Dest_1_>1234/Cfwd_All_Dest_1_>

Web Parameter

Forwarding Unconditional Number

Default Value

None

Allowed Values

Integer

Units

Integer

Limits

21 characters

User or Admin

Exposed in admin level

Description

Identifies the number to dial when an incoming call arrives for the handset.

Applies to all incoming calls.

Labels

Extensions > Add or Edit Extension

Cfwd_All_Serv_n_

Syntax Description

XML Tag Name

Cfwd_All_Serv_n_
Example:

<Cfwd_All_Serv_1_>Yes</Cfwd_All_Serv_1_>

Web Parameter

Forwarding Unconditional Number

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Identifies if call forward unconditional is available.

Applies to all incoming calls.

Labels

Extensions > Add or Edit Extension

Cfwd_Busy_Dest_n_

Syntax Description

XML Tag Name

Cfwd_Busy_Dest_n_
Example:

<Cfwd_Busy_Dest_1_>1234</Cfwd_Busy_Dest_1_>

Web Parameter

Forwarding on Busy Number

Default Value

None

Allowed Values

String

Units

String

Limits

21 characters

User or Admin

Exposed in admin level

Description

Identifies the number to dial when the handset is busy.
Applies when the handset is on an existing call.

Labels

Extensions > Add or Edit Extension

Cfwd_Busy_Serv_n_

Syntax Description

XML Tag Name

Cfwd_Busy_Serv_n_
Example:

<Cfwd_Busy_Serv_1_>Yes</Cfwd_Busy_Serv_1_>

Web Parameter

Forwarding on Busy Number

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Identifies if call forward busy is available.
Applies when the handset is on an existing call.

Labels

Extensions > Add or Edit Extension

Cfwd_No_Ans_Delay_n

Syntax Description

XML Tag Name

Cfwd_No_Ans_Delay_n
Example:

<Cfwd_No_Ans_Delay_1>90</Cfwd_No_Ans_Delay_1>

Web Parameter

Forwarding No Answer Number

Default Value

90

Allowed Values

Integer

Units

Seconds

Limits

1-255

User or Admin

Exposed in admin level

Description

Indicates the wait time in seconds before the call is considered unanswered.
Applies to all unanswered calls.

Labels

Extensions > Add or Edit Extension

Cfwd_No_Ans_Dest_n_

Syntax Description

XML Tag Name

Cfwd_No_Ans_Dest_n_
Example:

<Cfwd_No_Ans_Dest_1_>1234</Cfwd_No_Ans_Dest_1_>

Web Parameter

Forwarding No Answer Number

Default Value

None

Allowed Values

String

Units

String

Limits

21 characters

User or Admin

Exposed in admin level

Description

Indicates the number to dial when an incoming call arrives for the handset and isn’t answered.
Applies to all unanswered calls.

Labels

Extensions > Add or Edit Extension

Cfwd_No_Ans_Serv_n_

Syntax Description

XML Tag Name

Cfwd_No_Ans_Serv_n_
Example:

<Cfwd_No_Ans_Serv_1_>Yes</Cfwd_No_Ans_Serv_n_>

Web Parameter

Forwarding No Answer Number

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if call forward no answer is available.
Applies to all unanswered calls.

Labels

Extensions > Add or Edit Extension

Conference_Bridge_URL_n_

Syntax Description

XML Tag Name

Conference_Bridge_URL_n_
Example:

<Conference_Bridge_URL_1_>conference@server.com</Conference_Bridge_URL_1_>

Web Parameter

Conference Server

Default Value

None

Allowed Values

Server URL

Units

Server URL

Limits

63 characters

User or Admin

Exposed in admin level

Description

Indicates the IP address or URL of the service provider's conference server, if available.

Labels

Servers

Conference_Serv_n_

Syntax Description

XML Tag Name

Conference_Serv_n_
Example:

<Conference_Serv_1_>Yes</Conference_Serv_n_>

Web Parameter

Enable Conference Server

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Controls the use of the external conference server.
If the value is Yes, an external conference server is configured.

When the user starts a conference, the handset starts a conference on the configured conference server.

Labels

Servers

Conference_Tone

Syntax Description

XML Tag Name

Conference_Tone
Example:

<Conference_Tone>350@-19;20(.1/.1/1,.1/9.7/1)</Conference_Tone>

Web Parameter

Conference Tone

Default Value

350@-19;20(.1/.1/1,.1/9.7/1)

Allowed Values

String

Units

String

Limits

256 characters

User or Admin

Exposed in admin level

Description

Indicates the tone that plays to all parties when a three-way conference call is in progress.

Labels

Call Progress Tones

ConfigurationDownloadCtrl

Syntax Description

XML Tag Name

ConfigurationDownloadCtrl
Example:

<ConfigurationDownloadCtrl>3</ConfigurationDownloadCtrl>

Web Parameter

Configuration File Download

Default Value

1

Allowed Values

Integer

Units

Integer

Limits

0-3 digits

User or Admin

Exposed in admin level

Description

Indicates the type of configuration file for the base station.

- 0: Download/resync disabled

- 1: Base Specific File. The base station expects a filename in the format [mac address].xml

- 2: Multi Cell specific File. The base station expects a filename in the format MultiCell_[chain id].cfg.

- 3: Base and Multi Cell Specific File. The base station expects a filename in the formats [mac address].xml and MultiCell_[chain id].cfg.

Labels

Management

Confirm_Tone

Syntax Description

XML Tag Name

Confirm_Tone
Example:

<Confirm_Tone>600@-16;1(.25/.25/1)</Confirm_Tone>

Web Parameter

Confirm Tone

Default Value

600@-16;1(.25/.25/1)

Allowed Values

String

Units

String

Limits

256 characters

User or Admin

Exposed in admin level

Description

Indicates the brief tone to notify the acceptance of the last input value to the user.

Labels

Call Progress Tones

Connection_Type

Syntax Description

XML Tag Name

Connection_Type
Example:

<Connection_Type>DHCP</Connection_Type>

Web Parameter

DHCP/Static IP

Default Value

DHCP

Allowed Values

- DHCP

- Static

Units

String

Limits

None

User or Admin

Exposed in admin level

Description

Indicates the method that the device gets the TCP/IP parameters.

- DHCP: Automatically allocated from a pool of addresses. If DHCP is used, the other IP settings or options can't be set.

- Static: Manually set.

Labels

Network

Country_Region_ID

Syntax Description

XML Tag Name

Country_Region_ID

Example:

<Country_Region_Id>4</Country_Region_Id>

Web Parameter

State / Region

Default Value

Alabama

Allowed Values

List of options

Units

Options without units

Limits

Option

User or Admin

Exposed in user/admin level

Description

Defines the selected state or region

Labels

Country

Country_Variant_ID

Syntax Description

XML Tag Name

Country_Variant_ID

Example:

<Country_Variant_Id>US</Country_Variant_Id>

Web Parameter

Select Country

Default Value

US

Allowed Values

List of options

Units

Options without units

Limits

Option

User or Admin

Exposed in user/admin level

Description

Defines the selected country

Labels

Country

CW_Act_Code

Syntax Description

XML Tag Name

CW_Act_Code
Example:

<CW_Act_Code>*65</CW_Act_Code>

Web Parameter

Call Wait Activate

Default Value

*56

Allowed Values

Integer

Units

Integer

Limits

0-99 digits

User or Admin

Exposed in admin level

Description

Indicates to dial this star code to enable the call waiting tone.

Labels

Star Codes

CW_Deact_Code

Syntax Description

XML Tag Name

CW_Deact_Code
Example:

<CW_Deact_Code>*70</CW_Deact_Code>

Web Parameter

Call Wait Deactivate

Default Value

*57

Allowed Values

Integer

Units

Integer

Limits

0-99

User or Admin

Exposed in admin level

Description

Indicates to dial this star code to disable the call waiting tone.

Labels

Star Codes

CW_Setting_n_

Syntax Description

XML Tag Name

CW_Setting_n_
Example:

<CW_Setting_1_>Yes</CW_Setting_1_>

Web Parameter

Call waiting feature

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Identifies if the call waiting is available on the phone. If the value is Yes, the handset receives an indication of a second incoming call while on another active call.

Labels

Extensions > Add or Edit Extension

Daylight_Saving_Time_By_Country_Region

Syntax Description

XML Tag Name

Daylight_Saving_Time_By_Country_Region
Example:

<Daylight_Saving_Time_By_Country_Region>No</Daylight_Saving_Time_By_Country_Region>

Web Parameter

Set timezone by country/region

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates that the base station uses the timezone setting from the country and state/region

Labels

Country

Daylight_Saving_Time_Enable

Syntax Description

XML Tag Name

Daylight_Saving_Time_Enable
Example:

<Daylight_Saving_Time_Enable>Auto</Daylight_Saving_Time_Enable>

Web Parameter

Set DST by country/region

Default Value

Auto

Allowed Values

- Auto

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the use of daylight savings time (DST) for the state or region.

Labels

Country

Daylight_Saving_Time_Rule

Syntax Description

XML Tag Name

Daylight_Saving_Time_Rule
Example:

<Daylight_Saving_Time_Rule>start=3/0/7/2;end=11/0/7/2;save=1</Daylight_Saving_Time_Rule>

Web Parameter

Daylight Saving Time (DST)

Default Value

start=3/0/7/2;end=11/0/7/2;save=1

Allowed Values

Start=month/start date/day/time; End=month/end date/day/time;Save=Automatic

Units

String

Limits

None

User or Admin

Exposed in admin level

Description

Indicates the configuration of daylight saving time. These are the values for Save:

- Automatic—Uses the settings associated with the country.

- Enabled—You need to set the rest of the DST fields.

- Disabled—No DST required.

Labels

Country

Debug_Level

Syntax Description

XML Tag Name

Debug_Level
Example:

<Debug_Level>1</Debug_Level>

Web Parameter

Syslog Level

Default Value

1

Allowed Values

- 0: Syslog off

- 1: Normal Operation

- 2: System Analyze

- 3: Debug

Units

Integer

Limits

0-3 digits

User or Admin

Exposed in admin level

Description

Identifies the level of system-level log messages to save on the syslog server.

- 0: Syslog off—No messages saved.

- 1: Normal Operation—Normal message for: operational events, incoming calls, outgoing calls, handset registration, DECT location, call lost due to busy, critical system errors, and general system information.

- 2: System Analyze—Captures logs for handset roaming and handset firmware updates status. The system analyze level also contains the messages from normal operation.

- 3: Debug—Captures logs for debugging problems.

Note

Don't enable System Analyze and Debug logs during normal operation. These logs can result in system slowdown.

Labels

Management

DHCP_Option_To_Use

Syntax Description

XML Tag Name

DHCP_Option_To_Use
Example:

<DHCP_Option_To_Use>66,160,159,150,60</DHCP_Option_To_Use>

Web Parameter

DHCP option priority

Default Value

66,160,159,150,60

Allowed Values

String

Units

String

Limits

31 characters

User or Admin

Exposed in admin level

Description

Identifies the priority of the DHCP options.

Labels

Management

Dial_Plan_n_

Syntax Description

XML Tag Name

Dial_Plan_n_
Example:

<Dial_Plan_4_>*xx|#xx|xx.|+x.</Dial_Plan_4_>

Web Parameter

Dial Plan ID

Default Value

None

Allowed Values

String. The value n is between 0 to 10.

Units

String

Limits

255 characters

User or Admin

Exposed in admin level

Description

Identifies the index of the dial plan.

Labels

Terminal

Dial_Plan_Subscription_n_

Syntax Description

XML Tag Name

Dial_Plan_Subscription_n_
Example:

<Dial_Plan_Subscription_1_>1</Dial_Plan_Subscription_1_>

Web Parameter

Dial Plan ID

Default Value

1

Allowed Values

Integer

Units

Integer

Limits

1–10 digits

User or Admin

Exposed in admin level

Description

Indicates the index of the dial plan. The value of this parameter is Dial_Plan_n_ where n is the index of the dial plan.

Labels

Extensions > Terminal

Directory_Enable

Syntax Description

XML Tag Name

Directory_Enable
Example:

<Directory_Enable>Yes</Directory_Enable>

Web Parameter

None

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates whether the XSI phonebook is enabled.
Set the parameter Directory_Enable to No when you use LDAP for directory (phonebook_server_location = 1).

Set the XML parameter Phonebook_Server_Location to 2 to use XSI.

Labels

None

Directory_Enterprise_Common_Enable

Syntax Description

XML Tag Name

Directory_Enterprise_Common_Enable
Example:

<Directory_Enterprise_Common_Enable>No</Directory_Enterprise_Common_Enable>

Web Parameter

EnterpriseCommon

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Allows to enable the Enterprise Common directory.

Labels

Central Directory

Directory_Enterprise_Common_Name

Syntax Description

XML Tag Name

Directory_Enterprise_Common_Name
Example:

<Directory_Enterprise_Common_Name>EnterpriseCommen</Directory_Enterprise_Common_Name>

Web Parameter

EnterpriseCommon

Default Value

EnterpriseCommon

Allowed Values

String

Units

String

Limits

39 characters

User or Admin

Exposed in admin level

Description

Indicates the display name of the Enterprise Common directory in the handset. For example, if this field is set to "Company", the handset displays "Company" instead of "Enterprise Common".

Labels

Central Directory

Directory_Enterprise_Name

Syntax Description

XML Tag Name

Directory_Enterprise_Name
Example:

<Directory_Enterprise_Name>Company</Directory_Enterprise_Name>

Web Parameter

Enterprise

Default Value

Enterprise

Allowed Values

String

Units

String

Limits

39 characters

User or Admin

Exposed in admin level

Description

Indicates the display name of the Enterprise directory in the handset.

Labels

Central Directory

Directory_Enterprise_Enable

Syntax Description

XML Tag Name

Directory_Enterprise_Enable
Example:

<Directory_Enterprise_Enable>No</Directory_Enterprise_Enable>

Web Parameter

Enterprise

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Allows to enable the Enterprise directory.

Labels

Central directory

Directory_Group_Common_Enable

Syntax Description

XML Tag Name

Directory_Group_Common_Enable
Example:

<Directory_Group_Common_Enable>No</Directory_Group_Common_Enable>

Web Parameter

GroupCommon

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Allows to enable the Group Common directory.

Labels

Central Directory

Directory_Group_Common_Name

Syntax Description

XML Tag Name

Directory_Group_Common_Name
Example:

<Directory_Group_Common_Name>EnterpriseCommon</Directory_Group_Common_Name>

Web Parameter

GroupCommon

Default Value

EnterpriseCommon

Allowed Values

String

Units

String

Limits

39 characters

User or Admin

Exposed in admin level

Description

Indicates the display name of the Group Common directory in the handset

Labels

Central Directory

Directory_Group_Name

Syntax Description

XML Tag Name

Directory_Group_Name
Example:

<Directory_Group_Name>Group</Directory_Group_Name>

Web Parameter

Group

Default Value

Group

Allowed Values

String

Units

String

Limits

39 characters

User or Admin

Exposed in admin level

Description

Indicates the display name of the Group directory in the handset

Labels

Central Directory

Directory_Group_Name_Enable

Syntax Description

XML Tag Name

Directory_Group_Name_Enable
Example:

<Directory_Group_Name_Enable>No</Directory_Group_Name_Enable>

Web Parameter

Group

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Allows to enable the Group directory.

Labels

Central directory

Directory_Personal_Name

Syntax Description

XML Tag Name

Directory_Personal_Name
Example:

<Directory_Personal_Name>Home</Directory_Personal_Name>

Web Parameter

Personal

Default Value

Personal

Allowed Values

String

Units

String

Limits

39 characters

User or Admin

Exposed in admin level

Description

Indicates the display name of the Personal directory in the handset

Labels

Central Directory

Directory_Personal_Name_Enable

Syntax Description

XML Tag Name

Directory_Personal_Name_Enable
Example:

<Directory_Personal_Name_Enable>No</Directory_Personal_Name_Enable>

Web Parameter

Personal

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Allows to enable the Personal directory.

Labels

Central Directory

Display_Name_n_

Syntax Description

XML Tag Name

Display_Name_n_
Example:

<Display_Name_1_>Line 1</Display_Name_1_>

Web Parameter

Display Name

Default Value

None

Allowed Values

String

Units

String

Limits

29 characters

User or Admin

Exposed in admin level

Description

Identifies the name to display on the handset.

Labels

Extensions > Add or Edit Extension

DND_Act_Code

Syntax Description

XML Tag Name

DND_Act_Code
Example:

<DND_Act_Code>*80</DND_Act_Code>

Web Parameter

Do Not Disturb Activate

Default Value

*78

Allowed Values

Integer

Units

Integer

Limits

0-99 digits

User or Admin

Exposed in admin level

Description

Indicates the star code to dial to stop calls ringing on the phone.

Labels

Star Codes

DND_Deact_Code

Syntax Description

XML Tag Name

DND_Deact_Code
Example:

<DND_Deact_Code>*85</DND_Deact_Code>

Web Parameter

Do Not Disturb

Default Value

*79

Allowed Values

Integer

Units

Integer

Limits

0-99

User or Admin

Exposed in admin level

Description

Indicates the star code to dial to allow calls to ring on the phone.

Labels

Star Codes

DTMF_Tx_Method_n_

Syntax Description

XML Tag Name

DTMF_Tx_Method_n_
Example:

<DTMF_Tx_Method_1_>AVT</DTMF_Tx_Method_1_>

Web Parameter

DTMF Signalling

Default Value

AVT

Allowed Values

- INFO

- AVT

- AVT_AND_INFO

Units

String

Limits

None

User or Admin

Exposed in admin level

Description

Controls how to handle DTMF.

- INFO—Advertises the support for SIP INFO DTMF.

- AVT: RTP Events (RFC2833)—Advertises the support for RFC2833 DTMF.

- AVT_AND_INFO: SIP-Info and RTP Events (RFC2833)—Advertises the support for SIP INFO and RFC2833 DTMF.

Labels

Servers

Dual_Cell_Replacement_Timeout

Syntax Description

XML Tag Name

Dual_Cell_Replacement_Timeout

Example:

<Dual_Cell_Replacement_Timeout>15</Dual_Cell_Replacement_Timeout>

This parameter is only applicable for 110 Single-Cell Base Station.

Web Parameter

Base Replacement Timeout (15-255 Min)

Default Value

60

Allowed Values

Integer

Units

Minutes

Limits

Integer ranges from 15 to 255

User or Admin

Exposed in admin level

Description

Indicates the time to replace the base station.

Labels

Dual Cell

Emergency_Alarm_Block_Time

Syntax Description

XML Tag Name

Emergency_Alarm_Block_Time
Example:

<Emergency_Alarm_Block_Time>10</Emergency_Alarm_Block_Time>

Web Parameter

None

Default Value

0

Allowed Values

Integer

Units

Seconds

Limits

0-254

User or Admin

Exposed in admin level

Description

Indicates the period in which a new alarm can't interrupt an active alarm.

Labels

None

Emergency_Alarm_Howling_n_

Syntax Description

XML Tag Name

Emergency_Alarm_Howling_n_
Example:

<Emergency_Alarm_Howling_1_>Disabled</Emergency_Alarm_Howling_1_>

Web Parameter

Howling

Default Value

Disabled

Allowed Values

- Disabled

- Enabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if the handset should start the howling signal.

If disabled, only the call or message signal is sent.

Labels

Alarm

Emergency_Alarm_Number_n_

Syntax Description

XML Tag Name

Emergency_Alarm_Number_n_
Example:

<Emergency_Alarm_Number_n_>1234056</Emergency_Alarm_Number_n_>

Web Parameter

list of numbers

Default Value

None

Allowed Values

Integer

Units

Integer

Limits

0-7 digits

User or Admin

Exposed in admin level

Description

Indicates the defined emergency numbers.

Labels

Management

Emergency_Alarm_Priority_n_

Syntax Description

XML Tag Name

Emergency_Alarm_Priority_n_
Example:

<Emergency_Alarm_Priority_1_>0x00</Emergency_Alarm_Priority_1_>

Web Parameter

Idx

Default Value

0x00

Allowed Values

Hexadecimal

Units

Hexadecimal

Limits

0–7 digits

User or Admin

Exposed in admin level

Description

Indicates the priority of the alarm. A higher priority alarm can interrupt an active lower priority alarm.

Labels

Alarm

Emergency_Alarm_Signal_n_

Syntax Description

XML Tag Name

Emergency_Alarm_Signal_n_
Example:

<Emergency_Alarm_Signal_1_>0x01</Emergency_Alarm_Signal_1_>

Web Parameter

Alarm Signal

Default Value

0x01

Allowed Values

- 0x01

- 0x02

Units

Hexadecimal

Limits

Hexadecimal

User or Admin

Exposed in admin level

Description

Indicates how the alarm signals when the handset activates the alarm (Emergency) button.

- 0x01: Message—A text message is sent to the alarm server.

- 0x02: Call—An outgoing call is placed to the specified emergency number.

Labels

Alarm

Emergency_Alarm_Stop_Allowed_n_

Syntax Description

XML Tag Name

Emergency_Alarm_Stop_Allowed_n_
Example:

<Emergency_Alarm_Stop_Allowed_1_>Yes</Emergency_Alarm_Stop_Allowed_1_>

Web Parameter

Stop Alarm from Handset

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Identifies if the handset can cancel the alarm.

Labels

Alarm

Emergency_Alarm_Type_n_

Syntax Description

XML Tag Name

Emergency_Alarm_Type_n_
Example:

<Emergency_Alarm_Type_1_>0x04</Emergency_Alarm_Type_1_>

Web Parameter

Alarm Type

Default Value

0x04

Allowed Values

Hexadecimal

Units

Hexadecimal

Limits

4 and 5

User or Admin

Exposed in admin level

Description

Identifies the type of alarm.

- 4: Alarm Button

- 5: Disabled

Labels

Alarm

Emergency_Number_n_

Syntax Description

XML Tag Name

Emergency_Number_n_
Example:

<Emergency_Number_1_>0</Emergency_Number_1_>

Web Parameter

Alarm Number

Default Value

0

Allowed Values

Integer

Units

Integer

Limits

20 digits

User or Admin

Exposed in admin level

Description

Identifies the number to dial when a user presses and holds the Emergency button on the handset for 3 seconds or more.

Labels

Terminal

Emergency_Pre_Alarm_Delay_n_

Syntax Description

XML Tag Name

Emergency_Pre_Alarm_Delay_n_
Example:

<Emergency_Pre_Alarm_Delay_1_>0</Emergency_Pre_Alarm_Delay_1_>

Web Parameter

Pre-Alarm Delay

Default Value

0

Allowed Values

Integer

Units

Integer

Limits

0-255 digits

User or Admin

Exposed in admin level

Description

Indicates the delay between the time the pre-alarm displays and the time the alarm signals.

Labels

Alarm

Emergency_Pre_Alarm_Stop_Allowed_n_

Syntax Description

XML Tag Name

Emergency_Pre_Alarm_Stop_Allowed_n_
Example:

<Emergency_Pre_Alarm_Stop_Allowed_1_>Yes</Emergency_Pre_Alarm_Stop_Allowed_1_>

Web Parameter

Stop Pre-Alarm from Handset

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Identifies if the user can stop an alarm.

Labels

Alarm

Emergency_Profile_Alias_n_

Syntax Description

XML Tag Name

Emergency_Profile_Alias_n_
Example:

<Emergency_Profile_Alias_1_>Emergency</Emergency_Profile_Alias_1_>

Web Parameter

Profile Alias

Default Value

None

Allowed Values

String

Units

String

Limits

19 characters

User or Admin

Exposed in admin level

Description

Identifies the name of the alarm. This parameter is available only if you set the value of the parameter Emergency_Alarm_Type_n_ to 4(Alarm Button).

Labels

Alarm

Emergency_Trigger_Delay_n_

Syntax Description

XML Tag Name

Emergency_Trigger_Delay_n_
Example:

<Emergency_Trigger_Delay_1_>0</Emergency_Trigger_Delay_1_>

Web Parameter

Trigger Delay

Default Value

0

Allowed Values

Integer

Units

Integer

Limits

0-255 digits

User or Admin

Exposed in admin level

Description

Identifies the delay in seconds before the handset displays a pre-alarm warning.

- 0—No pre-alarm warning; the alarm is sent immediately.

- Other—The amount of time that the pre-alarm warning displays. When the number of seconds passes, the alarm is sent. It may take a few seconds for the alarm to be sent to the configured location.

Labels

Alarm

Enable_Protocol

Syntax Description

XML Tag Name

Enable_Protocol
Example:

<Enable_Protocol>HTTPS</Enable_Protocol>

Web Parameter

Secure HTTP

Default Value

HTTPS

Allowed Values

- HTTP

- HTTPS

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the protocol to access the base station web page.

Labels

Security

Enable_Web_Server

Syntax Description

XML Tag Name

Enable_Web_Server
Example:

<Enable_Web_Server>Yes</Enable_Web_Server>

Web Parameter

None

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates to allow to edit the configuration on the web server. If the value is Yes, it allows to edit the configuration on the web server.

Labels

None

Encryption_Method_n_

Syntax Description

XML Tag Name

Encryption_Method_n_
Example:

<Encryption_Method_1_>0</Encryption_Method_1_>

Web Parameter

SRTP Crypto Suites

Default Value

0

Allowed Values

- 0: AES_CM_128_HMAC_SHA1_32, AES_CM_128_HMAC_SHA1_80

- 1: AES_CM_128_HMAC_SHA1_80, AES_CM_128_HMAC_SHA1_32

- 2: AES_CM_128_HMAC_SHA1_32

- 3: AES_CM_128_HMAC_SHA1_80

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the list of supported SRTP Crypto Suites. Each device starts with two suites. You can change the order of the suites.

Labels

Servers

Feature_Key_Sync_n_

Syntax Description

XML Tag Name

Feature_Key_Sync_n_
Example:

<Feature_Key_Sync_1_>Disabled</Feature_Key_Sync_1_>

Web Parameter

BroadWorks Feature Event Package

Default Value

Disabled

Allowed Values

- Disabled

- Enabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Identifies if the BroadWorks feature key sync package is available. Features include: do not disturb, call forward (all, busy, no answer).

Only applicable to BroadSoft SIP servers. Must be enabled on the SIP server.

Labels

Extensions > Add or Edit Extension

FilenameMultiSpecific

Syntax Description

XML Tag Name

FilenameMultiSpecific
Example:

<FilenameMultiSpecific>LINKID_012345.xml</FilenameMultiSpecific>

Web Parameter

Multi Cell Specific File

Default Value

None

Allowed Values

String

Units

String

Limits

31 characters

User or Admin

Exposed in admin level

Description

This parameter is the second configuration file to download and use for multicell configuration. This parameter is dependent on the parameters NETWORK_CONFIGURATION_SERVER and CONFIGURATION_DOWNLOAD_CTRL.
If this filename is empty, the NETWORK_SYNC_ID adds the ID to this filename MultiCell_ID.cfg.

Labels

Management

Firewall

Syntax Description

XML Tag Name

Firewall

Example:

<Firewall>[Parameter]</Firewall>

Web Parameter

Firewall

Default Value

Enabled

Allowed Values

Enabled|Disabled

Units

Limits

List

User or Admin

Exposed in admin level

Description

Enables statefull firewall to control incoming network traffic for Cisco IP DECT 110 Single-Cell Base Station and Cisco IP DECT 210 Multi-Cell Base Station.

Labels

Security

Firewall_Config

Syntax Description

XML Tag Name

Firewall_Config

Example:

<Firewall_Config ua=”na”>NO_ICMP_PING,TCP:12000,UDP:8000:8010</Firewall_Config>

Web Parameter

Default Value

Blank

Allowed Values

NO_ICMP_PING |NO_ICMP_UNREACHABLE|NO_NONDEFAULT_TFTP

Units

Options without limits

Limits

Options

User or Admin

Exposed in admin level

Description

Configures firewall for port range.

Labels

Security

Gateway

Syntax Description

XML Tag Name

Gateway
Example:

<Gateway>192.168.0.1</Gateway>

Web Parameter

Default Gateway

Default Value

None

Allowed Values

IP address

Units

IP address

Limits

IP address

User or Admin

Exposed in admin level

Description

Indicates the IPv4 address of the default network router or gateway.

You can change this parameter only if DHCP is not enabled.

Labels

Network

Group_Paging_Script_n_

Syntax Description

XML Tag Name

Group_Paging_Script_n_

Example:

<Group_Paging_Script_1_>pggrp=224.168.168.169:34560;
name=All;num=500;listen=yes;pri=0</Group_Paging_Script_1_>

Web Parameter

Group 1-3 Paging Script

Default Value

None

Allowed Values

String. The value n is 1 to 3.

Units

String

Limits

128 characters

User or Admin

Exposed in admin level

Description

A string to configure the phone to listen and initiate multicast paging. Each string can have a maximum length of 128 characters. You can add a phone to up to 3 paging groups.

Labels

Management

Handle_VIA_received_n_

Syntax Description

XML Tag Name

Handle_VIA_received_n_
Example:

<Handle_VIA_received_1_>No</Handle_VIA_received_1_>

Web Parameter

NAT Adaption

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates how to handle SIP messages in a SIP-aware router.

- Yes—When the system receives a SIP response to a REGISTER request with a Via header that includes the received parameter, the base adapts its contact information to the IP address from the received parameter. For example, Via: SIP/2.0/UDP 10.1.1.1:4540;received=68.44.20.1. The base issues another REGISTER request with the updated contact information.

No—The received parameter is ignored.

Labels

Servers

Handset_Alarm_Auto_Stop_Allowed

Syntax Description

XML Tag Name

Handset_Alarm_Auto_Stop_Allowed
Example:

<Handset_Alarm_Auto_Stop_Allowed>Disabled</Handset_Alarm_Auto_Stop_Allowed>

Web Parameter

Auto Stop Alarm

Default Value

Disabled

Allowed Values

- Disabled

- Enabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if the handset should stop the automatic emergency notification.

- Disabled—The handset doesn't stop notification.

- Enabled—The handset stops the notification after the number of seconds set in Auto Stop Alarm Delay.

Labels

Management

Handset_Alarm_Auto_Stop_Delay

Syntax Description

XML Tag Name

Handset_Alarm_Auto_Stop_Delay
Example:

<Handset_Alarm_Auto_Stop_Delay>30</Handset_Alarm_Auto_Stop_Delay>

Web Parameter

Auto Stop Alarm Delay(s)

Default Value

30

Allowed Values

Integer

Units

Seconds

Limits

0-255 digits

User or Admin

Exposed in admin level

Description

Indicates the time (in seconds) before the handset stops automatic emergency notification.

Labels

Management

Handset_Keepalive_Delay

Syntax Description

XML Tag Name

Handset_Keepalive_Delay
Example:

<Handset_Keepalive_Delay>0</Handset_Keepalive_Delay>

Web Parameter

Keep Alive (m)

Default Value

0

Allowed Values

Integer

Units

Minutes

Limits

0-255

User or Admin

Exposed in admin level

Description

Indicates the length of time in minutes that the handset waits before sending an automatic emergency notification message to the server.

If the value is not 0, the handset doesn't send notifications.

Labels

Management

Hs_Alarm_Enable_n_

Syntax Description

XML Tag Name

Hs_Alarm_Enable_n_

Example:

<Hs_Alarm_Enable_1_>Yes</Hs_Alarm_Enable_1_>

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

Description

Specifies that the alarm is enabled.

Handset Menu

None

Hs_Config_Protocol

Syntax Description

XML Tag Name

Hs_Config_Protocol

Example:

<Hs_Config_Protocol>IPv4</Hs_Config_ Protocol>

Web Parameter

Protocol

Default Value

IPv4

Allowed Values

- IPv4

- IPv6

Units

Options without units

Limits

Option

Description

Indicates the protocol to download the handset configuration file.

Labels

Management

Hs_Config_Server

Syntax Description

XML Tag Name

Hs_Config_Server

Example:

<Hs_Config_Server>https://cisco.com/path/handset.xml</Hs_Config_Server>

Web Parameter

Configuration server and file

Default Value

None

Allowed Values

URL

Units

URL

Limits

URL

Description

Defines the server and the handset configuration file to download.

Labels

Management

Hs_Config_Server_Password

Syntax Description

XML Tag Name

Hs_Config_Server_Password

Example:

<Hs_Config_Server_Password>Abcd123</Hs_Config_Server_Password>

Web Parameter

Password

Default Value

None

Allowed Values

String

Units

String

Limits

40 characters

Description

Indicates the password to access the handset configuration server.

Labels

Management

Hs_Config_Server_Username

Syntax Description

XML Tag Name

Hs_Config_Server_Username

Example:

<Hs_Config_Server_Username>LoginName</ Hs_Config_Server_Username >

Web Parameter

Username

Default Value

None

Allowed Values

String

Units

String

Limits

40 characters

Description

Indicates the username to access the handset configuration server.

Handset Menu

Management

Hebu_Mode

Syntax Description

XML Tag Name

Hebu_Mode

Example:

<Hebu_Mode>enabled</Hebu_Mode>

Web Parameter

Assing HS to Ext by Credentials

Default Value

Disabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Options

User or Admin

Exposed in admin level

Description

Indicates if the Handset Extension by Username (HEBU) is enabled.

Labels

Management

Held_Company_Id

Syntax Description

XML Tag Name

Held_Company_Id

Example:

<Held_Company_Id>ABC123</Held_Company_Id>

Web Parameter

HELD Company ID

Default Value

None

Allowed Values

String

Units

String

Limits

40 characters

User or Admin

Exposed in admin level

Description

Specifies the HTTP Enabled Location Delivery company account ID (RedSky).

Labels

Management

Held_Token_Srvn

Syntax Description

XML Tag Name

Held_Token_Srvn

Where n is 1 for the primary HELD server and 2 for the secondary HELD server.

Example:

<Held_Token_Srv1></Held_Token_Srv1>

<Held_Token_Srv2></Held_Token_Srv2>

Web Parameter

Primary HELD Server

Default Value

Empty

Allowed Values

String

Units

String

Limits

128 characters

User or Admin

Exposed in admin level

Description

Specifies the primary or secondary HELD server.

Labels

Management

Holding_Tone

Syntax Description

XML Tag Name

Holding_Tone
Example:

<Holding_Tone>600@-19;*(.1/.1/1,.1/.1/1,.1/9.5/1)</Holding_Tone>

Web Parameter

Holding Tone

Default Value

600@-19;*(.1/.1/1,.1/.1/1,.1/9.5/1)

Allowed Values

String

Units

String

Limits

256 characters

User or Admin

Exposed in admin level

Description

Informs the local caller that the far end has placed the call on hold.

Labels

Call Progress Tones

Insert_VIA_rport

Syntax Description

XML Tag Name

Insert_VIA_rport
Example:

<Insert_VIA_rport>No</Insert_VIA_rport>

Web Parameter

Enable RPORT

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the use of RPORT in SIP messages.

Labels

Network

Ieee1588_Enabled

Syntax Description

XML Tag Name

Ieee1588_Enabled
Example:

<Ieee1588_Enabled>No</Ieee1588_Enabled>

Web Parameter

IEEE1588

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the use of LAN synchronization for Multicell synchronization between the base stations.

Labels

LAN Sync

Ieee1588_Zone_Multicast_Alt_Domain

Syntax Description

XML Tag Name

Ieee1588_Zone_Multicast_Alt_Domain
Example:

<Ieee1588_Zone_Multicast_Alt_Domain>80
</Ieee1588_Zone_Multicast_Alt_Domain>

Web Parameter

Alternativ Domain Number

Default Value

64

Allowed Values

Integer

Units

Integer

Limits

0-127 digits

User or Admin

Exposed in admin level

Description

Indicates the alternate Zone Multicast Domain number to use with this parameter.

Labels

LAN Sync

Ieee1588_Zone_Multicast_Domain

Syntax Description

XML Tag Name

Ieee1588_Zone_Multicast_Domain
Example:

<Ieee1588_Zone_Multicast_Domain>50</Ieee1588_Zone_Multicast_Domain>

Web Parameter

Alternativ Domain Number

Default Value

0

Allowed Values

Integer

Units

Integer

Limits

0-127 digits

User or Admin

Exposed in admin level

Description

Zone Multicast Domain number to be used with the IEEE1588 Synchronisation.

Labels

LAN Sync

Ieee1588_Zone_Multicast_Ip

Syntax Description

XML Tag Name

Ieee1588_Zone_Multicast_Ip
Example:

<Ieee1588_Zone_Multicast_Ip>224.0.1.129
</Ieee1588_Zone_Multicast_Ip>

Web Parameter

Multicast IP Address

Default Value

224.0.1.129

Allowed Values

IP Address

Units

IP Address

Limits

IP Address

User or Admin

Exposed in admin level

Description

Indicates the Zone multicast static IP list to use to communicate peer to peer.

The input format is IPv4: xxx.xxx.xxx.xxx

Labels

LAN Sync

Ieee1588_Zone_Multicast_Port

Syntax Description

XML Tag Name

Ieee1588_Zone_Multicast_Port
Example:

<Ieee1588_Zone_Multicast_Port>400</Ieee1588_Zone_Multicast_Port>

Web Parameter

Multicast Port

Default Value

319

Allowed Values

Integer

Units

Integer

Limits

0-65535 digits

User or Admin

Exposed in admin level

Description

Indicates the Zone multicast port to use with the IEEE1588 Synchronisation.

Labels

LAN Sync

INVITE_Expires

Syntax Description

XML Tag Name

INVITE_Expires
Example:

<INVITE_Expires>1800</INVITE_Expires>

Web Parameter

Session Timer Value (s)

Default Value

1800

Allowed Values

Integer

Units

Seconds

Limits

0-65535

User or Admin

Exposed in admin level

Description

Indicates the length of time in seconds for the SIP Session Timer.

Labels

Servers

Language_Rule

Syntax Description

XML Tag Name

Language_Rule

Example:

<Language_Rule>https://www.server.com/path/6825_mycustomtexts.xml</Language_Rule>

Web Parameter

Language Pack

Default Value

None

Allowed Values

URL

Units

URL

Limits

URL

User or Admin

Exposed in admin level

Description

Indicates the language file location for a handset update.

Labels

Firmware Update

Language_Selection

Syntax Description

XML Tag Name

handset_Language

Example:

<handset_Language>Magyar</handset_Language>

Web Parameter

None

Default Value

English

Allowed Values

List of options

Units

Options without units

Limits

Option

User or Admin

Exposed in user level

Description

Defines the selected language

Labels

None

LDAP_Username

Syntax Description

XML Tag Name

LDAP_Username
Example:

- <LDAP_Username>CN=Dummy,OU=umber,DC=umber,DC=loc</LDAP_Username>

- <LDAP_Username>username</LDAP_Username>

- <LDAP_Username>user@domain</LDAP_Username>

Web Parameter

Bind

Default Value

None

Allowed Values

String

Units

String

Limits

127 characters

User or Admin

Exposed in admin level

Description

Identifies the user name to use when the phone connects to the server.

Labels

Central Directory

LDAP_Dir_Enable

Syntax Description

XML Tag Name

LDAP_Dir_Enable
Example:

<LDAP_Dir_Enable>No</LDAP_Dir_Enable>

Web Parameter

Central Directory Location

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the use of LDAP directory.

Labels

Central Directory

LDAP_Display_Attrs

Syntax Description

XML Tag Name

LDAP_Display_Attrs
Example:

<LDAP_Display_Attrs>a=cn,n=cn;a=givenName,n=firstname;a=sn,n=lastname;
a=telephoneNumber,n=telephoneNumber,t=p;a=homePhone,n=homePhone,t=p;a=mobile,
n=mobile,t=p;</LDAP_Display_Attrs>

Web Parameter

Name, Work, Home, and Mobile

Default Value

a=cn,n=cn;a=givenName,n=firstname;a=sn,n=lastname;a=telephoneNumber,
n=telephoneNumber,t=p;a=homePhone,n=homePhone,t=p;a=mobile,n=mobile,t=p;

Allowed Values

String

Units

String

Limits

127 characters

User or Admin

Exposed in admin level

Description

Name: Indicates whether the common name or surname with the given name returns in the LDAP search results.

Work: Indicates LDAP work number attribute which maps to the handset work number.

Home: Indicates LDAP home number attribute which is maps to the handset home number.

Mobile: Indicates LDAP mobile number attribute which is maps to the handset mobile number.

Labels

Central Directory

LDAP_First_Name_Filter

Syntax Description

XML Tag Name

LDAP_First_Name_Filter
Example:

<LDAP_First_Name_Filter>cn:(cn=John*)</LDAP_First_Name_Filter>

Web Parameter

LDAP Filter

Default Value

None

Allowed Values

String

Units

String

Limits

127 characters

User or Admin

Exposed in admin level

Description

Identifies the search filter. For example, if the field is set to (|(givenName=%*)(sn=%*)), the system uses this filter when it requests entries from the LDAP server. % replaces with the content which the user enters during the search operation. If a user enters J for the search criteria, the string sent to the server is (|(givenName=J*)(sn=J*)) and server sends the matches for given names or surnames that start with the letter J.

Labels

Central Directory

LDAP_Last_Name_Filter

Syntax Description

XML Tag Name

LDAP_Last_Name_Filter
Example:

<LDAP_Last_Name_Filter>sn:(sn=L*)</LDAP_Last_Name_Filter>

Web Parameter

LDAP Filter

Default Value

None

Allowed Values

String

Units

String

Limits

127 characters

User or Admin

Exposed in admin level

Description

Identifies the search filter. For example, if the field is set to (|(givenName=%*)(sn=%*)), the system uses this filter when it requests entries from the LDAP server. % replaces with the content which the user enters during the search operation. If a user enters J for the search criteria, the string sent to the server is (|(givenName=J*)(sn=J*)) and server sends the matches for given names or surnames that start with the letter J.

Labels

Central Directory

LDAP_Password

Syntax Description

XML Tag Name

LDAP_Password
Example:

<LDAP_Password>passwrd12</LDAP_Password>

Web Parameter

Password

Default Value

None

Allowed Values

String

Units

String

Limits

127 characters

User or Admin

Exposed in admin level

Description

Contains the LDAP Server password.

Labels

Central Directory

LDAP_Search_Base

Syntax Description

XML Tag Name

LDAP_Search_Base
Example:

<LDAP_Search_Base>dc=cv2bu,dc=com</LDAP_Search_Base>

Web Parameter

Sbase

Default Value

None

Allowed Values

String

Units

String

Limits

127 characters

User or Admin

Exposed in admin level

Description

Identifies the search base criteria.
Example:

CN=Users, DC=number, DC=loc

Labels

Central Directory

LDAP_Server

Syntax Description

XML Tag Name

LDAP_Server
Example:

<LDAP_Server>ldapserver.com</LDAP_Server>

Web Parameter

Server

Default Value

None

Allowed Values

String

Units

String

Limits

127 characters

User or Admin

Exposed in admin level

Description

Identifies the server that contains the directory file.

Labels

Central Directory

Ldap_Virtual_Lists

Syntax Description

XML Tag Name

Ldap_Virtual_Lists
Example:

<Ldap_Virtual_Lists>Enabled</Ldap_Virtual_Lists>

Web Parameter

Virtual List

Default Value

Enabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Controls if virtual list search is possible.

- Disabled: All search results are loaded.

- Enabled: Only 25 contacts are loaded at a time.

Labels

Central Directory

Line_Enable_n_

Syntax Description

XML Tag Name

Line_Enable_n_
Where n is 1 to 1000

Example:

<Line_Enable_1_>Yes</Line_Enable_1_>

Web Parameter

None

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if an account is configured and active.

- Yes: The account is configured and active.

- No: The account isn't active.

Labels

None

Line_Name_n_

Syntax Description

XML Tag Name

Line_Name_n_
Example:

<Line_Name_1_>Test</Line_Name_1_>

Web Parameter

Line Name

Default Value

None

Allowed Values

String

Units

String

Limits

7 characters

User or Admin

Exposed in admin level

Description

Indicates the short name for the extension when you use multiple lines.

Labels

Extensions > Add or Edit Extension

LLDP

Syntax Description

XML Tag Name

LLDP

Example:

<LLDP>No</LLDP>

Web Parameter

LLDP-MED Send

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Controls the use of Link Layer Discovery Protocol (LLDP) on the base.

If the value is Yes, the base station sends 5 LLDP-MED messages after it starts.

Labels

Network

LLDP_Delay

Syntax Description

XML Tag Name

LLDP_Delay

Example:

<LLDP_Delay>30</LLDP_Delay>

Web Parameter

LLDP-MED Send Delay

Default Value

30

Allowed Values

Integer

Units

Seconds

Limits

0-255

User or Admin

Exposed in admin level

Description

Identifies the length of time, in seconds, that the device waits between LLDP-MED messages.

Note

The parameter LLDP must be enabled to use this option.

Labels

Network

Login_Password

Syntax Description

XML Tag Name

Login_Password

Example:

<Login_Password>Test123@</Login_Password>

Web Parameter

XSI Password

Default Value

None

Allowed Values

String

Units

String

Limits

128 characters

User or Admin

Exposed in admin level

Description

Identifies the password for the BroadSoft XSI phone book.

Labels

Extensions > Add or Edit Extension

Login_User_ID

Syntax Description

XML Tag Name

Login_User_ID

Example:

<Login_User_ID>Testuser</Login_User_ID>

Web Parameter

XSI Username

Default Value

None

Allowed Values

String

Units

String

Limits

128 characters

User or Admin

Exposed in admin level

Description

Identifies the username for the BroadSoft XSI phone book.

Labels

Extensions > Add or Edit Extension

Mailbox_ID_n_

Syntax Description

XML Tag Name

Mailbox_ID_n_

Example:

<Mailbox_ID_1_>Testmail</Mailbox_ID_1_>

Web Parameter

Mailbox Name

Default Value

None

Allowed Values

String

Units

String

Limits

39 characters

User or Admin

Exposed in admin level

Description

Identifies the username for the voicemail system.

The SUBSCRIBE request uses this username, if specified, when subscribing to the Voice Mail service.

Labels

Extensions > Add or Edit Extension

Management_Factory_Reset_From_Button

Syntax Description

XML Tag Name

Management_Factory_Reset_From_Button

Example:

<Management_Factory_Reset_From_Button>Enabled</Management_Factory_Reset_From_Button>

Web Parameter

Factory reset from button

Default Value

Enabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates whether you can use the reset button to factory reset the base station. When set to Disabled, nothing happens when you press the reset button.

Labels

Management

MDNS_Support

Syntax Description

XML Tag Name

MDNS_Support

Example:

<MDNS_Support>No</MDNS_Support>

Web Parameter

MDNS

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if Multicast Domain Name System (MDNS) is available.

DHCP should be disabled to change this parameter.

Labels

Network

MediasSec_Over_TLS_Only_n_

Syntax Description

XML Tag Name

MediasSec_Over_TLS_Only_n_

Example:

<MediasSec_Over_TLS_Only_1_>Disabled</MedissSec_Over_TLS_Only_1_>

Web Parameter

Media Security only for TLS

Default Value

Disabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Controls the media security only if the SIP transfer protocol is TLS. This option can be enabled only if the Media Security is enabled.

Labels

Servers

MediaSec_Request_n_

Syntax Description

XML Tag Name

MediaSec_Request_n_

Example:

<MediaSec_Request_1_>Enabled</MediaSec_Request_1_>

Web Parameter

Media Security

Default Value

Disabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Controls the media security.

- Enabled: Client-initiated Mode—The phone initiates media security negotiations.

- Disabled: Server-initiated Mode—The server initiates media security negotiations. The phone doesn't initiate negotiations, but can handle negotiation requests from the server to establish secure calls.

Labels

Servers

NAT_Keep_Alive_Intvl

Syntax Description

XML Tag Name

NAT_Keep_Alive_Intvl

Example:

<NAT_Keep_Alive_Intvl>90</NAT_Keep_Alive_Intvl>

Web Parameter

Keep alive time

Default Value

90

Allowed Values

Integer

Units

Seconds

Limits

0-65535

User or Admin

Exposed in admin level

Description

Determines the frequency of keep alive messages (in seconds) to the server to maintain NAT bindings.

Labels

Network

NetMask

Syntax Description

XML Tag Name

NetMask

Example:

<NetMask>255.255.255.0</NetMask>

Web Parameter

Subnet Mask

Default Value

None

Allowed Values

IP address

Units

IP Address

Limits

IP Address

User or Admin

Exposed in admin level

Description

Indicates the 32-bit subnet mask of the device. DHCP should be disabled to change this parameter.

Labels

Network

Network_Allow_Multi_Primary

Syntax Description

XML Tag Name

Network_Allow_Multi_Primary

Example:

<Network_Allow_Multi_Primary>No</Network_Allow_Multi_Primary>

Web Parameter

Allow multi primary

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Allows the setup of one multicell in multiple locations.

Labels

Multi Cell

Network_Auto_Multi_Primary

Syntax Description

XML Tag Name

Network_Auto_Multi_Primary

Example:

<Network_Auto_Multi_Primary>No</Network_Auto_Multi_Primary>

Web Parameter

Auto create multi primary

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if you can auto configure multiple primary in a chain.

Labels

Multi Cell

Network_Data_Config_Primary_Mac

Syntax Description

XML Tag Name

Network_Data_Config_Primary_Mac
Example:

<Network_Data_Config_Primary_Mac>0C:75:BD:33:D5:01
</Network_Data_Config_Primary_Mac>

Web Parameter

None

Default Value

0xFFFFFFFFF

Allowed Values

MAC address

Units

MAC address

Limits

MAC address

User or Admin

Exposed in admin level

Description

Specifies the MAC address of the base station which allows to download and handle multicell configuration file.

Labels

None

Network_Dect_Auto_Sync_Tree_Config

Syntax Description

XML Tag Name

Network_Dect_Auto_Sync_Tree_Config
Example:

<Network_Dect_Auto_Sync_Tree_Config>Yes</Network_Dect_Auto_Sync_Tree_Config>

Web Parameter

Auto configure DECT sync source tree

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Controls the ability to synchronize the multicell system.

- No—If the original primary base station can't be reached, the system continues without a primary to sync to.

- Yes—If the original primary base station can't be reached, another base station takes over as the primary base station.

Labels

Multi Cell

Network_Roaming_Deregister

Syntax Description

XML Tag Name

Network_Roaming_Deregister
Example:

<Network_Roaming_Deregister>No</Network_Roaming_Deregister>

Web Parameter

SIP Server support for multiple registrations per account

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Defines the method to handle SIP registration when a handset roams between base stations. Roam is the procedure when the handset moves its SIP and DECT registration between base stations. The roaming can initiate when the handset is idle.

This parameter appears if the 210 Multi-Cell Base Station is in the multicell system.

- No—The SIP registration of the handset deregisters from the current base station and registers to the new base station during roaming.

- Yes—The SIP registration of the handset remains on the current base station and also registers to the new base station during roaming.

Labels

Multi Cell

Network_Sntp_Broadcast_Enable

Syntax Description

XML Tag Name

Network_Sntp_Broadcast_Enable
Example:

<Network_Sntp_Broadcast_Enable>Yes</Network_Sntp_Broadcast_Enable>

Web Parameter

Allow broadcast NTP

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Identifies the use of the time server for all the devices.

Labels

Country

Network_Sync_Chain_Id

Syntax Description

XML Tag Name

Network_Sync_Chain_Id
Example:

<Network_Sync_Chain_Id>512</Network_Sync_Chain_Id>

Web Parameter

System chain ID

Default Value

512

Allowed Values

Integer

Units

Integer

Limits

0-4294967295 digits

User or Admin

Exposed in admin level

Description

Configures the Chain ID for dualcell system with DBS-110 or multicell system with DBS-210. Each base station in a dualcell or multicell system uses the same Chain ID.

Note

We recommend that you do not use a chain ID that is similar to an extension number.

Labels

Dual Cell or Multi Cell

Network_Sync_Data_Transport

Syntax Description

XML Tag Name

Network_Sync_Data_Transport
Example:

<Network_Sync_Data_Transport>0</Network_Sync_Data_Transport>

Web Parameter

Data Sync

Default Value

0

Allowed Values

- 0: Multicast

- 1: Peer-to-Peer

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the type of data synchronization.

- Multicast—Requires Multicast/IGMP to be enabled on the call control system.

- The multicast port range and IP addresses used is calculated from the chain ID.

- The multicast feature uses the port range: 49200 to 49999.

- The multicast feature IP range: 224.1.0.0 to 225.1.0.0.

- Multicast uses UDP.

- Peer-to-peer—Use this mode when the network doesn't allow Multicast. For multicast operation, enable the Multicast/IGMP on your switches. Otherwise, use Peer-to-peer mode.

Labels

Dual Cell or Multi Cell

Network_Sync_Debug_Enable

Syntax Description

XML Tag Name

Network_Sync_Debug_Enable
Example:

<Network_Sync_Debug_Enable>0</Network_Sync_Debug_Enable>

Web Parameter

Multi Cell debug

Default Value

0

Allowed Values

- 0: None

- 1: Data Sync

- 2: Auto Tree

- 3: Both

- 4: ieee1588 debug

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the level of multicell debugging information that stores in the logs.

- 0: None—No data

- 1: Data Sync—Writes header information for all packets received and sent to use to debug any special issues.

Note

This setting generates many logs. Use it for a short period of time when debugging.

- 2: Auto Tree—Writes states and data related to the Auto Tree Configuration feature.

- 3: Both—Both Data Sync and Auto Tree are enabled.

Note

This setting generates many logs. Use it for a short period of time when debugging.

- 4: ieee1588 debug—Use only when ieee LAN sync is enabled.

Labels

Multi Cell

Network_Sync_Enable

Syntax Description

XML Tag Name

Network_Sync_Enable
Example:

<Network_Sync_Enable>No</Network_Sync_Enable>

Web Parameter

Multi Cell system or Dual Cell system

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if the base station is part of a dualcell or multicell configuration.

Labels

Dual Cell or Multi Cell

Network_Sync_Max_Sip_Reg_Per_Base

Syntax Description

XML Tag Name

Network_Sync_Max_Sip_Reg_Per_Base
Example:

<Network_Sync_Max_Sip_Reg_Per_Base>08</Network_Sync_Max_Sip_Reg_Per_Base>

Web Parameter

Number of SIP accounts before distributed load

Default Value

08

Allowed Values

Integer

Units

Integer

Limits

4-30 digits

User or Admin

Exposed in admin level

Description

Defines when the base station attempts to distribute SIP registrations between the base stations in the chain. If this parameter is set to the value 8, this base station attempts to distribute SIP registrations to other base stations when it completes 8 SIP registrations.

Labels

Multi Cell

Network_Sync_Primary_Static_Ip

Syntax Description

XML Tag Name

Network_Sync_Primary_Static_Ip
Example:

<Network_Sync_Primary_Static_Ip>192.168.11.100</Network_Sync_Primary_Static_Ip>

Web Parameter

Primary Data Sync IP

Default Value

None

Allowed Values

IP address

Units

IP address

Limits

IP address

User or Admin

Exposed in admin level

Description

Indicates the base station data synchronization IP address.

When Data Sync is set to multicast, this base IP is selected automatically.

The data sync feature uses the port range of 49200 to 49999.

This option becomes available only if the parameter Network_Sync_Data_Transport is set to 1 (Peer-to-peer)

Labels

Dual Cell or Multi Cell

Network_Sync_Time

Syntax Description

XML Tag Name

Network_Sync_Time
Example:

<Network_Sync_Time>60</Network_Sync_Time>

Web Parameter

Synchronization time (s)

Default Value

60

Allowed Values

Integer

Units

Seconds

Limits

30-300

User or Admin

Exposed in admin level

Description

Indicates the period in seconds between synchronization requests by the base stations in the chain.

Labels

Multi Cell

Network_Vlan_Synchronization

Syntax Description

XML Tag Name

Network_Vlan_Synchronization
Example:

<Network_Vlan_Synchronization>Yes</Network_Vlan_Synchronization>

Web Parameter

Synchronization

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Specifies if each base station can apply the VLAN settings to other base stations. This parameter is specific to the base station and can't synchronize.

- Yes—All base stations use the same VLAN settings.

- No—Different VLAN settings on the base stations.

Labels

Network

Network_Wan_Dhcp_Option_Plug_And_Play

Syntax Description

XML Tag Name

Network_Wan_Dhcp_Option_Plug_And_Play
Example:

<Network_Wan_Dhcp_Option_Plug_And_Play>Yes</Network_Wan_Dhcp_Option_Plug_And_Play>

Web Parameter

Plug-n-Play

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if the base automatically receives PBX IP addresses under DHCP option 120.

- Yes—Enables DHCP plug and Play. This enables to store DHCP option 120 as SIP server.

- No—Disables DHCP plug and Play.

Labels

Network

Number_Of_Base_Stations

Syntax Description

XML Tag Name

Number_Of_Base_Stations
Example:

<Number_Of_Base_Stations>50</Number_Of_Base_Stations>

Web Parameter

System combination (Number of base stations/Repeaters per base station)

Default Value

50

Allowed Values

- 50

- 127

- 254

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

The three settings of base stations/repeaters per base station available are 50/3, 127/1, and 254/0.

Labels

Multi Cell

Off_Hook_Warning_Tone

Syntax Description

XML Tag Name

Off_Hook_Warning_Tone
Example:

<Off_Hook_Warning_Tone>480@10,620@0;10(.125/.125/1+2)
</Off_Hook_Warning_Tone>

Web Parameter

Off Hook Warning Tone

Default Value

480@10,620@0;10(.125/.125/1+2)

Allowed Values

String

Units

String

Limits

256 characters

User or Admin

Exposed in admin level

Description

Indicates the tone to play when the phone receiver is off hook after a period of time.

Labels

Call Progress Tones

Outbound_Proxy_n_

Syntax Description

XML Tag Name

Outbound_Proxy_n_
Example:

<Outbound_Proxy_1_>outboundproxy.com</Outbound_Proxy_1_>

Web Parameter

Outbound Proxy

Default Value

None

Allowed Values

Server URL

Units

URL

Limits

63 characters

User or Admin

Exposed in admin level

Description

Identifies the Session Border Controller or SIP server outbound proxy.

Set the outbound proxy to the address and port of the private NAT gateway, so that SIP messages are sent through the NAT gateway.

Labels

Servers

Page_Tone

Syntax Description

XML Tag Name

Page_Tone
Example:

<Page_Tone>600@-16;.3(.05/0.05/1)</Page_Tone>

Web Parameter

Page Tone

Default Value

600@-16;.3(.05/0.05/1)

Allowed Values

String

Units

String

Limits

256 characters

User or Admin

Exposed in admin level

Description

Indicates the tone to play to all handsets when the base station receive a page.

Labels

Call Progress Tones

Password_n_

Syntax Description

XML Tag Name

Password_n_

Example:

<Password_1_>Testpwd</Password_1_>

Web Parameter

Authentication Password

Default Value

None

Allowed Values

String

Units

String

Limits

128 characters

User or Admin

Exposed in admin level

Description

Identifies the user's password on the call control system.

Labels

Extensions > Add or Edit Extension

Phone_Name

Syntax Description

XML Tag Name

Phone_Name
Example:

<Phone_Name>abcdstation</Phone_Name>

Web Parameter

Base Station Name

Default Value

SME VoIP

Allowed Values

String

Units

String

Limits

35 characters

User or Admin

Exposed in admin level

Description

Indicates the name of the base station.

Labels

Management

Phonebook_Filename

Syntax Description

XML Tag Name

Phonebook_Filename

Example:

<Phonebook_Filename>abcphonebook</Phonebook_Filename>

Web Parameter

Filename

Default Value

None

Allowed Values

String

Units

String

Limits

31 characters

User or Admin

Exposed in admin level

Description

Identifies the name of the directory file on the server.

Labels

Central Directory

Phonebook_Location

Syntax Description

XML Tag Name

Phonebook_Location

Example:

<Phonebook_Location>192.168.10.11</Phonebook_Location>

Web Parameter

Server

Default Value

None

Allowed Values

IP address

Units

IP address

Limits

IP address

User or Admin

Exposed in admin level

Description

Identifies the server that contains the directory.

Labels

Central Directory

Phonebook_Reload_Time

Syntax Description

XML Tag Name

Phonebook_Reload_Time

Example:

<Phonebook_Reload_Time>250</Phonebook_Reload_Time>

Web Parameter

Phonebook reload interval(s)

Default Value

0

Allowed Values

Integer

Units

Seconds

Limits

0-4294967295

User or Admin

Exposed in admin level

Description

Controls how often the base station refreshes the phonebook contents in seconds. The refresh doesn't happen when the field is set to 0.

Specify a time that is frequent enough for the users but not so frequent that it overloads the base station.

Labels

Central Directory

Phonebook_Server_Location

Syntax Description

XML Tag Name

Phonebook_Server_Location

Example:

<Phonebook_Server_Location>0</Phonebook_Server_Location>

Web Parameter

Central Directory Location

Default Value

0

Allowed Values

- 0

- 1

- 2

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Identifies the type of central directory:

- 0: Local—Indicates the use of an imported comma separated value (CSV) file.

- 1: LDAP Server—Indicates the use of an LDAP directory.

- 2: XSI Server—Indicates the use of Broadworks Directory.

Labels

Central Directory

Pnp_Config

Syntax Description

XML Tag Name

Pnp_Config

Example:

<Pnp_Config>On</Pnp_Config>

Web Parameter

None

Default Value

On

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if a possible provider specific PnP registration feature is enabled.

Labels

None

Preferred_Codec_n_

Syntax Description

XML Tag Name

Preferred_Codec_n_

Example:

<Preferred_Codec_1_>G722</Preferred_Codec_1_>

Web Parameter

Codec Priority

Default Value

PCMU

Allowed Values

- PCMU

- PCMA

- G726

- G722

- G729

- OPUS

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Identifies the code priority that base stations use for audio compression and transmission. You can change the order of the codecs.

To get OPUS to display in the list, click Reset Codecs. If you change the list in any way, you must set the Reset Codecs and Reboot chain.

Labels

Servers

Primary_DNS

Syntax Description

XML Tag Name

Primary_DNS

Example:

<Primary_DNS>192.168.10.10</Primary_DNS>

Web Parameter

DNS (Primary)

Default Value

None

Allowed Values

IP address

Units

IP address

Limits

IP address

User or Admin

Exposed in admin level

Description

Indicates the use of IPv4 address of the main server for Domain Name System (DNS) queries.

This parameter is mandatory when you don't use DHCP.

Labels

Network

Primary_NTP_Server

Syntax Description

XML Tag Name

Primary_NTP_Server

Example:

<Primary_NTP_Server>192.168.10.28</Primary_NTP_Server>

Web Parameter

Time Server

Default Value

None

Allowed Values

IP Address

Units

IP Address

Limits

IP Address

User or Admin

Exposed in admin level

Description

Identifies the DNS name or the IP address of the network time server.

Note

Only IPv4 addresses are supported.

Labels

Country

Profile_Rule

Syntax Description

XML Tag Name

Profile_Rule

Example:

<Profile_Rule>https://ciscoserver.com</Profile_Rule>

Web Parameter

Configuration Server Address

Default Value

Empty

Allowed Values

Server URL

Units

URL

Limits

URL

User or Admin

Exposed in admin level

Description

Defines the profile URL.

Labels

Management

Promiscuous_button_enabled

Syntax Description

XML Tag Name

Promiscuous_button_enabled

Example:

<Promiscuous_button_enabled>No</Promiscuous_button_enabled>

Web Parameter

None

Default Value

None

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Allows you to reset the base station to factory defaults and then enable the promiscuous mode.

Labels

None

Promiscuous_mode

Syntax Description

XML Tag Name

Promiscuous_mode

Example:

<Promiscuous_mode>2</Promiscuous_mode>

Web Parameter

Enable in (min)

Default Value

None

Allowed Values

Integer

Units

Minutes

Limits

0-255 digits

User or Admin

Exposed in admin level

Description

Indicates the time for the base station in promiscuous mode.

Labels

Management

Prompt_Tone

Syntax Description

XML Tag Name

Prompt_Tone

Example:

<Prompt_Tone>520@-19,620@-19;10(*/0/1+2)</Prompt_Tone>

Web Parameter

Prompt Tone

Default Value

520@-19,620@-19;10(*/0/1+2)

Allowed Values

String

Units

String

Limits

256 characters

User or Admin

Exposed in admin level

Description

Prompts the user to enter a call forwarding phone number.

Labels

Call Progress Tones

Proxy_n_

Syntax Description

XML Tag Name

Proxy_n_

Example:

<Proxy_1_>192.168.10.11</Proxy_1_>

Web Parameter

Registrar

Default Value

None

Allowed Values

IP address

Units

IP address

Limits

IP address

User or Admin

Exposed in admin level

Description

Identifies the SIP Server (call control system) proxy server.

The port number in the address is optional.

Labels

Servers

PRT_http_header

Syntax Description

XML Tag Name

PRT_http_header

Example:

<PRT_http_header>Last-Modified</PRT_http_header>

Web Parameter

PRT Upload HTTP Header

Default Value

None

Allowed Values

String

Units

String

Limits

63 characters

User or Admin

Exposed in admin level

Description

Specifies a header for the HTTP upload request. This field is optional.

If you specify the header, you must specify a value in PRT_http_header_value.

Labels

Management

PRT_http_header_value

Syntax Description

XML Tag Name

PRT_http_header_value

Example:

<PRT_http_header_value>Mon, 6 Dec 2021 13:45:00 GMT</PRT_http_header_value>

Web Parameter

PRT Upload HTTP Header Value

Default Value

None

Allowed Values

String

Units

String

Limits

127 characters

User or Admin

Exposed in admin level

Description

Indicates the header field value for HTTP upload request. You must specify the header text in PRT_http_header.

Labels

Management

PRT_upload_filename

Syntax Description

XML Tag Name

PRT_upload_filename

Examples:

<PRT_upload_filename>Hello.tar.gz</PRT_upload_filename>

<PRT_upload_filename>Mac$MAC.tar.gz</PRT_upload_filename>

<PRT_upload_filename>path/path2/Mac$MAC.tar.gz</PRT_upload_filename>

Web Parameter

PRT Upload Filename

Default Value

None

Allowed Values

String

Units

String

Limits

64 characters

User or Admin

Exposed in admin level

Description

Indicates the problem report filename. The file extension is tar.gz.

Labels

Management

PRT_upload_server

Syntax Description

XML Tag Name

PRT_upload_server

Example:

<PRT_upload_server>https://ciscoprtserver.com:443</PRT_upload_server>

Web Parameter

PRT Upload Server

Default Value

Empty

Allowed Values

URL

Units

URL

Limits

127 characters

User or Admin

Exposed in admin level

Description

Indicates the target server to upload the problem report.

Labels

Management

Reg_Retry_Intvl_n_

Syntax Description

XML Tag Name

Reg_Retry_Intvl_n_

Example:

<Reg_Retry_Intvl_1_>30</Reg_Retry_Intvl_1_>

Web Parameter

Registration Retry Interval

Default Value

30

Allowed Values

Integer

Units

Seconds

Limits

0-4294967295 digits

User or Admin

Exposed in admin level

Description

Identifies the time in seconds to wait before the handset retries registration after a failed registration. Use this parameter when the registration failure message is Retry Reg RSC.

Labels

Servers

Reg_Retry_Intvl_High_Rnd

Syntax Description

XML Tag Name

Reg_Retry_Intvl_High_Rnd

Example:

<Reg_Retry_Intvl_High_Rnd>30</Reg_Retry_Intvl_High_Rnd>

Web Parameter

Registration Retry Interval High Rnd

Default Value

30

Allowed Values

Integer

Units

Integer

Limits

1-2147483

User or Admin

Exposed in admin level

Description

Indicates the high value of random interval to wait before registration retry after failing the last registration. If this value is greater than Reg_Retry_Intvl_n_, a random value between these two values is chosen.

Labels

Server

Reg_Retry_Long_Intvl_n_

Syntax Description

XML Tag Name

Reg_Retry_Long_Intvl_n_

Example:

<Reg_Retry_Long_Intvl_1_>1500</Reg_Retry_Long_Intvl_1_>

Web Parameter

Registration Retry Interval Long

Default Value

1200

Allowed Values

Integer

Units

Seconds

Limits

0-4294967295

User or Admin

Exposed in admin level

Description

Identifies the time in seconds to wait before the handset retries registration after a failed registration. Use this parameter when the registration failure message is something other than Retry Reg RSC.

If the field is set to 0, the handset doesn't retry the registration.

Set this parameter a larger interval than the value in Reg_Retry_Intvl_n_.

Labels

Servers

Reg_Retry_Long_Intvl_High_Rnd

Syntax Description

XML Tag Name

Reg_Retry_Long_Intvl_High_Rnd

Example:

<Reg_Retry_Long_Intvl_High_Rnd>1200</Reg_Retry_Long_Intvl_High_Rnd>

Web Parameter

Registration Retry Long Interval High Rnd

Default Value

1200

Allowed Values

Integer

Units

Integer

Limits

1-2147483

User or Admin

Exposed in admin level

Description

High value of random long interval to wait before registration long interval retry. If RegistrationRetry Long Interval High Rnd is greater than RegistrationRetry IntervalLong, then a random value between these two values is used. If the value is less than or equal to RegistrationRetry IntervalLong, then RegistrationRetry IntervalLong is used.

Labels

Server

Register_Expires_n_

Syntax Description

XML Tag Name

Register_Expires_n_

Example:

<Register_Expires_1_>4000</Register_Expires_1_>

Web Parameter

Reregistration time (s)

Default Value

3600

Allowed Values

Integer

Units

Seconds

Limits

0-65535

User or Admin

Exposed in admin level

Description

Indicates the time in seconds for a valid SIP registration and represents the maximum time between SIP registrations for the SIP account.

We recommend that you don't set this below 60 seconds.

Labels

Servers

Reorder_Tone

Syntax Description

XML Tag Name

Reorder_Tone

Example:

<Reorder_Tone>480@-19,620@-19;10(.25/.25/1+2)</Reorder_Tone>

Web Parameter

Reorder Tone

Default Value

480@-19,620@-19;10(.25/.25/1+2)

Allowed Values

String

Units

String

Limits

256 characters

User or Admin

Exposed in admin level

Description

Plays when an outbound call fails or after the far end hangs up during an established call. Reorder Tone plays automatically when Dial Tone or any of its alternatives times out.

Labels

Call Progress Tones

Repeater_Auto_Config_Mode_n_

Syntax Description

XML Tag Name

Repeater_Auto_Config_Mode_n_

Example:

<Repeater_Auto_Config_Mode_1_>1</Repeater_Auto_Config_Mode_1_>

Web Parameter

DECT sync mode

Default Value

1

Allowed Values

- 0: Manual

- 1: Local Automatically

- 2: Chaining Automatically

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the type of synchronisation with the base station.

- 0: Manual—Manually specify REPEATER_RPN and REPEATER_SYNC_SRC_RPN.

- 1: Local Automatically—Repeater searches for available base stations and automatically locate the nearest base station. If a base station is turned off, the repeater tries to locate another available base station. The settings REPEATER_RPN and REPEATER_SYNC_SRC_RPN are ignored.

- 2: Chaining Automatically—All base stations and repeaters send a RSSI report to the primary base station. The primary base station uses the report to create a new DECT synchronization tree with all the selected base stations and repeaters to use this setting.

Labels

Repeaters

Repeater_Data_Configured_n_

Syntax Description

XML Tag Name

Repeater_Data_Configured_n_

Example:

<Repeater_Data_Configured_1_>Yes</Repeater_Data_Configured_1_>

Web Parameter

State

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the state of the repeater.

- No—The repeater isn't configured to communicate with the base.

- Yes—The repeater is configured to communicate with the base.

Labels

Repeater

Repeater_Dect_Ipui_n_

Syntax Description

XML Tag Name

Repeater_Dect_Ipui_n_

Example:

<Repeater_Dect_Ipui_1_>0xAABB1212FF</Repeater_Dect_Ipui_1_>

Web Parameter

None

Default Value

0xFFFFFFFFFF

Allowed Values

Hexadecimal

Units

Hexadecimal

Limits

12 characters

User or Admin

Exposed in admin level

Description

Indicates the repeater International Portable User Identity (IPUI). You can't configure the IPUI with provisioning. You can specify the IPUI as HEX strings containing 10 HEX values available in the repeater status menu.

You can provision without 0x in the value.

Note

A IPEI/IPUI value must be available only once in the configuration file.

Labels

None

Repeater_Name_n_

Syntax Description

XML Tag Name

Repeater_Name_n_

Example:

<Repeater_Name_1_>Repeatername</Repeater_Name_1_>

Web Parameter

Name

Default Value

None

Allowed Values

String

Units

String

Limits

19 characters

User or Admin

Exposed in admin level

Description

Identifies the repeater name. You might want to set the name to a location.

Labels

Repeaters > Add or Edit Repeaters

Repeater_Rpn_n_

Syntax Description

XML Tag Name

Repeater_Rpn_n_

Example:

<Repeater_Rpn_1_>0x00</Repeater_Rpn_1_>

<Repeater_Rpn_2_>0x01</Repeater_Rpn_2_>

Web Parameter

None

Default Value

0x00

Allowed Values

- 0x00

- 0x01

- 0x02

- 0x03

Units

Hexadecimal

Limits

0-255

User or Admin

Exposed in admin level

Description

Use this parameter when Repeater_Auto_Config_Mode is set to manual.

You can specify a unique RPN value with the parameter Repeater_Sync_Src_Rpn for each repeater.

The repeaters use only the number of bits of the RPNs 8 bits for this parameter. The number of bits that repeater RPN uses is 2.

You must configure all the repeaters that use manual mode to use unique RPN.

The RPN value 0x00 of the base station is invalid.

Labels

None

Repeater_Sync_Src_Rpn_n_

Syntax Description

XML Tag Name

Repeater_Sync_Src_Rpn_n_

Example:

<Repeater_Sync_Src_Rpn_1_>0x00</Repeater_Sync_Src_Rpn_1_>

Web Parameter

None

Default Value

0x00

Allowed Values

Hexadecimal

Units

Hexadecimal

Limits

1–252 digits

User or Admin

Exposed in admin level

Description

Use this parameter when Repeater_Auto_Config_Mode is set to manual.

You can specify a unique RPN value with the parameter REPEATER_RPN for each repeater.

The maximum chain length is 3 repeaters in the chain for a base Station.

You must configure all the repeaters which use the manual mode to use unique RPN.

RPN 0x01 to 0x03 uses the base station in NETWORK_SYNC_MAC_CHAIN index 0 as the DECT synchronization source. RPN 0x04 to 0x06 uses the base station in NETWORK_SYNC_MAC_CHAIN index 1 as the DECT synchronization source.

Labels

None

Resync_At_HHmm_

Syntax Description

XML Tag Name

Resync_At_HHmm_

Example:

<Resync_At_HHmm_>14:05</Resync_At_HHmm_>

Web Parameter

Auto Resync Time

Default Value

00:00

Allowed Values

String

Units

hh:mm format

Limits

23:59

User or Admin

Exposed in admin level

Description

Indicates the time (24-hour clock) that the base station looks to resync the configuration file.

The value is in the format 00h00 in French and Spanish configuration files.

Labels

Management

Resync_At_Random_Delay

Syntax Description

XML Tag Name

Resync_At_Random_Delay

Example:

<Resync_At_Random_Delay>20</Resync_At_Random_Delay>

Web Parameter

Auto Resync Max Delay (Min)

Default Value

15

Allowed Values

Integer

Units

Seconds

Limits

0-1439

User or Admin

Exposed in admin level

Description

Indicates the time delay, in seconds. Set different delay times for each base station to prevent them from asking for new configuration files at the same time.

Use this parameter with Auto_Resync_Time, Auto_Resync_Polling, Auto_Resync_Periodic, Auto_Resync_Days.

Labels

Management

Resync_Periodic

Syntax Description

XML Tag Name

Resync_Periodic

Example:

<Resync_Periodic>500</Resync_Periodic>

Web Parameter

Auto Resync Periodic (Min)

Default Value

0

Allowed Values

Integer

Units

Minutes

Limits

0-65535

User or Admin

Exposed in admin level

Description

Indicates the resync time in minutes.

Use this parameter with Auto_Resync_Time, Auto_Resync_Polling, Auto_Resync_Delay, and Auto_Resync_Days.

Labels

Management

Resync_Polling

Syntax Description

XML Tag Name

Resync_Polling

Example:

<Resync_Polling>Off</Resync_Polling>

Web Parameter

Auto Resync Polling

Default Value

Off

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Controls the ability to look for new configuration files for the automatic synchronization. If the value is On, automatic sync is enabled.

Use this parameter with Auto_Resync_Time, Auto_Resync_Periodic, Auto_Resync_Delay, Auto_Resync_Days, and Auto resync configuration polling.

Labels

Management

Retry_Reg_RSC_n_

Syntax Description

XML Tag Name

Retry_Reg_RSC_n_

Example:

<Retry_Reg_RSC_1_>5??,6??</Retry_Reg_RSC_1_>

Web Parameter

Registration Retry RSC

Default Value

None

Allowed Values

String

Units

String

Limits

15 characters

User or Admin

Exposed in admin level

Description

Identifies the Response SIP Code (RSC) that triggers a retry. You can set up to 4 comma-delimited values and use the wild card character (?).

If SIP response code to a register attempt matches this filter, it uses SRV_SIP_REGISTER_RETRY_INTERVAL. Otherwise, it uses SRV_SIP_REGISTER_RETRY_LONG_INTERVAL.

Labels

Servers

Reversed_Auth_Realm_n_

Syntax Description

XML Tag Name

Reversed_Auth_Realm_n_

Example:

<Reversed_Auth_Realm_4_>Broadworks</Reversed_Auth_Realm_4_>

Web Parameter

Reversed Auth Realm

Default Value

None

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the IP address for an authentication realm other than the proxy IP address.

Labels

Servers

Reverse_Phone_Lookup_Serv

Syntax Description

XML Tag Name

Reverse_Phone_Lookup_Serv

Example:

<Reverse_Phone_Lookup_Serv>No</Reverse_Phone_Lookup_Serv>

Web Parameter

None

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level.

Description

- Yes: Enabled—If you define a central directory, the lookup in central directory is done.

- No: Disabled— If you define a central directory, the lookup in central directory isn't done.

Labels

None

RFC_2543_Call_Hold_n_

Syntax Description

XML Tag Name

RFC_2543_Call_Hold_n_

Example:

<RFC_2543_Call_Hold_n_>Yes</RFC_2543_Call_Hold_n_>

Web Parameter

Hold Behaviour

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the way hold works on the handset.

- Yes—The connection information part of the SDP is set to 0.0.0.0, and based on the context the direction attribute is send only, recvonly, or inactive.

- No—Behaves according to RFC 3264. The connection information part of the SDP contains the IP address of the endpoint, and based on the context the direction attribute is send only, recvonly, or inactive.

Labels

Servers

Ring_Back_Tone

Syntax Description

XML Tag Name

Ring_Back_Tone

Example:

<Ring_Back_Tone>440@-19,480@-19;*(2/4/1+2)</Ring_Back_Tone>

Web Parameter

Ring Back Tone

Default Value

440@-19,480@-19;*(2/4/1+2)

Allowed Values

String

Units

String

Limits

256 characters

User or Admin

Exposed in admin level

Description

Indicates the tone that plays during an outbound call when the far end is ringing.

Labels

Call Progress Tones

Rsx_Trace_Internal

Syntax Description

XML Tag Name

Rsx_Trace_Internal

Example:

<Rsx_Trace_Internal>0</Rsx_Trace_Internal>

Web Parameter

RSX internal tracing

Default Value

0

Allowed Values

- 0: Disabled

- 1: Enabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if internal tracing is Disabled or Enabled. You can enable this parameter for debugging.

Labels

Diagnostics

Rtp_Collision_Control

Syntax Description

XML Tag Name

Rtp_Collision_Control

Example:

<Rtp_Collision_Control>Enabled</Rtp_Collision_Control>

Web Parameter

RTP Collision Detection

Default Value

Enabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Allows to enable or disable RTP collision control.

- Enabled—The device accepts all sources.

- Disabled—When two sources have the same SSRC, the second source is discarded.

Labels

Network

RTP_Packet_Size_n_

Syntax Description

XML Tag Name

RTP_Packet_Size_n_

Example:

<RTP_Packet_Size_1_>0.020</RTP_Packet_Size_1_>

Web Parameter

RTP Packet Size

Default Value

0.020

Allowed Values

- 0.020

- 0.040

- 0.060

- 0.080

Units

ms

Limits

0.020-0.080

User or Admin

Exposed in admin level

Description

Indicates the preferred RTP packet size when the packet size is negotiated.

Labels

Servers

RTP_Port_Max

Syntax Description

XML Tag Name

RTP_Port_Max

Example:

<RTP_Port_Max>16423</RTP_Port_Max>

Web Parameter

RTP Port Range

Default Value

16423

Allowed Values

Integer

Units

Integer

Limits

0-65280 digits

User or Admin

Exposed in admin level

Description

Indicates the number of ports to use for RTP audio streaming.

Labels

Network

RTP_Port_Min

Syntax Description

XML Tag Name

RTP_Port_Min

Example:

<RTP_Port_Min>16384</RTP_Port_Min>

Web Parameter

RTP port

Default Value

16384

Allowed Values

Integer

Units

Integer

Limits

0-65280

User or Admin

Exposed in admin level

Description

Indicates the first RTP port to use for RTP audio streaming.

Labels

Network

RTP_TOS_DiffServ_Value

Syntax Description

XML Tag Name

RTP_TOS_DiffServ_Value

Example:

<RTP_TOS_DiffServ_Value>0xb8</RTP_TOS_DiffServ_Value>

Web Parameter

RTP ToS/QoS

Default Value

0xb8

Allowed Values

Hexadecimal

Units

Hexadecimal

Limits

0-254

User or Admin

Exposed in admin level

Description

Indicates the priority of RTP traffic, based on the IP layer Type of Service (ToS) byte.

- Bits 7–5 define precedence

- Bits 4–2 define ToS

- Bits 1–0 are ignored

Note

The cost bit is not supported.

Labels

Network

Second_Preferred_Codec_n_

Syntax Description

XML Tag Name

Second_Preferred_Codec_n_

Example:

<Second_Preferred_Codec_1_>G722</Second_Preferred_Codec_1_>

Web Parameter

Codec Priority
Max number of codecs is 5

Default Value

G722

Allowed Values

- PCMU

- PCMA

- G726

- G722

- G729

- OPUS

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Identifies the code priority that base stations use for audio compression and transmission. You can change the order of the codecs.

Labels

Servers

Secondary_DNS

Syntax Description

XML Tag Name

Secondary_DNS

Example:

<Secondary_DNS>192.168.10.11</Secondary_DNS>

Web Parameter

DNS (Secondaries)

Default Value

None

Allowed Values

IP address

Units

IP address

Limits

IP address

User or Admin

Exposed in admin level

Description

Indicates the alternate DNS server.

You must enable DHCP to change this parameter.

Labels

Network

Secure_Call_Option_n_

Syntax Description

XML Tag Name

Secure_Call_Option_n_

Example:

<Secure_Call_Option_1_>Disabled</Secure_Call_Option_1_>

Web Parameter

Secure RTP

Default Value

Disabled

Allowed Values

- Disabled

- Enabled

- Optional

- Auto

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if RTP streams are encrypted.

- Disabled—Indicates that the RTP stream isn't encrypted. The SRTP is disabled and the calls that require SRTP are rejected.

- Enabled—Indicates that the RTP stream is encrypted. The calls that don't support SRTP are rejected.

- Optional—Indicates that the RTP encryption is optional. The SDP contains AVP and SAVP profiles. Both the SRTP supported and not supported calls are accepted.

- Auto—The media security defines if the protocol is RTP or SRTP.

Labels

Servers

Secure_Call_Setting_n_

Syntax Description

XML Tag Name

Secure_Call_Setting_n_

Example:

<Secure_Call_Setting_1_>Yes</Secure_Call_Setting_1_>

Web Parameter

Secure RTP Auth

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if secure RTP uses authentication of RTP packets. When enabled, a base can support a maximum of 4 concurrent calls.

- Yes: Enabled—Authentication is enabled in SRTP stream.

- No: Disabled—Authentication is disabled in SRTP stream.

Labels

Servers

Server_ID_n_

Syntax Description

XML Tag Name

Server_ID_n_

Example:

<Server_ID_1_>1</Server_ID_1_>

Web Parameter

Server

Default Value

1

Allowed Values

Integer

Units

Integer

Limits

1-10 digits

User or Admin

Exposed in admin level

Description

Identifies the SIP server address of the call control system.

Labels

Extensions > Add or Edit Extension

Share_Call_Appearance_n_

Syntax Description

XML Tag Name

Share_Call_Appearance_n_

Example:

<Share_Call_Appearance_1_>Private</Share_Call_Appearance_1_>

Web Parameter

BroadWorks Shared Call Appearance

Default Value

Private

Allowed Values

- Private

- Shared

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Identifies if the line is shared.

Only applicable to BroadSoft SIP servers. Must be enabled on the SIP server. If the value is Private, the extension isn't part of a shared call appearance.

Labels

Extensions > Add or Edit Extension

SIP_100REL_Enable_n_

Syntax Description

XML Tag Name

SIP_100REL_Enable_n_

Example:

<SIP_100REL_Enable_1_>Yes</SIP_100REL_Enable_1_>

Web Parameter

Supported 100rel

Default Value

Yes

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Allows to add a supported header that contains 100rel to the SIP message when you send an outgoing INVITE request. The base station supports PRACK requests. If the value is Yes, it allows to add 100rel in Supported header in the outgoing INVITE SIP request.

Labels

Servers

Sip_Check_Sync_Always_Reboot

Syntax Description

XML Tag Name

Sip_Check_Sync_Always_Reboot

Example:

<Sip_Check_Sync_Always_Reboot>On</Sip_Check_Sync_Always_Reboot>

Web Parameter

Always Reboot On Check-Sync

Default Value

Disabled

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if the base station reboots when a NOTIFY of the type check-sync is sent to the base station.

Labels

Network

Sip_Failover_Reconnect_Timer

Syntax Description

XML Tag Name

Sip_Failover_Reconnect_Timer

Example:

<Sip_Failover_Reconnect_Timer>60</Sip_Failover_Reconnect_Timer>

Web Parameter

Failover Reconnect Timer

Default Value

60

Allowed Values

Integer

Units

Seconds

Limits

0-4294967

User or Admin

Exposed in admin level

Description

Controls the delay, in seconds, between queries from the base station to locate the primary server during failover.

Labels

Network

SIP_Outbound_Proxy_Mode

Syntax Description

XML Tag Name

SIP_Outbound_Proxy_Mode
Example:

<SIP_Outbound_Proxy_Mode>0</SIP_Outbound_Proxy_Mode>

Web Parameter

Outbound Proxy Mode

Default Value

0

Allowed Values

- 0: Use Always

- 1: Only use Outbound Proxy for initial SIP requests

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the outbound proxy use.

- 0: Use always—All outbound calls as sent to the outbound proxy.

- 1: Only use Outbound Proxy for initial SIP requests—Only use the outbound proxy for initial SIP requests.

Labels

Network

SIP_Port

Syntax Description

XML Tag Name

SIP_Port

Example:

<SIP_Port>5060</SIP_Port>

Web Parameter

Local SIP Port

Default Value

5060

Allowed Values

Integer

Units

Integer

Limits

0-65280 digits

User or Admin

Exposed in admin level

Description

Indicates the SIP signaling source port.

Labels

Network

Sip_Reject_Anonymous_Calls_Enabled_n

Syntax Description

XML Tag Name

Sip_Reject_Anonymous_Calls_Enabled_n

Example:

<Sip_Reject_Anonymous_Calls_Enabled_1>Disabled
</Sip_Reject_Anonymous_Calls_Enabled_1>

Web Parameter

Reject Anonymous Calls

Default Value

Disabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if the handset should reject calls that don't have a caller ID.

Labels

Extensions > Add or Edit Extension

Sip_Stun_Bindtime_Determine

Syntax Description

XML Tag Name

Sip_Stun_Bindtime_Determine

Example:

<Sip_Stun_Bindtime_Determine>On</Sip_Stun_Bindtime_Determine>

Web Parameter

STUN Bindtime Determine

Default Value

On

Allowed Values

- On

- Yes

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

If STUN is enabled and you define SIP_STUN_BINDTIME_GUARD, setting this parameter to On forces the system to automatically determine the duration of NAT bindings in the system. The SIP_STUN_BINDTIME_GUARD parameter defines the initial test duration.

Labels

Network

Sip_Stun_Bindtime_Guard

Syntax Description

XML Tag Name

Sip_Stun_Bindtime_Guard

Example:

<Sip_Stun_Bindtime_Guard>80</Sip_Stun_Bindtime_Guard>

Web Parameter

STUN Bindtime Guard

Default Value

80

Allowed Values

Integer

Units

Seconds

Limits

0-65535

User or Admin

Exposed in admin level

Description

Identifies the lifetime of the STUN binding.

Labels

Network

Sip_Timer_B

Syntax Description

XML Tag Name

Sip_Timer_B

Example:

<Sip_Timer_B>5</Sip_Timer_B>

Web Parameter

Failover SIP timer B

Default Value

5

Allowed Values

Integer

Units

Seconds

Limits

0-4294967

User or Admin

Exposed in admin level

Description

Indicates the time to wait for a response from an INVITE message from the SIP server before failover is triggered.

Labels

Network

Sip_Timer_F

Syntax Description

XML Tag Name

Sip_Timer_F

Example:

<Sip_Timer_F>5</Sip_Timer_F>

Web Parameter

Failover SIP Timer F

Default Value

5

Allowed Values

Integer

Units

Seconds

Limits

0-4294967

User or Admin

Exposed in admin level

Description

Indicates the time to wait for a response from an non-INVITE message from the SIP server before failover is triggered.

Labels

Network

SIP_TOS_DiffServ_value

Syntax Description

XML Tag Name

SIP_TOS_DiffServ_value
Example:

<SIP_TOS_DiffServ_value>0x68</SIP_TOS_DiffServ_value>

Web Parameter

SIP ToS/QoS

Default Value

0x68

Allowed Values

Hexadecimal

Units

Hexadecimal

Limits

0–254

User or Admin

Exposed in admin level

Description

Indicates the priority of call control signaling traffic that is based on the IP layer Type of Service (ToS) byte. ToS is the same as Quality of Service (QoS) in packet-based networks.

- Bits 7–5 defines precedence

- Bits 4–2 defines Type of Service

- Bits 1–0 are ignored

Note

The cost bit isn't supported.

Labels

Network

SIP_Transport_n_

Syntax Description

XML Tag Name

SIP_Transport_n_
Example:

<SIP_Transport_1_>UDP</SIP_Transport_1_>

Web Parameter

SIP Transport

Default Value

UDP

Allowed Values

- UDP

- TCP

- TLS

- Auto

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the protocol for SIP transport.

- UDP— Enforce the use of SIP over UDP.

- TCP—Enforce the use of SIP over TCP.

- TLS—Enforce the use of TLS over TCP.

- Auto—A NAPTR lookup must succeed. The order (normally TLS, TCP, UDP) of the entries from the DNS NAPTR lookup is taken into account. TLS, TCP, and UDP are all accepted. SCTP is not accepted.

Labels

Servers

Sip_Use_Different_Ports

Syntax Description

XML Tag Name

Sip_Use_Different_Ports

Example:

<Sip_Use_Different_Ports>Disabled</Sip_Use_Different_Ports>

Web Parameter

Use Different SIP Ports

Default Value

Disabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates SIP signaling ports.

- Disabled—The Local SIP Port field specifies the source port used for SIP signaling in the system.

- Enabled—The Local SIP Port field specifies the source port used for the first user agent (UA) instance. Succeeding UAs get successive ports.

Set this field to Enabled for single-base systems.

Labels

Network

Src_Att_Transfer_2nd_call_On_Hold_1_

Syntax Description

XML Tag Name

Src_Att_Transfer_2nd_call_On_Hold_n_
Example:

<Src_Att_Transfer_2nd_call_On_Hold_1_>1</Src_Att_Transfer_2nd_call_On_Hold_1_>

Web Parameter

Attended Transfer Behaviour

Default Value

1

Allowed Values

- 0: Disabled

- 1: Enabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if the second call is put on hold during an attended transfer.

Labels

Servers

Srv_Codec_Enable_G729ab_n_

Syntax Description

XML Tag Name

Srv_Codec_Enable_G729ab_n_
Example:

<Srv_Codec_Enable_G729ab_1_>Disabled</Srv_Codec_Enable_G729ab_1_>

Web Parameter

G729 Annex B

Default Value

Disabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the use of G729 Annex B. If the value is Enabled, it uses G729 Annex B.

Labels

Servers

Srv_Enable_No_Sip_Registration_n_

Syntax Description

XML Tag Name

Srv_Enable_No_Sip_Registration_n_
Example:

<Srv_Enable_No_Sip_Registration_1_>No</Srv_Enable_No_Sip_Registration_1_>

Web Parameter

None

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Defines if the base station should enable the SIP registration by default. If the value is set to No, it allows the extension to register during SIP registration. If the value is set to Yes, it doesn't allow the extension to register during SIP registration.

You can still make and receive calls.

Labels

None

Srv_Failback_Before_Failover_n_

Syntax Description

XML Tag Name

Srv_Failback_Before_Failover_n_

Example:

<Srv_Failback_Before_Failover_1_>yes</Srv_Failback_Before_Failover_1_>

Web Parameter

Failback before Failover

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Options without units

User or Admin

Exposed in admin level

Description

Indicates failback to the primary server instead of failover to the next server.

Labels

Server

Srv_Failback_de_register_n_

Syntax Description

XML Tag Name

Srv_Failback_de_register_n_
Example:

<Srv_Failback_de_register_1_>No</Srv_Failback_de_register_1_>

Web Parameter

Deregister After Failback

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Defines if the given extension should or shouldn't de-register at the previous server when failover to the primary SIP server.

No: Don't de-register at the previous server

Yes: De-register at the previous server

Labels

Servers

Srv_Remote_Ringtone_n_

Syntax Description

XML Tag Name

Srv_Remote_Ringtone_n_
Example:

<Srv_Remote_Ringtone_1_>Enabled</Srv_Remote_Ringtone_1_>

Web Parameter

Remote Ring Tone Control

Default Value

Enabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates to enable or disable the remote ringtone control (alert tone) sent to the handset.

Labels

Servers

Srv_Sip_Enable_Ptime_n_

Syntax Description

XML Tag Name

Srv_Sip_Enable_Ptime_n_
Example:

<Srv_Sip_Enable_Ptime_1_>Enabled</Srv_Sip_Enable_Ptime_1_>

Web Parameter

Use ptime

Default Value

Enabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if the ptime and maxptime in the Session Description Protocol (SDP) is enabled or disabled.

Labels

Servers

Srv_Sip_Enable_Rtcp_n_

Syntax Description

XML Tag Name

Srv_Sip_Enable_Rtcp_n_
Example:

<Srv_Sip_Enable_Rtcp_1_>Enabled</Srv_Sip_Enable_Rtcp_1_>

Web Parameter

RTCP

Default Value

Enabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the use of RTCP in SDP.

Labels

Servers

Srv_Sip_Keep_Alive_n_

Syntax Description

XML Tag Name

Srv_Sip_Keep_Alive_n_
Example:

<Srv_Sip_Keep_Alive_1_>Enabled</Srv_Sip_Keep_Alive_1_>

Web Parameter

Keep Alive

Default Value

Enabled

Allowed Values

- Enabled

- Diabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates to send the SIP keep alive packets. The keep alive packets keep the SIP channel open and send the packets as SIP requests. If you define a proxy server address, these packets are sent to this server. Otherwise, the packets are sent to the registered address.

Labels

Servers

Srv_Sip_Ringback_Tone_n_

Syntax Description

XML Tag Name

Srv_Sip_Ringback_Tone_n_
Example:

<Srv_Sip_Ringback_Tone_1_>Enabled</Srv_Sip_Ringback_Tone_1_>

Web Parameter

Local Ring Back Tone

Default Value

Enabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates to use the ring back tone. If the value is Enabled, the handset generates the ring tone locally.

Labels

Servers

Srv_Sip_Rtp_Base_Equal_n_

Syntax Description

XML Tag Name

Srv_Sip_Rtp_Base_Equal_n_
Example:

<Srv_Sip_Rtp_Base_Equal_1_>Disabled</Srv_Sip_Rtp_Base_Equal_1_>

Web Parameter

RTP from own base station

Default Value

Disabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the base station which initiates the RTP traffic.

- Enabled—Starts the RTP Stream from the base station where the SIP registration is sent.

- Disabled—Starts the RTP Stream from the base station where the handset is currently present.

Labels

Servers

Srv_Sip_Server_Alias_n_

Syntax Description

XML Tag Name

Srv_Sip_Server_Alias_n_
Example:

<Srv_Sip_Server_Alias_1_>testservr</Srv_Sip_Server_Alias_1_>

Web Parameter

Server Alias

Default Value

None

Allowed Values

String

Units

String

Limits

10 characters

User or Admin

Exposed in admin level

Description

Identifies the short name for the call control server.

Labels

Servers

Srv_Sip_Show_Ext_Name_In_Hs_n_

Syntax Description

XML Tag Name

Srv_Sip_Show_Ext_Name_In_Hs_n_
Example:

<Srv_Sip_Show_Ext_Name_In_Hs_1_>Enabled</Srv_Sip_Show_Ext_Name_In_Hs_1_>

Web Parameter

Show Extension on Handset Idle Screen

Default Value

Enabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if the handset idle screen displays the extension.

Labels

Servers

Srv_Sip_Signal_Tcp_Port_n_

Syntax Description

XML Tag Name

Srv_Sip_Signal_Tcp_Port_n_
Example:

<Srv_Sip_Signal_Tcp_Port_1_>Enabled</Srv_Sip_Signal_Tcp_Port_1_>

Web Parameter

Signal TCP Source Port

Default Value

Enabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates to signal the source TCP port in the SIP messages when set to TCP or TLS. You may need to change this parameter based on the given SIP PBX.

Labels

Servers

Srv_SRTP_Auth_n_

Syntax Description

XML Tag Name

Srv_SRTP_Auth_n_
Example:

<Srv_SRTP_Auth_1_>Disabled</Srv_SRTP_Auth_1_>

Web Parameter

Secure RTP

Default Value

Disabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if the RTP streams are encrypted. If the value is set to Enabled, the authentication is enabled in the SRTP stream.

Labels

Servers

Static_IP

Syntax Description

XML Tag Name

Static_IP
Example:

<Static_IP>192.168.10.25</Static_IP>

Web Parameter

IP Address

Default Value

None

Allowed Values

IP address

Units

IP address

Limits

IP address

User or Admin

Exposed in admin level

Description

Indicates the IPv4 address of the device. You can change this value, if DHCP is disabled.

Labels

Network

STUN_Enable

Syntax Description

XML Tag Name

STUN_Enable
Example:

<STUN_Enable>No</STUN_Enable>

Web Parameter

Enable STUN

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the use of RFC3489 Session Traversal UDP for NAT (STUN). If the value is No, STUN is disabled.

Labels

Network

STUN_Server

Syntax Description

XML Tag Name

STUN_Server
Example:

<STUN_Server>192.168.10.15</STUN_Server>

Web Parameter

STUN Server

Default Value

None

Allowed Values

IP address

Units

IP address

Limits

IP address

User or Admin

Exposed in admin level

Description

Identifies the location of the STUN server.

Labels

Network

Subcsr_Call_Group_Subscribed_

Syntax Description

XML Tag Name

Subcsr_Call_Group_Subscribed_

Example:

<Subcsr_Call_Group_Subscribed_>2</Subcsr_Call_Group_Subscribed_>

Web Parameter

Call Group(s)

Default Value

Fill(0x00000000)

Allowed Values

Integer

Units

Integer

Limits

32bit (one bit per call group bytes) for one handset up to 1000 handsets

User or Admin

Exposed in admin/user level

Description

Indicates the call group ID.

Labels

Terminal

Subscr_Dect_Ac_Code_n_

Syntax Description

XML Tag Name

Subscr_Dect_Ac_Code_n_

Where, n is the handset number.

Example:

<Subscr_Dect_Ac_Code_1_>1111</Subscr_Dect_Ac_Code_1_>

Web Parameter

AC

Default Value

FFFF

Allowed Values

String

Units

String

Limits

4 or 6 digits

User or Admin

Exposed in admin level

Description

Assigns individual access code to each handset.

Labels

Extensions

Subscr_Dect_Ipui_n_

Syntax Description

XML Tag Name

Subscr_Dect_Ipui_n_
Example:

<Subscr_Dect_Ipui_1_>0xFFFFFFFFFF</Subscr_Dect_Ipui_1_>

Web Parameter

IPEI

Default Value

0xFFFFFFFFFF

Allowed Values

Hexadecimal

Units

Hexadecimal

Limits

None

User or Admin

Exposed in admin level

Description

Identifies the International Portable Equipment Identity (IPEI) of the handset. The IPEI isn't used with provisioning.

If you enable FEATURE_IPEI_CONTROLLED_DECT_REG, you can specify the handset IPEI as HEX string that contains all 10 HEX values of the IPEI available on the handset status menu.

The IPEI/IPUI value must be present only once in the configuration file.

When you register a handset to a base station, the entry to specify IPEI for the handset should be open for registration.

Labels

Terminal

Subscr_Do_Not_Disturb_Enabled_n_

Syntax Description

XML Tag Name

Subscr_Do_Not_Disturb_Enabled_n_
Example:

<Subscr_Do_Not_Disturb_Enabled_1_>Disabled</Subscr_Do_Not_Disturb_Enabled_1_>

Web Parameter

Do Not Disturb

Default Value

Disabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if do not disturb option is enabled in the base station regardless of the setting in the handset.

Labels

Extensions > Add or Edit Extension

Subscr_Hebu_Password_n_

Syntax Description

XML Tag Name

Subscr_Hebu_Password_n_

Where n is the handset index. The index can be 1–980 for 210 Multi-Cell Base Station and 1–30 for 110 Single-Cell Base Station.

Example:

<Subscr_Hebu_Password_1_>Testpwd1@</Subscr_Hebu_Password_1_>

Web Parameter

HEBU Password

Default Value

0x254

Allowed Values

String

Units

String

Limits

40 characters

User or Admin

Exposed in admin level

Description

Indicates the password for the handset registration in the HEBU mode.

Labels

Terminal

Subscr_Hebu_Username_n_

Syntax Description

XML Tag Name

Subscr_Hebu_Username_n_

Where n is the handset index. The index can be 1–980 for 210 Multi-Cell Base Station and 1–20 for 110 Single-Cell Base Station.

Example:

<Subscr_Hebu_Username_1_>Abcd</Subscr_Hebu_Username_1_>

Web Parameter

HEBU Username

Default Value

None

Allowed Values

String

Units

String

Limits

40 characters

User or Admin

Exposed in admin level

Description

Indicates the username for the handset registration in HEBU mode.

Labels

Terminal

Subscr_Hide_Number_Enabled_n_

Syntax Description

XML Tag Name

Subscr_Hide_Number_Enabled_n_
Example:

<Subscr_Hide_Number_Enabled_1_>Disabled</Subscr_Hide_Number_Enabled_1_>

Web Parameter

Hide Number

Default Value

Disabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates that the base station hides the number regardless of the setting in the handset.

Labels

Extensions > Add or Edit Extension

Subscr_Intercom_Enabled_

Syntax Description

XML Tag Name

Subscr_Intercom_Enabled_

Example:

<Subscr_Intercom_Enabled_>Disabled</Subscr_Intercom_Enabled_>

Web Parameter

Intercom

Default Value

Disabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Options without units

User or Admin

Exposed in admin/user level

Description

Indicates if the intercom is enabled for the handsets.

Labels

Terminal

Subscr_Sip_Hs_Idx_n_

Syntax Description

XML Tag Name

Subscr_Sip_Hs_Idx_n_

Example:

<Subscr_Dect_Ipui_1_>0x1231231234</Subscr_Dect_Ipui_1_>
<Subscr_Sip_Hs_Idx_1_>1</Subscr_Sip_Hs_Idx_1_>
<User_ID_1_>4081001000</User_ID_1_>
<Subscr_Dect_Ipui_2_>0xFFFFFFFFFF</Subscr_Dect_Ipui_2_>
<Subscr_Sip_Hs_Idx_2_>1</Subscr_Sip_Hs_Idx_2_>
<User_ID_2_>4081002000</User_ID_2_>

Web Parameter

Idx

Default Value

n

Allowed Values

Integer

Units

Integer

Limits

1–1000

User or Admin

Exposed in admin level

Description

Handset ID association for an extension.

Labels

Extensions

Subscr_Sip_Pincode_Dialout_n_

Syntax Description

XML Tag Name

Subscr_Sip_Pincode_Dialout_n_
Example:

<Subscr_Sip_Pincode_Dialout_1_>1234*</Subscr_Sip_Pincode_Dialout_1_>

Web Parameter

None

Default Value

None

Allowed Values

Integer and special characters * and #

Units

Integer and special characters * and #

Limits

0-8 digits

User or Admin

Exposed in admin level

Description

Indicates the pin code to use for outgoing call.

Labels

None

Subscr_Sip_Reject_Anonymous_Calls_Enabled_n_

Syntax Description

XML Tag Name

Subscr_Sip_Reject_Anonymous_Calls_Enabled_n_
Example:

<Subscr_Sip_Reject_Anonymous_Calls_Enabled_1_>Disabled
</Subscr_Sip_Reject_Anonymous_Calls_Enabled_1_>

Web Parameter

Reject anonymous calls

Default Value

Disabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if the handset should reject calls that don't have a caller ID.

Labels

Extensions > Add or Edit Extension

Subscr_Sip_Ua_Use_Base_n_

Syntax Description

XML Tag Name

Subscr_Sip_Ua_Use_Base_n_
Example:

<Subscr_Sip_Ua_Use_Base_1_>0xFF</Subscr_Sip_Ua_Use_Base_1_>

Web Parameter

None

Default Value

0xFF

Allowed Values

- 0xFF: Not locked

- RPN value: Locked to a specific base

Units

Hexadecimal

Limits

0–255

User or Admin

Exposed in admin level

Description

Indicates that the account is locked to use one base station. The value 0xFF means Not Locked.
Each base in a multicell system has an RPN value. This value is available on the Multicell web page of the base station.

Labels

None

Subscr_Ua_Data_Bw_Sca_Info_Mapping_n_

Syntax Description

XML Tag Name

Subscr_Ua_Data_Bw_Sca_Info_Mapping_n_

Example:

<Subscr_Ua_Data_Bw_Sca_Info_Mapping_1_>1, 1, 1, 1, 5, 5, 5, 5</Subscr_Ua_Data_Bw_Sca_Info_Mapping_1_>

Web Parameter

Shared Call Appearance Settings

Default Value

65535, 65535, 65535, 65535, 65535, 65535, 65535, 65535

Allowed Values

Integers entered 8 times separated by comma. Each integer can be 1-8 or 65535.

Units

Integer

Limits

1-8 or 65535

User or Admin

Exposed in admin level

Description

Allows you to store the mapping of SCA information icons to extension IDs.

The extensions must be a part of a SCA. Each byte is one SCA information icon on the handset display. Byte 0 is the first icon from the left, byte 1 is the second icon, and so on. If byte is 0, an extension isn't mapped to the corresponding icon. Several bytes that have the same value mean that the corresponding icons monitor different call appearances on the same shared line.

Labels

Terminal

Subscr_Ua_Data_Emergency_Line_n_

Syntax Description

XML Tag Name

Subscr_Ua_Data_Emergency_Line_n_

Example:

<Subscr_Ua_Data_Emergency_Line_1_>0xFFFF</Subscr_Ua_Data_Emergency_Line_1_>

Web Parameter

Alarm Line

Default Value

0xFFFF

Allowed Values

Hexadecimal

Units

Hexadecimal

Limits

0–65535

User or Admin

Exposed in admin level

Description

Indicates the index of the extension which dials the emergency number when you use the alarm button on the handset.

Labels

Terminal

Subscr_Ua_Data_Emergency_Profiles_n_

Syntax Description

XML Tag Name

Subscr_Ua_Data_Emergency_Profiles_n_

Example:

<Subscr_Ua_Data_Emergency_Profiles_1_>0x0</Subscr_Ua_Data_Emergency_Profiles_1_>

Web Parameter

Profile 0 to 7

Default Value

0x0

Allowed Values

Hexadecimal

Units

Hexadecimal

Limits

0–128 digits

User or Admin

Exposed in admin level

Description

The bit map which contains the profiles that the handset uses. There is 1 bit for each profile 0–7. You can only provision these values: 0, 1, 2, 4, 8, 16, 32, 64, 128.

Labels

Terminal

Syslog_Server

Syntax Description

XML Tag Name

Syslog_Server

Example:

<Syslog_Server>10.10.100.100:514</Syslog_Server>

Web Parameter

Syslog Server IP Address

Default Value

None

Allowed Values

IP address

Units

IP address

Limits

IP address

User or Admin

Exposed in admin level

Description

Indicates the address of the Syslog server.

Labels

Management

Syslog_Transport

Syntax Description

XML Tag Name

Syslog_Transport

Example:

<Syslog_Transport>0</Syslog_Transport>

Web Parameter

TLS security

Default Value

0

Allowed Values

- 0

- 1

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Defines if syslog connection should use secure TLS during login.

- 0—Uses UDP

- 1—Uses TCP with TLS

Labels

Management

Tcp_Keep_Alive_Interval

Syntax Description

XML Tag Name

Tcp_Keep_Alive_Interval

Example:

<Tcp_Keep_Alive_Interval>75</Tcp_Keep_Alive_Interval>

Web Parameter

TCP Keep Alive Interval

Default Value

75

Allowed Values

Integer

Units

Seconds

Limits

0-4294967295

User or Admin

Exposed in admin level

Description

Identifies the length of time, in seconds, that the client waits before it sends a keep-alive message on a TCP connection.

Labels

Network

Text_Msg_Keep_Alive

Syntax Description

XML Tag Name

Text_Msg_Keep_Alive

Example:

<Text_Msg_Keep_Alive>30</Text_Msg_Keep_Alive>

Web Parameter

Text Messaging Keep Alive (m)

Default Value

30

Allowed Values

Integer

Units

Minutes

Limits

0-65535

User or Admin

Exposed in admin level

Description

Indicates the frequency of keep alive messages in minutes.

Labels

Management

Text_Msg_Mode

Syntax Description

XML Tag Name

Text_Msg_Mode

Example:

<Text_Msg_Mode>0</Text_Msg_Mode>

Web Parameter

Text Messaging

Default Value

0

Allowed Values

- 0: Disabled

- 1: Enabled

- 2: Enabled without Server

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates if users can send text messages to other devices that support text messages.

- 0: Disabled—Users can't send text messages.

- 1: Enabled—Users can send text messages to anyone. This requires the rest of the fields in this area to be set.

- 2: Enabled without Server—Users can only send text messages to other members of the system.

Labels

Management

Text_Msg_Port

Syntax Description

XML Tag Name

Text_Msg_Port

Example:

<Text_Msg_Port>1300</Text_Msg_Port>

Web Parameter

Text Messaging Port

Default Value

1300

Allowed Values

Integer

Units

Integer

Limits

0-65535

User or Admin

Exposed in admin level

Description

Indicates the Messaging and Alarm server port used for messages. Set the port to allow users to exchange text messages with people outside your system. The value of this field depends on the message server.

If you leave this field empty, users can only communicate inside the system.

Labels

Management

Text_Msg_Response_Time

Syntax Description

XML Tag Name

Text_Msg_Response_Time

Example:

<Text_Msg_Response_Time>45</Text_Msg_Response_Time>

Web Parameter

Text Messaging Response

Default Value

30

Allowed Values

Integer

Units

Seconds

Limits

0-255

User or Admin

Exposed in admin level

Description

Indicates the timeout if the system doesn't receive a response from the message server.

Labels

Management

Text_Msg_Server

Syntax Description

XML Tag Name

Text_Msg_Server

Example:

<Text_Msg_Server>192.168.10.25</Text_Msg_Server>

Web Parameter

Text Messaging & Alarm Server

Default Value

None

Allowed Values

IP address

Units

IP address

Limits

IP address

User or Admin

Exposed in admin level

Description

Indicates the IP address or URL of the Messaging and Alarm server. Set the address to allow users to exchange text messages with people outside your system.

If you leave this field empty, users can only communicate inside the system.

Labels

Management

Text_Msg_Ttl

Syntax Description

XML Tag Name

Text_Msg_Ttl

Example:

<Text_Msg_Ttl>0</Text_Msg_Ttl>

Web Parameter

Text Messaging TTL

Default Value

0

Allowed Values

Integer

Units

Seconds

Limits

0-65535

User or Admin

Exposed in admin level

Description

Indicates the text message time to live (TTL) in seconds. If set, the message only displays for the configured amount of time. After that time, the message is automatically deleted.

The default value 0 means the message doesn't expire.

Labels

Management

Third_Preferred_Codec_n_

Syntax Description

XML Tag Name

Third_Preferred_Codec_n_

Example:

<Third_Preferred_Codec_1_>G726</Third_Preferred_Codec_1_>

Web Parameter

Codec Priority
Max number of codecs is 5

Default Value

None

Allowed Values

- PCMU

- PCMA

- G726

- G722

- G729

- OPUS

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Identifies the code priority that base stations use for audio compression and transmission. You can change the order of the codecs.

To get OPUS to display in the list, click Reset Codecs.

If you change the list in any way, you must press Reset Codecs on this page and Reboot chain on the Multi cell page.

Labels

Servers

Upgrade Rule (Base Station)

Syntax Description

XML Tag Name

Upgrade Rule

Example:

<Upgrade Rule>http://server.com/ DBS-210-3PC-03-24-18-0000-58.fwu</Upgrade Rule>

Web Parameter

Firmware Update Settings

Default Value

None

Allowed Values

URL

Units

URL

Limits

URL

User or Admin

Exposed in admin level

Description

Indicates the URL pointing to the base station firmware.

Labels

Firmware Update

Upgrade Rule (Handset)

Syntax Description

XML Tag Name

Upgrade_Rule_HS

Example:

<Upgrade_Rule_HS>http://server.com/6825-RGD_v0324_b1708.fwu</Upgrade_Rule_HS>

Web Parameter

Firmware Update Settings

Default Value

None

Allowed Values

URL

Units

URL

Limits

URL

User or Admin

Exposed in admin level

Description

Indicates the URL that points to the handset firmware. This parameter can appear three times in the configuration, each for 6823 handset, 6825 handset, and 6825 ruggedized handset.

Labels

Firmware Update

Upgrade_Rule_RPT (Repeater)

Syntax Description

XML Tag Name

Upgrade_Rule_RPT

Example:

<Upgrade_Rule_RPT>http://server.com/RPT110-3PC-03-24-18-0000-58.fwu
</Upgrade_Rule_RPT>

Web Parameter

Firmware Update Settings

Default Value

None

Allowed Values

URL

Units

URL

Limits

URL

User or Admin

Exposed in admin level

Description

Indicates the URL points to the repeater firmware.

Labels

Firmware Update

Use_One_Tcp_Conn_Per_Ext_n_

Syntax Description

XML Tag Name

Use_One_Tcp_Conn_Per_Ext_n_

Example:

<Use_One_Tcp_Conn_Per_Ext_1_>No</Use_One_Tcp_Conn_Per_Ext_1_>

Web Parameter

Use One TCP Connection per SIP Extension

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the use of TCP or TLS connections.

When the SIP transport is TCP or TLS, there are two choices for the connections:

- Disabled—Each base station has a single TCP or TLS connection that the handsets share.

- Enabled—Each line has an individual TCP or TLS connection.

Note

You should set this field to Enabled to handle multiple responses to a NAPTR or SRV lookup.

Labels

Servers

Use_Pref_Codec_Only_n_

Syntax Description

XML Tag Name

Use_Pref_Codec_Only_n_

Example:

<Use_Pref_Codec_Only_1_>No</Use_Pref_Codec_Only_1_>

Web Parameter

Use Own Codec Priority

Default Value

No

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the codec priority for incoming calls.

- Disabled—Uses the calling party priority.

- Enabled—Uses the system codec priority.

For example, if enabled and the base has G722 as the top codec and the calling party has Alaw on top and G722 further down the list, the G722 codec is chosen for the call.

Labels

Servers

User_ID_n_

Syntax Description

XML Tag Name

User_ID_n_

Example:

<User_ID_1_>750</User_ID_1_>

Web Parameter

Extension Info

Default Value

N/A

Allowed Values

String

Units

String

Limits

35 characters

User or Admin

Exposed in admin level

Description

The handset extension information.

Labels

Extensions

User_Password

Syntax Description

XML Tag Name

User_Password

Example:

<User_Password>Testuserpwd4@</User_Password>

Web Parameter

User Password

Default Value

String up to 8 characters

Allowed Values

String

Units

String

Limits

128 characters

User or Admin

Exposed in admin level

Description

Indicates the user password to access the web pages.

Labels

Security

VLAN_ID

Syntax Description

XML Tag Name

VLAN_ID

Example:

<VLAN_ID>0</VLAN_ID>

Web Parameter

ID

Default Value

0

Allowed Values

Integer

Units

Integer

Limits

0-4094

User or Admin

Exposed in admin level

Description

Identifies the 802.1Q VLAN.

Labels

Network

Vlan_QoS

Syntax Description

XML Tag Name

Vlan_QoS

Example:

<Vlan_QoS>0</Vlan_QoS>

Web Parameter

User Priority

Default Value

0

Allowed Values

Integer

Units

Integer

Limits

0-7

User or Admin

Exposed in admin level

Description

Defines the user priority. Use these values to prioritize different classes of traffic (voice, video, data).

- 0—best effort

- 1—lowest priority

- 7—highest priority

Labels

Network

Voice_Mail_Number_n_

Syntax Description

XML Tag Name

Voice_Mail_Number_n_

Example:

<Voice_Mail_Number_1_>2177707717</Voice_Mail_Number_1_>

Web Parameter

Mailbox Number

Default Value

None

Allowed Values

String

Units

String

Limits

20 characters

User or Admin

Exposed in admin level

Description

Identifies the number for the handset to dial the voicemail system. This number should be enabled on the SIP server. Leave the value empty if the number isn't used for voice mail.

Labels

Extensions > Add or Edit Extension

Voip_Sip_Auto_Upload

Syntax Description

XML Tag Name

Voip_Sip_Auto_Upload

Example:

<Voip_Sip_Auto_Upload>Disabled</Voip_Sip_Auto_Upload>

Web Parameter

Upload of SIP Log

Default Value

Disabled

Allowed Values

- Enabled

- Disabled

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Configures the automatic upload of SIP log files. If the value is Enabled, the SIP log uploads to syslog server.

Labels

Management

Web_Language

Syntax Description

XML Tag Name

Web_Language

Example:

<Web_Language>English</Web_Language>

Web Parameter

Select Language

Default Value

English

Allowed Values

List of languages

- English

- Español

- Deutsch

- Francais

- Italiano

- Dutch

- Português

- Dansk

- Svenska

- Turkce

- Polski

- Russian

- Norsk

- Slovenian

- Cestina

- Hrvatski

- Srpski

- Magyar

Units

Options without units

Limits

Option

User or Admin

Exposed in admin and user level

Description

Identifies the language for the base station web pages.

Labels

Country

Web_Min_Pass_Len

Syntax Description

XML Tag Name

Web_Min_Pass_Len

Example:

<Web_Min_Pass_Len>12345678</Web_Min_Pass_Len>

Web Parameter

Minimum length (min 8)

Default Value

8 digits

Allowed Values

Integer

Units

Integer

Limits

4–127 digits

User or Admin

Exposed in admin level

Description

Defines the minimum password length to access the web pages.

Labels

Security

Web_Pass_Constraint_To_Ascii

Syntax Description

XML Tag Name

Web_Pass_Constraint_To_Ascii

Example:

<Web_Pass_Constraint_To_Ascii>0</ Web_Pass_Constraint_To_Ascii>

Web Parameter

Only ASCII characters

Default Value

0

Allowed Values

0 or 1

Units

Options without units

Limits

Option

User or Admin

Exposed in admin level

Description

Indicates the use of characters in the password to access the web pages.

The value 1 allows to use only ASCII characters.

Labels

Security

XSI_Host_Server

Syntax Description

XML Tag Name

XSI_Host_Server

Example:

<XSI_Host_Server>192.168.11.102</XSI_Host_Server>

Web Parameter

Server

Default Value

None

Allowed Values

IP Address

Units

IP Address

Limits

IP Address

User or Admin

Exposed in admin level

Description

Indicates the name or IP address (including the path) of a server to retrieve an XSI server.

Labels

Central Directory

Chapter 3. XML Tags for Handset Settings

This section provides information about XML tags used for handset settings.

- Hs_Admin_Pin_n_

- Hs_Alarm_n_

- Hs_Alert_Tone_n_

- Hs_Alert_Vol_n_

- Hs_Auto_Answer_n_

- Hs_Auto_Keylock_n_

- Hs_Bluetooth_n_

- Hs_Charger_Warn_n_

- Hs_Confirm_Sound_n_

- Hs_Coverage_Warn_n_

- Hs_Hide_Number_n_

- Hs_Idle_Clock_n_

- Hs_Idle_Screen_n_

- Hs_Key_Sound_n_

- Hs_Led_Green_n_

- Hs_Led_Orange_n_

- Hs_Led_Red_n_

- Hs_Line_n_

- Hs_Msg_Display_n_

- Hs_Msg_Overwrite_Old_n_

- Hs_Msg_Send_n_

- Hs_Name_n_

- Hs_Phone_Lock_n_

- Hs_Power_Save_n_

- Hs_Ptt_n_

- Hs_Rec_Alarm_Enable_n_

- Hs_Rec_Alarm_n_

- Hs_Ring_Emerg_High_n_

- Hs_Ring_Emerg_Low_n_

- Hs_Ring_Emerg_Mid_n_

- Hs_Ring_Mel_n_

- Hs_Ring_Norm_Msg_n_

- Hs_Ring_Urgent_Msg_n_

- Hs_Ring_Vol_n_

- Hs_Select_Network_n_

- Hs_Silent_Charging_n_

- Hs_Silent_n_

- Hs_Unlock_Pin_n_

- Hs_Vibrate_n_

Hs_Admin_Pin_n_

Syntax Description

XML Tag Name

Hs_Admin_Pin_n_

Example:

<Hs_Admin_Pin_1_>1234</Hs_Admin_Pin_1_>

Default Value

0000

Allowed Values

Integer

Units

Integer

Limits

4 digits

Description

Allows to change the admin PIN to unlock the handset.

Handset Menu

Settings > Security > Change admin PIN

Hs_Alarm_n_

Syntax Description

XML Tag Name

Hs_Alarm_n_

Example:

<Hs_Alarm_1_>05:30</Hs_Alarm_1_>

Default Value

Empty

Allowed Values

hh:mm

Units

Hour:minutes

Limits

00-23:00-59

Description

Defines the alarm time.

Handset Menu

Alarms > Alarm

Hs_Alert_Tone_n_

Syntax Description

XML Tag Name

Hs_Alert_Tone_n_

Example:

<Hs_Alert_Tone_1_>1</Hs_Alert_Tone_1_>

Default Value

1

Allowed Values

- 0: Ringer

- 1: Sunrise

- 2: Vibes

- 3: Reflections

- 4: Calculation

- 5: Loud ringer

Units

Integer

Limits

Options 1-5

Description

Specifies the ring tone for alert calls.

Handset Menu

Settings > Audio Settings > Alert tone

Hs_Alert_Vol_n_

Syntax Description

XML Tag Name

Hs_Alert_Vol_n_

Example:

<Hs_Alert_Vol_1_>1234</Hs_Alert_Vol_1_>

Default Value

3

Allowed Values

0–6

Units

Integer

Limits

0–6

Description

Specifies volume of the tone when you press Emergency button on the handset.

Note

This setting isn't supported in 6823 Handset.

Handset Menu

Settings > Audio settings > Alert volume

Hs_Auto_Answer_n_

Syntax Description

XML Tag Name

Hs_Auto_Answer_n_

Example:

<Hs_Auto_Answer_1_>1234</Hs_Auto_Answer_1_>

Default Value

0

Allowed Values

- 0: Normal

- 1: Any key

- 2: Automatic

Units

Options without units

Limits

Option

Description

Defines the way the handset handles incoming calls

Handset Menu

Settings > Auto answer

Hs_Auto_Keylock_n_

Syntax Description

XML Tag Name

Hs_Auto_Keylock_n_

Example:

<Hs_Auto_Keylock_1_>On</Hs_Auto_Keylock_1_>

Default Value

Off

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

Description

Defines the handset to lock the keypad after the specified length of inactivity.

Handset Menu

Settings > Security > Automatic keylock

Hs_Bluetooth_n_

Syntax Description

XML Tag Name

Hs_Bluetooth_n_

Example:

<Hs_Bluetooth_1_>On</Hs_Bluetooth_1_>

Default Value

Off

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

Description

Allows to enable or disable the use of Bluetooth® headset.

Handset Menu

Settings > Bluetooth > Enable/disable

Hs_Charger_Warn_n_

Syntax Description

XML Tag Name

Hs_Charger_Warn_n_

Example:

<Hs_Charger_Warn_1_>On</Hs_Charger_Warn_1_>

Default Value

On

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

Description

Allows the handset to play a tone when you put the handset on the charger.

Handset Menu

Settings > Audio settings > Charger warning

Hs_Confirm_Sound_n_

Syntax Description

XML Tag Name

Hs_Confirm_Sound_n_

Example:

<Hs_Confirm_Sound_1_>On</Hs_Confirm_Sound_1_>

Default Value

On

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

Description

Indicates to play a tone when you change a setting on the handset.

Handset Menu

Settings > Audio Settings > Confirmation sound

Hs_Coverage_Warn_n_

Syntax Description

XML Tag Name

Hs_Coverage_Warn_n_

Example:

<Hs_Coverage_Warn_1_>Off</Hs_Coverage_Warn_1_>

Default Value

Off

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

Description

Indicates the handset to give you a tone when the signal from the base station or repeater becomes too weak.

Handset Menu

Settings > Audio settings > Coverage warning

Hs_Hide_Number_n_

Syntax Description

XML Tag Name

Hs_Hide_Number_n_

Example:

<Hs_Hide_Number_1_>0</Hs_Hide_Number_1_>

Default Value

0

Allowed Values

- 0: Off

- 1: On for next call

- 2: Always on

Units

Options without units

Limits

Option

Description

Indicates if the handset can make a call without the Caller ID for the next call or for all calls.

Handset Menu

Settings > Hide Number

Hs_Idle_Clock_n_

Syntax Description

XML Tag Name

Hs_Idle_Clock_n_

Example:

<Hs_Idle_Clock_1_>On</Hs_Idle_Clock_1_>

Default Value

On

Allowed Values

- Yes

- No

Units

Options without units

Limits

Option

Description

Indicates if the time displays on the home screen when the handset is idle.

Handset Menu

Settings > Idle Clock

Hs_Idle_Screen_n_

Syntax Description

XML Tag Name

Hs_Idle_Screen_n_

Example:

<Hs_Idle_Screen_1_>Off</Hs_Idle_Screen_1_>

Default Value

0

Allowed Values

- 0: Off

- 1: Idle clock (dimmed)

- 2: Startup image (dimmed)

Units

Options without units

Limits

Option

Description

Indicates the screen display when the handset is in the charger.

Handset Menu

Settings > Idle Screen Saver

Hs_Key_Sound_n_

Syntax Description

XML Tag Name

Hs_Key_Sound_n_

Example:

<Hs_Key_Sound_1_>0</Hs_Key_Sound_1_>

Default Value

0

Allowed Values

- 0: Silent

- 1: Click

- 2: Tone

Units

Options without units

Limits

Option

Description

Indicates the sound you hear when you press a key on your handset.

Handset Menu

Settings > Audio settings > Key sound

Hs_Led_Green_n_

Syntax Description

XML Tag Name

Hs_Led_Green_n_

Example:

<Hs_Led_Green_1_>2</Hs_Led_Green_1_>

Default Value

2

Allowed Values

- 0: Off

- 1: Missed call

- 2: Voice message

- 3: Low battery

Units

Options without units

Limits

Option

Description

Indicates the LED color at the top of the handset for the defined option.

Handset Menu

Settings > LED signal > Green LED

Hs_Led_Orange_n_

Syntax Description

XML Tag Name

Hs_Led_Orange_n_

Example:

<Hs_Led_Orange_1_>3</Hs_Led_Orange_1_>

Default Value

3

Allowed Values

- 0: Off

- 1: Missed call

- 2: Voice message

- 3: Low battery

Units

Options without units

Limits

Option

Description

Indicates the LED color at the top of the handset for the defined option.

Handset Menu

Settings > LED signal > Orange LED

Hs_Led_Red_n_

Syntax Description

XML Tag Name

Hs_Led_Red_n_

Example:

<Hs_Led_Red_1_>1</Hs_Led_Red_1_>

Default Value

1

Allowed Values

- 0: Off

- 1: Missed call

- 2: Voice message

- 3: Low battery

Units

Options without units

Limits

Option

Description

Indicates the LED color at the top of the handset for the defined option.

Handset Menu

Settings > LED signal > Red LED

Hs_Line_n_

Syntax Description

XML Tag Name

Hs_Line_n_

Example:

<Hs_Line_1_>65</Hs_Line_1_>

Default Value

0

Allowed Values

Integer

Units

Integer

Limits

0-19

Description

Indicates the primary line, if you have multiple lines.

Handset Menu

Settings > Line

Hs_Msg_Display_n_

Syntax Description

XML Tag Name

Hs_Msg_Display_n_

Example:

<Hs_Msg_Display_1_>On</Hs_Msg_Display_1_>

Default Value

On

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

Description

Defines the display of a new message when your handset is idle. When you receive a new message, you can set the handset to:

- Display only that you have a new message.

- Display the full message immediately. This is the default setting.

Handset Menu

Messaging > Settings > Display

Hs_Msg_Overwrite_Old_n_

Syntax Description

XML Tag Name

Hs_Msg_Overwrite_Old_n_

Example:

<Hs_Msg_Overwrite_Old_1_>Off</Hs_Msg_Overwrite_Old_1_>

Default Value

Off

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

Description

Indicates to overwrite old messages when the text message history reaches the limit.

You can keep up to 250 messages. If you don't enable the handset to overwrite old messages, you have to manually delete messages when the text message history is full.

Handset Menu

Messaging > Settings > Overwrite old

Hs_Msg_Send_n_

Syntax Description

XML Tag Name

Hs_Msg_Send_n_

Example:

<Hs_Msg_Send_1_>On</Hs_Msg_Send_1_>

Default Value

On

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

Description

Indicates to save the messages you send in the text message history. By default, your sent messages are saved in the text message history.

Handset Menu

Messaging > Settings > Sent Messages

Hs_Name_n_

Syntax Description

XML Tag Name

Hs_Name_n_

Example:

<Hs_Name_1_>Handset9</Hs_Name_1_>

Default Value

Empty

Allowed Values

String

Units

String

Limits

20 characters

Description

Defines the name to display on the main screen of the handset.

Handset Menu

Settings > Handset name

Hs_Phone_Lock_n_

Syntax Description

XML Tag Name

Hs_Phone_Lock_n_

Example:

<Hs_Phone_Lock_1_>Off</Hs_Phone_Lock_1_>

Default Value

Off

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

Description

Allows to set up a PIN to unlock the handset.

Handset Menu

Security > Phone lock

Hs_Power_Save_n_

Syntax Description

XML Tag Name

Hs_Power_Save_n_

Example:

<Hs_Power_Save_1_>5</Hs_Power_Save_1_>

Default Value

5

Allowed Values

- 0: 5 seconds

- 1: 10 seconds

- 2: 20 seconds

- 3: 30 seconds

- 4: 45 seconds

- 5: 60 seconds

Units

Options without units

Limits

Option

Description

Defines the time to turn off the handset screen.

Handset Menu

Settings > Power save

Hs_Ptt_n_

Syntax Description

XML Tag Name

Hs_Ptt_n_

Example:

<Hs_Ptt_1_>Off</Hs_Ptt_1_>

Default Value

Off

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

Description

Allows to use the handset as a two-way radio to talk with other active handsets in the system.

Handset Menu

Settings > Push to Talk

Hs_Rec_Alarm_Enable_n_

Syntax Description

XML Tag Name

Hs_Rec_Alarm_Enable_n_

Example:

<Hs_Rec_Alarm_Enable_1_>On</Hs_Rec_Alarm_Enable_1_>

Default Value

Off

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

Description

Allows to set the alarm time for the defined days of the week.

Handset Menu

Alarms > Recurrent alarm

Hs_Rec_Alarm_n_

Syntax Description

XML Tag Name

Hs_Rec_Alarm_Enable_n_

Example:

<Hs_Rec_Alarm_Enable_1_>12:45:1100101</Hs_Rec_Alarm_Enable_1_>

Default Value

None

Allowed Values

HH:MM

HH:MM:ddddddd, where, ddddddd is the day of the week

Units

Hour:minutes:day of the week

Limits

00-23:00-59

00-23:00-59:0000000-1111111

Description

Indicates the time that your handset reminds you at a specific time each day with a recurrent alarm timer. You can set only one recurrent alarm on the handset

Handset Menu

Alarms > Recurrent alarm

Hs_Ring_Emerg_High_n_

Syntax Description

XML Tag Name

Hs_Ring_Emerg_High_n_

Example:

<Hs_Ring_Emerg_High_1_>5</Hs_Ring_Emerg_High_1_>

Default Value

3

Allowed Values

- 0: Ringer

- 1: Sunrise

- 2: Vibes

- 3: Reflections

- 4: Calculation

- 5: Loud ringer

Units

Options without units

Limits

Option

Description

Defines the ring tone for high emergency calls.

Handset Menu

Settings > Audio settings > Ring emerg. high

Hs_Ring_Emerg_Low_n_

Syntax Description

XML Tag Name

Hs_Ring_Emerg_Low_n_

Example:

<Hs_Ring_Emerg_High_1_>2</Hs_Ring_Emerg_High_1_>

Default Value

3

Allowed Values

- 0: Ringer

- 1: Sunrise

- 2: Vibes

- 3: Reflections

- 4: Calculation

- 5: Loud ringer

Units

Options without units

Limits

Option

Description

Defines the ring tone for low emergency calls.

Handset Menu

Settings > Audio settings > Ring emerg. low

Hs_Ring_Emerg_Mid_n_

Syntax Description

XML Tag Name

Hs_Ring_Emerg_Mid_n_

Example:

<Hs_Ring_Emerg_Mid_1_>4</Hs_Ring_Emerg_Mid_1_>

Default Value

3

Allowed Values

- 0: Ringer

- 1: Sunrise

- 2: Vibes

- 3: Reflections

- 4: Calculation

- 5: Loud ringer

Units

Options without units

Limits

Option

Description

Defines the ring tone for medium emergency calls.

Handset Menu

Settings > Audio settings > Ring emerg. med

Hs_Ring_Mel_n_

Syntax Description

XML Tag Name

Hs_Ring_Mel_n_

Example:

<Hs_Ring_Mel_1_>0</Hs_Ring_Mel_1_>

Default Value

0

Allowed Values

- 0: Ringer

- 1: Sunrise

- 2: Vibes

- 3: Reflections

- 4: Calculation

- 5: Loud ringer

Units

Options without units

Limits

Option

Description

Defines the ring tone for normal calls.

Handset Menu

Settings > Audio settings > Ring melody

Hs_Ring_Norm_Msg_n_

Syntax Description

XML Tag Name

Hs_Ring_Norm_Msg_n_

Example:

<Hs_Ring_Norm_Msg_1_>4</Hs_Ring_Norm_Msg_1_>

Default Value

4

Allowed Values

- 0: Ringer

- 1: Sunrise

- 2: Vibes

- 3: Reflections

- 4: Calculation

- 5: Loud ringer

Units

Options without units

Limits

Option

Description

Defines the ring tone for normal messages.

Handset Menu

Settings > Audio settings > Ring normal msg.

Hs_Ring_Urgent_Msg_n_

Syntax Description

XML Tag Name

Hs_Ring_Urgent_Msg_n_

Example:

<Hs_Ring_Urgent_Msg_1_>4</Hs_Ring_Urgent_Msg_1_>

Default Value

4

Allowed Values

- 0: Ringer

- 1: Sunrise

- 2: Vibes

- 3: Reflections

- 4: Calculation

- 5: Loud ringer

Units

Options without units

Limits

Option

Description

Defines the ring tone for urgent messages.

Handset Menu

Settings > Audio settings > Ring urgent msg.

Hs_Ring_Vol_n_

Syntax Description

XML Tag Name

Hs_Ring_Vol_n_

Example:

<Hs_Ring_Vol_1_>4</Hs_Ring_Vol_1_>

Default Value

3

Allowed Values

0-6

Units

Integer

Limits

Integer

Description

Allows to change the volume of the ringer. This volume does not impact the volume level when you are on a call.

Handset Menu

Settings > Audio settings > Ring volume

Hs_Select_Network_n_

Syntax Description

XML Tag Name

Hs_Select_Network_n_

Example:

<Hs_Select_Network_1_>72</Hs_Select_Network_1_>

Default Value

3

Allowed Values

- 0: Auto select

- 1-20: Registration number in list

Units

Options without units

Limits

Option

Description

Allows to select the network.

Handset Menu

Connectivity > Select network

Hs_Silent_Charging_n_

Syntax Description

XML Tag Name

Hs_Silent_Charging_n_

Example:

<Hs_Silent_Charging_1_>0</Hs_Silent_Charging_1_>

Default Value

0

Allowed Values

- 0: Off

- 1: Silent

Units

Options without units

Limits

Option

Description

Allows to turn off the ringer if you don't want the handset to ring while it is charging. Incoming calls continue to display on the screen.

Handset Menu

Settings > Silent charging

Hs_Silent_n_

Syntax Description

XML Tag Name

Hs_Silent_n_

Example:

<Hs_Silent_1_>Off</Hs_Silent_1_>

Default Value

Off

Allowed Values

- On

- Off

Units

Options without units

Limits

Option

Description

Allows to stop the handset from ringing where there is an incoming call.

When the handset is in silent mode, incoming calls display on the screen, but the handset does not play a ringtone.

Handset Menu

Settings > Audio settings > Silent

Hs_Unlock_Pin_n_

Syntax Description

XML Tag Name

Hs_Unlock_Pin_n_

Example:

<Hs_Unlock_Pin_1_>0000</Hs_Unlock_Pin_1_>

Default Value

0000

Allowed Values

Integer

Units

Integer

Limits

4 digits

Description

Indicates the PIN to unlock the handset..

Handset Menu

None

Hs_Vibrate_n_

Syntax Description

XML Tag Name

Hs_Vibrate_n_

Example:

<Hs_Vibrate_1_>0</Hs_Vibrate_1_>

Default Value

0

Allowed Values

- 0: Off

- 1: Vibrate then ring

- 2: Vibrate only

- 3: Vibrate and ring

Units

Options without units

Limits

Option

Description

Sets the handset to vibrate mode when you have an incoming call.

This setting isn't available in 6823 Handset.

Handset Menu

Settings > Audio settings > Vibrate