Consult Message

1

Switch Off Message LED

1

Number

<the code that turns MWIs on>

Prefix Meaning

Local Features

Local Features

Consult Message

Number

<the code that turns MWIs off>

Prefix Meaning

Local Features

Local Features

Switch Off Message LED

Directory Number

<the extension number of the voice messaging port>

Set Type

4620 (VPS + CLIP)

Directory Number

<the pilot number of the hunting group for the voice messaging ports>

Type of Hunting Group

RSVP Hunting Group

Search Type

Sequential

Release transfer
(blind transfer)

Program the phone to forward calls to the pilot number when:

• The extension is busy

• The call is not answered

Supervised transfer

Program the user station to forward calls to the pilot number only when the call is not answered (on the phone system, the number of rings before forwarding must be more than the number of rings to supervise the call). Confirm that call forwarding is disabled when the extension is busy.

Username

Enter admin.

Password

Enter IpodAdmin.

Username

Enter admin.

Password

Enter IpodAdmin.

Old Password

Enter IpodAdmin.

(This setting is case sensitive.)

New Password

Enter your new password.

(This setting is case sensitive.)

Confirm Password

Enter your new password.

(This setting is case sensitive.)

E-mail Alarms Enabled

Select No.

SNMP Traps Enabled

Select No.

Name

Accept the default or enter another descriptive name of the VoIP host group.

Load-Balanced

(Unity Connection without a cluster) Select False.

(Unity Connection with a cluster configured) Select False.

Fault-Tolerant

(Unity Connection without a cluster) Select False.

(Unity Connection with a cluster configured) Select True.

Name

Enter Inbound_PBX_Calls or another unique name.

This TDM trunk group handles all incoming calls from the phone system.

Selection Direction

Select Ascending.

Selection Mode

Select Linear.

Port/Channel Content

Enter the numbers of the PIMG ports that handle inbound calls. For example, enter “*” for all PIMG ports, or enter “1-6” for the first six PIMG ports.

Name

Enter MWIs or another unique name.

This TDM trunk group handles outbound MWI calls (where applicable).

Selection Direction

Select Ascending.

Selection Mode

Select Cyclic.

Port/Channel Content

Enter the numbers of the PIMG ports that dial out MWIs. For example, enter “*” for all PIMG ports, or enter “7,8” for the last two PIMG ports.

Name

Enter Outbound_PBX_Calls or another unique name.

This TDM trunk group handles all outbound calls from Unity Connection.

Selection Direction

Select Descending.

Selection Mode

Select Linear.

Port/Channel Content

Enter * for all channels in all ports.

Enter the numbers of the PIMG ports that handle outbound (dialout) calls. For example, enter “*” for all PIMG ports, or enter “7,8” for the last two PIMG ports.

Enable

Check this check box.

Rule Label

Enter MWI_Calls or another name.

This inbound VoIP rule handles all MWI calls from Unity Connection.

Request Type

Select Message.

Originating VoIP Host Address

Enter *.

Calling Number

Enter *.

Calling Name

Enter *.

Called Number

Enter *.

Called Name

Enter *.

Redirect Number

Enter *.

Redirect Name

Enter *.

Device Selection

Outbound Destination

Select TDM.

Trunk Group

Select the name of the TDM trunk group that you created for MWIs in Step 41. For example, select “MWIs.”

CPID Manipulation

Calling Number

Enter S.

Calling Name

Enter S.

Called Number

Enter D.

Called Name

Enter D.

Redirect Number

Enter R.

Redirect Name

Enter R.

Select Primary/Alternate Route

Primary

Select Primary.

Enable

Check this check box.

Rule Label

Enter Outbound_UC_Calls or another name.

This inbound VoIP rule handles all outbound calls from Unity Connection.

Request Type

Select Call.

Originating VoIP Host Address

Enter *.

Calling Number

Enter *.

Calling Name

Enter *.

Called Number

Enter *.

Called Name

Enter *.

Redirect Number

Enter *.

Redirect Name

Enter *.

Device Selection

Outbound Destination

Select TDM.

Trunk Group

Select the name of the TDM trunk group that you created for outbound calls in Step 43. For example, select “Outbound_PBX_Calls.”

CPID Manipulation

Calling Number

Enter S.

Calling Name

Enter S.

Called Number

Enter D.

Called Name

Enter D.

Redirect Number

Enter R.

Redirect Name

Enter R.

Select Primary/Alternate Route

Primary

Select Primary.

Enable

Check this check box.

Rule Label

Enter Inbound_Rule_1 or another name.

This inbound TDM rule handles all incoming calls from the phone system.

Request Type

Select Call.

Trunk Group

Select the name of the TDM trunk group that you created for incoming calls from the phone system in Step 39. For example, select “Inbound_PBX_Calls.”

Calling Number

Enter the applicable matching rule used. For example, enter “*” for all.

Calling Name

Enter the applicable matching rule used. For example, enter “*” for all.

Called Number

Enter the applicable matching rule used. For example, enter “*” for all.

Called Name

Enter the applicable matching rule used. For example, enter “*” for all.

Redirect Number

Enter the applicable matching rule used. For example, enter “*” for all.

Redirect Name

Enter the applicable matching rule used. For example, enter “*” for all.

Device Selection

Outbound Destination

Select VoIP.

Host Group

Select the name of the VoIP host group that you created for Unity Connection in Step 31.

CPID Manipulation

Calling Number

Enter the applicable matching rule used. For example, enter “*” for all.

Calling Name

Enter the applicable matching rule used. For example, enter “*” for all.

Called Number

Enter the applicable matching rule used. For example, enter “*” for all.

Called Name

Enter the applicable matching rule used. For example, enter “*” for all.

Redirect Number

Enter the applicable matching rule used. For example, enter “*” for all.

Redirect Name

Enter the applicable matching rule used. For example, enter “*” for all.

Select Primary/Alternate Route

Primary

Select Primary.

PCM Coding

Select uLaw.

Minimum Call Party Delay (ms)

Enter 500.

Maximum Call Party Delay (msecs)

Enter 2000.

Dial Digit on Time (ms)

Enter 100.

Dial Inter-Digit Time (ms)

Enter 100.

Dial Pause Time (ms)

Enter 2000.

Turn MWI On FAC

Enter the code that turns MWIs on.

Turn MWI Off FAC

Enter the code that turns MWIs off.

Outbound Call Connect Timeout (ms)

Enter 10000.

Wait for Ringback/Connect on Blind Transfer

Select Yes.

Hunt Group Extension

Enter the pilot number of the Unity Connection voice messaging ports.

User-Agent

Host and Domain Name

Enter the host and domain name of the PIMG unit.

Transport Type

Select UDP.

Call as Domain Name

Select No.

Invite Expiration (sec)

Enter 120.

Server

DNS Server Address

Enter the IP Address of the Domain Name Server that the PIMG unit use.

Registration Server Address

Leave this field blank.

Registration Server Port

Enter 5060.

Registration Expiration (sec)

Enter 3600.

TCP/UDP

UDP/TCP Transports Enabled

Select Yes.

TCP/UDP Server Port

Enter 5060.

Proxy

Primary Proxy Server Address

Leave this field blank.

Primary Proxy Server Port

Not applicable. Leave the default setting.

Backup Proxy Server Address

Not applicable. Leave the default setting.

Backup Proxy Server Port

Not applicable. Leave the default setting.

Proxy Query Interval

Enter 10.

Timing

T1 Time (ms)

Enter 400.

T2 Time (ms)

Enter 3000.

Monitoring

Monitor Call Connections

Select No.

Audio

Audio Compression

Select the preferred codec for audio compression.

RTP Digit Relay Mode

Select RFC2833.

Signaling Digit Relay Mode

Select Off.

Voice Activity Detection

Select Off.

Frame Size

Select the applicable setting:

• G.711—20

• G.729AB—10

  Failure to use the correct setting results in recorded messages containing nothing but silence.

Frames Per Packet

Select the applicable setting:

• G.711—1

• G.729AB—2

  Failure to use the correct setting results in recorded messages containing nothing but silence.

Call Control QOS Byte

Enter 104.

RTP QOS Byte

Enter 184.

Client IP Address

Enter the new IP address you want to use for the PIMG unit.

(This is the IP address that you enter in Cisco Unity Connection Administration when you create the integration.)

Client Subnet Mask

Enter the new subnet mask, if the subnet mask is different from the default IP address.

Default Network Gateway Address

Enter the IP address of the default network gateway router that the PIMG units uses.

BOOTP Enabled

Select No.

Phone System

Select the name of the phone system that you entered in Step 3.

Create From

Select Port Group Template and select SIP to DMG/PIMG/TIMG in the drop-down box.

Display Name

Enter a descriptive name for the port group. You can accept the default name or enter the name that you want.

SIP Security Profile

Select 5060.

SIP Transport Protocol

Select the SIP transport protocol that Unity Connection uses.

IP Address or Host Name

Enter the IP address of the PIMG unit that you are integrating with Unity Connection.

Port

Enter the SIP port of the PIMG unit that Unity Connection connects to. We recommend that you use the default setting.

This name must match the setting in the TCP/UDP Server Port field on the Configuration > VoIP > General page of the PIMG unit. Otherwise, the integration cannot function correctly.

Enabled

Check this check box.

Number of Ports

Enter 8.

(If you want to use fewer than eight voice messaging ports, enter the number of voice messaging ports that you want to use on this PIMG unit.)

Phone System

Select the name of the phone system that you entered in Step 3.

Port Group

Select the name of the port group that you added in Step 8.

Enabled

Check this check box to enable the port. The port is enabled during normal operation.

Uncheck this check box to disable the port. When the port is disabled, calls to the port get a ringing tone but are not answered. Typically, the port is disabled only by the installer during testing.

Extension

Enter the extension for the port as assigned on the phone system.

Answer Calls

Check this check box to designate the port for answering calls. These calls can be incoming calls from unidentified callers or from users.

Perform Message Notification

Check this check box to designate the port for notifying users of messages. Assign Perform Message Notification to the least busy ports.

Send MWI Requests

(Serial integrations only) Uncheck this check box. Otherwise, the integration may not function correctly.

(Digital and analog integrations only) Check this check box to designate the port for turning MWIs on and off. Assign Send MWI Requests to the least busy ports

Allow TRAP Connections

Check this check box so that users can use the port for recording and playback through the phone in Unity Connection web applications. Assign Allow TRAP Connections to the least busy ports.

Outgoing Hunt Order

Enter the priority order in which Unity Connection uses the ports when dialing out (for example, if the Perform Message Notification, Send MWI Requests, or Allow TRAP Connections check box is checked). The highest numbers are used first. However, when multiple ports have the same Outgoing Hunt Order number, Unity Connection uses the port that has been idle the longest.

From Phone System

Enter the display name of the phone system that you are creating a trunk for.

To Phone System

Enter the display name of the previously existing phone system that the trunk connects to.

Trunk Access Code

Enter the extra digits that Unity Connection must dial to transfer calls through the gateway to extensions on the previously existing phone system.