|
|
|
aaa |
Authentication, authorization, and accounting. |
Accounting for billing or security purposes when you use RADIUS or TACACS+. |
access-list |
Add an access list entry. |
— |
alias |
Create command alias. |
— |
arp |
Set a static ARP entry. |
Maps Mac address to IP address. |
async-bootp |
Modify system bootp parameters. |
Supports extended BOOTP requests. Specifies information sent in response to BOOTP requests. |
banner |
Define a login banner. |
Displays a banner on terminals with an interactive EXEC. |
boot |
Modify system boot parameters. |
— |
buffers |
Adjust system buffer pool parameters. |
Adjusts buffer pool settings and the limits at which temporary buffers are created and destroyed. |
busy-message |
Display message when connection to host fails. |
— |
cdp |
Global Cisco Discovery Protocol configuration subcommands. |
— |
chat-script |
Define a modem chat script. |
— |
class-map |
QoS class-map command. |
Enters config-cmap configuration mode. |
clns |
Global CLNS configuration subcommands. |
— |
clock |
Configure time-of-day clock. |
— |
config-register |
Define the configuration register. |
Defines system startup behavior. |
controller |
Configure a specific controller. |
Configures a controller-type and enters config-controller mode. |
default |
Set a command to its default value. |
— |
default-value |
Default character-bits values. |
Changes the flow control default value from a 7-bit width to an 8-bit width. |
define |
Interface range macro definition. |
— |
dialer |
Dialer commands. |
— |
dialer-list |
Create a dialer list entry. |
— |
dnsix-dmdp |
Provide DMDP service for DNSIX. |
— |
dnsix-nat |
Provide DNSIX service for audit trails. |
— |
do |
To run exec commands in config mode. |
— |
download- compatible-config |
Generate a configuration compatible with older software. |
— |
enable |
Modify enable password parameters. |
— |
end |
Exit from configure mode. |
— |
exception |
Perform exception handling. |
— |
exit |
Exit from configure mode. |
Closes terminal sessions and exits configuration modes. |
file |
Adjust file system parameters. |
— |
help |
Description of the interactive help system. |
— |
hostname |
Set system network name. |
Specifies the host name of the RPM-XF. |
interface |
Select an interface to configure and enter config-if mode. |
Configures an interface type and enters config-if mode. |
ip |
Global IP configuration subcommands. |
— |
ipc |
Configure IPC system. |
— |
isis |
Global ISIS configuration subcommands. |
— |
kerberos |
Configure Kerberos. |
— |
key |
Key management. |
— |
line |
Configure a terminal line. |
— |
logging |
Modify message logging facilities. |
Stores or deletes the log. |
login-string |
Define a host-specific login string. |
— |
map-class |
Configure static map class. |
Defines parameters shared with the dialer map command. |
map-list |
Configure static map list. |
Specifies a map group and links it to a local E.164 or X.121 source address and a remote E.164 or X.121 destination address. |
menu |
Define a user-interface menu. |
Specifies underlying commands for user interface menus. |
microcode |
Configure microcode. |
— |
modemcap |
Modem Capabilities database. |
— |
mpls |
Configure MPLS parameters. |
— |
multilink |
PPP multilink global configuration. |
— |
no |
Negate a command or set its defaults. |
— |
ntp |
Configure NTP. |
Configures Network Time Protocol. |
parser |
Configure parser. |
— |
policy-map |
Configure QoS policy map. |
Enters config-pmap mode. From there you can enter config-pmap-c mode. |
priority-list |
Build a priority list. |
Establishes queuing priorities based upon the protocol type. This is one of the steps to establishing queuing priorities based on logical unit (LU) addresses. |
privilege |
Command privilege parameters. |
Adjusts privilege level needed to access configuration commands. |
process-max-time |
Maximum time for process to run before voluntarily relinquishing processor. |
— |
prompt |
Set system prompt. |
Customizes the system prompt. |
queue-list |
Build a custom queue list. |
Assigns priority queueing on an interface. |
rbe |
Commands for Routing RFC 1483 Ethernet encapsulated packets. |
— |
regexp |
regexp commands. |
— |
resume-string |
Define a host-specific resume string. |
— |
rlogin |
Rlogin configuration commands. |
— |
rmon |
Remote monitoring. |
Remote monitoring for Ethernet interfaces. |
route-map |
Create route-map or enter route-map command mode. |
Defines the conditions for redistributing routes from one routing protocol into another or enables policy routing. Enters config-route-map mode. |
router |
Enable a routing process. |
Enables various routing protocols. |
rtr |
RTR base configuration. |
Configures a response time reporter probe. |
scheduler |
Scheduler parameters. |
Schedules timing for CPU process handling. |
service |
Modify use of network-based services. |
— |
snmp |
Modify non-engine SNMP parameters. |
— |
snmp-server |
Modify SNMP parameters. |
— |
standby |
Global HSRP configuration commands. |
— |
state-machine |
Define a TCP dispatch state machine. |
— |
tacacs-server |
Modify TACACS query parameters. |
— |
tag-switching |
Dynamic tag switching command |
— |
template |
Select template to configure. |
— |
terminal-queue |
Terminal queue commands. |
Changes the retry interval for a terminal port queue. |
tftp-server |
Provide TFTP service for netload requests. |
— |
time-range |
Define time range entries. |
— |
username |
Establish user name authentication. |
Assigns a user name that is displayed in the configuration files. |
vc-class |
Configure per VC parameters. |
— |
virtual-profile |
Virtual profile configuration. |
Enables virtual profiles by AAA configuration. |
virtual-template |
Virtual template configuration. |
— |
vpdn |
Virtual Private Dialup Network |
— |
vpdn-group |
VPDN group configuration. |
— |
vpdn-template |
VPDN template configuration. |
— |