MGX 8850 and MGX 8950 Command Reference, Release 2.1
Chapter: ILMI Commands
- Position-Dependent and Keyword-Driven Parameters
- Command Entry
- Identifying Physical and Logical Elements
- addlmi
- addprfx
- clrilmicnt
- clrlmistat
- cnfaddrreg
- cnfautocnf
- cnfilmi
- cnfilmienable
- cnfilmiproto
- dbgilmi
- dellmi
- delprfx
- dnilmi
- dnlmi
- dspilmi
- dspilmiaddr
- dspilmicnt
- dspilmis
- dsplmi
- dsplmis
- dsplmistat
- dsppnilmi
- dspprfx
- upilmi
- uplmi
ILMI and LMI Commands
This chapter describes the ILMI and LMI commands. These commands let you add, delete, configure, display status, and create statistics for ILMI or LMI at the UNI or for PNNI. For the UNI, commands are executed on the CLI of an AXSM or AXSM-E. For PNNI, commands are executed on the CLI of a PXM45. The chapter begins with a description of issues related to command entry, port identification, and so on.
Position-Dependent and Keyword-Driven Parameters
A command can include parameters that are keyword-driven or position-dependent.
For position-dependent parameters, you must type parameters in the order they appear in the syntax description or on-line help. To create a logical port, for example, the position-dependent syntax is:
addport <ifNum> <bay.line> <guaranteedRate> <maxrate> <sctID> <ifType> [vpi]
For a keyword-driven parameter, a keyword must precede the value. The keyword is preceded by a dash and followed by the parameter (-timeout <secs>, for example). The order you enter keyword-driven parameters does not matter—although any preceding or succeeding, position-dependent parameters must appear as they do in the command syntax description.
In the following syntax example, the command is to delete more than one connection at a time. The mandatory, position-dependent connection identifier consist of a logical port (ifNum) and the VPI and VCI of the first connection to delete. After the connection identifier, the line shows two optional, keyword-driven parameters. These keyword-driven parameters let you enter the number of connections to delete and specify verbose mode:
delcons <ifNum> <vpi> <vci> [-num <num. conns to del>] [-verbose < 1 | 0 >]
Command Entry
When you enter a command with the current version of the product, you must type all intended arguments before you press the Return key or Enter key.
If you press the Return key or Enter key with incorrect parameters or no parameters (if the command requires parameters), a message displays the syntax and parameter ranges. The returned message may also suggest what the problem is. For example, the message may warn of too few parameters. No error messages or warnings appear until you complete the command.
Identifying Physical and Logical Elements
The Private Network-to-Network Interface (PNNI) control protocol and the AXSM use different formats to identify the same elements. This section describes the format of these elements in the PNNI and AXSM contexts and how they correspond to each other. When you configure an item on the switch, you may need to specify it in PNNI as well as the AXSM. For example, if you configure a PNNI port on the CLI of the PXM45, you also need to configure a logical port on the CLI of the AXSM. Furthermore, when you display a connection on the AXSM, you identify that same connection using a different format on the PXM45. For specific examples of these parallel actions, see the Cisco MGX 8850 and MGX 8950 Switch Software Configuration Guide, Release 2.1.
Note 
Apart from the way PNNI and the lower levels of logic identify the same element, the issue of configuration sequence needs explanation. For example, when you configure logical ports, you must complete certain tasks on the AXSM CLI before and after related PNNI tasks. This manual describes prerequisites for certain commands, but refer to the Cisco MGX 8850 and MGX 8950 Switch Software Configuration Guide, Release 2.1 for more details on these sequences.
AXSM Format
The AXSM items that you identify for addressing purposes are:
•Slot
•Bay
•Line
•Logical port
A logical port on an AXSM or AXSM-E (and its CLI) always uses the label ifNum. For a UNI and NNI interface, a one-to-one correspondence exists between a logical port and a physical line. For virtual trunks, you can configure multiple ports for a line.
The maximum number of logical ports on an AXSM is 60 or 32 on an AXSM-E, regardless of the number of AXSM back cards or whether the interface type is UNI, NNI, or VNNI.
PNNI Format
The PNNI controller requires the following format to identify a physical port:
[shelf.]slot:subslot.port:subport
The PNNI physical port identifier (physical port ID) consists of a series of mandatory elements. Note the period or colon between the elements. The elements of the physical port ID are as follows:
•The shelf is always 1 for the current product and so is usually omitted.
•The slot number of the front card.
•Subslot is the number of the bay where the back card resides. This number is 1 or 2.
•Port is the physical line.
•Subport corresponds to the resource partition on the AXSM. For a UNI or NNI, this resource partition is the same number as the logical port number (ifNum) on the AXSM. For a virtual network-to-network interface (VNNI), these numbers do not directly correspond to each other.
For each physical port number, PNNI also generates a logical port number as an encrypted form of the physical port number. The logical port number appears as an unformatted numerical string. For example, a PNNI physical port ID may have the form 1:1.2:2, so the PNNI logical port number would be 16848898. Where needed, the descriptions in the PNNI command chapter define the need for this logical port number. (This section does not define a PNNI logical port number, nor does it describe the correspondence between an AXSM port and a PNNI logical port number.) For the correspondence between a PNNI physical port and the port identifier on an AXSM, see Table 4-1.
|
|
|
|---|---|
Shelf |
N/A |
Slot |
Slot |
Subslot |
Bay (for upper or lower back card) |
Port |
Line |
Subport |
Logical interface (or port) |
As the table shows, a port from the PNNI side is a line on the AXSM, and a subport from the PNNI side is a logical interface (or logical port) on an AXSM. An example of a PNNI physical port identifier is 1:2.1:1. This portid corresponds to an AXSM, with the following particulars:
Slot 1
Bay 2
Line 1
Logical interface 1 (or logical port 1)
addlmi
Add Local Management Interface—add LMI to support feeder or interoperability.
The addlmi command lets you add extended LMI (XLMI) so that an AXSM logical interface can support one of the following:
•A feeder line to a Release 1 MGX 8850 switch
•Interoperability with a Service Expansion Shelf (SES)
Note By using the addlmi command to add LMI for a feeder shelf, the addfdr command is unnecessary.
Usage Guidelines
Note the following properties and behaviors before you use the addlmi command:
•The only connections that can exist between an MGX 8850 node and a feeder shelf or a Service Expansion Shelf are SPVCs and SPVPs.
•For the feeder application of the addlmi command, the effect is the same as using addfdr, so you do not need to use addfdr for a logical port in addition to addlmi.
•No other ILMI or LMI configuration can exist on the AXSM logical interface.
•No connections can exist on the AXSM logical interface.
•A combined maximum of 16 feeder lines or SES interoperability ports can exist on the switch.
•When a port is configured for an XMLI link with an SES, IP connectivity must be disabled.
•The XLMI timers are not configurable on the AXSM. Timer configuration is done on the SES. The values for the LMI timers on AXSM are:
–SPVC Status Enquiry Timer: 10 seconds
–SPVC Update Status Timer: 10 seconds
–Retry Timers: 5 seconds
Cards on Which This Command Runs
AXSM
Syntax
addlmi <ifNum> <type>
Syntax Description
Related Command
dellmi, uplmi, dnlmi, uplmi, clrlmistat, dsplmi, dsplmis, dsplmistat
Attributes
Log: log |
State: active |
Privilege: ANYUSER |
Example
Add a LMI for a feeder to AXSM port 2. Check the resulting LMI.
M8850_NY.1.AXSM.a > addlmi 2 1
M8850_NY.1.AXSM.a > dsplmi 2
LMI Interface Number : 2
LMI Remote Name : M8850_NY
LMI IP Address : 10.10.10.56
LMI Remote Shelf : 1
LMI Remote Slot : 1
LMI Remote Port : 1
LMI Type : AXSM
LMI Model Number : 8850
LMI Configuration : Up
LMI Link Status : Up
LMI Alarms : Clear
addprfx
Add Prefix—create an address prefix for a UNI or IISP.
The addprfx command lets you add an ATM prefix for ILMI to a UNI or IISP.
Cards on Which This Command Runs
Syntax
addprfx <portid> <atm-prefix>
Syntax Description
portid |
Identifies a PNNI physical port. The format is slot:subslot.port:subport. For a description of each field, see the section, "PNNI Format," at the beginning of the chapter. |
atm-prefix |
A 13-byte ATM prefix (26 hexadecimal characters). |
Related Commands
dspprfx, delprfx
Attributes
Log: log |
State: active |
Privilege: GROUP1 |
Examples
Add prefix47.0091.8100.0000.0000.0ca7.9e01 to PNNI physical port 3:1.1:1. Display ARM address prefixes for this port. Only the one just added exists.
M8850_NY.7.PXM.a > addprfx 3:1.1:1 47.0091.8100.0000.0000.0ca7.9e01
M8850_NY.7.PXM.a > dspprfx 3:1.1:1
ILMI Configured Port Prefix(es):
47.0091.8100.0000.0000.0ca7.9e01
M8850_NY.7.PXM.a >
clrilmicnt
Clear ILMI Counters
Clears the ILMI statistics for a partition and logical interface (or port) on a service module.
Cards on Which This Command Runs
AXSM, AXSM-E
Syntax
clrilmicnt <ifNum> <partId>
Syntax Description
ifNum |
The ranges for logical interface (or AXSM port) number are as follows: • • |
partId |
The ranges for partition identifier are as follows: • • |
Related Commands
dspilmicnt, dspilmi, dspilmis
Attributes
Log: log |
State: active |
Privilege: SUPER_GP |
Examples
Clear the ILMI statistics for logical interface 1, resource partition 1. Before doing so, confirm the existence of these entities by executing dspparts.
pop20two.1.AXSM.a > dspparts
if part Ctlr egr egr ingr ingr min max min max min max
Num ID ID GuarBw MaxBw GuarBw MaxBw vpi vpi vci vci conn conn
(.0001%)(.0001%)(.0001%)(.0001%)
-----------------------------------------------------------------------------
1 1 2 10000 10000 10000 10000 10 100 100 1000 0 10
pop20two.1.AXSM.a > clrilmicnt 1 1
ilmi stats for ifNum 1, partId 1 cleared
clrlmistat
Clear LMI Statistics—clears LMI statistics on an AXSM interface.
The dsplmistat command lets you display general statistics about an LMIs (XLMIs) on an AXSM interface. See also description of the addlmi command.
Cards on Which This Command Runs
AXSM
Syntax
dsplmistat <ifNum>
Syntax Description
ifNum |
The logical interface number has a range of 1-60. |
Related Command
dellmi, uplmi, dnlmi, uplmi, dsplmistat, addlmi, dsplmi, dsplmis
Attributes
Log: log |
State: active, standby |
Privilege: ANYUSER |
Example
After checking the statistics on logical interface 2, clear the LMI statistics then recheck them.
M8850_NY.1.AXSM.a > dsplmistat 2
STATUS REPORT ENQUIRY transmitted : 1
STATUS REPORT ENQUIRY received : 1
STATUS REPORT transmitted : 1
STATUS REPORT received : 1
UPDATE STATUS transmitted : 0
UPDATE STATUS received : 0
UPDATE STATUS ACK transmitted : 0
UPDATE STATUS ACK received : 0
Invalid PDU received : 0
Invalid PDU length received : 0
Invalid PDU IEs received : 0
Invalid Transaction Num received : 0
Unknown PDU type received : 0
NODE STATUS enquiry transmitted : 3605
NODE STATUS enquiry received : 3605
NODE STATUS ack transmitted : 3605
NODE STATUS ack received : 3605
NODE STATUS degrade transmitted : 0
NODE STATUS degrade received : 0
NODE STATUS delete transmitted : 0
NODE STATUS delete received : 0
NODE STATUS unknown received : 0
M8850_NY.1.AXSM.a > clrlmistat 2
M8850_NY.1.AXSM.a > dsplmistat 2
STATUS REPORT ENQUIRY transmitted : 0
STATUS REPORT ENQUIRY received : 0
STATUS REPORT transmitted : 0
STATUS REPORT received : 0
UPDATE STATUS transmitted : 0
UPDATE STATUS received : 0
UPDATE STATUS ACK transmitted : 0
UPDATE STATUS ACK received : 0
Invalid PDU received : 0
Invalid PDU length received : 0
Invalid PDU IEs received : 0
Invalid Transaction Num received : 0
Unknown PDU type received : 0
NODE STATUS enquiry transmitted : 3
NODE STATUS enquiry received : 3
NODE STATUS ack transmitted : 3
NODE STATUS ack received : 3
NODE STATUS degrade transmitted : 0
NODE STATUS degrade received : 0
NODE STATUS delete transmitted : 0
NODE STATUS delete received : 0
NODE STATUS unknown received : 0
M8850_NY.1.AXSM.a >
cnfaddrreg
Configure Address Registration
This command lets you enable or disable ILMI address registration for a port. Before you can run cnfaddrreg, the following must have occurred:
1. The applicable port must have been created by executing addpnport.
2. The port must be downed by executing dnpnport.
The cnfaddrreg command can also enable (or disable) the address registration for backward compatibility.
The peer must support address registration table and procedure, so you must confirm that address registration is enabled on all three places.
Cards on Which This Command Runs
PXM45
Syntax
cnfaddrreg <portid> [{yes | no}]
Syntax Description
In addition to typing a port ID, you must also type either "yes" pr "no."
portid |
Identifies a PNNI physical port. The format is slot:subslot.port:subport. For a description of each field, see the section, "PNNI Format," at the beginning of the chapter. |
yes |
Enable ILMI address registration on the port. The default is "yes" (enabled). |
no |
Disable ILMI address registration on the port. |
Related Commands
None
Attributes
Log: log |
State: active |
Privilege: GROUP1 |
Examples
Disable ILMI address registration on port 4:1.1:11.
Geneva.7.PXM45.a > cnfaddrreg 4:1.1:1 no
cnfautocnf
Configure Auto Configuration
The cnfautocnf command enables or disables ILMI auto configuration for a port. To use this command, the port must be added but administratively down (via dnpnnport).
With auto-configuration enabled, the ILMI slave side starts ILMI auto configuration to negotiate the ATM layer parameters with its peer while ports come up. With auto-configuration disabled, the ILMI slave does not start ATM layer parameter-negotiation while ports come up. Instead, the ILMI slave uses the local configuration parameters. The default state for auto-configuration is enabled.
Cards on Which This Command Runs
PXM45
Syntax
cnfautocnf <portid> [yes | no]
Syntax Description
portid |
Identifies a PNNI physical port. The format is slot:subslot.port:subport. For a description of each field, see the section, "PNNI Format," at the beginning of the chapter. |
yes |
Enable ILMI automatic configuration on the port. Default: yes |
no |
Disable ILMI automatic configuration on the port. |
Attributes
Log: log |
State: active |
Privilege: GROUP1 |
Examples
Enable ILMI auto-configuration on port 4:1.1:11.
Geneva.1.AXSM.a > cnfaddrreg 4:1.1:1 no
cnfilmi
Configure ILMI
Configures the card-level interim local management interface (ILMI) for the AXSM. Activating the card-level ILMI through cnfilmi requires a pre-existing logical port (see addport) and resource partition (see addrscprtn or addpart). No response appears unless an error occurs.
Note For network-level ILMI in relation to PNNI, run the PNNI-specific ILMI commands on the PXM45.
Cards on Which This Command Runs
AXSM, AXSM-E
Syntax
cnfilmi <ifNum> -id <partitionID> -ilmi <ilmiEnable> -vpi <vpi> -vci <vci> -trap <ilmiTrapEnable> -s <keepAliveInt> -t <pollingIntervalT491> -k <pollInctFact>
Syntax Description
Related Commands
dspilmi, dspilmis, dspilmicnt, clrilmicnt, dnilmi, upilmi
Attributes
Log: log |
State: active |
Privilege: GROUP1 |
Examples
Unknown.1.AXSM.a > cnfilmi 1 1 -ilmi 1 -vpi 40 -vci 99 -s 10 -t 10 -k 10
cnfilmienable
Enables ILMI on a PNNI port. Prior to cnfilmienable, the port must be administratively down. Use the dnpnport command to down the port and uppnport to up it.
Cards on Which This Command Runs
PXM45
Syntax
cnfilmienable <portid> [yes | no]
Syntax Description
portid |
Identifies a PNNI physical port. The format is slot:subslot.port:subport. For a description of each field, see the section, "PNNI Format," at the beginning of the chapter. |
yes or |
Type "yes" to enable ILMI or "no" to disable ILMI on the specified PNNI port. Default: disabled |
Related Commands
dnpnport, uppnport, dsppnilmi
Attributes
Log: log |
State: active |
Privilege: GROUP1 |
Examples
Enable ILMI on a PNNI port 4:1.1:11. First, disable the port by using dnpnport.
Geneva.1.PXM.a > dspilmi 4:1.1:11
INFO: No ilmi address registered
Geneva.1.AXSM.a > cc 7
(session redirected)
Geneva.7.PXM.a > dnpnport 4:1.1:11
Geneva.7.PXM.a > cnfilmienable 4:1.1:1
Geneva.7.PXM.a > uppnport 4:1.1:11
Geneva.7.PXM.a >
cnfilmiproto
Configure ILMI Protocol
The cnfilmiproto command lets you configure how PNNI reacts to ILMI events that occur on the VSI slave (a service module). Use the dsppnilmi command to confirm changes to the configuration.
Cards on Which This Command Runs
PXM45
Syntax
cnfilmiproto <portid> [-securelink {yes | no}] [-attachmentpoint {yes | no]
[-modlocalattrstd {yes | no]
Syntax Description
portid |
Identifies a PNNI physical port. The format is slot:subslot.port:subport. For a description of each field, see the section, "PNNI Format," at the beginning of the chapter. |
-securelink |
Sets the flag securelink to make PNNI release the call if it loses connection to the ILMI slave. no: do not enable the ILMI Secure link protocol. Default: yes |
-attachmentpoint |
Sets the flag attachmentpoint to make PNNI release the call if the slave ILMI session sees changes in peer information, such as the system name or system ID. no: do not enable the detection of loss of attachmentpoint protocol. Default: yes |
-modlocalattrstd |
Sets the flag modlocalattrstd to make PNNI release the call if the slave ILMI sees ATM layer (partition resource) changes, such as the VPI or VCI. no: disable the ILMI standard procedure for modification of local ATM param. Default: yes |
Related Commands
dsppnilmi
Attributes
Log: log |
State: active |
Privilege: GROUP1 |
Example
SanJose.7.PXM.a > cnfilmiproto 11:2.1.1 -securelink no -attachmentpoint no -modlocalattrstd yes
dbgilmi
Debug ILMI
Use dbgilmi to debug ILMI functionality (such as address registration or auto configuration).
Note VSI pass-through information is exchanged between only the controller (PPNI) and the switch.
Cards on Which This Command Runs
PXM45
Syntax
dbgilmi {enable | disable} [<portid>] [-log <vsi | func | minor | major | warning | error | dump | fatal | all>]
[-dbg <vsi | func | minor | major | warning | error | dump | fatal | all>]
Syntax Description
enable | disable |
Activate or de-activate ILMI debugging. |
portid |
Identifies a PNNI physical port. The format is slot:subslot.port:subport. For a description of each field, see the section, "PNNI Format," at the beginning of the chapter. |
-log |
If you type the optional keyword log, follow it with at least one of the following: vsi |
-dbg |
If you type the optional keyword dbg, follow it with at least one of the following: vsi |
Attributes
Log: log |
State: active, standby |
Privilege: SERVICE_GP |
dellmi
Delete Local Management Interface—delete LMI to delete a feeder connection or SES interoperability.
The dellmi command lets you delete LMI from an AXSM logical interface. By doing so, the feeder line or connection to the SES is removed.
Note Remove all connections before you delete LMI on an interface.
Cards on Which This Command Runs
AXSM
Syntax
dellmi <ifNum>
Syntax Description
ifNum |
The logical interface number has a range of 1-60. |
Related Command
addlmi, uplmi, dnlmi, uplmi, clrlmistat, dsplmi, dsplmis, dsplmistat
Attributes
Log: log |
State: active |
Privilege: ANYUSER |
Example
Delete the LMI on port 2, then check to see if any LMIs remain.
M8850_NY.1.AXSM.a > dellmi 2
M8850_NY.1.AXSM.a > dsplmis
IF Remote Remote Rmt Rmt LMI LMI LMI
No. Name IP Slot Port Admin Oper Alarms
--- ------- ------------ ----- ----- ----- ---- ------
M8850_NY.1.AXSM.a >
delprfx
Delete Prefix
The delprfx command lets you delete an ILMI address prefix associated with a UNI, IISP, or AINI.
Cards on Which This Command Runs
PXM45
Syntax
delprfx <portid> <atm-prefix>
Syntax Description
portid |
Identifies a PNNI physical port. The format is slot:subslot.port:subport. For a description of each field, see the section, "PNNI Format," at the beginning of the chapter. |
atm-prefix |
A 13-byte ATM address prefix, specified as 26 hexadecimal characters. |
Related Commands
addprfx, dspprfx
Attributes
Log: log |
State: active |
Privilege: GROUP1 |
Examples
Delete ATM prefix 47.0091.8100.0000.0000.0ca7.9e01 from PNNI physical port 3:1.1:1. Display prefixes for this port.
M8850_NY.7.PXM.a > delprfx 3:1.1:1 47.0091.8100.0000.0000.0ca7.9e01
M8850_NY.7.PXM.a > dspprfx 3:1.1:1
INFO: No Prefix registered
M8850_NY.7.PXM.a >
dnilmi
Down ILMI
The dnilmi command lets you de-activate (down) ILMI on a logical port so you can modify a configuration, troubleshoot, or run certain commands that require ILMI to be inoperative.
Cards on Which This Command Runs
AXSM, AXSM-E
Syntax
dnilmi <ifNum> <partId>
Syntax Description
ifNum |
The ranges for logical interface (or AXSM port) number are as follows: • • |
partId |
The ranges for partition identifier are as follows: • • |
Related Commands
dspilmi, dspilmis, upilmi
Attributes
Log: log |
State: active, standby |
Privilege: SERVICE_GP |
dnlmi
Down Local Management Interface
De-activates the Local Management Interface (LMI) on the specified logical port (ifNum).
Cards on Which This Command Runs
AXSM
Syntax
dnlmi <ifNum>
Syntax Description
ifNum |
The interface number of the logical port on which to activate the LMI. The range is 1-60. |
Related Commands
uplmi
Attributes
Log: log |
State: active |
Privilege: ANYUSER |
Example
dnlmi 2
dspilmi
Display ILMI
Display the configuration for the interim local management interface (ILMI) on a specific port. The information in the dspilmi output was configured through the cnfilmi command.
Cards on Which This Command Runs
AXSM, AXSM-E
Syntax
dspilmi <ifNum> <partId>
Syntax Description
ifNum |
The ranges for logical interface (or AXSM port) number are as follows: • • |
partId |
The range for partition identifier is as follows: • • |
Related Commands
cnfilmi, dspilmis, dspilmicnt, clrilmicnt
Attributes
Log: nolog |
State: active, standby |
Privilege: ANYUSER |
Examples
Display ILMI information for logical interface 1, resource partition 1.
pinnacle3.1.2.AXSM.a > dspilmi 1 1
Sig. rsrc Ilmi Sig Sig Ilmi S:Keepalive T:conPoll K:conPoll
Port Part State Vpi Vci Trap Interval Interval InactiveFactor
---- ---- ---- ---- ---- --- ------------ ---------- ----------
1 1 Off 0 16 On 1 5 4
pinnacle3.2.AXSM.a >
dspilmiaddr
Display ILMI Address—displays ILMI registered port addresses.
The dspilmiaddr command lets you display the ATM addresses registered by the peer via the ILMI address registration mechanism.
Cards on Which This Command Runs
PXM45
Syntax
dspilmiaddr <portid>
Syntax Description
portid |
Identifies a PNNI physical port. The format is slot:subslot.port:subport. For a description of each field, see the section, "PNNI Format," at the beginning of the chapter. |
Related Commands
cnfilmienable, cnfilmiproto, dsppnilmi, pntraceilmi
Attributes
Log: nolog |
State: active, standby |
Privilege: ANYUSER |
Examples
Display the ILMI address on port 3:2.2:4.
8850_NY.7.PXM.a > dspilmiaddr 3:2.2:4
INFO: No ilmi address registered
dspilmicnt
Display ILMI Counters
Displays the ILMI counters for a particular resource partition on a particular logical port.
Cards on Which This Command Runs
AXSM, AXSM-E
Syntax
dspilmicnt <ifNum> <partId>
Syntax Description
ifNum |
The ranges for logical interface (or AXSM port) number are as follows: • • |
partId |
The range for partition identifier is as follows: • • |
Related Commands
cnfilmi, dspilmi, dspilmis, clrilmicnt, dnilmi, upilmi
Attributes
Log: nolog |
State: active, standby |
Privilege: ANYUSER |
Examples
Display the ILMI counters for logical port 1/partition ID 1 on the current AXSM card.
Unknown.1.AXSM.a > dspilmicnt 1 1
If Number : 1
Partition Id : 1
SNMP Pdu Received : 65
GetRequest Received : 34
GetNext Request Received : 0
SetRequest Received : 0
Cold Start Trap Received : 0
GetResponse Received : 31
GetResponse Transmitted : 34
GetRequest Transmitted : 34
Cold Start Trap Transmitted : 0
VPC Trap Transmitted : 0
VCC Trap Transmitted : 0
Unknown Type Received : 0
ASN1 Pdu Parse Error : 0
No Such Name Error : 0
Pdu Too Big Error : 0
dspilmis
Display ILMI Configurations
The dspilmis command lets you display the configuration of all interim local management interfaces (ILMIs) on the service module.
Cards on Which This Command Runs
AXSM, AXSM-E
Syntax
dspilmis
Related Commands
cnfilmi, dspilmi, dspilmicnt
Attributes
Log: nolog |
State: active, standby |
Privilege: ANYUSER |
Examples
Display all ILMIs on the current service module.
pop20two.1.AXSM.a > dspilmis
Sig. rsrc Ilmi Sig Sig Ilmi S:Keepalive T:conPoll K:conPoll
Port Part State Vpi Vci Trap Interval Interval InactiveFactor
---- ---- ---- ---- ---- --- ------------ ---------- ----------
1 2 On 0 16 On 1 5 4
2 2 Off 0 16 On 1 5 4
3 2 Off 0 16 On 1 5 4
pop20two.1.AXSM.a >
dsplmi
Display Local Management Interface—display details about LMI on a logical interface.
The dsplmi command lets you display details about an extended LMI on an AXSM logical interface. See also description of the addlmi command. Each LMI can support one of the following:
•A feeder line to a Release 1 MGX 8850 switch
•Interoperability with a Service Expansion Shelf (SES)
Cards on Which This Command Runs
AXSM
Syntax
dsplmi <ifNum>
Syntax Description
ifNum |
The logical interface number has a range of 1-60. |
Related Command
dellmi, uplmi, dnlmi, uplmi, clrlmistat, addlmi, dsplmis, dsplmistat
Attributes
Log: log |
State: active |
Privilege: ANYUSER |
Example
Display the LMI on AXSM port 2.
M8850_NY.1.AXSM.a > dsplmi 2
LMI Interface Number : 2
LMI Remote Name : M8850_NY
LMI IP Address : 10.10.10.56
LMI Remote Shelf : 1
LMI Remote Slot : 1
LMI Remote Port : 1
LMI Type : AXSM
LMI Model Number : 8850
LMI Configuration : Up
LMI Link Status : Up
LMI Alarms : Clear
dsplmis
Display Local Management Interfaces—display all LMIs on an AXSM.
The dsplmis command lets you display general information about all extended LMIs (XLMIs) on an AXSM card. See also description of the addlmi command. Each LMI can support one of the following:
•A feeder line to a Release 1 MGX 8850 switch
•Interoperability with a Service Expansion Shelf (SES)
Cards on Which This Command Runs
AXSM
Syntax
dsplmis
Syntax Description
No parameters
Related Command
dellmi, uplmi, dnlmi, uplmi, clrlmistat, addlmi, dsplmi, dsplmistat
Attributes
Log: log |
State: active |
Privilege: ANYUSER |
Example
Display all LMIs on the current AXSM. The display shows that only one LMI exists.
M8850_NY.1.AXSM.a > dsplmis
IF Remote Remote Rmt Rmt LMI LMI LMI
No. Name IP Slot Port Admin Oper Alarms
--- ------- ------------ ----- ----- ----- ---- ------
2 M8850_NY 10.10.10.56 1 1 Up Up Clear
dsplmistat
Display Local Management Interface Statistics—display statistics for an LMIs on an AXSM port.
The dsplmistat command lets you display general statistics about an LMIs (XLMIs) on an AXSM interface. See also description of the addlmi command.
Cards on Which This Command Runs
AXSM
Syntax
dsplmistat <ifNum>
Syntax Description
ifNum |
The logical interface number has a range of 1-60. |
Related Command
dellmi, uplmi, dnlmi, uplmi, clrlmistat, addlmi, dsplmi, dsplmis
Attributes
Log: log |
State: active, standby |
Privilege: ANYUSER |
Example
Display LMI statistics on AXSM port 2.
M8850_NY.1.AXSM.a > dsplmistat 2
STATUS REPORT ENQUIRY transmitted : 1
STATUS REPORT ENQUIRY received : 1
STATUS REPORT transmitted : 1
STATUS REPORT received : 1
UPDATE STATUS transmitted : 0
UPDATE STATUS received : 0
UPDATE STATUS ACK transmitted : 0
UPDATE STATUS ACK received : 0
Invalid PDU received : 0
Invalid PDU length received : 0
Invalid PDU IEs received : 0
Invalid Transaction Num received : 0
Unknown PDU type received : 0
NODE STATUS enquiry transmitted : 2748
NODE STATUS enquiry received : 2748
NODE STATUS ack transmitted : 2748
NODE STATUS ack received : 2748
NODE STATUS degrade transmitted : 0
NODE STATUS degrade received : 0
NODE STATUS delete transmitted : 0
NODE STATUS delete received : 0
NODE STATUS unknown received : 0
M8850_NY.1.AXSM.a >
dsppnilmi
Display PNNI ILMI
Displays the ILMI information for a PNNI logical port. The ILMI state can be one of the following.
Note The VC for ILMI is a control channel, but its bandwidth parameters are fixed, as follows:
PCR=1000 cps; SCR=50cps; and MBS=1024 cells.
The bandwidth used by ILMI (when enabled) and other control-type VCs (see cnfpnctlvc) adds to the bandwidth load on the port. Use dspload to determine the load on port resources.
Cards on Which This Command Runs
PXM45
Syntax
dsppnilmi <portid>
Syntax Description
portid |
Identifies a PNNI physical port. The format is slot:subslot.port:subport. For a description of each field, see the section, "PNNI Format," at the beginning of the chapter. |
Related Commands
dspilmi
Attributes
Log: nolog |
State: active, standby |
Privilege: ANYUSER |
Examples
Display the ILMI for port 6:1.1:1. For comparison, run the dspilmi command on the card in slot 6, Note that it contains information that corresponds to the dsppnilmi output.
M8850_NY.7.PXM.a > dsppnilmi 6:1.1:1
Port: 6:1.1:1 Port Type: ENNI Side: network
Autoconfig: disable UCSM: disable
Secure Link Protocol: enable
Change of Attachment Point Procedures: enable
Modification of Local Attributes Standard Procedure: enable
Addressreg: disable
VPI: 0 VCI: 0
Max Prefix: 0 Total Prefix: 0
Max Address: 0 Total Address: 0
Resync State: 0 Node Prefix: no
Peer Port Id: 0 System_Id : 0.0.0.0.0.0
Peer Addressreg: disable
Peer Ip Address : 0.0.0.0
Peer Interface Name :
ILMI Link State : Disable
ILMI Version : ilmi40
INFO: No Prefix registered
INFO: No ilmi address registered
M8850_NY.7.PXM.a > cc 6
(session redirected)
M8850_NY.6.AXSM.a > dspilmi 1 1
Sig. rsrc Ilmi Sig Sig Ilmi S:Keepalive T:conPoll K:conPoll
Port Part State Vpi Vci Trap Interval Interval InactiveFactor
---- ---- ---- ---- ---- --- ------------ ---------- ----------
1 1 Off 0 16 On 1 5 4
M8850_NY.6.AXSM.a >
dspprfx
Display Prefix
Display the ILMI address prefixes for a port.
Cards on Which This Command Runs
PXM45
Syntax
dspprfx <portid>
Syntax Description
portid |
Identifies a PNNI physical port. The format is slot:subslot.port:subport. For a description of each field, see the section, "PNNI Format," at the beginning of the chapter. |
Related Commands
addprfx, delprfx
Attributes
Log: nolog |
State: active, standby |
Privilege: ANYUSER |
Examples
Display all ILMI address prefixes for port 4:1.1:11.
SanJose.7.PXM.a > dspprfx 4:1.1:11
ILMI Configured Port Prefix(es):
47.0091.8100.0000.0000.0ca7.9e01
88.8888.8888.0000.0000.0000.0000
SanJose.7.PXM.a >
upilmi
Up ILMI—activate ILMI on a resource partition.
Use upilmi to activate interim local management interface (ILMI) for a particular resource partition on a logical port. Before executing upilmi for the partition, you must:
1. Activate a line through the upln command and configure the line through cnfln
2. Create a logical port through the addport command
3. Add resource partitions through addrscprtn
After activating ILMI, you can configure ILMI though the cnfilmi command.
Cards on Which This Command Runs
AXSM, AXSM-E
Syntax
upilmi <ifNum> <partId>
Syntax Description
ifNum |
The ranges for logical interface (or AXSM port) number are as follows: • • |
partId |
The ranges for partition identifier are as follows: • • |
Related Commands
cnfilmi, dspilmi
Attributes
Log: log |
State: active, standby |
Privilege: GROUP1 |
uplmi
Up Local Management Interface
Activates the Local Management Interface (LMI) on the specified logical port (ifNum).
Cards on Which This Command Runs
AXSM
Syntax
uplmi <ifNum>
Syntax Description
ifNum |
The interface number of the logical port on which to activate the LMI. The range is 1-60. |
Related Commands
dnlmi
Attributes
Log: log |
State: active |
Privilege: GROUP1 |
Example
uplmi 2
Example
Determine whether ILMI is up on logical port 1, resource partition 1. If ILMI is down (or off), activate it by using the upilmi command. Note the second time you run the dspilmi command, the ILMI state now appears as "on."
M8850_NY.5.AXSME.a > dspilmi 1 1
Sig. rsrc Ilmi Sig Sig Ilmi S:Keepalive T:conPoll K:conPoll
Port Part State Vpi Vci Trap Interval Interval InactiveFactor
---- ---- ---- ---- ---- --- ------------ ---------- ----------
1 1 Off 0 16 Off 1 5 4
M8850_NY.5.AXSME.a > upilmi 1 1
Warning: connections (if any) on port could get rerouted.
Do you want to proceed (Yes/No) ? y
M8850_NY.5.AXSM.a > dspilmi 1 1
Sig. rsrc Ilmi Sig Sig Ilmi S:Keepalive T:conPoll K:conPoll
Port Part State Vpi Vci Trap Interval Interval InactiveFactor
---- ---- ---- ---- ---- --- ------------ ---------- ----------
1 1 On 0 16 Off 1 5 4
Feedback