- Preface
- Overview
- Using the Command-Line Interface
- Assigning the Switch IP Address and Default Gateway
- Configuring Cisco IOS Configuration Engine
- Administering the Switch
- Configuring Synchronous Ethernet
- Configuring the Switch External Alarms
- Configuring SDM Templates
- Configuring Switch-Based Authentication
- Configuring Interfaces
- Configuring VLANs
- Configuring Ethernet Virtual Connections (EVCs)
- Configuring Command Macros
- Configuring STP
- Configuring MSTP
- Configuring Optional Spanning-Tree Features
- Configuring Resilient Ethernet Protocol
- Configuring DHCP Features
- Configuring Dynamic ARP Inspection
- Configuring IGMP Snooping
- Configuring PIM Snooping
- Configuring IEEE 802.1x Port-Based Authentication
- Configuring IEEE 802.1ad
- Configuring Traffic Control
- Configuring CDP
- Configuring LLDP and LLDP-MED
- Configuring UDLD
- Configuring System Message Logging
- Configuring RMON
- Using the SD Flash Memory Module
- Configuring SNMP
- Configuring Embedded Event Manager
- Configuring Network Security with ACLs
- Configuring IPv6 ACLs
- Configuring Quality of Service (QoS)
- Qos on EtherChannel
- Configuring IPv6 QoS
- Hierarchical Color-Aware Policing
- Configuring Multi-level Priority Queues
- Configuring Policy-Based Routing (PBR)
- Configuring Control Plane Policing (CoPP)
- Configuring EtherChannels
- Configuring IP Unicast Routing
- Configuring IPv6 Unicast Routing
- Configuring RIPng for IPv6
- Configuring IPv6 VPN over MPLS
- Configuring Virtual Router Redundancy Protocol
- Configuring HSRP
- Configuring Cisco IOS IP SLAs Operations
- Configuring Enhanced Object Tracking
- Configuring Ethernet OAM, CFM, and E-LMI
- Configuring Y.1731 Performance Monitoring
- Configuring Ethernet Data Plane Loopback
- L2VPN Protocol-Based CLIs
- Configuring IP Multicast Routing
- Configuring Multicast VPN
- Configuring MPLS, MPLS VPN, MPLS OAM, and EoMPLS
- Multiprotocol Label Switching Load Balancing
- MPLS Traffic Engineering Bundled Interface Support
- Configuring OSPF TTL Security Check
- Configuring Switched Port Analyzer (SPAN)
- Configuring Ethernet Ring Protection
- Configuring Autonomic Networking
- Configuring Auto-IP
- Troubleshooting
- Configuring Online Diagnostics
- Supported MIBs
- Working with the Cisco IOS File System, Configuration Files, and Software Images
- Configuring MPLS Transport Profile
- CoS Marking for Pseudowires over L2 Network
- IP SLAs TWAMP Responder
- Unsupported Commands
Cisco ME 3800x and ME 3600x Switches Software Configuration Guide, Cisco IOS Release 15.4(3)S
Bias-Free Language
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
- Updated:
- June 7, 2018
Chapter: Supported MIBs
Supported MIBs
This appendix lists the supported management information base (MIBs) for this release on the Cisco ME 3800X and ME 3600X switch.
MIB List
Note The BRIDGE-MIB supports the context of a single VLAN. By default, SNMP messages using the configured community string always provide information for VLAN 1. To obtain the BRIDGE-MIB information for other VLANs, for example VLAN x, use this community string in the SNMP message: configured community string @x.
- CISCO-CDP-MIB
- CISCO-CLASS-BASED-QOS-MIB
- CISCO-ENTITY-FRU-CONTROL-MIB
- CISCO-ENTITY-SENSOR MIB
- CISCO-ETHER-CFM-MIB
- CISCO-FLASH-MIB
- CISCO-HSRP-MIB
- CISCO-IETF-PW-MIB
- CISCO-IMAGE-MIB
- CISCO-MEMORY-POOL-MIB
- CISCO-NAC-NAD-MIB
- CISCO-PAE-MIB
- CISCO-PAGP-MIB
- CISCO-PROCESS-MIB
- CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB
- CISCO-STP-EXTENSIONS-MIB
- CISCO-VTP-MIB
- DOM MIB
- ENTITY-MIB
- HOST-RESOURCES-MIB
- IF-MIB
- IF-Table
- IS-IS MIB
- LLDP MIB
- MPLS-TP MIB
- OLD-CISCO-CHASSIS-MIB
- OLD-CISCO-SYS-MIB
- OSPF-MIB
- RFC1213-MIB (Functionality is as per the agent capabilities specified in the CISCO-RFC1213-CAPABILITY.my.)
- RMON-MIB
- RMON2-MIB
- SNMPv2-MIB
- TDR-MIB
Note For information about MIB support for a specific Cisco product and release, go to the MIB Locator tool at this URL:
http://tools.cisco.com/ITDIT/MIBS/MainServlet
Using FTP to Access the MIB Files
You can obtain each MIB file by using this procedure:
Step 1 Make sure that your FTP client is in passive mode.
Note Some FTP clients do not support passive mode.
Step 2 Use FTP to access the server ftp.cisco.com .
Step 3 Log in with the username anonymous.
Step 4 Enter your e-mail username when prompted for the password.
Step 5 At the
ftp>
prompt, change directories to /pub/mibs/v1
and
/pub/mibs/v2
.
Step 6 Use the get MIB_filename command to obtain a copy of the MIB file.
Feedback