- Index
- Preface
- Overview
- Using the Command-Line Interface
- Configuring the Switch Alarms
- Assigning the Switch IP Address and Default Gateway
- Configuring Cisco IOS Configuration Engine
- Clustering Switches
- Administering the Switch
- Configuring SDM Templates
- Configuring Switch-Based Authentication
- Configuring IEEE 802.1x Port-Based Authentication
- Configuring Web-Based Authentication
- Configuring Interface Characteristics
- Configuring Smartports Macros
- Configuring VLANs
- Configuring VTP
- Configuring Voice VLAN
- Configuring Private VLANs
- Configuring IEEE 802.1Q and Layer 2 Protocol Tunneling
- Configuring STP
- Configuring MSTP
- Configuring Optional Spanning-Tree Features
- Configuring Resilient Ethernet Protocol
- Configuring Flex Links and the MAC Address-Table Move Update Feature
- Configuring DHCP Features and IP Source Guard
- Configuring Dynamic ARP Inspection
- Configuring IGMP Snooping and MVR
- Configuring Port-Based Traffic Control
- Configuring SPAN and RSPAN
- Configuring LLDP, LLDP-MED, and Wired Location Service
- Configuring CDP
- Configuring UDLD
- Configuring RMON
- Configuring System Message Logging
- Configuring SNMP
- Configuring Embedded Event Manager
- Configuring Network Security with ACLs
- Configuring QoS
- Configuring EtherChannels and Link-State Tracking
- Configuring IP Unicast Routing
- Configuring IPv6 Unicast Routing
- swipv6m
- Configuring IPv6 MLD Snooping
- Configuring IPv6 ACLs
- Configuring HSRP and VRRP
- Configuring Cisco IOS IP SLAs Operations
- Configuring Enhanced Object Tracking
- Configuring Web Cache Services By Using WCCP
- Configuring IP Multicast Routing
- Configuring MSDP
- Configuring Fallback Bridging
- Troubleshooting
- Working with the Cisco IOS File System, Configuration Files, and Software Images
- Unsupported Commands in Cisco IOS Release 15.0(2)SE
- Access Control Lists
- Archive Commands
- ARP Commands
- Boot Loader Commands
- Embedded Syslog Manager
- Debug Commands
- High Availability
- IGMP Snooping Commands
- Interface Commands
- IP SLA
- MAC Address Commands
- Miscellaneous
- NetFlow Commands
- Network Address Translation (NAT) Commands
- QoS
- RADIUS
- SNMP
- SNMPv3
- Spanning Tree
- VLAN
Unsupported Commands in Cisco IOS Release 15.0(2)SE and Later
This appendix lists some of the command-line interface (CLI) commands that appear when you enter the question mark (?) at the IE 3010 switch prompt but are not supported in this release, either because they are not tested or because of switch hardware limitations. This is not a complete list. These unsupported commands are listed by software feature and command mode:
•Network Address Translation (NAT) Commands
•QoS
•SNMP
•VLAN
Access Control Lists
Unsupported Privileged EXEC Commands
access-enable [host] [timeout minutes]
access-template [access-list-number | name] [dynamic-name] [source] [destination] [timeout minutes]
clear access-template [access-list-number | name] [dynamic-name] [source] [destination].
show access-lists rate-limit [destination]
show accounting
show ip accounting [checkpoint] [output-packets | access violations]
show ip cache [prefix-mask] [type number]
Unsupported Global Configuration Commands
access-list rate-limit acl-index {precedence | mask prec-mask}
access-list dynamic extended
Unsupported Route-Map Configuration Commands
match ip address prefix-list prefix-list-name [prefix-list-name...]
Archive Commands
Unsupported Privileged EXEC Commands
archive config
logging persistent
show archive config
show archive log
ARP Commands
Unsupported Global Configuration Commands
arp ip-address hardware-address smds
arp ip-address hardware-address srp-a
arp ip-address hardware-address srp-b
Unsupported Interface Configuration Commands
arp probe
ip probe proxy
Boot Loader Commands
Unsupported Global Configuration Commands
boot buffersize
Embedded Syslog Manager
Unsupported Global Configuration Commands
All
Unsupported Privileged EXEC Commands
All
Debug Commands
Unsupported Privileged EXEC Commands
debug platform cli-redirection main
debug platform configuration
High Availability
Unsupported SSO-Aware HSRP Commands
All
IGMP Snooping Commands
Unsupported Global Configuration Commands
ip igmp snooping tcn
Interface Commands
Unsupported Privileged EXEC Commands
show interfaces [interface-id | vlan vlan-id] [crb | fair-queue | irb | mac-accounting | precedence | irb | random-detect | rate-limit | shape]
Unsupported Global Configuration Commands
interface tunnel
Unsupported Interface Configuration Commands
transmit-interface type number
IP SLA
Unsupported MPLS Health Monitor Commands
All
Unsupported Ethernet Gatekeeper Registration Commands
All
Unsupported VoIP Call Setup Probe Commands
All
MAC Address Commands
Unsupported Privileged EXEC Commands
show mac-address-table
show mac-address-table address
show mac-address-table aging-time
show mac-address-table count
show mac-address-table dynamic
show mac-address-table interface
show mac-address-table multicast
show mac-address-table notification
show mac-address-table static
show mac-address-table vlan
show mac address-table multicast

Note Use the show ip igmp snooping groups privileged EXEC command to display Layer 2 multicast address-table entries for a VLAN.
Unsupported Global Configuration Commands
mac-address-table aging-time
mac-address-table notification
mac-address-table static
Miscellaneous
Unsupported User EXEC Commands
verify
Unsupported Privileged EXEC Commands
file verify auto
remote command
show cable-diagnostics prbs
test cable-diagnostics prbs
Unsupported Global Configuration Commands
errdisable recovery cause unicast flood
l2protocol-tunnel global drop-threshold
memory reserve critical
service compress-config
track object-number rtr
stack-mac persistent timer
logging discriminator
NetFlow Commands
Unsupported Global Configuration Commands
ip flow-aggregation cache
ip flow-cache entries
ip flow-export
Network Address Translation (NAT) Commands
Unsupported Privileged EXEC Commands
show ip nat statistics
show ip nat translations
QoS
Unsupported Global Configuration Command
priority-list
Unsupported Interface Configuration Commands
priority-group
rate-limit
Unsupported Policy-Map Configuration Command
class class-default where class-default is the class-map-name.
RADIUS
Unsupported Global Configuration Commands
aaa nas port extended
aaa authentication feature default enable
aaa authentication feature default line
aaa nas port extended
radius-server attribute nas-port
radius-server configure
radius-server extended-portnames
SNMP
Unsupported Global Configuration Commands
snmp-server enable informs
snmp-server ifindex persist
logging discriminator discr-name [[facility] [mnemonics] [msg-body] {drops string | includes string}] [severity {drops sev-num | includes sev-num}] [rate-limit msglimit]
logging buffered discriminator
SNMPv3
Unsupported 3DES Encryption Commands
All
Spanning Tree
Unsupported Global Configuration Command
spanning-tree pathcost method {long | short}
Unsupported Interface Configuration Command
spanning-tree stack-port
VLAN
Unsupported Global Configuration Command
vlan internal allocation policy {ascending | descending}
Unsupported User EXEC Commands
show running-config vlan
show vlan ifindex
vlan database
Unsupported VLAN Database Commands
vtp
vlan