Cisco IE 2000 Switch Command Reference Cisco IOS Release 15.0(2)EB

interface interface-id

Displays per-interface ACL manager information for the specified interface. The interface can be a physical interface or a VLAN.

label label - number detail

Displays per-label ACL manager information. The label - number range is 0 to 255. The keyword has this meaning:

• detail —(Optional) Displays detailed ACL manager label information.

statistics asic-number

Displays per-ASIC ACL manager information. The asic-numbe r is the port ASIC number, either 0 or 1.

usage asic-number summary

Displays per-ASIC ACL usage information. The keyword has this meaning:

• summary —(Optional) Displays usage information in a brief format.

vlan vlan-id

Displays per-VLAN ACL manager information. The vlan-id range is from 1 to 4094.

15.0(1)EY

This command was introduced.

interface-id

(Optional) Displays backup information for all interfaces or the specified interface. The interface can be a physical interface or a port channel.

dummyQ

(Optional) Displays dummy queue information.

15.0(1)EY

This command was introduced.

config-output

Displays the output of the last auto-configuration application.

default

Displays whether or not the system is running the default configuration.

running

Displays a snapshot of the backed-up running configuration on the local switch.

startup

Displays a snapshot of the backed-up startup configuration on the local switch.

15.0(1)EY

This command was introduced.

flags

Displays EtherChannel port flags.

time-stamps

Displays EtherChannel time stamps.

15.0(1)EY

This command was introduced.

interface-id

The input physical interface, the port on which the packet comes in to the switch (including type and port number).

vlan vlan-id

(Optional) Specifies the input VLAN ID. The range is 1 to 4094. If not specified, and the input interface is not a routed port, the default is 1.

src-mac

48-bit source MAC address.

dst-mac

48-bit destination MAC address.

l3protocol-id

(Optional) The Layer 3 protocol used in the packet. The number is a value 0 to 65535.

ipv6

(Optional) Specifies the IPv6 frame. This keyword is available only if the switch is running the IP services image.

sap

(Optional) Specifies the service access point (SAP) encapsulation type.

snap

(Optional) Specifies the subnetwork Access Protocol (SNAP) encapsulation type.

cos cos

(Optional) Specifies the class of service (CoS) value of the frame. The range is 0 to 7.

ip src-ip dst-ip

(Optional, but required for IP packets) Specifies the source and destination IP addresses in dotted decimal notation.

frag field

(Optional) Specifies the IP fragment field for a fragmented IP packet. The range is 0 to 65535.

dscp dscp

(Optional) Specifies the differentiated Services Code Point (DSCP) field in the IP header. The range is 0 to 63.

l4protocol-id

The numeric value of the Layer 4 protocol field in the IP header. The range is 0 to 255. For example, 47 is generic routing encapsulation (GRE), and 89 is Open Shortest Path First (OSPF). If the protocol is TCP, User Datagram Protocol (UDP), Internet Control Message Protocol (ICMP), or Internet Group Management Protocol (IGMP), you should use the appropriate keyword instead of a numeric value.

icmp icmp-type
icmp-code

Specifies the ICMP parameters. The icmp-type and icmp-code ranges are 0 to 255.

igmp igmp-version igmp-type

Specifies the IGMP parameters. The igmp-version range is 1 to 15; the igmp-type range is 0 to 15.

sctp src-port dst-port

Specifies the Stream Control Transmission Protocol (SCTP) parameters. The ranges for the SCTP source and destination ports are 0 to 65535.

tcp src-port dst-port
flags

Specifies the TCP parameters: TCP source port, destination port, and the numeric value of the TCP flags byte in the header. The src-port and dst-port ranges are 0 to 65535. The flag range is 0 to 1024.

udp src-port dst-port

Specifies the UDP parameters. The src-port and dst-port ranges are 0 to 65535.

15.0(1)EY

This command was introduced.

all

Displays all IGMP snooping platform IP multicast information.

control di

Displays IGMP snooping control entries. The keyword has this meaning:

• di —(Optional) Displays IGMP snooping control destination index entries.

counters

Displays IGMP snooping counters.

flood vlan vlan-id

Displays IGMP snooping flood information. The keyword has this meaning:

• vlan vlan-id —(Optional) Displays flood information for the specified VLAN. The range is 1 to 4094.

group ip-address

Displays the IGMP snooping multicast group information, where ip-address is the IP address of the group.

hardware

Displays IGMP snooping information loaded into hardware.

retry count | local count

Displays IGMP snooping retry information. The keywords have these meanings:

• count —(Optional) Displays only the retry count.
• local —(Optional) Displays local retry entries.

remote count

Displays remote entries. The keyword has this meaning:

• count —(Optional) Displays only the remote count.

15.0(1)EY

This command was introduced.

adjacency

Displays the platform adjacency database.

cef-idb

Displays platform information corresponding to Cisco Express Forwarding (CEF) interface descriptor block.

counts

Displays the current counts for the Layer 3 unicast databases.

dhcp

Displays the DHCP system dynamic addresses.

failed adjacency | arp A.B.C.D | route

Displays the hardware resource failures. The keywords have these meanings:

• adjacency —Displays the adjacency entries that failed to be programmed in hardware.
• arp —Displays the Address Resolution Protocol (ARP) deletions because of failure and because of retries.
• A.B.C.D— (Optional) Prefix of the ARP entries to display.
• route —Displays the route entries that failed to be programmed in hardware.

loadbalance

Displays the platform load balance database.

mpaths

Displays the Layer 3 unicast routing multipath adjacency database.

proxy

Displays the platform proxy ARP database.

route

Displays the platform route database.

standby

Displays the platform standby information.

statistics

Displays the Layer 3 unicast routing accumulated statistics.

table

Displays the platform IP version 4 (IPv4) information.

trace

Displays the platform event trace logs.

15.0(1)EY

This command was introduced.

15.0(1)EY

This command was introduced.

15.0(1)EY

This command was introduced.

detail

Displays the platform WCCP details.

label

Displays the platform WCCP labels.

15.0(1)EY

This command was introduced.

adjacency

Displays IPv6 adjacency information for the switch or for the specified IPv6 network.

ipv6-prefix

(Optional) Displays the IPv6 network. This argument must be in the form documented in RFC 2373 where the address is specified in hexadecimal using 16-bit values between colons.

backwalk adjacency | loadbalance

Displays IPv6 backwalk information.

• adjacency —Displays adjacency backwalk information.
• loadbalance —Displays backwalk load balance information.

compress ipv6-prefix/prefix length

Displays IPv6 prefix compression information.

• ipv6-prefix— The IPv6 network.
• /prefix length— The length of the IPv6 network prefix. A decimal value from 0 to 128 that shows how many of the high-order contiguous bits of the address comprise the prefix (the network portion of the address). A slash mark must precede the decimal value.

interface

Displays IPv6 interface information.

loadbalance

Displays IPv6 load balance information

mpath

Displays IPv6 multipath information

retry adjacency | route

Displays IPv6 retry information.

• adjacency —Displays IPv6 adjacency retry information.
• route —Displays IPv6 route retry information.

route

Displays IPv6 route information.

tcam

(Optional) Displays the IPv6 TCAM route table information.

detail

(Optional) Displays detailed IPv6 route information.

statistics

Displays IPv6 accumulated statistics.

table

Displays IPv6 unicast table information.

trace

Displays IPv6 unicast traces.

15.0(1)EY

This command was introduced.

acl

Displays access control list (ACL) Layer 4 operators information.

pacl port-asic

Displays port ACL Layer 4 operators information. The keyword has this meaning:

• port-asic —(Optional) Port ASIC number.

qos port-asic

Displays quality of service (QoS) Layer 4 operators information. The keyword has this meaning:

• port-asic —(Optional) QoS port ASIC number.

and-or

Displays AND-OR registers information.

map

Displays select map information.

or-and

Displays OR-AND registers information.

vcu

Displays value compare unit (VCU) register information.

15.0(1)EY

This command was introduced.

aging-array

(Optional) Displays the MAC address table aging array.

hash-table

(Optional) Displays the MAC address table hash table.

mac-address mac-address

(Optional) Displays the MAC address table MAC address information, where mac-address is the 48-bit hardware address.

vlan vlan-id

(Optional) Displays information for the specified VLAN. The range is 1 t o 4094.

15.0(1)EY

This command was introduced.

application incoming | outgoing | summary

Displays application message information. The keywords have these meanings:

• incoming —(Optional) Displays only information about incoming application messaging requests.
• outgoing —(Optional) Displays only information about incoming application messaging requests.
• summary — (Optional) Displays summary information about all application messaging requests.

hiperf [ class - number ]

Displays outgoing high-performance message information. Specifies the class-number option to display information about high-performance messages for this class number. The range is 0 to 36.

15.0(1)EY

This command was introduced.

session session-number

(Optional) Displays SPAN information for the specified SPAN session. The range is 1 to 66.

15.0(1)EY

This command was introduced.

15.0(1)EY

This command was introduced.

counters

Displays module counters information.

group-masks

Displays EtherChannel group masks information.

idbs active-idbs | deleted-idbs

Displays interface data block (IDB) information. The keywords have these meanings:

• active-idbs —Displays active IDB information.
• deleted-idbs —Displays deleted and leaked IDB information.

if-numbers

Displays interface numbers information.

link-status

Displays local port link status information.

platform-block

Displays platform port block information.

port-info interface-id

Displays port administrative and operation fields for the specified interface.

vlan info | line-state

Displays platform VLAN information. The keywords have these meanings:

• info —Displays information for active VLANs.
• line-state —Displays line-state information.

15.0(1)EY

This command was introduced.

cpu-queue-map-table
[ asic number | port number
[ asic number ]]

Displays the CPU queue-map table entries. The keywords have these meanings:

• asic number —(Optional) Displays information for the specified ASIC. The range is 0 to 1.
• port number —(Optional) Displays information for the specified port and ASIC number. The range is 0 to 27.

dest-map index number

Displays destination-map information for the specified index. The range is 0 to 65535.

etherchannel-info [ asic number | port number [ asic number ]]

Displays the contents of the EtherChannel information register. The keywords have these meanings:

• asic number —(Optional) Displays information for the specified ASIC. The range is 0 to 1.
• port number —(Optional) Displays information for the specified port and ASIC number. The range is 0 to 27, where 0 is the supervisor and 1 to 25 are the ports.

exception [ asic number | port number [ asic number ]]

Displays the exception-index register information. The keywords have these meanings:

• asic number —(Optional) Displays information for the specified ASIC. The range is 0 to 1.
• port number —(Optional) Displays information for the specified port and ASIC number. The range is 0 to 27, where 0 is the supervisor and 1 to 25 are the ports.

global-status [ asic number |
port number [ asic number ]]

Displays global and interrupt status. The keywords have these meanings:

• asic number —(Optional) Displays information for the specified ASIC. The range is 0 to 1.
• port number —(Optional) Displays information for the specified port and ASIC number. The range is 0 to 27, where 0 is the supervisor and 1 to 25 are the ports.

learning [ asic number | port number [ asic number ]]

Displays entries in the learning cache. The keywords have these meanings:

• asic number —(Optional) Displays information for the specified ASIC. The range is 0 to 1.
• port number —(Optional) Displays information for the specified port and ASIC number. The range is 0 to 27, where 0 is the supervisor and 1 to 25 are the ports.

mac-info [ asic number |
port number [ asic number ]]

Displays the contents of the MAC information register. The keywords have these meanings:

• asic number —(Optional) Displays information for the specified ASIC. The range is 0 to 1.
• port number —(Optional) Displays information for the specified port and ASIC number. The range is 0 to 27, where 0 is the supervisor and 1 to 25 are the ports.

mvid [ asic number ]

Displays the mapped VLAN ID table. The keyword has this meaning:

• asic number —(Optional) Displays information for the specified ASIC. The range is 0 to 1.

packet-info-ram [ asic number | index number [ asic number ]]

Displays the packet information RAM. The keywords have these meanings:

• asic number —(Optional) Displays information for the specified ASIC. The range is 0 to 1.
• index number —(Optional) Displays information for the specified packet RAM index number and ASIC number. The range is 0 to 63.

port-info [ asic number | port number [ asic number ]]

Displays port information register values. The keywords have these meanings:

• asic number —(Optional) Displays information for the specified ASIC. The range is 0 to 1.
• port number —(Optional) Displays information for the specified port and ASIC number. The range is 0 to 27, where 0 is the supervisor and 1 to 25 are the ports.

prog-parser [ asic number | port number [ asic number ]]

Displays the programmable parser tables. The keywords have these meanings:

• asic number —(Optional) Displays information for the specified ASIC. The range is 0 to 1.
• port number —(Optional) Displays information for the specified port and ASIC number. The range is 0 to 27, where 0 is the supervisor and 1 to 25 are the ports.

receive { buffer-queue | port-fifo | supervisor-sram } [ asic number | port number [ asic number ]]

Displays receive information. The keywords have these meanings:

• buffer-queue —Displays the buffer queue information.
• port-fifo —Displays the port-FIFO information.
• supervisor-sram —Displays the supervisor static RAM (SRAM) information.
• asic number —(Optional) Displays information for the specified ASIC. The range is 0 to 1.
• port number —(Optional) Displays information for the specified port and ASIC number. The range is 0 to 27, where 0 is the supervisor and 1 to 25 are the ports.

span [ vlan-id | asic number ]

Displays the Switched Port Analyzer (SPAN)-related information. The keywords have these meanings:

• vlan-id —(Optional) Displays information for the specified VLAN. The range is 0 to 1023.
• asic number —(Optional) Displays information for the specified ASIC. The range is 0 to 1.

stats { drop | enqueue | miscellaneous | supervisor } [ asic number | port number [ asic number ]]

Displays raw statistics for the port ASIC. The keywords have these meanings:

• drop —Displays drop statistics.
• enqueue —Displays enqueue statistics.
• miscellaneous —Displays miscellaneous statistics.
• supervisor —Displays supervisor statistics.
• asic number —(Optional) Displays information for the specified ASIC. The range is 0 to 1.
• port number —(Optional) Displays information for the specified port and ASIC number. The range is 0 to 27, where 0 is the supervisor and 1 to 25 are the ports.

transmit { port-fifo | queue | supervisor-sram } [ asic number | port number [ asic number ]]

Displays transmit information. The keywords have these meanings:

• port-fifo —Displays the contents of the port-FIFO information register.
• queue —Displays the contents of the queue information register.
• supervisor-sram —Displays supervisor SRAM information.
• asic number —(Optional) Displays information for the specified ASIC. The range is 0 to 1.
• port number —(Optional) Displays information for the specified port and ASIC number. The range is 0 to 27, where 0 is the supervisor and 1 to 25 are the ports.

vct [ asic number | port number [ asic number ]]

Displays the VLAN compression table entries for the specified ASIC or for the specified port and ASIC. The keywords have these meanings:

• asic number —(Optional) Displays information for the specified ASIC. The range is 0 to 1.
• port number —(Optional) Displays information for the specified port and ASIC number. The range is 0 to 27, where 0 is the supervisor and 1 to 25 are the ports.

version

Displays version and device type information for port ASICs.

15.0(1)EY

This command was introduced.

15.0(1)EY

This command was introduced.

label asic number

Displays QoS label maps for the specified ASIC.

(Optional) For asic number, the range is 0 to 1.

policer { parameters asic number | port alloc number asic number }

Displays policer information. The keywords have these meanings:

• parameters asic number —Displays parameter information for the specified ASIC. The range is 0 to 1.
• port alloc number asic number —Displays port allocation information for the specified port and ASIC. The port allocation range is 0 to 25. The ASIC range is 0 to 1.

15.0(1)EY

This command was introduced.

dm [ index number ]

Displays the destination map. The keyword has this meaning:

• index number —(Optional) Displays the specified index. The range is 0 to 65535.

erd [ index number ]

Displays the equal-cost-route descriptor table for the specified index. The keyword has this meaning:

• index number —(Optional) Displays the specified index. The range is 0 to 65535.

mad [ index number ]

Displays the MAC-address descriptor table for the specified index. The keyword has this meaning:

• index number —(Optional) Displays the specified index. The range is 0 to 65535.

med [ index number ]

Displays the multi-expansion descriptor table for the specified index. The keyword has this meaning:

• index number —(Optional) Displays the specified index. The range is 0 to 65535.

mod

Displays the resource-manager module information.

msm { hash-table [ vlan vlan-id ] | mac-address mac-address [ vlan vlan-id ]}

Displays the MAC-address descriptor table and the station descriptor table information. The keywords have these meanings:

• hash-table [ vlan vlan-id ]—Displays the hash table for all VLANs or the specified VLAN. The range is 1 to 4094.
• mac-address mac-address [ vlan vlan-id ]—Displays the MAC-address descriptor table for the specified MAC address represented by the 48-bit hardware address for all VLANs or the specified VLAN. The range is 1 to 4094.

sd [ index number ]

Displays the station descriptor table for the specified index. The keyword has this meaning:

• index number —(Optional) Displays the specified index. The range is 0 to 65535.

vld [ index number ]

Displays the VLAN-list descriptor table for the specified index. The keyword has this meaning:

• index number —(Optional) Displays the specified index. The range is 0 to 65535.

15.0(1)EY

This command was introduced.

status

Displays the SD Flash status.

15.0(1)EY

This command was introduced.

15.0(1)EY

This command was introduced.

synchronization [ detail | vlan vlan-id ]

Displays spanning-tree state synchronization information. The keywords have these meanings:

• detail —(Optional) Displays detailed spanning-tree information.
• vlan vlan-id —(Optional) Displays VLAN switch spanning-tree information for the specified VLAN. The range is 1 to 4094.

15.0(1)EY

This command was introduced.

vlan-id

Displays spanning-tree instance information for the specified VLAN. The range is 1 to 4094.

15.0(1)EY

This command was introduced.

handle number

Displays the TCAM handle. The range is 0 to 4294967295.

log-results

Displays the TCAM log results.

table { acl | all | equal-cost-route | ipv6 { qos | secondary } local | mac-address | multicast-expansion | qos | secondary | station | vlan-list }

Displays lookup and forwarding table information. The keywords have these meanings:

• all —Displays all the TCAM tables.
• equal-cost-route —Displays the equal-cost-route table.
• ipv6 —Displays IPv6 information.

– qos —Displays the IPv6 QoS-table information.

– secondary —Displays the IPv6 secondary-table information.

• local —Displays the local table.
• mac-address —Displays the MAC-address table.
• multicast-expansion —Displays the IPv6 multicast-expansion table.
• qos —Displays the QoS table.
• secondary —Displays the secondary table.
• station —Displays the station table.
• vlan-list —Displays the VLAN list table.

usage

Displays the CAM and forwarding table usage.

[ [ asic number [ detail [ invalid ]] | [ index number [ detail [ invalid ]] | invalid | num number [ detail [ invalid ]] | invalid ] | [ invalid ] | [ num number [ detail [ invalid ]] | invalid ]]

Displays information. The keywords have these meanings:

• asic number —Displays information for the specified ASIC device ID. The range is 0 to 15.
• detail [ invalid ]—(Optional) Displays valid or invalid details.
• index number —(Optional) Displays information for the specified TCAM table index. The range is 0 to 32768.
• num number —(Optional) Displays information for the specified TCAM table number. The range is 0 to 32768.

15.0(1)EY

This command was introduced.

misc

Displays miscellaneous VLAN module information.

mvid

Displays the mapped VLAN ID (MVID) allocation information.

prune

Displays the platform-maintained pruning database.

refcount

Displays the VLAN lock module-wise reference counts.

rpc { receive | transmit }

Displays remote procedure call (RPC) messages. The keywords have these meanings:

• receive —Displays received information.
• transmit —Displays sent information.

15.0(1)EY

This command was introduced.