When connecting a PC to the Ethernet management port, you must first assign an IP address.
Information About the Ethernet Management Port
The Ethernet management port, also referred to as the Gi0/0 or GigabitEthernet0/0 port, is a VRF (VPN routing/forwarding) interface to which you can connect a PC. You can use the Ethernet management port
instead of the device console port for network management.
Ethernet Management Port Direct Connection to a Device
Ethernet Management Port and Routing
By default, the Ethernet management port is enabled. The device cannot route packets from the Ethernet management port to
a network port, and the reverse. Even though the Ethernet management port does not support routing, you may need to enable
routing protocols on the port.
In the above figure , if the Ethernet management port and the network ports are associated with the same routing process,
the routes are propagated as follows:
The routes from the Ethernet management port are propagated through the network ports to the network.
The routes from the network ports are propagated through the Ethernet management port to the network.
Because routing is not supported between the Ethernet management port and the network ports, traffic between these ports cannot
be sent or received. If this happens, data packet loops occur between the ports, which disrupt the device and network operation.
To prevent the loops, configure route filters to avoid routes between the Ethernet management port and the network ports.
Supported Features on the Ethernet Management Port
The Ethernet management port supports these features:
Express Setup (only in device stacks)
Telnet with passwords
Secure Shell (SSH)
SNMP (only the ENTITY-MIB and the IF-MIB)
Speed—10 Mb/s, 100 Mb/s, 1000 Mb/s, and autonegotiation
Duplex mode—Full, half, and autonegotiation
Cisco Discovery Protocol (CDP)
DHCP relay agent
IPv4 and IPv6 access control lists (ACLs)
Before enabling a feature on the Ethernet management port, make sure that the feature is supported. If you try to configure
an unsupported feature on the Ethernet Management port, the feature might not work properly, and the device might fail.
How to Configure the Ethernet Management Port
Disabling and Enabling the Ethernet Management Port
Command or Action
Device# configure terminal
Enters global configuration mode.
Device(config)# interface gigabitethernet0/0
Specifies the Ethernet management port in the CLI.
Disables the Ethernet management port.
Device(config-if)# no shutdown
Enables the Ethernet management port.
Exits interface configuration mode.
show interfaces gigabitethernet0/0
Device# show interfaces gigabitethernet0/0
Displays the link status.
To find out the link status to the PC, you can monitor the LED for the Ethernet management port. The LED is green (on) when
the link is active, and the LED is off when the link is down. The LED is amber when there is a POST failure.
What to do next
Proceed to manage or configure your switch using the Ethernet management port. See the Network Management section.
Example for Configuring IP Address on Ethernet Management Interface
This example shows how to configure IP address on the management interface.
Switch#show running-config interface Gi0/0
Current configuration : 118 bytes
vrf forwarding Mgmt-vrf
ip address 192.168.247.10 255.255.0.0
Additional References for Ethernet Management Ports
See the System Management section of this guide.
See the System Management Commands section of the Command Reference (Catalyst 9500 Series Switches)
Feature History for Ethernet Management Port
This table provides release and related information for features explained in this module.
These features are available on all releases subsequent to the one they were introduced in, unless noted otherwise.
Cisco IOS XE Everest 16.5.1a
Ethernet Management Port
The Ethernet management port is a VRF interface to which you can connect a PC. You can use the Ethernet management port instead
of the device console port for network management.
Support for this feature was introduced only on the C9500-12Q, C9500-16X, C9500-24Q, C9500-40X models of the Cisco Catalyst
9500 Series Switches.
Cisco IOS XE Fuji 16.8.1a
Ethernet Management Port
Support for this feature was introduced only on the C9500-32C, C9500-32QC, C9500-48Y4C, and C9500-24Y4C models of the Cisco
Catalyst 9500 Series Switches.
Use Cisco Feature Navigator to find information about platform and software image support. To access Cisco Feature Navigator,
go to http://www.cisco.com/go/cfn.