The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
To add an ingress interface or multiple interfaces to an Intelligent Traffic Director (ITD) service, use the ingress interface command. To remove the interface or interfaces, use the no form of this command.
ingress interface interface
no ingress interface interface
interface |
Ingress interface. You can enter a single interface, multiple interfaces, or a range of interfaces (see the usage guidelines section). |
None.
ITD configuration (config-itd)
Release |
Modification |
---|---|
6.2(8) |
This command was introduced. |
You must ensure that ITD is enabled before you enter this command. You can enter the feature itd global configuration mode command to enable ITD.
You can enter a single interface, multiple interfaces, or a range of interfaces using the ingress interface command:
switch(config-itd)# ingress interface Ethernet 4/1, Ethernet 4/
switch(config-itd)# ingress interface Ethernet 4/1-10 switch(config-itd)# ingress interface vlan 1-100
Note | Before modifying the service parameters or device-group parameters, you must enter the shutdown command. Once the required parameters are modified, you should enter the no shutdown command on the service. |
This command requires the Enhanced Layer 2 Package license.
This example shows how to configure multiple ingress interfaces for the ITD service:
switch(config)# feature itd switch(config)# itd device-group dg switch(config-device-group)# node ip 20.20.20.3 switch(config-device-group)# node ip 20.20.20.4 switch(config-device-group)# node ip 20.20.20.5 switch(config-device-group)# probe icmp switch(config-device-group)# exit switch(config)# itd test switch(config-itd)# device-group dg switch(config-itd)# ingress interface Ethernet 4/1, Ethernet 4/2
This example shows how to configure a range of ingress interfaces for the ITD service:
switch(config)# feature itd switch(config)# itd device-group dg switch(config-device-group)# node ip 20.20.20.3 switch(config-device-group)# node ip 20.20.20.4 switch(config-device-group)# node ip 20.20.20.5 switch(config-device-group)# probe icmp switch(config-device-group)# exit switch(config)# itd test switch(config-itd)# device-group dg switch(config-itd)# ingress interface Ethernet 4/1-10
Command |
Description |
---|---|
device-group |
Adds an existing device group to an ITD service |
feature itd |
Enables the ITD service on the switch. |
itd device-group |
Creates an ITD device group. |
node ip |
Creates an IPv4 cluster node for ITD. |
node ipv6 |
Creates an IPv6 cluster node for ITD. |
To configure an Intelligent Traffic Director (ITD) service and to enter into ITD configuration mode, use the itd command. To remove the ITD service, use the no form of this command.
itd service-name
no itd service-name
service-name |
Name of the ITD service. You can enter up to 32 alphanumeric characters. |
Disabled.
Global configuration
Release |
Modified |
---|---|
6.2(8) |
This command was introduced. |
You must ensure that ITD is enabled before you enter this command. You can enter the feature itd global configuration mode command to enable ITD.
Note | Before modifying the service parameters or device-group parameters, you must enter the shutdown command. Once the required parameters are modified, you should enter the no shutdown command on the service. |
This command requires the Enhanced Layer 2 Package license.
This example shows how to configure an ITD service and to enter into ITD configuration mode:
switch(config)# feature itd switch(config)# itd test switch(config-itd)
Command |
Description |
---|---|
feature itd |
Enables the ITD service on the switch. |
show itd |
Displays ITD configuration information. |
To create an Intelligent Traffic Director (ITD) device group and enter device group configuration mode, use the itd device-group command. To remove the ITD device group, use the no form of this command.
itd device-group name
no itd device-group name
name |
Name of the ITD device group. You can enter up to 32 alphanumeric characters. |
Disabled.
Global configuration
Release |
Modified |
---|---|
6.2(8) |
This command was introduced. |
You must ensure that ITD is enabled before you enter this command. You can enter the feature itd global configuration mode command to enable ITD.
Note | Before modifying the service parameters or device-group parameters, you must enter the shutdown command. Once the required parameters are modified, you should enter the no shutdown command on the service. |
This command requires the Enhanced Layer 2 Package license.
This example shows how to create a device group and enter into device group configuration mode:
switch(config)# feature itd switch(config)# itd device-group dg switch(config-device-group)#
Command |
Description |
---|---|
feature itd |
Enables the ITD service on the switch. |
To enable the collection of statistics for the Intelligent Traffic Director (ITD) service, use the itd statistics command. To disable the collection of statistics, use the no form of this command.
itd statistics service-name
no itd statistics service-name
service-name |
Name of the ITD service. |
Disabled.
Global configuration
Release |
Modified |
---|---|
6.2(10) |
This command was introduced. |
You must ensure that ITD is enabled before you enter this command. You can enter the feature itd global configuration mode command to enable ITD.
This command requires the Enhanced Layer 2 Package license.
This example shows how to create a device group and enter into device group configuration mode:
switch(config)# feature itd switch(config)# itd statistics test
Command |
Description |
---|---|
feature itd |
Enables the ITD service on the switch. |
show itd statistics |
Displays the statistics for the ITD service. |