Cisco Nexus 6000 Series NX-OS Multicast Routing Command Reference

show forwarding distribution ip igmp snooping
show forwarding distribution ipv6 multicast route
show forwarding distribution multicast
show forwarding distribution multicast client
show forwarding distribution multicast outgoing-interface-list
show forwarding distribution multicast route
show forwarding ipv6 multicast route
show forwarding multicast outgoing-interface-list
show forwarding multicast route
show ip igmp event-history
show ip igmp groups
show ip igmp interface
show ip igmp local-groups
show ip igmp route
show ip igmp snooping
show ip igmp snooping event-history
show ip igmp snooping explicit-tracking
show ip igmp snooping groups
show ip igmp snooping mrouter
show ip igmp snooping querier
show ip igmp snooping statistics
show ip mroute
show ip mroute summary
show ip msdp count
show ip msdp event-history
show ip msdp mesh-group
show ip msdp peer
show ip msdp policy statistics sa-policy
show ip msdp route
show ip msdp rpf
show ip msdp sa-cache
show ip msdp route
show ip msdp sources
show ip msdp summary
show ip netstack mroute
show ip pim df
show ip pim event-history
show ip pim group-range
show ip pim interface
show ip pim neighbor
show ip pim oif-list
show ip pim policy statistics auto-rp
show ip pim policy statistics bsr
show ip pim policy statistics jp-policy
show ip pim policy statistics neighbor-policy
show ip pim policy statistics register-policy
show ip pim route
show ip pim rp
show ip pim rp-hash
show ip pim statistics
show ip pim vrf
show ip static-route
show ipv6 mld groups
show ipv6 mld local-groups
show ipv6 mroute
show ipv6 mroute summary
show ipv6 pim df
show ipv6 pim event-history
show ipv6 pim group-range
show ipv6 pim interface
show ipv6 pim neighbor
show ipv6 pim oif-list
show ipv6 pim policy statistics jp-policy
show ipv6 pim policy statistics neighbor-policy
show ipv6 pim route
show ipv6 pim rp
show ipv6 pim rp-hash
show ipv6 pim statistics
show ipv6 pim vrf
show routing ip multicast event-history
show hardware proxy layer-3 detail
show routing ipv6 multicast
show routing ipv6 multicast clients
show routing ipv6 multicast event-history
show routing multicast
show routing multicast clients
show running-config igmp
show running-config msdp
show running-config pim
show running-config pim6
show startup-config igmp
show startup-config msdp
show startup-config pim
show startup-config pim6

Show Commands

This chapter describes the Cisco NX-OS multicast routing show commands.

show forwarding distribution ip igmp snooping

To display information about Layer 2 IGMP snooping multicast Forwarding Information Base (FIB) distribution, use the show forwarding distribution ip igmp snooping command.

show forwarding distribution ip igmp snooping [ vlan vlan-id [ group group-addr [ source source-addr ]]]

Syntax Description

vlan vlan-id	(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.
group group-addr	(Optional) Specifies a group address.
source source-addr	(Optional) Specifies a source address.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about Layer 2 IGMP snooping multicast FIB distribution:

switch(config)# show forwarding distribution ip igmp snooping

Related Commands

Command	Description
test forwarding distribution perf	Tests the forwarding distribution performance of the Forwarding Information Base (FIB).

show forwarding distribution ipv6 multicast route

To display information about the multicast IPv6 FIB routes, use the show forwarding distribution ipv6 multicast route command.

show forwarding distribution ipv6 multicast route [ table table_id | vrf vrf-name ] [ group [ source ] | summary ]

Syntax Description

table table_id	(Optional) Specifies a table ID. The range is from 0x0 to 0xffffffff.
vrf vrf-name	(Optional) Specifies a virtual routing and forwarding (VRF) name. The name can be a maximum of 32 alphanumeric characters.
group	(Optional) IPv6 group address.
source	(Optional) IPv6 source address.
summary	(Optional) Specifies route counts.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the multicast IPv6 FIB routes:

switch(config)# show forwarding distribution ipv6 multicast route

IPv6 Multicast Routing table table-id:0x80000001

Total number of groups: 5

Legend:

C = Control Route

D = Drop Route

G = Local Group (directly connected receivers)

O = Drop on RPF Fail

P = Punt to supervisor

(*, ff00::/8), RPF Interface: NULL, flags: D

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 0

Null Outgoing Interface List

(*, ff01::/16), RPF Interface: NULL, flags: D

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 0

Null Outgoing Interface List

(*, ff02::/16), RPF Interface: NULL, flags: CP

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 0

Null Outgoing Interface List

(*, ff11::/16), RPF Interface: NULL, flags: D

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 0

Null Outgoing Interface List

(*, ff12::/16), RPF Interface: NULL, flags: CP

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 0

Null Outgoing Interface List

switch#

show forwarding distribution multicast

To display information about multicast Forwarding Information Base (FIB) distribution messages, use the show forwarding distribution multicast command.

show forwarding distribution multicast [ messages ]

Syntax Description

messages

(Optional) Displays message information.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about multicast distribution messages:

switch(config)# show forwarding distribution multicast

Number of Multicast FIB Processes Active: 1

Slot FIB State

1 ACTIVE

switch#

show forwarding distribution multicast client

To display information about the multicast Forwarding Information Base (FIB) distribution client, use the show forwarding distribution multicast client command.

show forwarding distribution multicast client

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the multicast FIB distribution client:

switch# show forwarding distribution multicast client

Client-name Client-id Shared Memory Name

mrib 1 mrib-mfdm

switch#

show forwarding distribution multicast outgoing-interface-list

To display information about the multicast Forwarding Information Base (FIB) outgoing interface (OIF) list, use the show forwarding distribution multicast outgoing-interface-list command.

show forwarding distribution multicast outgoing-interface-list { L2 | L3 } [ index ]

Syntax Description

L2	Specifies the Layer 2 OIF list.
L3	Specifies the Layer 3 OIF list.
index	(Optional) OIF list index.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the multicast OIF list for Layer 3:

switch# show forwarding distribution multicast outgoing-interface-list L3

show forwarding distribution multicast route

To display information about the multicast Forwarding Information Base (FIB) distribution routes, use the show forwarding distribution multicast route command.

show forwarding distribution [ ip | ipv4 ] multicast route [ table id | vrf vrf_name ] [[ group { group-addr [ mask ] | group-prefix }] [ source { source-addr [ source-mask ] | source-prefix }] | summary ]

Syntax Description

ip	(Optional) Specifies IPV4 information.
ipv4	(Optional) Specifies IPV4 information.
table id	(Optional) Specifies the multicast routing table ID. The range is from 0 to 2147483647.
vrf vrf_name	(Optional) Specifies a virtual routing and forwarding (VRF) name. The name can be a maximum of 32 alphanumeric characters.
group	(Optional) Specifies an IPv4 multicast group.
group-addr	IPv4 multicast group address.
mask	(Optional) Mask for the group address.
group-prefix	(Optional) IPv4 multicast group prefix.
source	(Optional) Specifies an IPv4 multicast source.
source-addr	IPv4 source address.
source-mask	(Optional) Mask for the group address.
source-prefix	(Optional) IPv4 multicast source prefix.
summary	(Optional) Displays the route counts.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about all the multicast FIB distribution routes:

switch(config)# show forwarding distribution multicast route

IPv4 Multicast Routing Table for table-id: 1

Total number of groups: 5

Legend:

C = Control Route

D = Drop Route

G = Local Group (directly connected receivers)

O = Drop on RPF Fail

P = Punt to supervisor

d = Decap Route

(*, 224.0.0.0/4), RPF Interface: NULL, flags: D

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 0

Null Outgoing Interface List

(*, 224.0.0.0/24), RPF Interface: NULL, flags: CP

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 0

Null Outgoing Interface List

(*, 224.0.1.39/32), RPF Interface: NULL, flags: CP

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 0

Null Outgoing Interface List

(*, 224.0.1.40/32), RPF Interface: NULL, flags: CP

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 0

Null Outgoing Interface List

(*, 232.0.0.0/8), RPF Interface: NULL, flags: D

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 0

Null Outgoing Interface List

switch#

show forwarding ipv6 multicast route

To display information about the IPv6 multicast routes, use the show forwarding ipv6 multicast route command.

show forwarding [ vrf { vrf-name | all }] ipv6 multicast route {[ group { group | group-addr } | source { source | source-addr } | module num | vrf { vrf-name | all }] | summary [ module num | vrf { vrf-name | all }]}

Syntax Description

vrf	(Optional) Displays routes for a specific virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Displays information for all VRFs.
group	(Optional) Specifies multicast IPv6 group address.
group	Multicast IPv6 group address with prefix.
group-addr	Multicast IPv6 group address.
source	Specifies multicast IPv6 source address.
source	Multicast IPv6 source address with prefix.
source-addr	Multicast IPv6 source address.
module num	(Optional) Specifies module number.
summary	Displays route counts.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.
4.1(3)	Added the group-addr and source-addr arguments.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the IPv6 multicast routes:

switch(config)# show forwarding ipv6 multicast route

IPv6 Multicast Routing table table-id:0x80000001

Total number of groups: 0

Legend:

C = Control Route

D = Drop Route

G = Local Group (directly connected receivers)

O = Drop on RPF failure

P = Punt to Supervisor

(*, ff00::/8), RPF Interface: NULL, flags: DW

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 0

Null Outgoing Interface List

(*, ff01::/16), RPF Interface: NULL, flags: DW

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 0

Null Outgoing Interface List

(*, ff02::/16), RPF Interface: NULL, flags: CPW

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 0

Null Outgoing Interface List

(*, ff11::/16), RPF Interface: NULL, flags: DW

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 0

Null Outgoing Interface List

(*, ff12::/16), RPF Interface: NULL, flags: CPW

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 0

Null Outgoing Interface List

switch(config)#

show forwarding multicast outgoing-interface-list

To display information about the multicast Forwarding Information Base (FIB) outgoing interface (OIF) list, use the show forwarding multicast outgoing-interface-list command.

show forwarding multicast outgoing-interface-list [ module num ] [ index ]

Syntax Description

module num	(Optional) Specifies the module number.
index	(Optional) OIF list index. The OIF list index is from 1 to 65535.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the multicast FIB OIF list:

switch# show forwarding multicast outgoing-interface-list

Outgoing Interface List Index: 1

Reference Count: 1

Ethernet1/5

switch#

Related Commands

Command	Description
ip igmp static-oif	Binds a multicast group to the outgoing interface (OIF).
clear ip igmp interface statistics	Clears the IGMP statistics for an interface.

show forwarding multicast route

To display information about the IPv4 Forwarding Information Base (FIB) multicast routes, use the show forwarding multicast route command.

show forwarding [ vrf { vrf-name | all }] [ ip | ipv4 ] multicast route {[ group { group-addr [ group-mask ] | group-prefix } | source { source-addr [ source-mask ] | source-prefix } | module num | vrf { vrf-name | all }] | summary [ module num | vrf { vrf-name | all }]}

Syntax Description

vrf	(Optional) Displays information for a specified virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Displays information for all VRFs.
ip	(Optional) Specifies IPv4.
ipv4	(Optional) Specifies IPv4.
group	(Optional) Specifies an IPv4 multicast group address.
group-addr	IPv4 multicast group address.
group-mask	(Optional) IPv4 multicast group address mask.
group-prefix	(Optional) IPv4 multicast group prefix.
source	(Optional) Specifies an IPv4 multicast source address.
source-addr	IPv4 multicast source address.
source-mask	IPv4 multicast source address mask.
source-prefix	IPv4 multicast source prefix.
module num	(Optional) Specifies the module number.
summary	Displays route counts.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the IPv4 multicast FIB routes:

switch# show forwarding multicast route

IPv4 Multicast Routing table table-id:1

Total number of groups: 1

Legend:

C = Control Route

D = Drop Route

G = Local Group (directly connected receivers)

O = Drop on RPF failure

P = Punt to Supervisor

W = Wildcard

d = OTV Decap route

(*, 230.0.0.0/32), RPF Interface: NULL, flags: DG

Received Packets: 0 Bytes: 0

Number of Outgoing Interfaces: 1

Outgoing Interface List Index: 1

Ethernet1/5 Outgoing Packets:0 Bytes:0

switch#

This example shows how to display the summary information about the IPv4 multicast FIB routes:

switch# show forwarding multicast route summary

IPv4 Multicast Routing Table for Context "default"

Total number of routes: 1

Total number of (*,G) routes: 1

Total number of (S,G) routes: 0

Total number of (*,G-prefix) routes: 0

Group count: 1

Prefix insert fail count: 9

switch#

Related Commands

Command	Description
clear ip mroute	Clears the multicast routing table.

show ip igmp event-history

To display information in the IGMP event history buffers, use the show ip igmp event-history command.

show ip igmp event-history { clis | debugs | errors | events | ha | igmp-internal | msgs | mtrace | policy | statistics | vrf }

Syntax Description

clis	Displays events of type CLI.
debugs	Displays events of type debug.
errors	Displays events of type error.
events	Displays events of type event.
ha	Displays events of type HA.
igmp-internal	Displays events of type IGMP internal.
msgs	Displays events of type msg.
mtrace	Displays events of type mtrace.
policy	Displays events of type policy.
statistics	Displays events of type statistics.
vrf	Displays events of type VRF.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the IGMP HA event history buffer:

switch(config)# show ip igmp event-history ha

ha events for IGMP process

2008 Apr 12 04:01:32.339950 igmp [4588]: : Router-port PSS entry for vlan 20 upd

ated [count 0]

2008 Apr 12 04:00:05.118545 igmp [4588]: : Handling existing vlans notification

2008 Apr 12 04:00:04.824730 igmp [4588]: : PSS entry for global updatedswitch(config)#

Related Commands

Command	Description
clear ip igmp event-history	Clears the contents of the IGMP event history buffers.
ip igmp event-history	Configures the size of IGMP event history buffers.

show ip igmp groups

To display information about IGMP-attached group membership, use the show ip igmp groups command.

show ip igmp groups [{ source [ group ]} | { group [ source ]}] [ ethernet slot / port | port-channel channel-number [. sub_if_number ] | vethernet veth-id | vlan vlan-id ] [ vrf { vrf-name | all }]

Syntax Description

source	Source IP address.
group	(Optional) Multicast IP address of the single group to display.
ethernet slot / port	(Optional) Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	(Optional) Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if_number	(Optional) Subinterface number. The range is from 1 to 4093.
vethernet veth-id	(Optional) Specifies the virtual Ethernet interface. The interface number can be from 1 to 1,048,575.
vlan vlan-id	(Optional) Specifies the VLAN. The range is from 1 to 4094.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

The show ip igmp route command is an alternative form of this command.

This command does not require a license.

Examples

This example shows how to display information about the IGMP-attached group membership:

switch(config)# show ip igmp groups

IGMP Connected Group Membership for VRF "default" - 0 total entries

Type: S - Static, D - Dynamic, L - Local, T - SSM Translated

Group Address Type Interface Uptime Expires Last Reporter

switch(config)#

Related Commands

Command	Description
show ip igmp route	Displays information about the IGMP-attached group membership.

show ip igmp interface

To display information about IGMP on interfaces, use the show ip igmp interface command.

show ip igmp interface { ethernet slot / port | port-channel channel-number [. sub_if_number ] | vethernet veth-id | vlan vlan-id }

show ip igmp interface [ brief ] [ vrf { vrf-name | all }]

Syntax Description

ethernet slot / port	Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if_number	Subinterface number. The range is from 1 to 4093.
vethernet veth-id	Specifies the virtual Ethernet interface. The range is from 1 to 1,048,575.
vlan vlan-id	Specifies the VLAN. The range is from 1 to 4094.
brief	(Optional) Displays one line status per interface.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.
4.1(3)	Changed output to include vPC information when IGMP is in vPC mode.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about IGMP on an interface (if IGMP is not in vPC mode, the vPC information is not displayed):

switch(config)# show ip igmp interface vlan 5

IGMP Interfaces for VRF "default"

Vlan20, Interface status: protocol-down/link-down/admin-down

IP address: 20.1.1.3, IP subnet: 20.1.1.0/24

Active querier: 0.0.0.0

Membership count: 0

Old Membership count 0

Route-queue depth: 0

IGMP version: 2, host version: 0

IGMP query interval: 125 secs, configured value: 125 secs

IGMP max response time: 10 secs, configured value: 10 secs

IGMP startup query interval: 31 secs, configured value: 31 secs

IGMP startup query count: 2

IGMP last member mrt: 1 secs

IGMP last member query count: 2

IGMP group timeout: 260 secs, configured value: 260 secs

IGMP querier timeout: 255 secs, configured value: 255 secs

IGMP unsolicited report interval: 10 secs

IGMP robustness variable: 2, configured value: 2

IGMP reporting for link-local groups: disabled

IGMP interface enable refcount: 1

IGMP interface immediate leave: disabled

IGMP Report Policy: None

IGMP State Limit: None

IGMP interface statistics:

General (sent/received):

v1-reports: 0/0

v2-queries: 0/0, v2-reports: 0/0, v2-leaves: 0/0

v3-queries: 0/0, v3-reports: 0/0

Errors:

General Queries received with invalid destination address; v2: 0, v3: 0

Checksum errors: 0, Packet length errors: 0

Packets with Local IP as source: 0, Source subnet check failures: 0

Query from non-querier:0

Report version mismatch: 0, Query version mismatch: 0

Unknown IGMP message type: 0

Invalid v1 reports: 0, Invalid v2 reports: 0, Invalid v3 reports: 0

Packets dropped due to router-alert check: 0

Interface PIM DR: No

Interface vPC CFS statistics:

DR queries sent: 0

DR queries rcvd: 0

DR queries fail: 0

DR updates sent: 0

DR updates rcvd: 0

DR updates fail: 0

switch(config)#

This example shows how to display information about IGMP on an interface in a brief format:

switch(config)# show ip igmp interface brief

IGMP Interfaces for VRF "default", count: 1

Interface IP Address IGMP Querier Membership Version

Count

Vlan20 20.1.1.3 0.0.0.0 0 v2

switch(config)#

show ip igmp local-groups

To display information about IGMP local groups, use the show ip igmp local-groups command.

show ip igmp local-groups [ ethernet slot / port | port-channel channel-number [. sub_if_number ] | vethernet veth-id | vlan vlan-id ] [ vrf { vrf-name | all }]

Syntax Description

ethernet slot / port	Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if_number	Subinterface number. The range is from 1 to 4093.
vethernet veth-id	Specifies the virtual Ethernet interface. The range is from 1 to 1,048,575.
vlan vlan-id	Specifies the VLAN. The range is from 1 to 4094.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about IGMP local groups:

switch(config)# show ip igmp local-groups

show ip igmp route

To display information about the IGMP-attached group membership, use the show ip igmp route command.

show ip igmp route [{ source [ group ]} | { group [ source ]}] [ ethernet slot / port | port-channel channel-number [. sub_if_number ] | vethernet veth-id | vlan vlan-id ] [ vrf { vrf-name | all }]

Syntax Description

source	Source IP address.
group	(Optional) Multicast IP address of single group to display.
ethernet slot / port	Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if_number	Subinterface number. The range is from 1 to 4093.
vethernet veth-id	Specifies the virtual Ethernet interface. The range is from 1 to 1,048,575.
vlan vlan-id	Specifies the VLAN. The range is from 1 to 4094.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

The show ip igmp groups command is an alternative form of this command.

This command does not require a license.

Examples

This example shows how to display information about the IGMP-attached group membership:

switch# show ip igmp route

IGMP Connected Group Membership for VRF "default" - 1 total entries

Type: S - Static, D - Dynamic, L - Local, T - SSM Translated

Group Address Type Interface Uptime Expires Last Reporter

230.0.0.0 S Ethernet1/5 00:31:47 never 0.0.0.0

switch#

Related Commands

Command	Description
show ip igmp groups	Displays information about the IGMP-attached group membership.

show ip igmp snooping

To display information about IGMP snooping, use the show ip igmp snooping command.

show ip igmp snooping [ vlan vlan-id ]

Syntax Description

vlan vlan-id

(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093. The default is all VLANs.

Command Default

Displays all VLANs.

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about IGMP snooping for a VLAN:

switch(config)# show ip igmp snooping vlan 20

IGMP Snooping information for vlan 20

IGMP snooping enabled

Optimised Multicast Flood (OMF) disabled

IGMP querier none

Switch-querier disabled

IGMPv3 Explicit tracking enabled

IGMPv2 Fast leave disabled

IGMPv1/v2 Report suppression enabled

IGMPv3 Report suppression disabled

Link Local Groups suppression enabled

Router port detection using PIM Hellos, IGMP Queries

Number of router-ports: 1

Number of groups: 0

Active ports:

Eth1/21 Po100

switch(config)#

show ip igmp snooping event-history

To display information in the IGMP snooping event history buffers, use the show ip igmp snooping event-history command.

show ip igmp snooping event-history { vpc | igmp-snoop-internal | mfdm | mfdm-sum | vlan | vlan-events }

Syntax Description

vpc	Displays the event history buffer of type virtual port channel (vPC).
igmp-snoop- internal	Displays the event history buffer of type IGMP snooping internal.
mfdm	Displays the event history buffer of type multicast FIB distribution (MFDM).
mfdm-sum	Displays the event history buffer of type MFDM sum.
vlan	Displays the event history buffer of type VLAN.
vlan-events	Displays the event history buffer of type VLAN events.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the IGMP snooping VLAN event history buffer:

switch(config)# show ip igmp snooping event-history vlan

vlan Events for IGMP snoopprocess

2008 Apr 12 06:30:47.790031 igmp [4588]: : IGMPv3 proxy report: no routers found

2008 Apr 12 06:30:47.790012 igmp [4588]: : IGMPv3 proxy report: no records to se

2008 Apr 12 06:30:47.789882 igmp [4588]: : IGMPv3 proxy report: no routers found

2008 Apr 12 06:30:47.789740 igmp [4588]: : IGMPv3 proxy report: no routers found

2008 Apr 12 06:30:47.789721 igmp [4588]: : IGMPv3 proxy report: no records to se

2008 Apr 12 06:30:47.789584 igmp [4588]: : IGMPv3 proxy report: no routers found

2008 Apr 12 06:13:17.022028 igmp [4588]: : Received a STP Topology change notifi

cation, 1 vlans

2008 Apr 12 06:13:17.022023 igmp [4588]: : Received a STP Topology change notifi

cation

2008 Apr 12 06:13:15.022294 igmp [4588]: : Received a STP Topology change notifi

cation, 1 vlans

2008 Apr 12 06:13:15.022289 igmp [4588]: : Received a STP Topology change notifi

cation

2008 Apr 12 06:13:14.662417 igmp [4588]: : Received a STP Topology change notifi

cation, 1 vlans

2008 Apr 12 06:13:14.662412 igmp [4588]: : Received a STP Topology change notifi

cation

2008 Apr 12 06:13:12.642393 igmp [4588]: : Received a STP Topology change notifi

cation, 1 vlans

2008 Apr 12 06:13:12.642388 igmp [4588]: : Received a STP Topology change notifi

cation

2008 Apr 12 06:13:11.946051 igmp [4588]: : Received a STP Topology change notifi

cation, 1 vlans

2008 Apr 12 06:13:11.946046 igmp [4588]: : Received a STP Topology change notifi

cation

<--Output truncated-->

switch(config)#

Related Commands

Command	Description
ip igmp snooping event-history	Configures the size of the IGMP snooping event history buffers.
clear ip igmp snooping event-history	Clears information in the IGMP snooping event history buffers.

show ip igmp snooping explicit-tracking

To display information about explicit tracking for IGMP snooping, use the show ip igmp snooping explicit-tracking command.

show ip igmp snooping explicit-tracking [ vlan vlan-id ]

Syntax Description

vlan vlan-id

(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.
4.2(2)	This command was changed to make the vlan argument optional.

Usage Guidelines

When you use this command without the optional vlan argument, the system displays information for all VLANs.

This command does not require a license.

Examples

This example shows how to display information about explicit tracking for IGMP snooping for VLAN 33:

switch# show ip igmp snooping explicit-tracking vlan 33

Related Commands

Command	Description
clear ip igmp snooping explicit-tracking vlan	Clears the IGMP snooping explicit host tracking information for VLANs.
ip igmp snooping explicit-tracking	Enables tracking of IGMPv3 membership reports from individual hosts for each port on a VLAN.

show ip igmp snooping groups

To display information about the group membership for IGMP snooping, use the show ip igmp snooping groups command.

show ip igmp snooping groups [{ source [ group ]} | { group [ source ]}] [ vlan vlan-id ] [ detail ]

Syntax Description

source	(Optional) Source address for route.
group	(Optional) Group address for route.
vlan vlan-id	(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.
detail	(Optional) Displays detailed information for the group.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.
4.1(2)	Arguments source and group were added.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the group membership for IGMP snooping:

switch(config)# show ip igmp snooping groups

TType: S - Static, D - Dynamic, R - Router port

Vlan Group Address Ver Type Port list

20 */* - R Vlan20

switch(config)#

show ip igmp snooping mrouter

To display the multicast routers detected by IGMP snooping, use the show ip igmp snooping mrouter command.

show ip igmp snooping mrouter [ vlan vlan-id ]

Syntax Description

vlan vlan-id

(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.
4.1(3)	Changed output to include vPC information.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the multicast routers detected by IGMP snooping:

switch(config)# show ip igmp snooping mrouter

Type: S - Static, D - Dynamic, V - vPC Peer Link

Type: S - Static, D - Dynamic, V - vPC Peer Link, I - Internal

Vlan Router-port Type Uptime Expires

20 Vlan20 I 04:16:16 never (down)

switch(config)#

show ip igmp snooping querier

To display information about IGMP snooping queriers, use the show ip igmp snooping querier command.

show ip igmp snooping querier [ vlan vlan-id ]

Syntax Description

vlan vlan-id

(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about IGMP snooping queriers:

switch(config)# show ip igmp snooping querier

show ip igmp snooping statistics

To display information about IGMP snooping statistics, use the show ip igmp snooping statistics command.

show ip igmp snooping statistics [ vlan vlan-id | global ]

Syntax Description

vlan vlan-id	(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.
global	(Optional) Specifies the global statistics.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.
4.1(3)	Changed output to include vPC information.
4.2(1)	Enhanced output for vPC information.
4.2(2)	Changed command to make the vlan argument optional and to introduce the optional global argument.

Usage Guidelines

When you use this command without any options, the system prints statistics for all VLANs.

This command does not require a license.

Examples

This example shows how to display information about IGMP snooping statistics for VLAN 1:

switch(config)# show ip igmp snooping statistics vlan 1

show ip mroute

To display information about IPv4 multicast routes, use the show ip mroute command.

show ip mroute { group | { source group } | { group [ source ]}} [ summary [ software-forwarded ]] [ vrf { vrf-name | all }]

Syntax Description

group	Group address for route.
source	Source address for route.
summary	(Optional) Displays route counts and packet rates.
software- forwarded	(Optional) Displays software-switched route counts only.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 multicast routes:

switch(config)# show ip mroute

IP Multicast Routing Table for VRF "default"

(*, 232.0.0.0/8), uptime: 04:18:55, pim ip

Incoming interface: Null, RPF nbr: 0.0.0.0

Outgoing interface list: (count: 0)

switch(config)#

The display specifies the interface established for each one and shows the router owners. In the case of the first paragraph in the display, the route owner is igmp ip pim. iod is an internal representation the device uses for the interface.

Related Commands

Command	Description
show ip mroute summary	Displays summary information about IPv4 multicast routes.

show ip mroute summary

To display summary information about IPv4 multicast routes, use the show ip mroute summary command.

show ip mroute summary [ count | software-forwarded ] [ vrf { vrf-name | all }]

show ip mroute [ group ] summary [ software-forwarded ] [ vrf { vrf-name | all }]

Syntax Description

count	(Optional) Displays only route counts.
software- forwarded	(Optional) Displays software-switched route counts only.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
group	(Optional) Specifies a group address for a route.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display summary information about IPv4 multicast routes:

switch(config)# show ip mroute summary

IP Multicast Routing Table for VRF "default"

Total number of routes: 1

Total number of (*,G) routes: 0

Total number of (S,G) routes: 0

Total number of (*,G-prefix) routes: 1

Group count: 0, rough average sources per group: 0.0

Group: 232.0.0.0/8, Source count: 0

Source packets bytes aps pps bit-rate oifs

(*,G) 0 0 0 0 0.000 bps 0

switch(config)#

This example shows how to display the number of IPv4 multicast routes:

switch# show ip mroute summary count

IP Multicast Routing Table for VRF "default"

Total number of routes: 2

Total number of (*,G) routes: 1

Total number of (S,G) routes: 0

Total number of (*,G-prefix) routes: 1

Group count: 1, rough average sources per group: 0.0

switch#

Related Commands

Command	Description
show ip mroute	Displays information about IPv4 multicast routes.

show ip msdp count

To display information about Multicast Source Discovery Protocol (MSDP) counts, use the show ip msdp count command.

show ip msdp count [ asn ] [ vrf { vrf-name | all }]

Syntax Description

asn	(Optional) Autonomous system (AS) number.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display MSDP counts:

switch(config)# show ip msdp count

show ip msdp event-history

To display information in the Multicast Source Discovery Protocol (MSDP) event history buffers, use the show ip msdp event-history command.

show ip msdp event-history { errors | msgs | statistics }

Syntax Description

errors	Displays events of type error.
msgs	Displays events of type msg.
statistics	Displays events of type statistics.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the MSDP msgs event history buffer:

switch(config)# show ip msdp event-history msgs

Related Commands

Command	Description
clear ip msdp event-history	Clears the contents of the MSDP event history buffers.
ip msdp event-history	Configures the size of MSDP event history buffers.

show ip msdp mesh-group

To display information about Multicast Source Discovery Protocol (MSDP) mesh groups, use the show ip msdp mesh-group command.

show ip msdp mesh-group [ mesh-group ] [ vrf { vrf-name | all }]

Syntax Description

mesh-group	(Optional) Mesh group name.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about MSDP mesh groups:

switch(config)# show ip msdp mesh-group

show ip msdp peer

To display information about Multicast Source Discovery Protocol (MSDP) peers, use the show ip msdp peer command.

show ip msdp peer [ peer-address ] [ vrf { vrf-name | all }]

Syntax Description

peer-address	(Optional) IP address of an MSDP peer.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about MSDP peers:

switch(config)# show ip msdp peer

show ip msdp policy statistics sa-policy

To display information about Multicast Source Discovery Protocol (MSDP) Source-Active (SA) policies, use the show ip msdp policy statistics sa-policy command.

show ip msdp policy statistics sa-policy peer-address { in | out } [ vrf { vrf-name }]

Syntax Description

peer-address	IP address of the MSDP peer for the SA policy.
in	Specifies the input policy.
out	Specifies the output policy.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about MSDP SA policies:

switch(config)# show ip msdp policy statistics sa-policy 192.168.1.10 in

show ip msdp route

To display information about the Multicast Source Discovery Protocol (MSDP) Source-Active (SA) cache, use the show ip msdp route command.

show ip msdp route [{ source [ group ]} | { group [ source ]}] [ asn ] [ peer peer ] [ detail ] [ vrf { vrf-name | all }]

Syntax Description

source	Source address for SA cache information.
group	(Optional) Group address for SA cache information.
asn	(Optional) Autonomous system (AS) number.
peer peer	(Optional) Specifies the IP address of a peer.
detail	(Optional) Displays detailed information.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

The show ip msdp sa-cache command is an alternative form of this command.

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the MSDP SA cache:

switch(config)# show ip msdp route

Related Commands

Command	Description
clear ip msdp route	Clears routes in the MSDP Source-Active cache.
show ip msdp sa-cache	Displays information about the MSDP SA cache.

show ip msdp rpf

To display information about the Multicast Source Discovery Protocol (MSDP) next-hop autonomous system (AS) on the Border Gateway Protocol (BGP) path to a rendezvous point (RP) address, use the show ip msdp rpf command.

show ip msdp rpf rp-address [ vrf { vrf-name all }]

Syntax Description

rp-address	IP address of the RP.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about MSDP reverse path forwarding (RPF) peers:

switch(config)# show ip msdp rpf 192.168.1.10

show ip msdp sa-cache

To display information about the Multicast Source Discovery Protocol (MSDP) Source-Active (SA) cache, use the show ip msdp sa-cache command.

show ip msdp sa-cache [{ source [ group ]} | { group [ source ]}] [ asn ] [ peer peer ] [ detail ] [ vrf { vrf-name | all }]

Syntax Description

source	Source address for SA cache information.
group	(Optional) Group address for SA cache information.
asn	(Optional) Autonomous system (AS) number.
peer peer	(Optional) Specifies the IP address of a peer.
detail	(Optional) Displays detailed information.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

The show ip msdp route command is an alternative form of this command.

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the MSDP SA cache:

switch(config)# show ip msdp sa-cache

Related Commands

Command	Description
clear ip msdp sa-cache	Clears routes in the MSDP Source-Active cache.
show ip msdp route	Displays information about the MSDP SA cache.

show ip msdp route

To display information about the Multicast Source Discovery Protocol (MSDP) Source-Active (SA) route cache, use the show ip msdp route command.

show ip msdp route [{ source [ group ]} | { group [ source ]}] [ asn ] [ peer peer ] [ detail ] [ vrf { vrf-name | all }]

Syntax Description

source	Source address for SA cache information.
group	(Optional) Group address for SA cache information.
asn	(Optional) Autonomous system (AS) number.
peer peer	(Optional) Specifies the IP address of a peer.
detail	(Optional) Displays detailed information.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

The show ip msdp route command is an alternative form of this command.

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the MSDP SA cache:

switch(config)# show ip msdp sa-cache

Related Commands

Command	Description
clear ip msdp sa-cache	Clears routes in the MSDP Source-Active cache.
show ip msdp route	Displays information about the MSDP SA cache.

show ip msdp sources

To display information about Multicast Source Discovery Protocol (MSDP) learned sources, use the show ip msdp sources command.

show ip msdp sources [ vrf { vrf-name | all }]

Syntax Description

vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about MSDP learned sources:

switch(config)# show ip msdp sources

show ip msdp summary

To display summary information about Multicast Source Discovery Protocol (MSDP) peers, use the show ip msdp summary command.

show ip msdp summary [ vrf { vrf-name | all }]

Syntax Description

vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display summary information about MSDP peers:

switch(config)# show ip msdp summary

show ip netstack mroute

To show IPv4 multicast routes in the Network Stack cache, use the show ip netstack mroute command.

show ip netstack mroute [ vrf vrf-name ]

Syntax Description

vrf vrf-name

(Optional) Specifies the VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display multicast routes in the Network Stack cache:

switch(config)# show ip netstack mroute

(0.0.0.0/0, 225.1.1.1/32)

Software switched packets: 1, bytes: 84

(4.1.1.2/32, 225.1.1.1/32), data-created

Software switched packets: 2, bytes: 168

(0.0.0.0/0, 225.1.1.2/32)

Software switched packets: 0, bytes: 0

(4.1.1.2/32, 225.1.1.2/32), data-created

Software switched packets: 5, bytes: 420

(0.0.0.0/0, 225.1.1.3/32)

Software switched packets: 0, bytes: 0

(4.1.1.2/32, 225.1.1.3/32), data-created

Software switched packets: 2, bytes: 168

(0.0.0.0/0, 225.1.1.4/32)

Software switched packets: 0, bytes: 0

(4.1.1.2/32, 225.1.1.4/32), data-created

Software switched packets: 2, bytes: 168

(0.0.0.0/0, 225.1.1.5/32)

Software switched packets: 0, bytes: 0

(4.1.1.2/32, 225.1.1.5/32), data-created

Software switched packets: 2, bytes: 168

(0.0.0.0/0, 226.1.1.1/32)

Software switched packets: 0, bytes: 0

(0.0.0.0/0, 226.2.2.2/32)

Software switched packets: 0, bytes: 0

(0.0.0.0/0, 232.0.0.0/8)

Software switched packets: 0, bytes: 0

switch(config)#

show ip pim df

To display information about the designated forwarders (DFs) for IPv4 Protocol Independent Multicast (PIM), use the show ip pim df command.

show ip pim df [ rp-or-group ] [ vrf { vrf-name | all }]

Syntax Description

rp-or-group	(Optional) RP or group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about PIM DFs:

switch(config)# show ip pim df

show ip pim event-history

To display information in the IPv4 Protocol Independent Multicast (PIM) event history buffers, use the show ip pim event-history command.

show ip pim event-history { errors | msgs | statistics }

Syntax Description

errors	Displays events of type error.
msgs	Displays events of type msg.
statistics	Displays events of type statistics.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the IPv4 PIM msgs event history buffer:

switch(config)# show ip pim event-history msgs

Msg events for PIM Process

1) Event:E_DEBUG, length:38, at 165671 usecs after Sat Apr 12 08:35:02 2008

[100] : nvdb: transient thread created

2) Event:E_DEBUG, length:38, at 165018 usecs after Sat Apr 12 08:35:02 2008

[100] : nvdb: create transcient thread

3) Event:E_DEBUG, length:79, at 165014 usecs after Sat Apr 12 08:35:02 2008

[100] : comp-mts-rx opc - from sap 3061 cmd pim_show_internal_event_hist_com

mand

4) Event:E_DEBUG, length:35, at 63168 usecs after Sat Apr 12 08:34:25 2008

[100] : nvdb: terminate transaction

5) Event:E_DEBUG, length:46, at 62809 usecs after Sat Apr 12 08:34:25 2008

[100] : nvdb: pim_show_df_command returned 0x0

6) Event:E_DEBUG, length:38, at 62676 usecs after Sat Apr 12 08:34:25 2008

[100] : nvdb: transient thread created

7) Event:E_DEBUG, length:38, at 61971 usecs after Sat Apr 12 08:34:25 2008

[100] : nvdb: create transcient thread

8) Event:E_DEBUG, length:62, at 61966 usecs after Sat Apr 12 08:34:25 2008

[100] : comp-mts-rx opc - from sap 3055 cmd pim_show_df_command

9) Event:E_DEBUG, length:50, at 771336 usecs after Sat Apr 12 06:14:41 2008

[100] : nvdb: _cli_send_my_if_command returned 0x0

10) Event:E_DEBUG, length:63, at 771105 usecs after Sat Apr 12 06:14:41 2008

[100] : comp-mts-rx opc - from sap 0 cmd _cli_send_my_if_command

<--Output truncated-->

switch(config)#

Related Commands

Command	Description
clear ip pim event-history	Clears the contents of the PIM event history buffers.
ip pim event-history	Configures the size of PIM event history buffers.

show ip pim group-range

To display information about the group ranges for IPv4 Protocol Independent Multicast (PIM), use the show ip pim group-range command.

show ip pim group-range [ group ] [ vrf { vrf-name | all | default | management }]

Syntax Description

group	(Optional) Group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies that all VRF entries be cleared from the IPv4 multicast routing table.
default	Specifies that the default VRF entry be cleared from the IPv4 multicast routing table.
management	Specifies that the management VRF entry be cleared from the IPv4 multicast routing table.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM group ranges:

switch(config)# show ip pim group-range

PIM Group-Range Configuration for VRF "default"

Group-range Mode RP-address Shared-tree-only range

232.0.0.0/8 SSM - -

switch(config)#

show ip pim interface

To display information about the enabled interfaces for IPv4 Protocol Independent Multicast (PIM), use the show ip pim interface command.

show ip pim interface [ brief ] [ vrf { vrf-name | all | default | management }]

show ip pim interface ethernet { slot / port | port-channel channel-number [. sub_if-number ] | vethernet veth-id | vlan vlan-id }

Syntax Description

brief	(Optional) Specifies a brief format for display.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
default	Specifies the default VRF.
management	Specifies the management VRF.
ethernet slot / port	Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if-number	(Optional) Subinterface number. The range is from 1 to 4093.
vethernet veth-id	Specifies the virtual Ethernet interface. The range is from 1 to 1,048,575.
vlan vlan-id	Specifies the VLAN. The range is from 1 to 4094.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.
5.0(2)	Information on Bidirectional Forwarding Detection (BFD) was added.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display brief information about IPv4 PIM-enabled interfaces:

switch# show ip pim interface brief

PIM Interface Status for VRF "default"

Interface IP Address PIM DR Address Neighbor Border

Count Interface

Vlan100 192.0.2.252 192.0.2.252 0 no

port-channel2000 192.0.2.1 192.0.2.1 1 no

port-channel2001 192.0.2.8 192.0.2.8 1 no

Ethernet1/26 192.0.2.2 192.0.2.2 1 no

Ethernet2/5 192.0.2.3 192.0.2.3 1 no

Ethernet2/6 192.0.2.4 192.0.2.4 1 no

Ethernet2/7 192.0.2.5 192.0.2.5 1 no

Ethernet3/11 192.0.2.6 192.0.2.6 1 no

Ethernet3/12 192.0.2.7 192.0.2.7 1 no

switch#

This example shows how to display information about PIM-enabled interfaces:

switch# show ip pim interface ethernet 2/5

PIM Interface Status for VRF "default"

Ethernet2/5, Interface status: protocol-up/link-up/admin-up

IP address: 192.0.2.3, IP subnet: 192.0.2.0/24

PIM DR: 192.0.2.3, DR's priority: 1

PIM neighbor count: 1

PIM hello interval: 30 secs, next hello sent in: 00:00:20

PIM neighbor holdtime: 105 secs

PIM configured DR priority: 1

PIM border interface: no

PIM GenID sent in Hellos: 0x36a7d6d1

PIM Hello MD5-AH Authentication: disabled

PIM Neighbor policy: none configured

PIM Join-Prune inbound policy: none configured

PIM Join-Prune outbound policy: none configured

PIM BFD enabled: no

PIM Interface Statistics, last reset: never

General (sent/received):

Hellos: 454/453, JPs: 4/0, Asserts: 0/0

Grafts: 0/0, Graft-Acks: 0/0

DF-Offers: 0/0, DF-Winners: 0/0, DF-Backoffs: 0/0, DF-Passes: 0/0

Errors:

Checksum errors: 0, Invalid packet types/DF subtypes: 0/0

Authentication failed: 0

Packet length errors: 0, Bad version packets: 0, Packets from self: 0

Packets from non-neighbors: 0

JPs received on RPF-interface: 0

(*,G) Joins received with no/wrong RP: 0/0

(*,G)/(S,G) JPs received for SSM/Bidir groups: 0/0

JPs filtered by inbound policy: 0

JPs filtered by outbound policy: 0

switch#

show ip pim neighbor

To display information about IPv4 Protocol Independent Multicast (PIM) neighbors, use the show ip pim neighbor command.

show ip pim neighbor {[ ethernet slot / port | port-channel channel-number [. sub_if-number ] | vethernet veth-id | vlan vlan-id ] | [ neighbor-addr ]} [ vrf { vrf-name | all | default | management }]

Syntax Description

ethernet slot / port	(Optional) Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	(Optional) Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if-number	(Optional) Subinterface number. The range is from 1 to 4093.
vethernet veth-id	(Optional) Specifies the virtual Ethernet interface. The range is from 1 to 1,048,575.
vlan vlan-id	Specifies the VLAN. The range is from 1 to 4094.
neighbor-addr	(Optional) IP address of a neighbor.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies that all VRF entries be cleared from the IPv4 multicast routing table.
default	Specifies that the default VRF entry be cleared from the IPv4 multicast routing table.
management	Specifies that the management VRF entry be cleared from the IPv4 multicast routing table.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.
5.0(2)	Information on Bidirectional Forwarding Detection (BFD) was added.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about PIM neighbors:

switch(config)# show ip pim neighbor

PIM Neighbor Status for VRF "default"

Neighbor Interface Uptime Expires DR Bidir- BFD

Priority Capable State

192.0.2.2 port-channel2000 03:43:40 00:01:21 1 no n/a

192.0.2.9 port-channel2001 03:43:41 00:01:35 1 no n/a

192.0.2.1 Ethernet1/26 03:43:44 00:01:33 1 no n/a

192.0.2.2 Ethernet2/5 03:43:45 00:01:34 1 no n/a

192.0.2.3 Ethernet2/6 03:43:45 00:01:19 1 no n/a

192.0.2.4 Ethernet2/7 03:43:45 00:01:39 1 no n/a

192.0.2.5 Ethernet3/11 03:43:46 00:01:35 1 no n/a

192.0.2.6 Ethernet3/12 03:43:46 00:01:34 1 no n/a

switch(config)#

show ip pim oif-list

To display information about IPv4 Protocol Independent Multicast (PIM) interfaces for a group, use the show ip pim oif-list command.

show ip pim oif-list group [ source ] [ vrf { vrf-name | all | default | management }]

Syntax Description

group	Group address.
source	(Optional) Source address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies that all VRF entries be cleared from the IPv4 multicast routing table.
default	Specifies that the default VRF entry be cleared from the IPv4 multicast routing table.
management	Specifies that the management VRF entry be cleared from the IPv4 multicast routing table.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.
4.1(3)	Changed output to include vPC information.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display IPv4 PIM interfaces for a group:

switch(config)# show ip pim oif-list 232.0.0.0

PIM OIF-List for VRF default

(*, 232.0.0.0/8)

Incoming interface: Null0, RPF nbr 0.0.0.0

Timeout interval: 66 secs left

Oif-list (count: 0):

Timeout-list (count: 0):

Immediate-list (count: 0):

Immediate-timeout-list (count: 0):

Assert-lost-list (count: 0):

switch(config)#

show ip pim policy statistics auto-rp

To display information about the Auto-RP policy statistics for IPv4 Protocol Independent Multicast (PIM), use the show ip pim policy statistics auto-rp command.

show ip pim policy statistics auto-rp { rp-candidate-policy | mapping-agent-policy } [ vrf { vrf-name | all | default | management }]

Syntax Description

rp-candidate- policy	Specifies candidate-RP messages.
mapping- agent-policy	Specifies mapping agent messages.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies that all VRF entries be cleared from the IPv4 multicast routing table.
default	Specifies that the default VRF entry be cleared from the IPv4 multicast routing table.
management	Specifies that the management VRF entry be cleared from the IPv4 multicast routing table.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM policy statistics:

switch(config)# show ip pim policy statistics auto-rp rp-candidate-policy

show ip pim policy statistics bsr

To display information about the bootstrap router (BSR) policy statistics for IPv4 Protocol Independent multicast (PIM), use the show ip pim policy statistics bsr command.

show ip pim policy statistics bsr { bsr-policy | rp-candidate-policy } [ vrf { vrf-name | all | default | management }]

Syntax Description

bsr-policy	Specifies BSR messages.
rp-candidate- policy	Specifies candidate-RP messages.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies that all VRF entries be cleared from the IPv4 multicast routing table.
default	Specifies that the default VRF entry be cleared from the IPv4 multicast routing table.
management	Specifies that the management VRF entry be cleared from the IPv4 multicast routing table.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM policy statistics:

switch(config)# show ip pim policy statistics bsr bsr-policy

show ip pim policy statistics jp-policy

To display information about the join-prune policy statistics for IPv4 Protocol Independent Multicast (PIM), use the show ip pim policy statistics jp-policy command.

show ip pim policy statistics jp-policy { ethernet slot / port | port-channel channel-number [. sub_if-number ] | vethernet veth-id | vlan vlan-id }

Syntax Description

ethernet slot / port	Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if-number	(Optional) Subinterface number. The range is from 1 to 4093.
vethernet veth-id	Specifies the virtual Ethernet interface. The range is from 1 to 1,048,575.
vlan vlan-id	Specifies the VLAN. The range is from 1 to 4094.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about PIM policy statistics:

switch(config)# show ip pim policy statistics jp-policy ethernet 2/12

show ip pim policy statistics neighbor-policy

To display information about the neighbor policy statistics for IPv4 Protocol Independent Multicast (PIM), use the show ip pim policy statistics neighbor-policy command.

show ip pim policy statistics neighbor-policy { ethernet slot / port | port-channel channel-number [. sub_if-number ] | vethernet veth-id | vlan vlan-id }

Syntax Description

ethernet slot / port	Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if-number	(Optional) Subinterface number. The range is from 1 to 4093.
vethernet veth-id	Specifies the virtual Ethernet interface. The range is from 1 to 1,048,575.
vlan vlan-id	Specifies the VLAN. The range is from 1 to 4094.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM policy statistics:

switch(config)# show ip pim policy statistics neighbor-policy ethernet 2/12

show ip pim policy statistics register-policy

To display information about the register policy statistics for IPv4 Protocol Independent Multicast (PIM), use the show ip pim policy statistics register-policy command.

show ip pim policy statistics register-policy [ vrf { vrf-name | all | default | management }]

Syntax Description

vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
default	Specifies the default VRF.
management	Specifies the management VRF.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about PIM policy statistics:

switch(config)# show ip pim policy statistics register-policy vrf all

show ip pim route

To display information about the routes for IPv4 Protocol Independent Multicast (PIM), use the show ip pim route command.

show ip pim route { source group | group [ source ]} [ vrf { vrf-name | all | default | management }]

Syntax Description

source	Source address.
group	Group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies that all VRF entries be cleared from the IPv4 multicast routing table.
default	Specifies that the default VRF entry be cleared from the IPv4 multicast routing table.
management	Specifies that the management VRF entry be cleared from the IPv4 multicast routing table.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display IPv4 PIM routes:

switch(config)# show ip pim route 232.0.0.0

PIM Routing Table for VRF "default" - 1 entries

(*, 232.0.0.0/8), expires 00:02:15

Incoming interface: Null0, RPF nbr 0.0.0.0

Oif-list: (0) 00000000, timeout-list: (0) 00000000

Immediate-list: (0) 00000000, timeout-list: (0) 00000000

Timeout-interval: 3, JP-holdtime round-up: 3

switch(config)#

show ip pim rp

To display information about the rendezvous points (RPs) for IPv4 Protocol Independent Multicast (PIM), use the show ip pim rp command.

show ip pim rp [ group ] [ vrf { vrf-name | all | default | management }]

Syntax Description

group	(Optional) Group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
default	Specifies the default VRF.
management	Specifies the management VRF.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM RPs:

switch(config)# show ip pim rp

PIM RP Status Information for VRF "default"

BSR disabled

Auto-RP disabled

BSR RP Candidate policy: None

BSR RP policy: None

Auto-RP Announce policy: None

Auto-RP Discovery policy: None

switch(config)#

show ip pim rp-hash

To display information about the RP-hash values for IPv4 Protocol Independent Multicast (PIM), use the show ip pim rp-hash command.

show ip pim rp-hash group [ vrf { vrf-name | all | default | management }]

Syntax Description

group	Group address for RP lookup.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
default	Specifies the default VRF.
management	Specifies the management VRF.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM RP-hash values:

switch(config)# show ip pim rp-hash 224.1.1.1

show ip pim statistics

To display information about the packet counter statistics for IPv4 Protocol Independent Multicast (PIM), use the show ip pim statistics command.

show ip pim statistics [ vrf { vrf-name | all | default | management }]

Syntax Description

vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
default	Specifies the default VRF.
management	Specifies the management VRF.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.
4.1(3)	Changed output to include vPC information when PIM is in vPC mode.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM statistics (if PIM is not in vPC mode, the vPC statistics are not displayed):

switch(config)# show ip pim statistics

PIM Global Counter Statistics for VRF:default, last reset: never

Registers: 0/0, Null registers: 0/0, Register-Stops: 0/0

Registers received and not RP: 0

Registers received for SSM groups: 0

BSR processing (sent/received):

Bootstraps: 0/0, Candidate-RPs: 0/0

BSs from non-neighbors: 0, BSs from border interfaces: 0

BS length errors: 0, BSs which RPF failed: 0

BSs received but not listen configured: 0

Cand-RPs from border interfaces: 0

Cand-RPs received but not listen configured: 0

Auto-RP processing (sent/received):

Auto-RP Announces: 0/0, Auto-RP Discoveries: 0/0

Auto-RP RPF failed: 0, Auto-RP from border interfaces: 0

Auto-RP invalid type: 0, Auto-RP TTL expired: 0

Auto-RP received but not listen configured: 0

General errors:

Control-plane RPF failure due to no route found: 0

Data-plane RPF failure due to no route found: 0

Data-plane no multicast state found: 0

Data-plane create route state count: 0

vPC packet stats:

assert requests sent: 0

assert requests received: 0

assert request send error: 0

assert response sent: 0

assert response received: 0

assert response send error: 0

assert stop sent: 0

assert stop received: 0

assert stop send error: 0

rpf-source metric requests sent: 0

rpf-source metric requests received: 0

rpf-source metric request send error: 0

rpf-source metric response sent: 0

rpf-source metric response received: 0

rpf-source metric response send error: 0

rpf-source metric rpf change trigger sent: 0

rpf-source metric rpf change trigger received: 0

rpf-source metric rpf change trigger send error: 0

switch(config)#

show ip pim vrf

To display information about IPv4 Protocol Independent Multicast (PIM) by virtual routing and forwarding (VRF) instance, use the show ip pim vrf command.

show ip pim vrf [ vrf-name | all | default | detail | management ]

Syntax Description

vrf-name	(Optional) VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	(Optional) Specifies all VRFs.
default	(Optional) Specifies the default VRF.
detail	(Optional) Displays detailed PIM VRF information.
management	(Optional) Specifies the management VRF.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.
5.0(2)	Information on Bidirectional Forwarding Detection (BFD) was added.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM by VRF:

switch(config)# show ip pim vrf

PIM Enabled VRF

VRF Name VRF Table Interface BFD

ID ID Count Enabled

default 1 0x00000001 1 no

switch(config)#

This example shows how to display the detailed information about IPv4 PIM by VRF:

switch# show ip pim vrf detail

PIM Enabled VRF

VRF Name VRF Table Interface BFD

ID ID Count Enabled

default 1 0x00000001 1 no

State Limit: None

Shared tree ranges: none

(S,G)-expiry timer: not configured

(S,G)-list policy: none

(S,G)-expiry timer config version 0, active version 0

Pre-build SPT for all (S,G)s in VRF: disabled

switch#

show ip static-route

To display static routes from the unicast Routing Information Base (RIB), use the show ip static-route command.

show ip static-route [ vrf { vrf-name | all | default | management }]

Syntax Description

vrf vrf-name	(Optional) Specifies the virtual routing and forwarding (VRF) context name. The name can be any case-sensitive, alphanumeric string up to 32 characters.
all	(Optional) Specifies all VRF instances.
default	(Optional) Specifies the default VRF.
management	(Optional) Specifies the management VRF.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the static routes:

switch(config)# show ip static-route

Static-route for VRF "default"(1)

IPv4 Unicast Static Routes:

Total number of routes: 0, unresolved: 0

switch(config)#

Related Commands

Command	Description
ip route	Configures a static route.

show ipv6 mld groups

To display information about the Multicast Listener Discovery (MLD) attached-group membership, use the show ipv6 mld groups command.

show ipv6 [ icmp ] mld groups [{ source [ group ]} | { group [ source ]}] [ if-type if-number ] [ vrf { vrf-name | all }]

Syntax Description

icmp	(Optional) Specifies ICMPv6 commands.
source	IPv6 source address.
group	(Optional) IPv6 multicast group address.
if-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
if-number	(Optional) Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about the MLD group membership:

switch(config)# show ipv6 mld groups

MLD Connected Group Membership for VRF "default" - 13 total entries (*, ff13::0001)

Type: Local, Interface: Ethernet2/1

Uptime/Expires: 00:00:25/00:03:54, Last Reporter: fe80::0230:48ff:fe34:0d5b

(*, ff13::0002)

Type: Local, Interface: Ethernet2/1

Uptime/Expires: 00:00:21/00:03:58, Last Reporter: fe80::0230:48ff:fe34:0d5b

(*, ff13::0003)

Type: Local, Interface: Ethernet2/1

Uptime/Expires: 00:00:22/00:03:57, Last Reporter: fe80::0230:48ff:fe34:0d5b

(*, ff13::0004)

Type: Local, Interface: Ethernet2/1

Uptime/Expires: 00:00:23/00:03:56, Last Reporter: fe80::0230:48ff:fe34:0d5b

(*, ff13::0005)

Type: Local, Interface: Ethernet2/1

Uptime/Expires: 00:00:24/00:03:55, Last Reporter: fe80::0230:48ff:fe34:0d5b

(*, ff13::0006)

Type: Local, Interface: Ethernet2/1

Uptime/Expires: 00:00:25/00:03:54, Last Reporter: fe80::0230:48ff:fe34:0d5b

(*, ff13::0007)

Type: Local, Interface: Ethernet2/1

Uptime/Expires: 00:00:27/00:03:52, Last Reporter: fe80::0230:48ff:fe34:0d5b

switch(config)#

show ipv6 mld local-groups

To display information about the local group membership for Multicast Listener Discovery (MLD), use the show ipv6 mld local-groups command.

show ipv6 [ icmp ] mld local-groups [ if-type if-number ] [ vrf { vrf-name | all }]

Syntax Description

icmp	(Optional) Specifies ICMPv6 commands.
if-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
if-number	(Optional) Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about MLD local groups:

switch(config)# show ipv6 mld local-groups

MLD Locally Joined Group Membership for VRF "default"

Group Type Interface Last Reported

(*, ff13::0001)

Local Eth2/1 00:00:55

(*, ff13::0002)

Local Eth2/1 00:00:46

(*, ff13::0003)

Local Eth2/1 00:00:54

(*, ff13::0004)

Local Eth2/1 00:00:51

(*, ff13::0005)

Local Eth2/1 00:00:49

(*, ff13::0006)

Local Eth2/1 00:00:46

(*, ff13::0007)

Local Eth2/1 00:00:54

(*, ff13::0008)

Local Eth2/1 00:00:52

(*, ff13::0009)

Local Eth2/1 00:00:50

(*, ff13::0010)

Local Eth2/1 00:00:48

(*, ff14::0001)

Local Eth2/1 00:00:46

(*, ff1e::0001)

Local Eth2/1 00:00:55

(*, ff1e::0002)

Static Lo22 03:47:54

switch(config)#

show ipv6 mroute

To display information about IPv6 multicast routes, use the show ipv6 mroute command.

show ipv6 mroute { group | { source group } | { group [ source ]}} [ summary [ software-forwarded ]] [ vrf { vrf-name | all }]

Syntax Description

group	Group address for route.
source	Source address for route.
summary	(Optional) Displays route counts and packet rates.
software- forwarded	(Optional) Displays software-switched route counts only.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about multicast routes:

switch(config)# show ipv6 mroute

IPv6 Multicast Routing Table for VRF "default"

(*, ff30::/32), uptime: 1d02h, pim6 ipv6

Incoming interface: Null, RPF nbr: 0::

Outgoing interface list: (count: 0)

switch(config)#

Related Commands

Command	Description
show ipv6 mroute summary	Displays summary information about IPv6 multicast routes.

show ipv6 mroute summary

To display summary information about IPv6 multicast routes, use the show ipv6 mroute summary command.

show ipv6 mroute summary [ count | software-forwarded ]] [ vrf { vrf-name | all }]

show ipv6 mroute { group ] summary [ software-forwarded ] [ vrf { vrf-name | all }]

Syntax Description

count	(Optional) Displays only route counts.
software- forwarded	(Optional) Displays software-switched route counts only.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
group	Specifies a group address for a route.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display summary information about multicast routes:

switch(config)# show ipv6 mroute summary

IPv6 Multicast Routing Table for VRF "default"

Total number of routes: 1

Total number of (*,G) routes: 0

Total number of (S,G) routes: 0

Total number of (*,G-prefix) routes: 1

Group count: 0, rough average sources per group: 0.0

Group: ff30::/32, Source count: 0

Source packets bytes aps pps bit-rate oifs

(*,G) 0 0 0 0 0 bps 0

switch(config)#

Related Commands

Command	Description
show ipv6 mroute	Displays information about IPv6 multicast routes.

show ipv6 pim df

To display information about the designated forwarders (DFs) for IPv6 Protocol Independent Multicast (PIM6), use the show ipv6 pim df command.

show ipv6 pim df [ rp-or-group ] [ vrf { vrf-name | all }]

Syntax Description

rp-or-group	(Optional) RP or group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 DFs:

switch(config)# show ipv6 pim df

Bidir-PIM6 Designated Forwarder Information for VRF "default"

RP Address (ordinal) RP Metric Group Range

0001::0001 (7)

[0/0] ff00::/8

Interface DF Address DF State DF Metric DF Uptime

* Lo1 0:: Lose [0/0] 00:00:02

switch(config)#

show ipv6 pim event-history

To display information in the IPv6 Protocol Independent Multicast (PIM6) event history buffers, use the show ipv6 pim event-history command.

show ipv6 pim event-history { errors | msgs | statistics }

Syntax Description

errors	Displays events of type error.
msgs	Displays events of type msg.
statistics	Displays events of type statistics.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the PIM6 msgs event history buffer:

switch(config)# show ipv6 pim event-history msgs

Note: PIM6 process currently not running

switch(config)#

Related Commands

Command	Description
clear ipv6 pim event-history	Clears the contents of the PIM6 event history buffers.
ipv6 pim event-history	Configures the size of PIM6 event history buffers.

show ipv6 pim group-range

To display information about IPv6 Protocol Independent Multicast (PIM6) group ranges, use the show ipv6 pim group-range command.

show ipv6 pim group-range [ group ] [ vrf { vrf-name | all }]

Syntax Description

group	(Optional) Group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 group ranges:

switch(config)# show ipv6 pim group-range

PIM6 Group-Range Configuration for VRF "default"

Group-range Mode RP-address Shared-tree-only range

ff30::/32 SSM - -

ff1e:abcd:def1::/96 ASM 2001:0db8:0000:abcd::0001

switch(config)#

show ipv6 pim interface

To display information about the enabled interfaces for IPv6 Protocol Independent Multicast (PIM6), use the show ipv6 pim interface command.

show ipv6 pim interface [ brief ] [ vrf { vrf-name | all }]

show ipv6 pim interface if-type if-number

Syntax Description

brief	(Optional) Specifies a brief format for display.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
if-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
if-number	(Optional) Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6-enabled interfaces:

switch(config)# show ipv6 pim interface

PIM6 Interface Status for VRF "default"

Ethernet2/12, Interface status: protocol-down/link-down/admin-down

IPv6 address: none

PIM6 DR: 0::, DR's priority: ?

PIM6 neighbor count: 0

PIM6 hello interval: 23 secs (configured 22222 ms), next hello sent in: 00:00:08

PIM6 neighbor holdtime: 81 secs

PIM6 configured DR priority: 1

PIM6 border interface: no

PIM6 GenID sent in Hellos: 0x144b4667

PIM6 Hello MD5-AH Authentication: disabled

PIM6 Neighbor policy: none configured

PIM6 Join-Prune policy: none configured

PIM6 Interface Statistics, last reset: never

General (sent/received):

Hellos: 0/0, JPs: 0/0, Asserts: 0/0

Grafts: 0/0, Graft-Acks: 0/0

DF-Offers: 0/0, DF-Winners: 0/0, DF-Backoffs: 0/0, DF-Passes: 0/0

Errors:

Checksum errors: 0, Invalid packet types/DF subtypes: 0/0

Authentication failed: 0

Packet length errors: 0, Bad version packets: 0, Packets from self: 0

Packets from non-neighbors: 0

JPs received on RPF-interface: 0

(*,G) Joins received with no/wrong RP: 0/0

(*,G)/(S,G) JPs received for SSM/Bidir groups: 0/0

JPs policy filtered: 0

switch(config)#

show ipv6 pim neighbor

To display information about IPv6 Protocol Independent Multicast (PIM6) neighbors, use the show ipv6 pim neighbor command.

show ipv6 pim neighbor {[ if-type if-number ] | [ neighbor-addr ]} [ vrf { vrf-name | all }]

Syntax Description

if-type	(Optional) Interface type. For more information, use the question mark (?) online help function.
if-number	(Optional) Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.
neighbor-addr	(Optional) IPv6 address of a neighbor.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 neighbors:

switch(config)# show ipv6 pim neighbor

PIM6 Neighbor Status for VRF "default"

Neighbor Address Interface Uptime Expires DR Bidir

Pri

fe80::0230:48ff:fe34:0d67 Eth2/1 00:00:39 00:01:34 1 yes

Secondary addresses:

0001::0002

switch(config)#

show ipv6 pim oif-list

To display information about IPv6 Protocol Independent Multicast (PIM6) interfaces for a group, use the show ipv6 pim oif-list command.

show ipv6 pim oif-list group [ source ] [ vrf { vrf-name | all }]

Syntax Description

group	Group address.
source	(Optional) Source address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display PIM6 interfaces for a group:

switch(config)# show ipv6 pim oif-list ff1e::0002

PIM6 OIF-List for VRF default

(*, ff1e::0002/128)

Incoming interface: Ethernet2/2, RPF nbr 0002::0002

Timeout interval: 45 secs left

Oif-list (count: 2):

Ethernet8/11, uptime: 00:01:18, pim6

Timeout-list (count: 0):

Immediate-list (count: 0):

Immediate-timeout-list (count: 0):

switch(config)#

show ipv6 pim policy statistics jp-policy

To display information about the join-prune policy statistics for IPv6 Protocol Independent Multicast (PIM6), use the show ipv6 pim policy statistics j-policy command.

show ipv6 pim policy statistics jp-policy if-type if-number

Syntax Description

if-type	Interface type. For more information, use the question mark (?) online help function.
if-number	Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 policy statistics:

switch(config)# show ipv6 pim policy statistics jp-policy ethernet 2/2

C: No. of comparisions, M: No. of matches

route-map rmap1 permit 10

match ipv6 multicast group ff1e::/128 C: 0 M: 0

Total accept count for policy: 2

Total reject count for policy: 0

switch(config)#

show ipv6 pim policy statistics neighbor-policy

To display information about the neighbor policy statistics for IPv6 Protocol Independent Multicast (PIM6), use the show ipv6 pim policy statistics neighbor-policy command.

show ipv6 pim policy statistics neighbor-policy if-type if-number

Syntax Description

if-type	Interface type. For more information, use the question mark (?) online help function.
if-number	Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 policy statistics:

switch(config)# show ipv6 pim policy statistics neighbor-policy ethernet 2/2

C: No. of comparisions, M: No. of matches

route-map rmap2 permit 10

match ipv6 multicast group ff1e::/128 C: 0 M: 0

Total accept count for policy: 2

Total reject count for policy: 0

switch(config)#

show ipv6 pim route

To display information about IPv6 Protocol Independent Multicast (PIM6) routes, use the show ipv6 pim route command.

show ipv6 pim route { source group | group [ source ]} [ vrf { vrf-name | all }]

Syntax Description

source	Source address.
group	Group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display PIM6 routes:

switch(config)# show ipv6 pim route

PIM6 Routing Table for VRF "default" - 1 entries

(*, ff30::/32), expires 00:02:33

Incoming interface: Null, RPF nbr 0::

Oif-list: (0) 00000000, timeout-list: (0) 00000000

Immediate-list: (0) 00000000, timeout-list: (0) 00000000

Timeout-interval: 2, JP-holdtime round-up: 3

switch(config)#

show ipv6 pim rp

To display information about IPv6 Protocol Independent Multicast (PIM) RPs, use the show ipv6 pim rp command.

show ipv6 pim rp [ group ] [ vrf { vrf-name | all }]

Syntax Description

group	(Optional) Group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 RPs:

switch(config)# show ipv6 pim rp

PIM6 RP Status Information for VRF "default"

BSR: 0::, uptime: 1d01h, expires: now,

priority: 0, hash-length: 0

Auto-RP disabled

BSR RP Candidate policy: None

BSR RP policy: None

Auto-RP Announce policy: None

Auto-RP Discovery policy: None

RP: 2001:0db8:0000:abcd::0001, (0), uptime: 1d01h, expires: 0.000000,

priority: 0, RP-source: (local), group ranges:

ff1e:abcd:def1::/96

switch(config)#

show ipv6 pim rp-hash

To display information about the RP-hash values for IPv6 Protocol Independent Multicast (PIM6), use the show ipv6 pim rp-hash command.

show ipv6 pim rp-hash group [ vrf { vrf-name | all }]

Syntax Description

group	Group address for the RP lookup.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 RP-hash values:

switch(config)# show ipv6 pim rp-hash

PIM6 Hash Information for VRF "default"

PIM6 RPs for group ff1e::0001, using hash-length: 126 from BSR: 0001::0001

RP 0002::0001, hash: 1329585728 (selected)

show ip igmp snooping explicit-tracking

----------------------------------------

switch# show ip igmp snooping explicit-tracking vlan 33

IGMPv3 Snooping Explicit-tracking information

Source/Group Intf Reporter Uptime Last-Join Expires

1.1.1.1 232.1.1.1 Eth2/1 3.3.3.3 00:01:33 00:04:27

switch(config)#

show ipv6 pim statistics

To display information about the packet counter statistics for IPv6 Protocol Independent Multicast (PIM6), use the show ipv6 pim statistics command.

show ipv6 pim statistics [ vrf { vrf-name | all }]

Syntax Description

vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 statistics:

switch(config)# show ipv6 pim statistics

PIM6 Global Counter Statistics for VRF:default, last reset: never

Registers: 0/0, Null registers: 0/0, Register-Stops: 0/0

Registers received and not RP: 0

Registers received for SSM/Bidir groups: 0/0

BSR processing (sent/received):

Bootstraps: 0/0, Candidate-RPs: 0/0

BSs from non-neighbors: 0, BSs from border interfaces: 0

BS length errors: 0, BSs which RPF failed: 0

BSs received but not listen configured: 0

Cand-RPs from border interfaces: 0

Cand-RPs received but not listen configured: 0

Auto-RP processing (sent/received):

Auto-RP Announces: 0/0, Auto-RP Discoveries: 0/0

Auto-RP RPF failed: 0, Auto-RP from border interfaces: 0

Auto-RP invalid type: 0, Auto-RP TTL expired: 0

Auto-RP received but not listen configured: 0

General errors:

Control-plane RPF failure due to no route found: 1

Data-plane RPF failure due to no route found: 0

Data-plane no multicast state found: 0

Data-plane create route state count: 0

switch(config)#

show ipv6 pim vrf

To display information about IPv6 Protocol Independent Multicast (PIM6) by virtual routing and forwarding (VRF) instance, use the show ipv6 pim vrf command.

show ipv6 pim vrf [ vrf-name | all ]

Syntax Description

vrf-name	(Optional) VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	(Optional) Specifies all VRFs.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about PIM6 by VRF:

switch(config)# show ipv6 pim vrf

switch(config)#

show routing ip multicast event-history

To display information in the IPv4 Multicast Routing Information Base (MRIB) event history buffers, use the show routing ip multicast event-history command.

show routing ip multicast event-history { cli | errors | mfdm-debugs | mfdm-stats | msgs | rib | statistics | vrf }

Syntax Description

cli	Displays the event history buffer of type CLI.
errors	Displays the event history buffer of type errors.
mfdm-debugs	Displays the event history buffer of type multicast FIB distribution (MFDM).
mfdm-stats	Displays the event history buffer of type MFDM sum.
msgs	Displays the event history buffer of type msgs.
rib	Displays the event history buffer of type RIB.
statistics	Displays information about the event history buffers.
vrf	Displays the event history buffer of type virtual routing and forwarding (VRF).

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the MRIB msgs event history buffer:

switch(config)# show routing ip multicast event-history msgs

Msg events for MRIB Process

1) Event:E_DEBUG, length:38, at 932956 usecs after Sat Apr 12 09:09:41 2008

[100] : nvdb: transient thread created

2) Event:E_DEBUG, length:38, at 932269 usecs after Sat Apr 12 09:09:41 2008

[100] : nvdb: create transcient thread

3) Event:E_DEBUG, length:75, at 932264 usecs after Sat Apr 12 09:09:41 2008

[100] : comp-mts-rx opc - from sap 3210 cmd mrib_internal_event_hist_command

4) Event:E_MTS_RX, length:60, at 362578 usecs after Sat Apr 12 09:08:51 2008

[RSP] Opc:MTS_OPC_MFDM_V4_ROUTE_STATS(75785), Id:0X000F217E, Ret:SUCCESS

Src:0x00000101/214, Dst:0x00000101/1203, Flags:None

HA_SEQNO:0X00000000, RRtoken:0x000F217B, Sync:NONE, Payloadsize:148

Payload:

0x0000: 01 00 00 00 05 00 01 00 00 04 00 00 00 00 00 00

5) Event:E_MTS_RX, length:60, at 352493 usecs after Sat Apr 12 09:07:51 2008

[RSP] Opc:MTS_OPC_MFDM_V4_ROUTE_STATS(75785), Id:0X000F188B, Ret:SUCCESS

Src:0x00000101/214, Dst:0x00000101/1203, Flags:None

HA_SEQNO:0X00000000, RRtoken:0x000F1888, Sync:NONE, Payloadsize:148

Payload:

0x0000: 01 00 00 00 05 00 01 00 00 04 00 00 00 00 00 00

6) Event:E_MTS_RX, length:60, at 342641 usecs after Sat Apr 12 09:06:51 2008

[RSP] Opc:MTS_OPC_MFDM_V4_ROUTE_STATS(75785), Id:0X000F0DF0, Ret:SUCCESS

Src:0x00000101/214, Dst:0x00000101/1203, Flags:None

HA_SEQNO:0X00000000, RRtoken:0x000F0DED, Sync:NONE, Payloadsize:148

Payload:

0x0000: 01 00 00 00 05 00 01 00 00 04 00 00 00 00 00 00

7) Event:E_MTS_RX, length:60, at 332954 usecs after Sat Apr 12 09:05:51 2008

[RSP] Opc:MTS_OPC_MFDM_V4_ROUTE_STATS(75785), Id:0X000F0493, Ret:SUCCESS

<--Output truncated-->

switch(config)#

Related Commands

Command	Description
ip routing multicast event-history	Configures the size of the IPv4 MRIB event history buffers.
clear ip routing multicast event-history	Clears information in the IPv4 MRIB event history buffers.

show hardware proxy layer-3 detail

To display detail proxy Layer 3 forwarding information, use the show hardware proxy layer-3 detail command.

show hardware proxy layer-3 detail

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

EXEC

Supported User Roles

network-admin
vdc-admin

Command History

Release	Modification
5.1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

This command applies only to Cisco Nexus 7000 Series chassis that contain an F1 Series module or an M1 Series module. This command applies when you are running either FabricPath or Ethernet interfaces.

Examples

This example shows how to display detail proxy Layer 3 forwarding information:

switch# show hardware proxy layer-3 detail

switch#

Related Commands

Command	Description
show hardware proxy layer-3 detail	Displays detailed information on the proxy Layer 3 functionality.

show routing ipv6 multicast

To display information about IPv6 multicast routes, use the show routing ipv6 multicast command.

show routing ipv6 multicast [ vrf { vrf-name | all }] {{ source group } | { group [ source ]}}

Syntax Description

vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
source	Source address for routes.
group	Group address for routes.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about IPv6 multicast routes:

switch(config)# show routing ipv6 multicast

IPv6 Multicast Routing Table for VRF "default"

switch(config)#

show routing ipv6 multicast clients

To display information about IPv6 multicast routing clients, use the show routing ipv6 multicast clients command.

show routing ipv6 multicast clients [ client-name ]

Syntax Description

client-name

(Optional) One of the following multicast routing client names:

m6rib
icmpv6
ipv6
static
pim6

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about IPv6 multicast routing clients:

switch(config)# show routing ipv6 multicast clients icmpv6

IPv6 Multicast Routing Client information

Client: icmpv6, client-id: 2, pid: 3742, mts-sap: 282

Shared-memory: icmpv6, wants notifications

Protocol is join-group owner

Join notifications: sent 1, fail 0, ack rcvd 1

Prune notifications: sent 0, fail 0, ack rcvd 0

RPF notifications: sent 0, fail 0, ack rcvd 0

Delete notifications: sent 0, fail 0, ack rcvd 0

Clear mroute notifications: sent 0, fail 0

Add route requests: rcvd 0, ack sent 0, ack fail 0

Delete route requests: rcvd 0, ack sent 0, ack fail 0

switch(config)#

show routing ipv6 multicast event-history

To display information in the IPv6 Multicast Routing Information Base (M6RIB) event history buffers, use the show routing ipv6 multicast event-history command.

show routing ipv6 multicast event-history { cli | errors | mfdm | mfdm-stats | msgs | rib | statistics | vrf }

Syntax Description

cli	Displays the event history buffer of type CLI.
errors	Displays the event history buffer of type errors.
mfdm	Displays the event history buffer of type multicast FIB distribution (MFDM).
mfdm-stats	Displays the event history buffer of type MFDM sum.
msgs	Displays the event history buffer of type msgs.
rib	Displays the event history buffer of type RIB.
statistics	Displays information about the event history buffers.
vrf	Displays the event history buffer of type virtual routing and forwarding (VRF).

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the M6RIB msgs event history buffer:

switch(config)# show routing ipv6 multicast event-history msgs

Msg events for M6RIB Process

1) Event:E_DEBUG, length:38, at 269000 usecs after Tue Jan 6 18:45:50 2009

[100] : nvdb: transient thread created

2) Event:E_DEBUG, length:38, at 267467 usecs after Tue Jan 6 18:45:50 2009

[100] : nvdb: create transcient thread

3) Event:E_DEBUG, length:76, at 267461 usecs after Tue Jan 6 18:45:50 2009

[100] : comp-mts-rx opc - from sap 3389 cmd m6rib_internal_event_hist_command

4) Event:E_MTS_RX, length:60, at 335251 usecs after Tue Jan 6 18:45:21 2009

[RSP] Opc:MTS_OPC_MFDM_V6_ROUTE_STATS(75786), Id:0X00049141, Ret:SUCCESS

Src:0x00000901/214, Dst:0x00000901/1606, Flags:None

HA_SEQNO:0X00000000, RRtoken:0x0004913F, Sync:NONE, Payloadsize:268

Payload:

0x0000: 01 00 00 80 05 00 01 00 00 08 00 00 00 00 00 00

5) Event:E_MTS_RX, length:60, at 325401 usecs after Tue Jan 6 18:44:21 2009

[RSP] Opc:MTS_OPC_MFDM_V6_ROUTE_STATS(75786), Id:0X000489A2, Ret:SUCCESS

Src:0x00000901/214, Dst:0x00000901/1606, Flags:None

HA_SEQNO:0X00000000, RRtoken:0x000489A0, Sync:NONE, Payloadsize:268

Payload:

0x0000: 01 00 00 80 05 00 01 00 00 08 00 00 00 00 00 00

6) Event:E_MTS_RX, length:60, at 315289 usecs after Tue Jan 6 18:43:21 2009

[RSP] Opc:MTS_OPC_MFDM_V6_ROUTE_STATS(75786), Id:0X00048457, Ret:SUCCESS

Src:0x00000901/214, Dst:0x00000901/1606, Flags:None

HA_SEQNO:0X00000000, RRtoken:0x00048455, Sync:NONE, Payloadsize:268

Payload:

0x0000: 01 00 00 80 05 00 01 00 00 08 00 00 00 00 00 00

7) Event:E_MTS_RX, length:60, at 305189 usecs after Tue Jan 6 18:42:21 2009

[RSP] Opc:MTS_OPC_MFDM_V6_ROUTE_STATS(75786), Id:0X00047EFD, Ret:SUCCESS

Src:0x00000901/214, Dst:0x00000901/1606, Flags:None

HA_SEQNO:0X00000000, RRtoken:0x00047EFB, Sync:NONE, Payloadsize:268

Payload:

0x0000: 01 00 00 80 05 00 01 00 00 08 00 00 00 00 00 00

8) Event:E_MTS_RX, length:60, at 295210 usecs after Tue Jan 6 18:41:21 2009

[RSP] Opc:MTS_OPC_MFDM_V6_ROUTE_STATS(75786), Id:0X0004794F, Ret:SUCCESS

Src:0x00000901/214, Dst:0x00000901/1606, Flags:None

HA_SEQNO:0X00000000, RRtoken:0x0004794D, Sync:NONE, Payloadsize:268

Payload:

0x0000: 01 00 00 80 05 00 01 00 00 08 00 00 00 00 00 00

switch(config)#

Related Commands

Command	Description
ipv6 routing multicast event-history	Configures the size of the IPv6 M6RIB event history buffers.
clear ipv6 routing multicast event-history	Clears information in the IPv6 M6RIB event history buffers.

show routing multicast

To display information about IPv4 multicast routes, use the show routing multicast command.

show routing [ ip | ipv4 ] multicast [ vrf { vrf-name | all | default | management }]
{{ source group } | { group [ source ]}}

Syntax Description

ip	(Optional) Specifies IPv4 routes.
ipv4	(Optional) Specifies IPv4 routes.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
default	Specifies the default VRF.
management	Specifies the management VRF.
source	Source address for routes.
group	Group address for routes.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 multicast routes:

switch(config)# show routing multicast

IP Multicast Routing Table for VRF "default"

(*, 232.0.0.0/8), uptime: 05:11:19, pim ip

Incoming interface: Null, RPF nbr: 0.0.0.0

Outgoing interface list: (count: 0)

switch(config)#

show routing multicast clients

To display information about IPv4 multicast routing clients, use the show routing multicast clients command.

show routing [ ip | ipv4 ] multicast clients [ client-name ]

Syntax Description

(Optional) Specifies IPv4 multicast clients.

ipv4

(Optional) Specifies IPv4 multicast clients.

client-name

(Optional) One of the following multicast routing client names:

mrib
igmp
static
msdp
ip
pim

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 multicast clients:

switch(config)# show routing multicast clients pim

IP Multicast Routing Client information

Client: pim, client-id: 5, pid: 5296, mts-sap: 310

Shared-memory: pim, Notifications: joins prunes rpf delete repopulate

Protocol is ssm owner, bidir owner, shared-only mode owner,

Join notifications: sent 1, fail 0, ack rcvd 1

Prune notifications: sent 0, fail 0, ack rcvd 0

RPF notifications: sent 0, fail 0, ack rcvd 0

Delete notifications: sent 0, fail 0, ack rcvd 0

Repopulate notifications: sent 0, fail 0, ack rcvd 0

Clear mroute notifications: sent 0, fail 0

Add route requests: rcvd 2, ack sent 2, ack fail 0

Delete route requests: rcvd 0, ack sent 0, ack fail 0

Update route requests: rcvd 0, ack sent 0, ack fail 0

MTS update route requests: rcvd 0, ack sent 0, ack fail 0

Per VRF notification markers: 1

switch(config)#

show running-config igmp

To display information about the running-system configuration for IGMP, use the show running-config igmp command.

show running-config igmp [ all ]

Syntax Description

all

(Optional) Displays configured and default information.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the IGMP running-system configuration:

switch(config)# show running-config igmp

!Command: show running-config igmp

!Time: Fri May 2 08:05:08 2008

version 5.0(3)N1(1)

interface Ethernet1/5

ip igmp static-oif 230.0.0.0

switch(config)#

show running-config msdp

To display information about the running-system configuration for Multicast Source Discovery Protocol (MSDP), use the show running-config msdp command.

show running-config msdp [ all ]

Syntax Description

all

(Optional) Displays configured and default information.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the MSDP running-system configuration:

switch(config)# show running-config msdp

!Command: show running-config msdp

!Time: Sat Apr 12 09:14:49 2008

version 5.0(3)N1(1)

feature msdp

switch(config)#

show running-config pim

To display information about the running-system configuration for IPv4 Protocol Independent Multicast (PIM), use the show running-config pim command.

show running-config pim [ all ]

Syntax Description

all

(Optional) Displays configured and default information.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the IPv4 PIM running-system configuration:

switch(config)# show running-config pim

!Command: show running-config pim

!Time: Sat Apr 12 09:15:11 2008

version 5.0(3)N1(1)

feature pim

ip pim ssm range 232.0.0.0/8

interface Vlan20

ip pim sparse-mode

switch(config)#

show running-config pim6

To display information about the running-system configuration for IPv6 Protocol Independent Multicast (PIM6), use the show running-config pim6 command.

show running-config pim6 [ all ]

Syntax Description

all

(Optional) Displays configured and default information.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about the PIM6 running-system configuration:

switch(config)# show running-config pim6

version 4.0(3)

feature pim6

ipv6 pim bidir-rp-limit 3

ipv6 pim rp-address 2001:0db8::abcd:0000:0000:0000:0001 group-list ff1e:abcd:def1::/96

ipv6 pim rp-candidate Ethernet2/11 group-list ff1e:abcd:def1::/24

ipv6 pim register-policy my_register_policy

ipv6 pim ssm range ff30::/32

ipv6 pim flush-routes

interface Ethernet2/12

ipv6 pim sparse-mode

ipv6 pim hello-interval 22222

switch(config)#

show startup-config igmp

To display information about the startup-system configuration for IGMP, use the show startup-config igmp command.

show startup-config igmp [ all ]

Syntax Description

all

(Optional) Displays configured and default information.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the IGMP startup-system configuration:

switch(config)# show startup-config igmp

show startup-config msdp

To display information about the startup-system configuration for Multicast Source Discovery Protocol (MSDP), use the show startup-config msdp command.

show startup-config msdp [ all ]

Syntax Description

all

(Optional) Displays configured and default information.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the startup-system configuration for MSDP:

switch(config)# show startup-config msdp

show startup-config pim

To display information about the startup-system configuration for IPv4 Protocol Independent Multicast (PIM), use the show startup-config pim command.

show startup-config pim [ all ]

Syntax Description

all

(Optional) Displays configured and default information.

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the startup-system configuration for IPv4 PIM:

switch(config)# show startup-config pim

show startup-config pim6

To display information about the startup-system configuration for IPv6 Protocol Independent Multicast (PIM6), use the show startup-config pim6 command.

show startup-config pim6 [ all ]

Syntax Description

all

(Optional) Displays configured and default information.

Defaults

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the Enterprise Services license.

Examples

This example shows how to display information about the startup-system configuration for PIM6:

switch(config)# show startup-config pim6

version 4.0(3)

feature pim6

ipv6 pim bidir-rp-limit 3

ipv6 pim rp-address 2001:0db8::abcd:0000:0000:0000:0001 group-list ff1e:abcd:def1::/96

ipv6 pim rp-candidate Ethernet2/11 group-list ff1e:abcd:def1::/24

ipv6 pim register-policy my_register_policy

ipv6 pim ssm range ff30::/32

ipv6 pim flush-routes

interface Ethernet2/12

ipv6 pim sparse-mode

ipv6 pim hello-interval 22222

switch(config)#

Bias-Free Language

Results

Chapter: Show Commands

Show Commands

show forwarding distribution ip igmp snooping

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

show forwarding distribution ipv6 multicast route

Syntax Description

Defaults

Command Modes

Command History

Usage Guidelines

Examples

show forwarding distribution multicast

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

show forwarding distribution multicast client

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

show forwarding distribution multicast outgoing-interface-list

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

show forwarding distribution multicast route

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

show forwarding ipv6 multicast route

Syntax Description

Defaults

Command Modes

Command History

Usage Guidelines

Examples

show forwarding multicast outgoing-interface-list

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

show forwarding multicast route

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

show ip igmp event-history

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

show ip igmp groups