Show Commands

This chapter describes the Cisco NX-OS Layer 3 interfaces show commands.

show interface brief

To display a brief summary of the interface configuration information, use the show interface brief command.

show interface brief

 
Syntax Description

This command has no arguments or keywords.

 
Command Default

None

 
Command Modes

EXEC mode

 
Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display the summary configuration information of the specified interface:

switch# show interface brief
 
--------------------------------------------------------------------------------
Ethernet VLAN Type Mode Status Reason Speed Port
Interface Ch #
--------------------------------------------------------------------------------
Eth1/1 1 eth trunk up none 10G(D) 4000
Eth1/2 1 eth trunk up none 10G(D) 4000
Eth1/3 1 eth trunk up none 10G(D) 4000
Eth1/4 1 eth trunk up none 10G(D) 4000
Eth1/5 1 eth access down SFP not inserted 10G(D) --
Eth1/6 1 eth access down SFP not inserted 10G(D) --
Eth1/7 1 eth trunk up none 10G(D) 10
Eth1/8 1 eth trunk up none 10G(D) 10
Eth1/9 1 eth trunk up none 10G(D) 10
Eth1/10 1 eth trunk up none 10G(D) 10
Eth1/11 1 eth access down SFP not inserted 10G(D) --
Eth1/12 1 eth access down SFP not inserted 10G(D) --
Eth1/13 1 eth access down SFP not inserted 10G(D) --
Eth1/14 1 eth access down SFP not inserted 10G(D) --
Eth1/15 1 eth access down SFP not inserted 10G(D) --
Eth1/16 1 eth access down SFP not inserted 10G(D) --
Eth1/17 1 eth access down SFP not inserted 10G(D) --
Eth1/18 1 eth access down SFP not inserted 10G(D) --
Eth1/19 1 eth access down SFP not inserted 10G(D) --
Eth1/20 1 eth access down SFP not inserted 10G(D) --
Eth1/21 1 eth access down SFP not inserted 10G(D) --
Eth1/22 1 eth access down SFP not inserted 10G(D) --
Eth1/23 1 eth access down Link not connected 10G(D) --
Eth1/24 1 eth access down Link not connected 10G(D) --
Eth1/25 1 eth access down SFP not inserted 10G(D) --
Eth1/26 1 eth access down SFP not inserted 10G(D) --
Eth1/27 1 eth access down SFP not inserted 10G(D) --
Eth1/28 1 eth access down SFP not inserted 10G(D) --
Eth1/29 1 eth access down SFP not inserted 10G(D) --
Eth1/30 1 eth access down SFP not inserted 10G(D) --
Eth1/31 1 eth access down SFP not inserted 10G(D) --
Eth1/32 1 eth access down SFP not inserted 10G(D) --
Eth1/33 1 eth access down SFP not inserted 10G(D) --
Eth1/34 1 eth access down SFP not inserted 10G(D) --
Eth1/35 1 eth access down SFP not inserted 10G(D) --
Eth1/36 1 eth access down SFP not inserted 10G(D) --
Eth1/37 1 eth access down SFP not inserted 10G(D) --
Eth1/38 1 eth access down SFP not inserted 10G(D) --
Eth1/39 1 eth access down SFP not inserted 10G(D) --
Eth1/40 1 eth trunk up none 10G(D) --
Eth2/1 1 eth access down SFP not inserted 10G(D) --
Eth2/2 1 eth access up none 10G(D) --
Eth2/3 1 eth access down SFP not inserted 10G(D) --
Eth2/4 1 eth access up none 10G(D) --
Eth2/5 1 eth access up none 10G(D) --
Eth2/6 1 eth access down SFP not inserted 10G(D) --
 
--------------------------------------------------------------------------------
Port-channel VLAN Type Mode Status Reason Speed Protocol
Interface
--------------------------------------------------------------------------------
Po10 1 eth trunk up none a-10G(D) lacp
Po4000 1 eth trunk up none a-10G(D) lacp
 
--------------------------------------------------------------------------------
Port VRF Status IP Address Speed MTU
--------------------------------------------------------------------------------
mgmt0 -- up 192.168.10.37 100 1500
 
-------------------------------------------------------------------------------
Interface Secondary VLAN(Type) Status Reason
-------------------------------------------------------------------------------
Vlan1 -- down Administratively down
 
switch#
 

This example shows how to display the summary configuration information of interfaces, including routed interfaces:

switch# show interface brief
 
--------------------------------------------------------------------------------
Ethernet VLAN Type Mode Status Reason Speed Port
Interface Ch #
--------------------------------------------------------------------------------
Eth1/1 1 eth access down Link not connected 10G(D) --
Eth1/2 1 eth trunk up none 10G(D) --
Eth1/3 1 eth access down SFP not inserted 10G(D) --
Eth1/4 1 eth access down SFP not inserted 10G(D) --
Eth1/5 -- eth routed up none 10G(D) --
Eth1/5.2 -- eth routed down Configuration Incomplete 10G(D) --
Eth1/6 1 eth access up none 10G(D) --
Eth1/7 1 eth access up none 10G(D) --
Eth1/8 1 eth trunk up none 10G(D) 100
Eth1/9 1 eth access up none 10G(D) --
Eth1/10 1 eth access down Link not connected 10G(D) --
Eth1/11 1 eth access down SFP not inserted 10G(D) --
Eth1/12 1 eth access down SFP not inserted 10G(D) --
Eth1/13 1 eth access down SFP not inserted 10G(D) --
Eth1/14 1 eth access down SFP not inserted 10G(D) --
Eth1/15 1 eth access down SFP not inserted 10G(D) --
Eth1/16 1 eth access down SFP not inserted 10G(D) --
Eth1/17 1 eth access up none 10G(D) --
Eth1/18 1 eth access up none 10G(D) --
Eth1/19 1 eth fabric up none 10G(D) --
Eth1/20 1 eth access down Link not connected 10G(D) --
Eth1/21 1 eth access up none 10G(D) --
Eth1/22 1 eth access down Link not connected 10G(D) --
Eth1/23 1 eth access down SFP not inserted 10G(D) --
Eth1/24 1 eth access down SFP not inserted 10G(D) --
Eth1/25 1 eth access down Link not connected 10G(D) --
Eth1/26 1 eth access down SFP not inserted 10G(D) --
Eth1/27 1 eth access down SFP not inserted 10G(D) --
Eth1/28 1 eth access down SFP not inserted 10G(D) --
Eth1/29 1 eth access down Link not connected 10G(D) --
Eth1/30 1 eth access down SFP not inserted 10G(D) --
Eth1/31 1 eth access down SFP not inserted 10G(D) --
Eth1/32 1 eth access up none 10G(D) --
 
--------------------------------------------------------------------------------
Port-channel VLAN Type Mode Status Reason Speed Protocol
Interface
--------------------------------------------------------------------------------
Po100 1 eth trunk up none a-10G(D) none
 
--------------------------------------------------------------------------------
Port VRF Status IP Address Speed MTU
--------------------------------------------------------------------------------
mgmt0 -- up 172.29.231.33 1000 1500
 
-------------------------------------------------------------------------------
Interface Secondary VLAN(Type) Status Reason
-------------------------------------------------------------------------------
Vlan1 -- up --
Vlan100 -- up --
 
--------------------------------------------------------------------------------
Ethernet VLAN Type Mode Status Reason Speed Port
Interface Ch #
--------------------------------------------------------------------------------
Eth100/1/1 1 eth access up none 10G(D) --
Eth100/1/2 1 eth access down Link not connected auto(D) --
Eth100/1/3 1 eth access up none 10G(D) --
Eth100/1/4 1 eth access down Link not connected auto(D) --
Eth100/1/5 1 eth access down Link not connected auto(D) --
Eth100/1/6 1 eth access down Link not connected auto(D) --
Eth100/1/7 1 eth access down Link not connected auto(D) --
Eth100/1/8 1 eth access down Link not connected auto(D) --
Eth100/1/9 1 eth access down Link not connected auto(D) --
Eth100/1/10 1 eth access up none 10G(D) --
Eth100/1/11 1 eth access down Link not connected auto(D) --
Eth100/1/12 1 eth access down Link not connected auto(D) --
Eth100/1/13 1 eth access down Link not connected auto(D) --
Eth100/1/14 1 eth access down Link not connected auto(D) --
Eth100/1/15 1 eth access up none 10G(D) --
Eth100/1/16 1 eth access down Link not connected auto(D) --
 
--------------------------------------------------------------------------------
Interface Status Description
--------------------------------------------------------------------------------
Lo10 up --
switch#
 

Note the following in the above display:

  • Ethernet 1/5 is a Layer 3-ready interface. The following fields in the display help identify an interface as a configured Layer 3 interface:

Mode—routed

Status—up

Reason—none

  • Ethernet 1/5.2 is a Layer 3 subinterface; however, the interface is not ready for Layer 3 configuration (Status—down).
  • Interface Lo10 is a Layer 3 loopback interface.

This example shows how to display a brief summary of interfaces configured as FabricPath interfaces on a switch that runs Cisco Nexus 6000 Release 6.0(2)N1(1):

switch# show interface brief
--------------------------------------------------------------------------------
Ethernet VLAN Type Mode Status Reason Speed Port
Interface Ch#
--------------------------------------------------------------------------------
Eth1/1 1 eth access down SFP not inserted 1000(D) --
Eth1/2 -- eth routed down SFP not inserted 1000(D) --
Eth1/3 1 eth access down SFP not inserted 10G(D) --
Eth1/4 1 eth access down SFP not inserted 10G(D) --
Eth1/5 1 eth f-path down SFP not inserted 10G(D) --
Eth1/6 1 eth access down Link not connected 10G(D) --
Eth1/7 1 eth fabric down Link not connected 10G(D) --
Eth1/8 1 eth access down SFP not inserted 10G(D) --
Eth1/9 1 eth access down SFP not inserted 10G(D) --
Eth1/10 1 eth access down SFP not inserted 10G(D) --
Eth1/11 1 eth access down SFP not inserted 10G(D) --
Eth1/12 1 eth access down SFP not inserted 10G(D) --
Eth1/13 1 eth access down SFP not inserted 10G(D) --
Eth1/14 1 eth access down SFP not inserted 10G(D) --
Eth1/15 1 eth pvlan up none 1000(D) --
Eth1/16 1 eth access down SFP not inserted 10G(D) --
Eth1/17 1 eth access down SFP not inserted 10G(D) --
switch#
 

In the above display, Ethernet 1/5 has the mode shown as “f-path” indicating that it has been configured as a FabricPath port.

 
Related Commands

Command
Description

interface ethernet

Configures an Ethernet IEEE 802.3 interface.

 

show interface ethernet

To display information about the interface configuration, use the show interface ethernet command.

show interface ethernet slot / port [. subintf-port-no ] [ brief | counters | description | status | switchport ]

 
Syntax Description

slot / port

Ethernet interface slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.

.

(Optional) Specifies the subinterface separator.

Note This keyword applies to Layer 3 interfaces.

subintf-port-no

(Optional) Port number for the subinterface. The range is from 1 to 48.

Note This argument applies to Layer 3 interfaces.

brief

(Optional) Displays brief information about the interfaces.

counters

(Optional) Displays information about the counters configured on an interface.

description

(Optional) Displays the description of an interface configuration.

status

(Optional) Displays the operational state of the interface.

switchport

(Optional) Displays the switchport information of an interface.

 
Command Default

Displays all information for the interface.

 
Command Modes

EXEC mode

 
Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display the detailed configuration of the specified interface:

switch# show interface ethernet 1/1
Ethernet1/1 is up
Hardware: 1000/10000 Ethernet, address: 000d.ece7.df48 (bia 000d.ece7.df48)
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is fex-fabric
full-duplex, 10 Gb/s, media type is 1/10g
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
Last link flapped 09:03:57
Last clearing of "show interface" counters never
30 seconds input rate 2376 bits/sec, 0 packets/sec
30 seconds output rate 1584 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
input rate 1.58 Kbps, 0 pps; output rate 792 bps, 0 pps
RX
0 unicast packets 10440 multicast packets 0 broadcast packets
10440 input packets 11108120 bytes
0 jumbo packets 0 storm suppression packets
0 runts 0 giants 0 CRC 0 no buffer
0 input error 0 short frame 0 overrun 0 underrun 0 ignored
0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
0 input with dribble 0 input discard
0 Rx pause
TX
0 unicast packets 20241 multicast packets 105 broadcast packets
20346 output packets 7633280 bytes
0 jumbo packets
0 output errors 0 collision 0 deferred 0 late collision
0 lost carrier 0 no carrier 0 babble
0 Tx pause
1 interface resets
 
switch#
 

This example shows how to display the counters configured on a specified interface:

switch# show interface ethernet 1/1 counters
 
--------------------------------------------------------------------------------
Port InOctets InUcastPkts InMcastPkts InBcastPkts
--------------------------------------------------------------------------------
Eth1/1 17193136 0 16159 0
--------------------------------------------------------------------------------
Port OutOctets OutUcastPkts OutMcastPkts OutBcastPkts
--------------------------------------------------------------------------------
Eth1/1 11576758 0 28326 106
switch#
 

This example shows how to display the detailed configuration information of a specified subinterface:

switch# show interface ethernet 1/5.2
Ethernet1/5.2 is up
Hardware: 1000/10000 Ethernet, address: 0005.73a6.1dbc (bia 0005.73a6.1d6c)
Description: Eth 1/5.2 subinterfaces
Internet Address is 192.0.0.3/24
MTU 1500 bytes, BW 1500 Kbit, DLY 2000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 100
EtherType is 0x8100
 
switch#
 

This example shows how to display the brief configuration information of a specified subinterface:

switch# show interface ethernet 1/5.2 brief
 
--------------------------------------------------------------------------------
Ethernet VLAN Type Mode Status Reason Speed Port
Interface Ch #
--------------------------------------------------------------------------------
Eth1/5.2 100 eth routed up none 10G(D) --
switch#
 

This example shows how to display the purpose of a specified subinterface:

switch# show interface ethernet 1/5.2 description
 
-------------------------------------------------------------------------------
Port Type Speed Description
-------------------------------------------------------------------------------
Eth1/5.2 eth 10G Eth 1/5.2 subinterfaces
switch#
 

 
Related Commands

Command
Description

interface ethernet

Configures an Ethernet IEEE 802.3 interface.

interface ethernet (Layer 3)

Configures a Layer 3 Ethernet IEEE 802.3 interface.

switchport mode vntag

Configures an Ethernet interface as a VNTag port.

switchport monitor rate-limit

Configures the rate limit for traffic on an interface.

show interface loopback

To display information about the loopback interface, use the show interface loopback command.

show interface loopback lo-number [ brief | description ]

 
Syntax Description

lo-number

Loopback interface number. The range is from 0 to 1023.

brief

(Optional) Displays a brief summary of the loopback interface information.

description

(Optional) Displays the description provided for the loopback interface.

 
Command Default

None

 
Command Modes

EXEC mode

 
Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display the configuration information for a specific loopback interface:

switch# show interface loopback 10
loopback10 is up
Hardware: Loopback
MTU 1500 bytes, BW 8000000 Kbit, DLY 5000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation LOOPBACK
0 packets input 0 bytes
0 multicast frames 0 compressed
0 input errors 0 frame 0 overrun 0 fifo
0 packets output 0 bytes 0 underruns
0 output errors 0 collisions 0 fifo
 
switch#
 

Table 1 describes the significant fields shown in the display.

 

Table 1 show interface loopback Field Description

Field
Description

Loopback is...

Whether the interface hardware is currently active (whether carrier detect is present), is currently inactive (down), or has been taken down by an administrator (administratively down).

Hardware

Hardware is Loopback.

MTU

Maximum transmission unit (MTU) of the interface.

BW

Bandwidth (BW) of the interface in kilobits per second.

DLY

Delay (DLY) of the interface in microseconds.

reliability

Reliability of the interface as a fraction of 255 (255/255 is 100 percent reliability), calculated as an exponential average over 5 minutes.

txload

Load on the interface for transmitting packets as a fraction of 255 (255/255 is completely saturated), calculated as an exponential average over 5 minutes.

rxload

Load on the interface for receiving packets as a fraction of 255 (255/255 is completely saturated), calculated as an exponential average over 5 minutes.

Encapsulation

Encapsulation method assigned to an interface.

LOOPBACK

Whether loopback is set.

packets input

Total number of error-free packets received by the system.

bytes

Total number of bytes, including data and MAC encapsulation, in the error-free packets received by the system.

multicast frames

Total number of multicast frames enabled on the interface.

compressed

Total number of multicast frames compressed on the interface.

input errors

Sum of all errors that prevented the receipt of datagrams on the interface being examined. This number might not balance with the sum of the enumerated output errors, because some datagrams might have more than one error and others might have errors that do not fall into any of the specifically tabulated categories.

frame

Number of packets received incorrectly that have a CRC error and a noninteger number of octets. On a serial line, the problem usually the result of noise or other transmission problems.

overrun

Number of times the serial receiver hardware was unable to hand received data to a hardware buffer because the input rate exceeded the receiver’s ability to handle the data.

fifo

Number of First In, First Out (FIFO) errors in the receive direction.

packets output

Total number of messages transmitted by the system.

bytes

Total number of bytes, including data and MAC encapsulation, transmitted by the system.

underruns

Number of times that the far-end transmitter has been running faster than the near-end router’s receiver can handle. This condition might never happen (be reported) on some interfaces.

output errors

Sum of all errors that prevented the final transmission of datagrams out of the interface being examined. Note that this might not balance with the sum of the enumerated output errors, because some datagrams might have more than one error, and others might have errors that do not fall into any of the specifically tabulated categories.

collisions

Loopback interface does not have collisions.

fifo

Number of First In, First Out (FIFO) errors in the transmit direction.

This example shows how to display the brief information for a specific loopback interface:

switch# show interface loopback 10 brief
 
--------------------------------------------------------------------------------
Interface Status Description
--------------------------------------------------------------------------------
loopback10 up --
switch#
 

 
Related Commands

Command
Description

interface loopback

Configures a loopback interface.

 

show interface port-channel

To display the information about an EtherChannel interface configuration, use the show interface port-channel command.

show interface port-channel number [ . subinterface-number ] [ brief | counters | description | status ]

 
Syntax Description

number

EtherChannel number. The range is from 1 to 4096.

. subinterface-number

(Optional) Port-channel subinterface configuration. Use the EtherChannel number followed by a dot (.) indicator and the subinterface number. The format is as follows:

portchannel-number . subinterface-number

brief

(Optional) Displays information about the interface.

counters

(Optional) Displays information about the counters configured on the EtherChannel interface.

description

(Optional) Displays the description of the EtherChannel interface configuration.

status

(Optional) Displays the operational state of the EtherChannel interface.

 
Command Default

None

 
Command Modes

EXEC mode

 
Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display the configuration information of a specified EtherChannel interface:

switch# show interface port-channel 21
port-channel21 is up
Hardware: Port-Channel, address: 000d.ece7.df72 (bia 000d.ece7.df72)
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 10 Gb/s
Beacon is turned off
Input flow-control is on, output flow-control is on
Switchport monitor is off
Members in this channel: Eth2/3
Last clearing of "show interface" counters never
30 seconds input rate 0 bits/sec, 0 packets/sec
30 seconds output rate 352 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
input rate 0 bps, 0 pps; output rate 368 bps, 0 pps
RX
0 unicast packets 0 multicast packets 0 broadcast packets
0 input packets 0 bytes
0 jumbo packets 0 storm suppression packets
0 runts 0 giants 0 CRC 0 no buffer
0 input error 0 short frame 0 overrun 0 underrun 0 ignored
0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
0 input with dribble 0 input discard
0 Rx pause
TX
0 unicast packets 15813 multicast packets 9 broadcast packets
15822 output packets 1615917 bytes
0 jumbo packets
0 output errors 0 collision 0 deferred 0 late collision
0 lost carrier 0 no carrier 0 babble
0 Tx pause
1 interface resets
 
switch#
 

 
Related Commands

Command
Description

interface port-channel

Configures an EtherChannel interface.

 

show ip arp

To display the Address Resolution Protocol (ARP) information, use the show ip arp command.

show ip arp [ ip-addr | { ethernet slot / port | loopback if_number | mgmt mif_number | port-channel number } ] [ client ] [ static ] [ statistics ] [ vrf vrf-name ]

 
Syntax Description

ip-addr

(Optional) IPv4 source address. The format is x.x.x.x.

ethernet slot / port

(Optional) Specifies the Ethernet interface. The slot number is from 1 to 255, and the port number is from 1 to 128.

loopback if_number

(Optional) Specifies the loopback interface. The loopback interface number is from 0 to 1023.

mgmt mif_number

(Optional) Specifies the management interface. The management interface number is from 0 to 1023.

port-channel number

(Optional) Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.

client

(Optional) Displays the ARP client table

static

(Optional) Displays static ARP entries.

statistics

(Optional) Displays ARP statistics.

vrf vrf-name

(Optional) Specifies the virtual router context (VRF) name. The name can be any case-sensitive, alphanumeric string up to 32 characters.

 
Command Default

None

 
Command Modes

Any command mode

 
Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display the ARP information:

switch# show ip arp
 
Flags: D - Static Adjacencies attached to down interface
 
IP ARP Table for context default
Total number of entries: 1
Address Age MAC Address Interface
2.2.2.100 - 000a.000a.000a Ethernet1/2
switch#
 

 
Related Commands

Command
Description

ip arp

Configures a static ARP entry.

show ip arp summary

To display Address Resolution Protocol (ARP) adjacency summary, use the show ip arp summary command.

show ip arp summary

 
Syntax Description

This command has no arguments or keywords.

 
Command Default

None

 
Command Modes

Global configuration mode

 
Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display an ARP adjacency summary:

switch# show ip arp summary
 
IP ARP Table - Adjacency Summary
 
Resolved : 0
Incomplete : 0
Unknown : 0
Total : 0
 
switch#
 

 
Related Commands

Command
Description

ip arp timeout

Configures ARP.

 

show ip client

To display information about the internal IP clients, use the show ip client command.

show ip client [ name ]

 
Syntax Description

name

(Optional) Name of the client.

 
Command Default

None

 
Command Modes

Any command mode

 
Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display the IP client information for the Address Resolution Protocol (ARP):

switch(config)# show ip client arp
 

 
Related Commands

Command
Description

show ip process

Displays information about the IP process.

 

show ip interface

To display IP information for an interface, use the show ip interface command.

show ip interface [ type number ] [ brief ] [ vrf vrf-name ]

 
Syntax Description

type

(Optional) Interface type. Use ? to see the options.

number

(Optional) Interface number. Use ? to see the range.

brief

(Optional) Displays a summary of IP information.

vrf vrf-name

(Optional) Specifies the name of the virtual routing and forwarding (VRF) instance. The vrf-name argument can be specified as any case-sensitive, alphanumeric string up to 32 characters. The strings “default” and “all” are reserved VRF names.

 
Command Default

None

 
Command Modes

Any command mode

 
Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display the IP information for Ethernet 1/5:

switch# show ip interface ethernet 1/5
IP Interface Status for VRF "default"(1)
Ethernet1/5, Interface status: protocol-down/link-down/admin-up, iod: 11,
IP address: 192.0.0.1, IP subnet: 192.0.0.0/24
IP broadcast address: 255.255.255.255
IP multicast groups locally joined: none
IP MTU: 1500 bytes (using link MTU)
IP primary address route-preference: 0, tag: 0
IP proxy ARP : disabled
IP Local Proxy ARP : disabled
IP multicast routing: disabled
IP icmp redirects: enabled
IP directed-broadcast: disabled
IP icmp unreachables (except port): disabled
IP icmp port-unreachable: enabled
IP unicast reverse path forwarding: none
IP load sharing: none
IP interface statistics last reset: never
IP interface software stats: (sent/received/forwarded/originated/consumed)
Unicast packets : 0/0/0/0/0
Unicast bytes : 0/0/0/0/0
Multicast packets : 0/0/0/0/0
Multicast bytes : 0/0/0/0/0
Broadcast packets : 0/0/0/0/0
Broadcast bytes : 0/0/0/0/0
Labeled packets : 0/0/0/0/0
Labeled bytes : 0/0/0/0/0
switch#
 

 
Related Commands

Command
Description

ip address

Assigns a primary IP address for a network interface.

show ip wccp

To display global statistics related to the Web Cache Communication Protocol (WCCP), use the show ip wccp command.

show ip wccp [ vrf vrf-id ] [ service-number | web-cache ] [ detail | view ]

 
Syntax Description

vrf vrf-id

(Optional) Displays the virtual routing and forwarding (VRF) instance. If no VRF is specified, the command refers to the default global VRF.

service-number

(Optional) Identification number of the service group that is controlled by the cache engine (CE). The valid range is from 0 to 254.

web-cache

(Optional) Displays the statistics for the web-cache service.

detail

(Optional) Displays the information about the router and all web caches.

view

(Optional) Displays the other members of a service group that have or have not been detected.

 
Command Modes

EXEC command mode

 
Command History

Release
Modification

7.0(0)N1(1)

This command was introduced.

Examples

This example shows how to display WCCP global statistics:

switch# show ip wccp 90

 

Global WCCP information:
Router information:
Router Identifier: 1.104.217.34
Protocol Version: 2.0
 
Service Identifier: 61
Number of Service Group Clients: 1
Number of Service Group Routers: 1
Service mode: Open
Service Access-list: -none-
Redirect Access-list: red1
Service Identifier: 62
Number of Service Group Clients: 1
Number of Service Group Routers: 1
Service mode: Open
Serivce Access-list: -none-
Redirect Access-list: red1
 

The following table entries describe the significant fields shown in the display:

 

Field
Description

Router information

List of routers detected by the current router.

Protocol version

Version of WCCP used by the router in the service group.

Service identifier

Service is detailed.

Number of service group clients

Number of clients visible to the router and other clients in the service group.

Number of service group routers

Number of routers in the service group.

Service mode:Closed

WCCP service mode. Options are open or closed.

Service access list

Named extended IP access list that defines the packets that will match the service.

Redirect access list

Name or number of the access list that determines which packets will be redirected.

This example shows how to display the other members of a service group:

switch# show ip wccp 10 view
 
WCCP Router Informed of:
10.168.88.10
10.168.88.20
 
WCCP Cache Engines Visible
10.168.88.11
10.168.88.12
 
WCCP Cache Engines Not Visible:
-none-
 

Note The maximum number of service groups that can be configured is 256.


If any cache engine is displayed under the WCCP Cache Engines Not Visible field, the router needs to be reconfigured to map the cache engine that is not visible to it.

The following table describes the significant fields shown in the display.

 

Field
Description

WCCP Router Informed of

List of routers detected by the current router.

WCCP Clients Visible

List of clients that is visible to the router and other clients in the service group.

WCCP Clients Not Visible

List of clients in the service group that is not visible to the router and other clients in the service group.

This example show how to display WCCP client information and WCCP router statistics that include the type of services:

switch# show ip wccp 91 detail
 
WCCP Client information:
WCCP Client ID: 70.1.1.1
Protocol Version: 2.0
State: Usable
Redirection: L2
Packet Return: L2
Connect Time: 25:32:16
Assignment: MASK
Mask SrcAddr DstAddr SrcPort DstPort
0001: 0x00000001 0x00000000 0x0000 0x0000
Value SrcAddr DstAddr SrcPort DstPort CE-IP
----- ------- ------- ------- ------- -----
0001: 0x00000000 0x00000000 0x0000 0x0000 0x46010101 (70.1.1.1)
0002: 0x00000001 0x00000000 0x0000 0x0000 0x46010101 (70.1.1.1)
 

 
Related Commands

Command
Description

ip wccp

Enables WCCP on a router and specifies the type of services to be used.

ip wccp redirect

Enables packet redirection on an outbound or inbound interface using WCCP.

show ip interface

Lists a summary of the IP information and status of an interface.

show running-config arp

To display the Address Resolution Protocol (ARP) configuration in the running configuration, use the show running-config arp command.

show running-config arp [ all ]

 
Syntax Description

all

(Optional) Displays configured and default information.

 
Command Default

None

 
Command Modes

Any command mode

 
Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display the ARP configuration:

switch# show running-config arp
 
!Command: show running-config arp
!Time: Mon Aug 23 07:33:15 2010
 
version 5.0(2)N1(1)
ip arp timeout 2100
ip arp event-history errors size medium
 
interface Vlan10
ip arp 192.0.11.37 00C0.4F00.0000
 
switch#
 

This example shows how to display the ARP configuration with the default information:

switch# show running-config arp all
 
!Command: show running-config arp all
!Time: Mon Aug 23 07:33:52 2010
 
version 5.0(2)N1(1)
ip arp timeout 1500
ip arp event-history cli size small
ip arp event-history snmp size small
ip arp event-history client-errors size small
ip arp event-history client-event size small
ip arp event-history lcache-errors size small
ip arp event-history lcache size small
ip arp event-history errors size small
ip arp event-history ha size small
ip arp event-history event size small
ip arp event-history packet size small
 
interface Vlan10
ip arp 192.0.11.37 00C0.4F00.0000
ip arp gratuitous update
ip arp gratuitous request
 
switch#
 

 
Related Commands

Command
Description

copy running-config startup-config

Copies the running configuration to the startup configuration file.

ip arp timeout

Configures an ARP timeout.

show startup-config arp

Displays the ARP startup configuration.

show running-config arp

To display the Address Resolution Protocol (ARP) configuration in the running configuration, use the show running-config arp command.

show running-config arp [ all ]

 
Syntax Description

all

(Optional) Displays configured and default information.

 
Command Default

None

 
Command Modes

Any command mode

 
Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display the ARP configuration:

switch# show running-config arp
 
!Command: show running-config arp
!Time: Mon Aug 23 07:33:15 2010
 
version 5.0(2)N1(1)
ip arp timeout 2100
ip arp event-history errors size medium
 
interface Vlan10
ip arp 192.0.11.37 00C0.4F00.0000
 
switch#
 

This example shows how to display the ARP configuration with the default information:

switch# show running-config arp all
 
!Command: show running-config arp all
!Time: Mon Aug 23 07:33:52 2010
 
version 5.0(2)N1(1)
ip arp timeout 1500
ip arp event-history cli size small
ip arp event-history snmp size small
ip arp event-history client-errors size small
ip arp event-history client-event size small
ip arp event-history lcache-errors size small
ip arp event-history lcache size small
ip arp event-history errors size small
ip arp event-history ha size small
ip arp event-history event size small
ip arp event-history packet size small
 
interface Vlan10
ip arp 192.0.11.37 00C0.4F00.0000
ip arp gratuitous update
ip arp gratuitous request
 
switch#
 

 
Related Commands

Command
Description

copy running-config startup-config

Copies the running configuration to the startup configuration file.

ip arp timeout

Configures an ARP timeout.

show startup-config arp

Displays the ARP startup configuration.

show startup-config arp

To display the Address Resolution Protocol (ARP) configuration in the startup configuration, use the show startup-config arp command.

show startup-config arp [ all ]

 
Syntax Description

all

(Optional) Displays configured and default information.

 
Command Default

None

 
Command Modes

Any command mode

 
Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.

Examples

This example shows how to display the ARP startup configuration:

switch# show startup-config arp
 
!Command: show running-config arp
!Time: Mon Aug 23 07:33:15 2010
 
version 5.0(2)N1(1)
ip arp timeout 2100
ip arp event-history errors size medium
 
interface Vlan10
ip arp 192.0.1.37 00C0.4F00.0000
 
switch#
 

 
Related Commands

Command
Description

copy running-config startup-config

Copies the running configuration to the startup configuration file.

ip arp timeout

Configures an ARP timeout.

show running-config arp

Displays the ARP running configuration.