The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
To display information about Multicast Source Discovery Protocol (MSDP) counts, use the show ip msdp count command.
show ip msdp count [ asn ] [ vrf { vrf-name | all }]
(Optional) Applies to a virtual routing and forwarding (VRF) instance. |
|
VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive. |
|
network-admin
network-operator
vdc-admin
vdc-operator
|
|
This example shows how to display MSDP counts:
switch(
config)#
show ip msdp count
To display information in the Multicast Source Discovery Protocol (MSDP) event history buffers, use the show ip msdp event-history command.
show ip msdp event-history { errors | msgs | statistics }
network-admin
network-operator
vdc-admin
vdc-operator
|
|
This example shows how to display information in the MSDP msgs event history buffer:
switch(config)#
show ip msdp event-history msgs
|
|
---|---|
To display information about Multicast Source Discovery Protocol (MSDP) mesh groups, use the show ip msdp mesh-group command.
show ip msdp mesh-group [ mesh-group ] [ vrf { vrf-name | all }]
(Optional) Applies to a virtual routing and forwarding (VRF) instance. |
|
VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive. |
|
network-admin
network-operator
vdc-admin
vdc-operator
|
|
This example shows how to display information about MSDP mesh groups:
switch(
config)#
show ip msdp mesh-group
To display information about Multicast Source Discovery Protocol (MSDP) peers, use the show ip msdp peer command.
show ip msdp peer [ peer-address ] [ vrf { vrf-name | all }]
(Optional) Applies to a virtual routing and forwarding (VRF) instance. |
|
VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive. |
|
network-admin
network-operator
vdc-admin
vdc-operator
|
|
This example shows how to display information about MSDP peers:
switch(
config)#
show ip msdp peer
To display information about Multicast Source Discovery Protocol (MSDP) Source-Active (SA) policies, use the show ip msdp policy statistics sa-policy command.
show ip msdp policy statistics sa-policy peer-address { in | out } [ vrf { vrf-name }]
(Optional) Applies to a virtual routing and forwarding (VRF) instance. |
|
VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive. |
network-admin
network-operator
vdc-admin
vdc-operator
|
|
This example shows how to display information about MSDP SA policies:
switch(
config)#
show ip msdp policy statistics sa-policy 192.168.1.10 in
To display information about the Multicast Source Discovery Protocol (MSDP) Source-Active (SA) cache, use the show ip msdp route command.
show ip msdp route [{ source [ group ]} | { group [ source ]}] [ asn ] [ peer peer ] [ detail ] [ vrf { vrf-name | all }]
(Optional) Applies to a virtual routing and forwarding (VRF) instance. |
|
VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive. |
|
network-admin
network-operator
vdc-admin
vdc-operator
|
|
The show ip msdp sa-cache command is an alternative form of this command.
This example shows how to display information about the MSDP SA cache:
switch(
config)#
show ip msdp route
|
|
---|---|
To display information about the Multicast Source Discovery Protocol (MSDP) next-hop autonomous system (AS) on the Border Gateway Protocol (BGP) path to a rendezvous point (RP) address, use the show ip msdp rpf command.
show ip msdp rpf rp-address [ vrf { vrf-name all }]
(Optional) Applies to a virtual routing and forwarding (VRF) instance. |
|
VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive. |
|
network-admin
network-operator
vdc-admin
vdc-operator
|
|
This example shows how to display information about MSDP reverse path forwarding (RPF) peers:
switch(
config)#
show ip msdp rpf 192.168.1.10
To display information about the Multicast Source Discovery Protocol (MSDP) Source-Active (SA) cache, use the show ip msdp sa-cache command.
show ip msdp sa-cache [{ source [ group ]} | { group [ source ]}] [ asn ] [ peer peer ] [ detail ] [ vrf { vrf-name | all }]
(Optional) Applies to a virtual routing and forwarding (VRF) instance. |
|
VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive. |
|
network-admin
network-operator
vdc-admin
vdc-operator
|
|
The show ip msdp route command is an alternative form of this command.
This example shows how to display information about the MSDP SA cache:
switch(
config)#
show ip msdp sa-cache
|
|
---|---|
To display information about the Multicast Source Discovery Protocol (MSDP) Source-Active (SA) route cache, use the show ip msdp route command.
show ip msdp route [{ source [ group ]} | { group [ source ]}] [ asn ] [ peer peer ] [ detail ] [ vrf { vrf-name | all }]
(Optional) Applies to a virtual routing and forwarding (VRF) instance. |
|
VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive. |
|
network-admin
network-operator
vdc-admin
vdc-operator
|
|
The show ip msdp route command is an alternative form of this command.
This example shows how to display information about the MSDP SA cache:
switch(
config)#
show ip msdp sa-cache
|
|
---|---|
To display information about Multicast Source Discovery Protocol (MSDP) learned sources, use the show ip msdp sources command.
show ip msdp sources [ vrf { vrf-name | all }]
(Optional) Applies to a virtual routing and forwarding (VRF) instance. |
|
VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive. |
|
network-admin
network-operator
vdc-admin
vdc-operator
|
|
This example shows how to display information about MSDP learned sources:
switch(
config)#
show ip msdp sources
To display summary information about Multicast Source Discovery Protocol (MSDP) peers, use the show ip msdp summary command.
show ip msdp summary [ vrf { vrf-name | all }]
(Optional) Applies to a virtual routing and forwarding (VRF) instance. |
|
VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive. |
|
network-admin
network-operator
vdc-admin
vdc-operator
|
|
This example shows how to display summary information about MSDP peers:
switch(
config)#
show ip msdp summary
To display information about the running-system configuration for Multicast Source Discovery Protocol (MSDP), use the show running-config msdp command.
show running-config msdp [ all ]
network-admin
network-operator
vdc-admin
vdc-operator
|
|
This example shows how to display information about the MSDP running-system configuration:
switch(
config)#
show running-config msdp
To display information about the startup-system configuration for Multicast Source Discovery Protocol (MSDP), use the show startup-config msdp command.
show startup-config msdp [ all ]
network-admin
network-operator
vdc-admin
vdc-operator
|
|
This example shows how to display information about the startup-system configuration for MSDP:
switch(
config)#
show startup-config msdp