The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
Contents
A - B - C - D - E - I - L - M - P - R - S - T - U - V
Index
A
adding portsport channels 1B
bandwidthconfiguring 1C
channel modeport channels 1channel modesport channels 1configurationLayer 3 interfacesverifying 1configuration examplesLayer 3 interfaces 1configuringdescription parameter 1error-disabled recovery interval 1interface bandwidth 1LACP fast timer rate 1LACP port priority 1loopback interfaces 1routed interfaces 1subinterfaces 1VLAN interfaces 1Configuring a DHCP client on an interface 1configuring LACP 1D
debounce timerparameters 1debounce timer, configuringEthernet interfaces 1default interface 1default settingsLayer 3 interfaces 1delay restore 1disablingCDP 1error-disabled recovery 1ethernet interfaces 1link negotiation 1vPCs 1downlink delay 1E
enablingCDP 1error-disabled detection 1error-disabled recovery 1Ethernet interfacesdebounce timer, configuring 1interface speed 1I
interface ethernet 1interface information, displayinglayer 2 1interface MAC address, configuring 1interface speedconfiguring 1Ethernet interfaces 1interfacesassigning to a VRF 1chassis ID 1configuring bandwidth 1Layer 3 1configuration examples 1monitoring 1options 1routed 1tunnel 1UDLD 1VLAN 1configuring 1interfaces-vlan 1L
LACP 1configuring 1marker responders 1port channels 1system ID 1LACP fast timer rateconfiguring 1lacp graceful-convergence 1lacp max-bundle 1LACP port priorityconfiguring 1LACP-enabled vs staticport channels 1layer 2interface information, displaying 1svi autostate 1svi autostate, disabling 1Layer 3 interfaces 1configuration examples 1configuring routed interfaces 1default settings 1interfacesLayer 3monitoring 1related documents 1verifying 1Link Aggregation Control Protocol 1load balancingport channelsconfiguring 1loopback interfaces 1configuring 1M
monitoringLayer 3 interfaces 1P
parameters, aboutdebounce timer 1physical Ethernet settings 1port channelverifying configuration 1port channel, minlinksport channeling 1port channelsadding ports 1channel mode 1compatibility requirements 1configuring bandwidth 1creating 1LACP 1LACP-enabled vs static 1port channels 1moving into a vPC 1STP 1R
related documentsLayer 3 interfaces 1restartingethernet interfaces 1routed interfaces 1configuring 1configuring bandwidth 1S
SFP+ transceiver 1show running-config interface port-channel 1Small form-factor pluggable (plus) transceiver 1STPport channel 1subinterfaces 1configuring 1configuring bandwidth 1svi autostatelayer 2 1SVI autostate disable 1SVI autostate disable, configuring 1svi autostate, disablinglayer 2 1switchport 1switchport dot1q ethertype 1switchport mode 1symmetric hashing 1T
tunnel interfaces 1U
UDLDaggressive mode 1defined 1nonaggressive mode 1UDLD modeAconfiguring 1Unidirectional Link Detection 1V
verifyingLayer 3 interface configuration 1VLANinterfaces 1VLAN interfacesconfiguring 1vPC terminology 1vPCsmoving port channels into 1VRFassigning an interface to 1