- show aaa accounting
- show aaa authentication
- show aaa groups
- show access-list summary
- show accounting log
- show banner motd
- show boot
- show cdp
- show cdp neighbors
- show class-map
- show cli variables
- show cores
- show file
- show flow exporter
- show flow interface
- show flow monitor
- show flow record
- show interface brief
- show interface capabilities
- show interface counters trunk
- show interface ethernet
- show interface ethernet counters
- show interface ethernet status
- show interface ethernet transceiver
- show interface port-channel
- show interface port-channel counters
- show interface status
- show interface switchport
- show interface trunk
- show interface vethernet
- show interface vethernet counters
- show interface vethernet status
- show interface virtual
- show interface virtual port-mapping
- show ip access-list
- show ip access-list summary
- show ip arp client
- show ip arp inspection interface
- show ip arp inspection statistics
- show ip arp inspection vlan
- show ip arp statistics
- show ip dhcp snooping
- show ip dhcp snooping binding
- show ip dhcp snooping statistics
- show ip igmp snooping
- show ip igmp snooping explicit-tracking vlan
- show ip igmp snooping groups
- show ip igmp snooping mrouter
- show ip igmp snooping querier
- show ip verify source
- show lacp counters
- show lacp interface
- show lacp neighbor
- show lacp port-channel
- show lacp system-identifier
- show license
- show license brief
- show license file
- show license host-id
- show license usage
- show logging logfile
- show logging module
- show logging server
- show logging timestamp
- show mac access-lists
- show mac address-table
- show mac address-table aging-time
- show module
- show module vem mapping
- show monitor
- show monitor session
- show ntp peer-status
- show ntp peers
- show ntp statistics
- show password strength-check
- show policy-map
- show policy-map interface
- show port-channel compatibility-parameters
- show port-channel database
- show port-channel load-balance
- show port-channel rbh-distribution
- show port-channel summary
- show port-channel traffic
- show port-channel usage
- show port-profile
- show port-profile expand-interface
- show port-security
- show port-security address
- show port-security interface
- show processes
- show radius-server
- show radius-server directed-request
- show radius-server groups
- show radius-server sorted
- show radius-server statistics
- show running-config diff
- show running-config interface ethernet
- show running-config interface port-channel
- show running-config port-profile
- show running-config interface vethernet
- show running-config vlan
- show radius-server directed-request
- show snmp
- show ssh key
- show ssh server
- show startup-config aaa
- show startup-config radius
- show startup-config security
- show svs connections
- show svs domain
- show svs neighbors
- show system error-id
- show system redundancy status
- show system resources
- show system vem feature level
- show tacacs-server
- show tcp client
- show tcp connection
- show tcp statistics
- show tech-support
- show telnet server
- show terminal
- show user-account
- show users
- show version
- show version image
- show virtual-service-domain brief
- show virtual-service-domain interface
- show virtual-service-domain name
- show vlan
- show vlan all-ports
- show vlan brief
- show vlan id
- show vlan private-vlan
- show vlan summary
- show vmware vc extension-key
- show vmware vem upgrade status
- show xml server status
Show Commands
This chapter describes the Cisco Nexus 1000V show commands.
Note 
This chapter is a work in progress and does not yet include all show commands.
show aaa accounting
To display the AAA accounting configuration, use the show aaa accounting command.
show aaa accounting
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the accounting configuration:
n1000v# show aaa accounting
default: local
n1000v#
Related Commands
show aaa authentication
To display the configuration for AAA authentication, use the show aaa authentication command.
show aaa authentication [login error-enable | login mschap]
Syntax Description
login error-enable |
(Optional) Displays the authentication login error message enable configuration. |
login mschap |
(Optional) Displays the authentication login MS-CHAP enable configuration. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the configured authentication parameters:
n1000v# show aaa authentication
default: local
console: local
This example shows how to display the authentication-login error-enable configuration:
n1000v# show aaa authentication login error-enable
disabled
This example shows how to display the authentication-login MSCHAP configuration:
n1000v# show aaa authentication login mschap
disabled
Related Commands
show aaa groups
To display the configured AAA server groups, use the show aaa groups command.
show aaa groups
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display AAA group information:
n1000v# show aaa groups
radius
TacServer
Related Commands
|
|
|
|---|---|
aaa group |
Configures an AAA server group. |
show running-config aaa [all] |
Displays the AAA configuration as it currently exists in the running configuration. |
show access-list summary
To display configured access control lists (ACLs), use the show access-list summary command.
show access-list summary
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display configured ACLs:
n1000v# show access-lists summary
IP access list acl1
Total ACEs Configured:1
n1000v#n1000v#
Related Commands
|
|
|
|---|---|
ip access-list |
Creates the IP ACL and enters IP ACL configuration mode. |
show ip access-lists |
Displays the IP ACL configuration. |
show accounting log
To display the accounting log contents, use the show accounting log command.
show accounting log [size] [start-time year month day HH:MM:SS]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the entire accounting log:
n1000v# show accounting log
Wed Jul 22 02:09:44 2009:update:vsh.3286:root:configure terminal ; port-profile Unused_O
r_Quarantine_Uplink ; capability uplink (SUCCESS)
Wed Jul 22 07:57:50 2009:update:171.71.55.185@pts/2:admin:configure terminal ; flow reco
rd newflowrecord (SUCCESS)
Wed Jul 22 08:48:57 2009:start:swordfish-build1.cisco.com@pts:admin:
Wed Jul 22 08:49:03 2009:stop:swordfish-build1.cisco.com@pts:admin:shell terminated grac
efully
Wed Jul 22 08:50:36 2009:update:171.71.55.185@pts/2:admin:configure terminal ; no flow r
ecord newflowrecord (SUCCESS)
Thu Jul 23 07:21:50 2009:update:vsh.29016:root:configure terminal ; port-profile Unused_
Or_Quarantine_Veth ; state enabled (SUCCESS)
Thu Jul 23 10:25:19 2009:start:171.71.55.185@pts/5:admin:
Thu Jul 23 11:07:37 2009:update:171.71.55.185@pts/5:admin:enabled aaa user default role
enabled/disabled
doc-n1000v(config)#
This example shows how to display 400 bytes of the accounting log:
n1000v# show accounting log 400
Sat Feb 16 21:15:24 2008:update:/dev/pts/1_172.28.254.254:admin:show accounting log start-time 2008 Feb 16 18:31:21
Sat Feb 16 21:15:25 2008:update:/dev/pts/1_172.28.254.254:admin:show system uptime
Sat Feb 16 21:15:26 2008:update:/dev/pts/1_172.28.254.254:admin:show clock
This example shows how to display the accounting log starting at 16:00:00 on February 16, 2008:
n1000v(config)# show accounting log start-time 2008 Feb 16 16:00:00
Sat Feb 16 16:00:18 2008:update:/dev/pts/1_172.28.254.254:admin:show logging log file start-time 2008 Feb 16 15:59:16
Sat Feb 16 16:00:26 2008:update:/dev/pts/1_172.28.254.254:admin:show accounting log start-time 2008 Feb 16 12:05:16
Sat Feb 16 16:00:27 2008:update:/dev/pts/1_172.28.254.254:admin:show system uptime
Sat Feb 16 16:00:28 2008:update:/dev/pts/1_172.28.254.254:admin:show clock
Sat Feb 16 16:01:18 2008:update:/dev/pts/1_172.28.254.254:admin:show logging log file start-time 2008 Feb 16 16:00:16
Sat Feb 16 16:01:26 2008:update:/dev/pts/1_172.28.254.254:admin:show accounting log start-time 2008 Feb 16 12:05:16
Sat Feb 16 16:01:27 2008:update:/dev/pts/1_172.28.254.254:admin:show system uptime
Sat Feb 16 16:01:29 2008:update:/dev/pts/1_172.28.254.254:admin:show clock
Sat Feb 16 16:02:18 2008:update:/dev/pts/1_172.28.254.254:admin:show logging log file start-time 2008 Feb 16 16:01:16
Sat Feb 16 16:02:26 2008:update:/dev/pts/1_172.28.254.254:admin:show accounting log start-time 2008 Feb 16 12:05:16
Sat Feb 16 16:02:28 2008:update:/dev/pts/1_172.28.254.254:admin:show system uptime
Related Commands
|
|
|
|---|---|
clear accounting log |
Clears the accounting log. |
show banner motd
To display the configured banner message, use the show banner motd command.
show banner motd
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the configured banner message:
n1000v(config)# show banner motd
April 16, 2008 Welcome to the Switch
Related Commands
|
|
|
|---|---|
banner motd |
Configures the banner message of the day. |
switchname |
Changes the switch prompt. |
show boot
To display the system and kickstart boot variables for verification, use the show boot command.
show boot [auto-copy [list] | sup-1 | sup-2 | variables]
Syntax Description
Defaults
None
Command Modes
Global configuration (config)
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the system and kickstart boot variables for verification:
n1000v# config t
n1000v(config)# show boot
sup-1
kickstart variable =
bootflash:/nexus-1000v-kickstart-mzg.4.0.4
.SV1.2.bin
system variable =
bootflash:/nexus-1000v-mzg.4.0.4.SV1.2.bin
sup-2
kickstart variable =
bootflash:/nexus-1000v-kickstart-mzg.4.0.4
.SV1.2.bin
system variable =
bootflash:/nexus-1000v-mzg.4.0.4.SV1.2.bin
No module boot variable set
n1000v(config)#
Related Commands
show cdp
To display your Cisco Discovery Protocol (CDP) configuration, use the show cdp command.
show cdp {all | entry {all | name s0} | global | interface if0 | traffic interface if2}
Syntax Description
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the global CDP configuration:
n1000v(config)# show cdp global
Global CDP information:
CDP enabled globally
Sending CDP packets every 5 seconds
Sending a holdtime value of 10 seconds
Sending CDPv2 advertisements is disabled
Sending DeviceID TLV in Mac Address Format
This example shows how to display the CDP configuration for a specified interface:
n1000v(config)# show cdp interface ethernet 2/3
Ethernet2/3 is up
CDP enabled on interface
Sending CDP packets every 60 seconds
Holdtime is 180 seconds
This example shows how to display the CDP traffic statistics for a specified interface:
n1000v(config)# show cdp traffic interface ethernet 2/3
----------------------------------------
Traffic statistics for Ethernet2/3
Input Statistics:
Total Packets: 98
Valid CDP Packets: 49
CDP v1 Packets: 49
CDP v2 Packets: 0
Invalid CDP Packets: 49
Unsupported Version: 49
Checksum Errors: 0
Malformed Packets: 0
Output Statistics:
Total Packets: 47
CDP v1 Packets: 47
CDP v2 Packets: 0
Send Errors: 0
This example shows how to display CDP parameters for all interfaces:
n1000v# show cdp all
Ethernet2/2 is up
CDP enabled on interface
Sending CDP packets every 60 seconds
Holdtime is 180 seconds
Ethernet2/3 is up
CDP enabled on interface
Sending CDP packets every 60 seconds
Holdtime is 180 seconds
Ethernet2/4 is up
CDP enabled on interface
Sending CDP packets every 60 seconds
Holdtime is 180 seconds
Ethernet2/5 is up
CDP enabled on interface
Sending CDP packets every 60 seconds
Holdtime is 180 seconds
Ethernet2/6 is up
CDP enabled on interface
Sending CDP packets every 60 seconds
Holdtime is 180 seconds
mgmt0 is up
CDP enabled on interface
Sending CDP packets every 60 seconds
Holdtime is 180 seconds
Related Commands
show cdp neighbors
To display the configuration and capabilities of upstream devices, use the show cdp neighbors command.
show cdp neighbors [interface if] detail
Syntax Description
interface if |
(Optional) Show CDP neighbors for a specified interface. |
detail |
Show the detailed configuration of all CDP neighbors. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the configuration and capabilities of upstream devices:
n1000v(config)# show cdp neighbors
Capability Codes: R - Router, T - Trans-Bridge, B - Source-Route-Bridge
S - Switch, H - Host, I - IGMP, r - Repeater,
V - VoIP-Phone, D - Remotely-Managed-Device,
s - Supports-STP-Dispute
Device ID Local Intrfce Hldtme Capability Platform Port ID
swordfish-6k-2 Eth2/2 169 R S I WS-C6503-E Gig1/14
swordfish-6k-2 Eth2/3 139 R S I WS-C6503-E Gig1/15
swordfish-6k-2 Eth2/4 135 R S I WS-C6503-E Gig1/16
swordfish-6k-2 Eth2/5 177 R S I WS-C6503-E Gig1/17
swordfish-6k-2 Eth2/6 141 R S I WS-C6503-E Gig1/18
This example shows how to display configuration and capabilities of upstream devices for a specific interface:
n1000v(config)# show cdp neighbors interface ethernet 2/3
Capability Codes: R - Router, T - Trans-Bridge, B - Source-Route-Bridge
S - Switch, H - Host, I - IGMP, r - Repeater,
V - VoIP-Phone, D - Remotely-Managed-Device,
s - Supports-STP-Dispute
Device ID Local Intrfce Hldtme Capability Platform Port ID
swordfish-6k-2 Eth2/3 173 R S I WS-C6503-E Gig1/15
Related Commands
show class-map
To display the class map configuration for all class maps or for a specified class map, use the show class-map command.
show class-map [[type qos] [cmap-name]]
Syntax Description
type |
(Optional) Specifies the type of the class map. |
qos |
(Optional) Specifies the type QoS. |
cmap-name |
(Optional) Name of an existing class map. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the class map configuration for all class maps with the type qos:
n1000v# show class-map type qos
Type qos class-maps
====================
class-map type qos match-all class1
class-map type qos match-all class2
n1000v#
Related Commands
show cli variables
To display user-defined CLI persistent variables, use the show cli variables command.
To remove user-defined CLI persistent variables, use the cli no var name command in configuration mode.
show cli variables
cli no var name name
Syntax Description
name |
Name of an existing variable. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display user-defined CLI persistent variables:
n1000v# show cli variables
VSH Variable List
-----------------
TIMESTAMP="2008-07-02-13.45.15"
testinterface="ethernet 3/1"
This example shows how to remove the user-defined CLI persistent variable, mgmtport.
n1000v# cli no var name mgmtport
n1000v#
Related Commands
|
|
|
|---|---|
cli var name |
Defines a command-line interface (CLI) variable for a terminal session. |
run-script |
Runs a command script that is saved in a file. |
show cores
To view recent core images, use the show cores command.
show cores
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
System core image files are generated when a service fails.
Examples
This example shows how to display recent core images:
n1000v# show cores
Module-num Instance-num Process-name PID Core-create-time
---------- ------------ ------------ --- ----------------
n1000v#
Related Commands
|
|
|
|---|---|
show processes |
Displays information regarding process logs. |
show file
To display a full filename by entering a partial filename and pressing the Tab key, use the show file command.
show file {bootflash: | volatile: | debug:} partial_filename [cksum | md5sum]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
When you type a partial filename and then press Tab, the CLI completes the filename if the characters that you typed are unique to a single file.
If not, the CLI lists a selection of filenames that match the characters that you typed.
You can then retype enough characters to make the filename unique; and CLI completes the filename for you.
Examples
This example shows how to display a full filename by entering a partial filename and pressing the Tab key:
n1000v# show file bootflash:nexus-1000v <Tab>
bootflash:nexus-1000v-dplug-mzg.4.0.4.SV1.0.42.bin bootflash:nexus-1000v-mzg.4.0.4.SV1.0.42.bin
bootflash:nexus-1000v-kickstart-mzg.4.0.4.SV1.0.42.bin
Related Commands
show flow exporter
To display information about the flow exporter, use the show flow exporter command.
show flow exporter [name]
Syntax Description
name |
(Optional) Name of an existing flow exporter. |
Defaults
None
Command Modes
CLI flow exporter configuration (config-flow-exporter)
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display information about the flow exporter:
n1000v(config-flow-exporter)# show flow exporter
Related Commands
show flow interface
To display the NetFlow configuration for the specified interface, use the show flow interface command.
show flow interface {ethernet interface_number | vethernet slot_number}
Syntax Description
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display NetFlow configuration information for vEthernet slot 2:
n1000v(config-if)# show flow interface veth 2
Interface veth 2:
Monitor: MonitorTest
Direction: Output
Related Commands
show flow monitor
To display information about existing flow monitors, use the show flow monitor command.
show flow monitor [name]
Syntax Description
name |
(Optional) Name of an existing flow monitor. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display information about the flow monitor called MonitorTest:
n1000v(config-flow-monitor)# show flow monitor MonitorTest
Flow Monitor monitortest:
Use count: 0
Inactive timeout: 600
Active timeout: 1800
Cache Size: 15000
n1000v(config-flow-monitor)#
Related Commands
show flow record
To display information about NetFlow flow records, use the show flow record command.
show flow record [recordname | netflow-original | netflow {ipv4 {original-input | original-output | protocol-port}}]
Syntax Description
Defaults
None
Command Modes
CLI flow exporter configuration (config-flow-exporter)
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display information about the NetFlow flow record called RecordTest:
n1000v# config t
n1000v(config)# flow record RecordTest
n1000v(config-flow-record)# show flow record RecordTest
Flow record RecordTest:
Description: Ipv4flow
No. of users: 0
Template ID: 0
Fields:
match ipv4 destination address
match interface input
match interface output
match flow direction
collect counter packets
n1000v(config-flow-record)#
Related Commands
show interface brief
To display a short version of the interface configuration, use the show interface brief command.
show interface brief
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to to display a short version of the interface configuration:
n1000v# show int brief
--------------------------------------------------------------------------------
Port VRF Status IP Address Speed MTU
--------------------------------------------------------------------------------
mgmt0 -- up 172.23.232.141 1000 1500
--------------------------------------------------------------------------------
Ethernet VLAN Type Mode Status Reason Speed Port
Interface Ch #
--------------------------------------------------------------------------------
Eth3/2 1 eth trunk up none 1000(D) --
Eth3/3 1 eth access up none 1000(D) --
n1000v#
Related Commands
show interface capabilities
To display information about the capabilities of the interfaces, use the show interface capabilities command.
show interface capabilities
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any configuration mode
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display information about the capabilities of the interfaces:
n1000v# show interface capabilities
mgmt0
Model: --
Type: --
Speed: 10,100,1000,auto
Duplex: half/full/auto
Trunk encap. type: 802.1Q
Channel: no
Broadcast suppression: none
Flowcontrol: rx-(none),tx-(none)
Rate mode: none
QOS scheduling: rx-(none),tx-(none)
CoS rewrite: yes
ToS rewrite: yes
SPAN: yes
UDLD: yes
Link Debounce: no
Link Debounce Time: no
MDIX: no
Port Group Members: none
port-channel1
Model: unavailable
Type: unknown
Speed: 10,100,1000,10000,auto
Duplex: half/full/auto
Trunk encap. type: 802.1Q
Channel: yes
Broadcast suppression: percentage(0-100)
Flowcontrol: rx-(off/on/desired),tx-(off/on/desired)
Rate mode: none
QOS scheduling: rx-(none),tx-(none)
CoS rewrite: yes
ToS rewrite: yes
SPAN: yes
UDLD: no
Link Debounce: no
Link Debounce Time: no
MDIX: no
Port Group Members: none
port-channel2
Model: unavailable
Type: unknown
Speed: 10,100,1000,10000,auto
Duplex: half/full/auto
Trunk encap. type: 802.1Q
Channel: yes
Broadcast suppression: percentage(0-100)
Flowcontrol: rx-(off/on/desired),tx-(off/on/desired)
Rate mode: none
QOS scheduling: rx-(none),tx-(none)
CoS rewrite: yes
ToS rewrite: yes
SPAN: yes
UDLD: no
Link Debounce: no
Link Debounce Time: no
MDIX: no
Port Group Members: none
port-channel12
Model: unavailable
Type: unknown
Speed: 10,100,1000,10000,auto
Duplex: half/full/auto
Trunk encap. type: 802.1Q
Channel: yes
Broadcast suppression: percentage(0-100)
Flowcontrol: rx-(off/on/desired),tx-(off/on/desired)
Rate mode: none
QOS scheduling: rx-(none),tx-(none)
CoS rewrite: yes
ToS rewrite: yes
SPAN: yes
UDLD: no
Link Debounce: no
Link Debounce Time: no
MDIX: no
Port Group Members: none
control0
Model: --
Type: --
Speed: 10,100,1000,auto
Duplex: half/full/auto
Trunk encap. type: 802.1Q
Channel: no
Broadcast suppression: none
Flowcontrol: rx-(none),tx-(none)
Rate mode: none
QOS scheduling: rx-(none),tx-(none)
CoS rewrite: yes
ToS rewrite: yes
SPAN: yes
UDLD: yes
Link Debounce: no
Link Debounce Time: no
MDIX: no
Port Group Members: none
n1000v#
Related Commands
show interface counters trunk
To display the counters for Layer 2 switch port trunk interfaces, use the show interface counters trunk command.
show interface {ethernet slot/port} counters trunk
Syntax Description
ethernet slot/port |
Specifies the module number and port number for the trunk interface that you want to display. |
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
The device supports only IEEE 802.1Q encapsulation. This command also displays the counters for trunk port channels.
Examples
This example shows how to display the counters for a trunk interface. This display shows the frames transmitted and received through the trunk interface, as well as the number of frames with the wrong trunk encapsulation:
n1000v# show interface ethernet 2/9 counters trunk
---------------------------------------------------------------------
Port TrunkFramesTx TrunkFramesRx WrongEncap
---------------------------------------------------------------------
Ethernet2/9 0 0 0
n1000v#
Related Commands
|
|
|
|---|---|
clear counters interface |
Clears the counters for the specified interfaces. |
show interface ethernet
To display information about Ethernet interfaces, use the show interface ethernet command.
show interface ethernet slot/port [brief | capabilities | debounce | description | flowcontrol | mac-address | switchport | trunk]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
4.0(4)SV1(2) |
Displays 5-minute input and output packet/bit rate statistics for the specified Ethernet interface. |
Examples
This example shows how to display statistical information for Ethernet interface 3/2:
n1000v# show interface ethernet 3/2
Ethernet3/2 is up
Hardware: Ethernet, address: 0050.5652.a9ba (bia 0050.5652.a9ba)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 0/255, txload 0/255, rxload 0/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 1000 Mb/s
Beacon is turned off
Auto-Negotiation is turned off
Input flow-control is off, output flow-control is off
Auto-mdix is turned on
Switchport monitor is off
5 minute input rate 570 bytes/second, 6 packets/second
5 minute output rate 220 bytes/second, 0 packets/second
Rx
7570522 Input Packets 1120178 Unicast Packets
5340163 Multicast Packets 1110181 Broadcast Packets
647893616 Bytes
Tx
1177170 Output Packets 1168661 Unicast Packets
7269 Multicast Packets 1240 Broadcast Packets 0 Flood Packets
252026472 Bytes
4276048 Input Packet Drops 0 Output Packet Drops
1 interface resets
Related Commands
|
|
|
|---|---|
clear interface |
Clears the interface statistics. |
show interface ethernet counters
To display the counters for an Ethernet interface, use the show interface ethernet counters command.
show interface ethernet slot/port counters [brief | detailed | errors | snmp | storm-control | trunk]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display counters for Ethernet interface 3/2:
n1000v# show interface ethernet 3/2 counters
--------------------------------------------------------------------------------
Port InOctets InUcastPkts InMcastPkts InBcastPkts
--------------------------------------------------------------------------------
Eth3/2 684023652 1182824 5637863 1171780
--------------------------------------------------------------------------------
Port OutOctets OutUcastPkts OutMcastPkts OutBcastPkts
--------------------------------------------------------------------------------
n1000v# 265927107 1233866 7269 1240
Related Commands
|
|
|
|---|---|
clear interface |
Clears the interface statistics. |
show interface ethernet status
To display the status for an Ethernet interface, use the show interface ethernet status command.
show interface ethernet slot/port status [err-disable]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the err-disabled status for Ethernet interface 3/2:
n1000v# show interface ethernet 3/2 status err-disabled
--------------------------------------------------------------------------------
Port Name Status Reason
--------------------------------------------------------------------------------
Eth3/2 -- up none
Related Commands
|
|
|
|---|---|
clear interface |
Clears the interface statistics. |
show interface ethernet transceiver
To display the transceiver information for an Ethernet interface, use the show interface ethernet transceiver command.
show interface ethernet slot/port transceiver [calibrations | details]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display transceiver information for Ethernet interface 3/2:
n1000v# show interface ethernet 3/2 transceiver calibrations
Ethernet3/2
sfp is not applicable
Related Commands
|
|
|
|---|---|
clear interface |
Clears the interface statistics. |
show interface port-channel
To display descriptive information about port channels, use the show interface port-channel command.
show interface port-channel channel-number [brief | description | flowcontrol | status | switchport | trunk]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
To display more statistics for the specified port channels, use the show interface port-channel counters command.
Examples
This example shows how to display information for a specific port channel. This command displays statistical information gathered on the port channel at 1-minute intervals:
n1000v(config)# show interface port-channel 50
port-channel50 is down (No operational members)
Hardware is Port-Channel, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 100000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is access
auto-duplex, auto-speed
Beacon is turned off
Input flow-control is off, output flow-control is off
Switchport monitor is off
Members in this channel: Eth2/10
Last clearing of "show interface" counters 2d71.2uh
5 minute input rate 0 bytes/sec, 0 packets/sec
5 minute output rate 0 bytes/sec, 0 packets/sec
Rx
0 input packets 0 unicast packets 0 multicast packets
0 broadcast packets 0 jumbo packets 0 storm suppression packets
0 bytes
Tx
0 output packets 0 multicast packets
0 broadcast packets 0 jumbo packets
0 bytes
0 input error 0 short frame 0 watchdog
0 no buffer 0 runt 0 CRC 0 ecc
0 overrun 0 underrun 0 ignored 0 bad etype drop
0 bad proto drop 0 if down drop 0 input with dribble
0 input discard
0 output error 0 collision 0 deferred
0 late collision 0 lost carrier 0 no carrier
0 babble
0 Rx pause 0 Tx pause 0 reset
This example shows how to display a brief description for a specific port channel, including the mode for the port channel, the status, speed, and protocol:
n1000v# show interface port-channel 5 brief
--------------------------------------------------------------------------------
Port-channel VLAN Type Mode Status Reason Speed Protocol
Interface
--------------------------------------------------------------------------------
eth access down No operational members auto(D) lacp
This example shows how to display the description for a specific port channel:
n1000v# show interface port-channel 5 description
-------------------------------------------------------------------------------
Interface Description
-------------------------------------------------------------------------------
port-channel5 test
This example shows how to display the flow-control information for a specific port channel:
n1000v# show interface port-channel 50 flowcontrol
------------------------------------------------------------------------------
Port Send FlowControl Receive FlowControl RxPause TxPause
admin oper admin oper
------------------------------------------------------------------------------
Po50 off off off off 0 0
This example shows how to display the status of a specific port channel:
n1000v# show interface port-channel 5 status
--------------------------------------------------------------------------------
Port Name Status Vlan Duplex Speed Type
--------------------------------------------------------------------------------
test down 1 auto auto --
This example shows how to display information for a specific Layer 2 port channel:
n1000v# show interface port-channel 50 switchport
Name: port-channel50
Switchport: Enabled
Switchport Monitor: Not enabled
Operational Mode: trunk
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: 1-3967,4048-4093
Administrative private-vlan primary host-association: none
Administrative private-vlan secondary host-association: none
Administrative private-vlan primary mapping: none
Administrative private-vlan secondary mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk private VLANs: none
Operational private-vlan: none
This command displays information for Layer 2 port channels in both the access and trunk modes.
When you use this command for a routed port channel, the device returns the following message:
Name: port-channel20
Switchport: Disabled
This example shows how to display information for a specific Layer 2 port channel that is in trunk mode:
n1000v# show interface port-channel 5 trunk
n1000v# show interface port-channel 50 trunk
port-channel50 is down (No operational members)
Hardware is Ethernet, address is 0000.0000.0000
MTU 1500 bytes, BW 100000 Kbit, DLY 10 usec
Port mode is access
Speed is auto-speed
Duplex mode is auto
Beacon is turned off
Receive flow-control is off, Send flow-control is off
Rate mode is dedicated
Members in this channel: Eth2/10
Native Vlan: 1
Allowed Vlans: 1-3967,4048-4093
This command displays information for only Layer 2 port channels in the trunk modes; you cannot display information about Layer 2 port channels in the access mode with this command.
Related Commands
|
|
|
|---|---|
show interface port-channel counters |
Displays the statistics for channel groups. |
show port-channel summary |
Displays summary information for all channel groups. |
show interface port-channel counters
To display information about port-channel statistics, use the show interface port-channel counters command.
show interface port-channel channel-number counters [brief | detailed [all | snmp] | errors [snmp] | trunk]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
This command displays statistics for all port channels including LACP-enabled port channels and those port channels that are not associated with an aggregation protocol.
Examples
This example shows how to display the counters for a specific port channel. This display shows the transmitted and received unicast and multicast packets:
n1000v# show interface port-channel 2 counters
Port InOctets InUcastPkts InMcastPkts InBcastPkts
Po2 6007 1 31 1
Port OutOctets OutUcastPkts OutMcastPkts OutBcastPkts
Po2 4428 1 25 1
n1000v#
This example shows how to display the brief counters for a specific port channel. This display shows the transmitted and received rate and total frames:
n1000v# show interface port-channel 20 counters brief
-------------------------------------------------------------------------------
Interface Input (rate is 1 min avg) Output (rate is 1 min avg)
------------------------- -----------------------------
Rate Total Rate Total
MB/s Frames MB/s Frames
-------------------------------------------------------------------------------
port-channel20 0 0 0 0
This example shows how to display all the detailed counters for a specific port channel:
n1000v# show interface port-channel 20 counters detailed all
port-channel20
64 bit counters:
0. rxHCTotalPkts = 0
1. txHCTotalPks = 0
2. rxHCUnicastPkts = 0
3. txHCUnicastPkts = 0
4. rxHCMulticastPkts = 0
5. txHCMulticastPkts = 0
6. rxHCBroadcastPkts = 0
7. txHCBroadcastPkts = 0
8. rxHCOctets = 0
9. txHCOctets = 0
10. rxTxHCPkts64Octets = 0
11. rxTxHCpkts65to127Octets = 0
12. rxTxHCpkts128to255Octets = 0
13. rxTxHCpkts256to511Octets = 0
14. rxTxHCpkts512to1023Octets = 0
15. rxTxHCpkts1024to1518Octets = 0
16. rxTxHCpkts1519to1548Octets = 0
17. rxHCTrunkFrames = 0
18. txHCTrunkFrames = 0
19. rxHCDropEvents = 0
All Port Counters:
0. InPackets = 0
1. InOctets = 0
2. InUcastPkts = 0
3. InMcastPkts = 0
4. InBcastPkts = 0
5. InJumboPkts = 0
6. StormSuppressPkts = 0
7. OutPackets = 0
8. OutOctets = 0
9. OutUcastPkts = 0
10. OutMcastPkts = 0
11. OutBcastPkts = 0
12. OutJumboPkts = 0
13. rxHCPkts64Octets = 0
14. rxHCPkts65to127Octets = 0
15. rxHCPkts128to255Octets = 0
16. rxHCPkts256to511Octets = 0
17. rxHCpkts512to1023Octets = 0
18. rxHCpkts1024to1518Octets = 0
19. rxHCpkts1519to1548Octets = 0
20. txHCPkts64Octets = 0
21. txHCPkts65to127Octets = 0
22. txHCPkts128to255Octets = 0
23. txHCPkts256to511Octets = 0
24. txHCpkts512to1023Octets = 0
25. txHCpkts1024to1518Octets = 0
26. txHCpkts1519to1548Octets = 0
27. ShortFrames = 0
28. Collisions = 0
29. SingleCol = 0
30. MultiCol = 0
31. LateCol = 0
32. ExcessiveCol = 0
33. LostCarrier = 0
34. NoCarrier = 0
35. Runts = 0
36. Giants = 0
37. InErrors = 0
38. OutErrors = 0
39. InputDiscards = 0
40. BadEtypeDrops = 0
41. IfDownDrops = 0
42. InUnknownProtos = 0
43. txCRC = 0
44. rxCRC = 0
45. Symbol = 0
46. txDropped = 0
47. TrunkFramesTx = 0
48. TrunkFramesRx = 0
49. WrongEncap = 0
50. Babbles = 0
51. Watchdogs = 0
52. ECC = 0
53. Overruns = 0
54. Underruns = 0
55. Dribbles = 0
56. Deferred = 0
57. Jabbers = 0
58. NoBuffer = 0
59. Ignored = 0
60. bpduOutLost = 0
61. cos0OutLost = 0
62. cos1OutLost = 0
63. cos2OutLost = 0
64. cos3OutLost = 0
65. cos4OutLost = 0
66. cos5OutLost = 0
67. cos6OutLost = 0
68. cos7OutLost = 0
69. RxPause = 0
70. TxPause = 0
71. Resets = 0
72. SQETest = 0
73. InLayer3Routed = 0
74. InLayer3RoutedOctets = 0
75. OutLayer3Routed = 0
76. OutLayer3RoutedOctets = 0
77. OutLayer3Unicast = 0
78. OutLayer3UnicastOctets = 0
79. OutLayer3Multicast = 0
80. OutLayer3MulticastOctets = 0
81. InLayer3Unicast = 0
82. InLayer3UnicastOctets = 0
83. InLayer3Multicast = 0
84. InLayer3MulticastOctets = 0
85. InLayer3AverageOctets = 0
86. InLayer3AveragePackets = 0
87. OutLayer3AverageOctets = 0
88. OutLayer3AveragePackets = 0
This example shows how to display the error counters for a specific port channel:
n1000v# show interface port-channel 5 counters errors
--------------------------------------------------------------------------------
Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize OutDiscards
--------------------------------------------------------------------------------
Po5 0 0 0 0 0 0
--------------------------------------------------------------------------------
Port Single-Col Multi-Col Late-Col Exces-Col Carri-Sen Runts
--------------------------------------------------------------------------------
Po5 0 0 0 0 0 0
--------------------------------------------------------------------------------
Port Giants SQETest-Err Deferred-Tx IntMacTx-Er IntMacRx-Er Symbol-Err
--------------------------------------------------------------------------------
0 -- 0 0 0 0
This example shows how to display information about the trunk interfaces for a specific port channel:
n1000v# show interface port-channel 5 counters trunk
-------------------------------------------------------------------------------
Port TrunkFramesTx TrunkFramesRx WrongEncap
-------------------------------------------------------------------------------
port-channel5 0 0 0
Related Commands
|
|
|
|---|---|
clear counters interface port-channel |
Clears the statistics for all interfaces that belong to a specific channel group. |
show interface status
To display the interface line status, use the show interface status command.
show interface status [down | err-disabled | inactive | module module-number | up]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display line status for interfaces in the up state:
n1000v# show interface status up
--------------------------------------------------------------------------------
Port Name Status Vlan Duplex Speed Type
--------------------------------------------------------------------------------
mgmt0 -- up routed full 1000 --
ctrl0 -- up routed full 1000 --
n1000v#
Related Commands
show interface switchport
To display information about switchport interfaces, use the show interface switchport command.
show interface [ethernet slot number| port-channel channel number] switchport
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
If you do not specify an interface, this command displays information about all Layer 2 interfaces, including access, trunk, and port channel interfaces and all private VLAN ports.
Examples
This example shows how to display information for all Layer 2 interfaces:
n1000v# show interface switchport
Name: Ethernet2/5
Switchport: Enabled
Switchport Monitor: Not enabled
Operational Mode: access
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: 1-3967,4048-4093
Administrative private-vlan primary host-association: none
Administrative private-vlan secondary host-association: none
Administrative private-vlan primary mapping: none
Administrative private-vlan secondary mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk private VLANs: none
Operational private-vlan: none
Name: Ethernet2/9
Switchport: Enabled
Switchport Monitor: Not enabled
Operational Mode: trunk
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: 1-3967,4048-4093
Administrative private-vlan primary host-association: none
Administrative private-vlan secondary host-association: none
Administrative private-vlan primary mapping: none
Administrative private-vlan secondary mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk private VLANs: none
Operational private-vlan: none
Name: port-channel5
Switchport: Enabled
Switchport Monitor: Not enabled
Operational Mode: access
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: 1-3967,4048-4093
Administrative private-vlan primary host-association: none
Administrative private-vlan secondary host-association: none
Administrative private-vlan primary mapping: none
Administrative private-vlan secondary mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk private VLANs: none
Operational private-vlan: none
n1000v#
Related Commands
|
|
|
|---|---|
switchport mode |
Sets the specified interfaces as either Layer 2 access or trunk interfaces. |
show interface counters |
Displays statistics for a specified Layer 2 interface. |
show interface trunk
To display information about all the trunk interfaces, use the show interface trunk command.
show interface [ethernet type/slot | port-channel channel-number] trunk [module number | vlan vlan-id]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
If you do not specify an interface, a module number or a VLAN number, the system displays information for all trunk interfaces.
This command displays information about all Layer 2 trunk interfaces and trunk port-channel interfaces.
Use the show interface counters command to display statistics for the specified Layer 2 interface.
Examples
This example shows how to display information for all Layer 2 trunk interfaces:
n1000v(config)# show interface trunk
-----------------------------------------------------------------------------
Port Native Status Port
Vlan Channel
-----------------------------------------------------------------------------
Eth2/9 1 trunking --
Eth2/10 1 trnk-bndl Po50
Po50 1 not-trunking --
-----------------------------------------------------------------------------
Port Vlans Allowed on Trunk
-----------------------------------------------------------------------------
Eth2/9 1-3967,4048-4093
Eth2/10 1-3967,4048-4093
Po50 1-3967,4048-4093
-----------------------------------------------------------------------------
Port STP Forwarding
-----------------------------------------------------------------------------
Eth2/9 none
Eth2/10 none
Po50 none
n1000v#
Related Commands
|
|
|
|---|---|
switchport mode trunk |
Sets the specified interfaces as Layer 2 trunk interfaces. |
show interface vethernet
To display statistical information about vEthernet interfaces, use the show interface vethernet command.
show interface vethernet interface-number [brief | description | mac-address | switchport | trunk]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(2) |
This command was introduced. |
4.0(4)SV1(2) |
Displays 5-minute input and output packet/bit rate statistics for the specified vEthernet interface. |
Examples
This example shows how to display statistical information for vEthernet interface 1:
n1000v# show interface vethernet 1
Vethernet1 is up
Port description is gentoo, Network Adapter 1
Hardware is Virtual, address is 0050.5687.3bac
Owner is VM "gentoo", adapter is Network Adapter 1
Active on module 4
VMware DVS port 1
Port-Profile is vm
Port mode is access
5 minute input rate 1 bytes/second, 0 packets/second
5 minute output rate 94 bytes/second, 1 packets/second
Rx
655 Input Packets 594 Unicast Packets
0 Multicast Packets 61 Broadcast Packets
114988 Bytes
Tx
98875 Output Packets 1759 Unicast Packets
80410 Multicast Packets 16706 Broadcast Packets 0 Flood Packets
6368452 Bytes
0 Input Packet Drops 0 Output Packet Drops
Related Commands
|
|
|
|---|---|
clear interface |
Clears the interface statistics. |
show interface vethernet counters
To display the counters for a vEthernet interface, use the show interface vethernet counters command.
show interface vethernet interface-number counters [brief | detailed | errors | trunk]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display counters for vEthernet interface 1:
n1000v# show interface vethernet 1 counters
--------------------------------------------------------------------------------
Port InOctets InUcastPkts InMcastPkts InBcastPkts
--------------------------------------------------------------------------------
Veth1 2434320 5024 12 32363
--------------------------------------------------------------------------------
Port OutOctets OutUcastPkts OutMcastPkts OutBcastPkts
--------------------------------------------------------------------------------
Veth1 4357946 4910 127 64494
Related Commands
|
|
|
|---|---|
clear interface |
Clears the interface statistics. |
show interface vethernet status
To display the status for a vEthernet interface, use the show interface vethernet status command.
show interface vethernet interface-number status [err-disable]
Syntax Description
interface-number |
Number of the interface that you want to display. The range is from 1 to 1048575. |
err-disabled |
(Optional) Specifies to display the err-disabled state for the specified interface. |
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the err-disabled status for vEthernet interface 1:
n1000v# show interface vethernet 1 status err-disabled
--------------------------------------------------------------------------------
Port Name Status Reason
--------------------------------------------------------------------------------
Veth1 VM1-48, Network Ad up none
n1000v#
Related Commands
|
|
|
|---|---|
clear interface |
Clears the interface statistics. |
show interface virtual
To display information about virtual interfaces, use the show interface virtual command.
show interface virtual [vm [vm_name] | vmk | vswif] [module module_number]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display information for virtual interfaces:
n1000v# show interface virtual
--------------------------------------------------------------------------------
Port Adapter Owner Mod Host
--------------------------------------------------------------------------------
Veth1 Vm1-kl61 2
Veth2 VM1-kl65 5
Veth3 VM2-kl61 2
Veth1 Net Adapter 1 austen-gentoo1 33 austen-strider.austen.
Veth2 Net Adapter 2 austen-gentoo1 33 austen-strider.austen.
n1000v#
Related Commands
show interface virtual port-mapping
To display the virtual port mapping for all vEthernet interfaces, use the show interface virtual port-mapping command.
show interface virtual port-mapping [vm [vm_name] | vmk | vswif] [module module_number]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the virtual port mapping for all vEthernet interfaces:
n1000v# show interface virtual port-mapping
--------------------------------------------------------------------------------
Port Hypervisor Port Status Reason
--------------------------------------------------------------------------------
Veth1 DVPort100 up none
Veth2 DVPort160 up none
n1000v#
Related Commands
show ip access-list
To display all IPv4 access control lists (ACLs) or a specific IPv4 AC, use the show ip access-list command.
show ip access-list [name]
Syntax Description
name |
(Optional) Name of an existing IPv4 access control list. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the IPv4 access control list called protoacl:
n1000v(config)# show ip access-lists protoacl
IP access list protoacl
statistics per-entry
10 permit icmp 7.120.1.10/32 7.120.1.20/32
20 permit tcp 7.120.1.10/32 7.120.1.20/32 dscp af11
30 permit udp 7.120.1.10/32 7.120.1.20/32 precedence critical
50 permit ip 7.120.1.20/32 7.120.1.10/32
60 permit ip 7.120.1.20/32 7.120.1.10/32 dscp af11
70 permit ip 7.120.1.20/32 7.120.1.10/32 precedence critical
n1000v#
Related Commands
show ip access-list summary
To display the IP ACL configuration, use the show ip access-list command.
show ip access-list [name] summary
Syntax Description
name |
(Optional) Name of an existing IPv4 access control list. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
If the ACL remains applied to an interface, this command lists the interfaces.
Examples
This example shows how to display the IPv4 access control list called ACL1:
n1000v# show ip access-lists summary IPV4 ACL1
Total ACEs Configured: 1
Configured on interfaces:
Vethernet1 - ingress (Port ACL)
Active on interfaces:
Vethernet1 - ingress (Port ACL)
n1000v#
Related Commands
show ip arp client
To display the ARP client table, use the show ip arp client command.
show ip arp client
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the ARP client table:
n1000v# show ip arp client
Number of ARP Clients: 1
Protocol uuid: 442, Client type: L2
Flags: 8, Recv fn: dhcp_snoop_verify_mac2ip_binding
n1000v#
Related Commands
.
show ip arp inspection interface
To display the trust state for the specified interface, use the show ip arp inspection interface command.
show ip arp inspection interface vethernet interface-number
Syntax Description
vethernet number |
Specifies that the output is for a vEthernet interface. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(2) |
This command was introduced. |
Examples
This example shows how to display the trust state for a trusted interface:
n1000v# show ip arp inspection interface vethernet 6
Interface Trust State
------------- -----------
vEthernet 6 Trusted
n1000v#
Related Commands
|
|
|
|---|---|
ip arp inspection vlan |
Enables Dynamic ARP Inspection (DAI) for a specified list of VLANs. |
show ip arp inspection statistics |
Displays the DAI statistics. |
show ip arp inspection statistics
Use the show ip arp inspection statistics command to display the Dynamic ARP Inspection (DAI) statistics. You can specify a VLAN or range of VLANs.
show ip arp inspection statistics [vlan vlan-list]
Syntax Description
vlan vlan-list |
(Optional) Specifies the list of VLANs for which to display DAI statistics. Valid VLAN IDs are from 1 to 4096. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(2) |
This command was introduced. |
Examples
This example shows how to display the DAI statistics for VLAN 1:
n1000v# show ip arp inspection statistics vlan 1
Vlan : 1
-----------
ARP Req Forwarded = 0
ARP Res Forwarded = 0
ARP Req Dropped = 0
ARP Res Dropped = 0
DHCP Drops = 0
DHCP Permits = 0
SMAC Fails-ARP Req = 0
SMAC Fails-ARP Res = 0
DMAC Fails-ARP Res = 0
IP Fails-ARP Req = 0
IP Fails-ARP Res = 0
n1000v#
Related Commands
show ip arp inspection vlan
To display the Dynamic ARP Inspection (DAI) status for the specified list of VLANs, use the show ip arp inspection vlan command.
show ip arp inspection vlan list
Syntax Description
list |
Number identifying an existing VLAN, or range of VLANs, from 1-3967 and 4048-4093. You can specify groups of VLANs or individual VLANs; for example, 1-5, 10 or 2-5, 7-19. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the DAI status for VLAN 13:
n1000v# show ip arp inspection vlan 13
Source Mac Validation : Disabled
Destination Mac Validation : Enabled
IP Address Validation : Enabled
n1000v#
Related Commands
show ip arp statistics
To display the ARP statistics, use the show ip arp statistics command.
show ip arp statistics [interface-all] [vrf {name | all | default | management}]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display ARP statistics for all VRFs:
n1000v# show ip arp statistics vrf all
ARP packet statistics for all contexts
Sent:
Total 101994, Requests 3920, Replies 98074, Requests on L2 0, Replies on L2 0,
Gratuitous 2, Dropped 0
Received:
Total 8070240, Requests 98074, Replies 4034, Requests on L2 0, Replies on L2 0
Proxy arp 0, Local-Proxy arp 0, Dropped 7968132
Received packet drops details:
Appeared on a wrong interface : 0
Incorrect length : 0
Invalid protocol packet : 228
Invalid context : 0
Context not yet created : 0
Invalid layer 2 address length : 0
Invalid layer 3 address length : 0
Invalid source IP address : 221153
Source IP address is our own : 0
No mem to create per intf structure : 0
Source address mismatch with subnet : 0
Directed broadcast source : 0
Invalid destination IP address : 0
Non-local destination IP address : 7746751
Invalid source MAC address : 0
Source MAC address is our own : 0
Received before arp initialization : 0
Received packet on unknown iod : 0
L2 packet on proxy-arp-enabled interface
: 0
L2 packet on untrusted L2 port : 0
ARP adjacency statistics
Adds 13, Deletes 11, Timeouts 11
Related Commands
show ip dhcp snooping
To display general status information for DHCP snooping, use the show ip dhcp snooping command.
show ip dhcp snooping
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(2) |
This command was introduced. |
Examples
This example shows how to display general status information about DHCP snooping:
n1000v# show ip dhcp snooping
DHCP snooping service is enabled
Switch DHCP snooping is enabled
DHCP snooping is configured on the following VLANs:
1,13
DHCP snooping is operational on the following VLANs:
1
Insertion of Option 82 is disabled
Verification of MAC address is enabled
DHCP snooping trust is configured on the following interfaces:
Interface Trusted
------------ -------
vEthernet 3 Yes
n1000v#
Related Commands
show ip dhcp snooping binding
To display IP-to-MAC address bindings for all interfaces or a specific interface, use the show ip dhcp snooping binding command.
show ip dhcp snooping binding [IP-address] [MAC-address] [interface vethernet interface-number] [vlan vlan-id]
show ip dhcp snooping binding [dynamic]
show ip dhcp snooping binding [static]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(2) |
This command was introduced. |
Usage Guidelines
The command output includes static IP source entries. Static entries appear with the term "static" in the Type column.
Examples
This example shows how to show all bindings:
n1000v# show ip dhcp snooping binding
MacAddress IpAddress LeaseSec Type VLAN Interface
----------------- --------------- -------- ---------- ---- -------------
0f:00:60:b3:23:33 10.3.2.2 infinite static 13 vEthernet 6
0f:00:60:b3:23:35 10.2.2.2 infinite static 100 vEthernet 10
n1000v#
Related Commands
|
|
|
|---|---|
ip dhcp snooping |
Globally enables DHCP snooping on the device. |
show ip dhcp snooping |
Displays general information about DHCP snooping. |
show ip dhcp snooping statistics
To display statistics related to the Dynamic Host Configuration Protocol (DHCP), use the show ip dhcp snooping statistics command.
show ip dhcp snooping statistics
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
Before you can configure DHCP, you must enable the feature using the feature dhcp command.
Examples
This example shows how to display statistics related to DHCP:
n1000v# show ip dhcp snooping statistics
Packets processed 0
Packets received through cfsoe 0
Packets forwarded 0
Total packets dropped 0
Packets dropped from untrusted ports 0
Packets dropped due to MAC address check failure 0
Packets dropped due to Option 82 insertion failure 0
Packets dropped due to o/p intf unknown 0
Packets dropped which were unknown 0
Packets dropped due to dhcp relay not enabled 0
Packets dropped due to no binding entry 0
Packets dropped due to interface error/no interface 0
Packets dropped due to max hops exceeded 0
n1000v#
Related Commands
show ip igmp snooping
To ensure that IGMP snooping is enabled on the VLAN, use the show ip igmp snooping command.
show ip igmp snooping
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to ensure that IGMP snooping is enabled on the VLAN:
n1000v# show ip igmp snooping
Global IGMP Snooping Information:
IGMP Snooping enabled
IGMPv1/v2 Report Suppression enabled
IGMPv3 Report Suppression disabled
IGMP Snooping information for vlan 1
IGMP snooping enabled
IGMP querier none
Switch-querier disabled
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Router port detection using PIM Hellos, IGMP Queries
Number of router-ports: 0
Number of groups: 0
IGMP Snooping information for vlan 2
IGMP snooping enabled
IGMP querier none
Switch-querier disabled
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Router port detection using PIM Hellos, IGMP Queries
Number of router-ports: 0
Number of groups: 0
IGMP Snooping information for vlan 100
IGMP snooping enabled
IGMP querier none
Switch-querier disabled
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Router port detection using PIM Hellos, IGMP Queries
Number of router-ports: 0
Number of groups: 0
IGMP Snooping information for vlan 101
IGMP snooping enabled
IGMP querier none
Switch-querier disabled
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Router port detection using PIM Hellos, IGMP Queries
Number of router-ports: 0
Number of groups: 0
IGMP Snooping information for vlan 102
IGMP snooping enabled
IGMP querier none
Switch-querier disabled
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Router port detection using PIM Hellos, IGMP Queries
Number of router-ports: 0
Number of groups: 0
IGMP Snooping information for vlan 103
IGMP snooping enabled
IGMP querier none
Switch-querier disabled
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Router port detection using PIM Hellos, IGMP Queries
Number of router-ports: 0
Number of groups: 0
IGMP Snooping information for vlan 104
IGMP snooping enabled
IGMP querier none
Switch-querier disabled
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Router port detection using PIM Hellos, IGMP Queries
Number of router-ports: 0
Number of groups: 0
IGMP Snooping information for vlan 105
IGMP snooping enabled
IGMP querier none
Switch-querier disabled
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Router port detection using PIM Hellos, IGMP Queries
Number of router-ports: 0
Number of groups: 0
IGMP Snooping information for vlan 106
IGMP snooping enabled
IGMP querier none
Switch-querier disabled
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Router port detection using PIM Hellos, IGMP Queries
Number of router-ports: 0
Number of groups: 0
IGMP Snooping information for vlan 107
IGMP snooping enabled
IGMP querier none
Switch-querier disabled
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Router port detection using PIM Hellos, IGMP Queries
Number of router-ports: 0
Number of groups: 0
IGMP Snooping information for vlan 108
IGMP snooping enabled
IGMP querier none
Switch-querier disabled
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Router port detection using PIM Hellos, IGMP Queries
Number of router-ports: 0
Number of groups: 0
IGMP Snooping information for vlan 109
IGMP snooping enabled
IGMP querier none
Switch-querier disabled
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Router port detection using PIM Hellos, IGMP Queries
Number of router-ports: 0
Number of groups: 0
IGMP Snooping information for vlan 115
IGMP snooping enabled
IGMP querier none
Switch-querier disabled
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Router port detection using PIM Hellos, IGMP Queries
Number of router-ports: 0
Number of groups: 0
IGMP Snooping information for vlan 260
IGMP snooping enabled
IGMP querier none
Switch-querier disabled
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Router port detection using PIM Hellos, IGMP Queries
Number of router-ports: 0
Number of groups: 0
IGMP Snooping information for vlan 261
IGMP snooping enabled
IGMP querier none
Switch-querier disabled
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Router port detection using PIM Hellos, IGMP Queries
Number of router-ports: 0
Number of groups: 0
n1000v#
Related Commands
show ip igmp snooping explicit-tracking vlan
To display IGMPv3 snooping explicit tracking information for a VLAN, use the show ip igmp snooping explicit-tracking vlan command.
show ip igmp snooping explicit-tracking vlan vlan-id
Syntax Description
vlan-id |
Specifies a VLAN ID. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
Examples
Related Commands
show ip igmp snooping groups
To verify if the Cisco Nexus 1000V is configured correctly and is ready to forward multicast traffic, use the show ip igmp snooping groups command.
show ip igmp snooping groups
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
When troubleshooting multicast IGMP issues, execute this command and look for the letter R under the port heading. The R indicates that the Virtual Supervisor Module (VSM) has learned the uplink router port from the IGMP query that was sent by the upstream switch, which means that the Cisco Nexus 1000V is ready to forward multicast traffic.
Examples
This example shows how to ensure that IGMP snooping is enabled on the VLAN:
n1000v# show ip igmp snooping groups
Type: S - Static, D - Dynamic, R - Router port
Vlan Group Address Ver Type Port list
59 */* v3 R Po1
n1000v#n1000v#
Related Commands
show ip igmp snooping mrouter
To display VLAN multicast router ports , use the show ip igmp snooping mrouter command.
show ip igmp snooping mrouter [vlan vlan-id]
Syntax Description
vlan vlan-id |
Specifies a VLAN and its ID. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
Examples
Related Commands
show ip igmp snooping querier
To display IGMP snooping querier information, use the show ip igmp snooping querier command.
show ip igmp snooping querier [vlan vlan-id]
Syntax Description
vlan vlan-id |
Specifies a VLAN and its ID. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
Examples
Related Commands
show ip verify source
To display the IP-to-MAC address bindings, use the show ip verify source command.
show ip verify source [ interface {vethernet interface-number }]
Syntax Description
interface |
(Optional) Specifies that the output is limited to IP-to-MAC address bindings for an interface. |
vethernet interface-number |
Specifies the vEthernet interface. Range is from 1 to 1048575. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(2) |
This command was introduced. |
Examples
This example shows how to display the IP-to-MAC address bindings:
n1000v# show ip verify source
n1000v#
Related Commands
|
|
|
|---|---|
ip source binding |
Creates a static IP source entry for the specified Ethernet interface. |
ip verify source dhcp-snooping-vlan |
Enables IP Source Guard on an interface. |
show lacp counters
To display information about Link Aggregation Control Protocol (LACP) statistics, use the show lacp counters command.
show lacp counters [interface port-channel channel-number]
Syntax Description
channel-number |
(Optional) Number of the LACP channel group. Valid values are from 1 to 4096. |
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
If you do not specify the channel-number, all channel groups are displayed.
Examples
This example shows how to display the LACP statistics for a specific channel group:
n1000v# show lacp counters interface port-channel 1
LACPDUs Marker Marker Response LACPDUs
Port Sent Recv Sent Recv Sent Recv Pkts Err
-----------------------------------------------------------------------------
port-channel1
Ethernet1/1 554 536 0 0 0 0 0
Ethernet1/2 527 514 0 0 0 0 0
Ethernet1/3 535 520 0 0 0 0 0
Ethernet1/4 515 502 0 0 0 0 0
Ethernet1/5 518 505 0 0 0 0 0
Ethernet1/6 540 529 0 0 0 0 0
Ethernet1/7 541 530 0 0 0 0 0
Ethernet1/8 547 532 0 0 0 0 0
Ethernet1/9 544 532 0 0 0 0 0
Ethernet1/10 513 501 0 0 0 0 0
Ethernet1/11 497 485 0 0 0 0 0
Ethernet1/12 493 486 0 0 0 0 0
Ethernet1/13 492 485 0 0 0 0 0
Ethernet1/14 482 481 0 0 0 0 0
Ethernet1/15 481 476 0 0 0 0 0
Ethernet1/16 482 477 0 0 0 0 0
Related Commands
|
|
|
|---|---|
clear lacp counters |
Clears the statistics for all LACP interfaces or those interfaces that belong to a specific LACP channel group. |
show lacp interface
To display information about specific Link Aggregation Control Protocol (LACP) interfaces, use the show lacp interface command.
show lacp interface ethernet slot/port
Syntax Description
slot/port |
Slot number and port number for the interface you want to display. |
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
The LACP_Activity field displays whether the link is configured in the active or passive port-channel mode.
The Port Identifier field displays the port priority as part of the information. The part of the information in this field is the port number. The following example shows how to identify the port priority and the port number:
Port Identifier=0x8000,0x101
The port priority value is 0x8000, and the port number value is 0x101 in this example.
Examples
This example shows how to display the LACP statistics for a specific channel group:
n1000v# show lacp interface ethernet 1/1
n1000v(config-if-range)# show lacp interface eth1/1
Interface Ethernet1/1 is up
Channel group is 1 port channel is Po1
PDUs sent: 556
PDUs rcvd: 538
Markers sent: 0
Markers rcvd: 0
Marker response sent: 0
Marker response rcvd: 0
Unknown packets rcvd: 0
Illegal packets rcvd: 0
Lag Id: [ [(8000, 0-11-11-22-22-74, 0, 8000, 101), (8000, 0-11-11-22-22-75, 0, 8
000, 401)] ]
Operational as aggregated link since Wed Jun 11 20:37:59 2008
Local Port: Eth1/1 MAC Address= 0-11-11-22-22-74
System Identifier=0x8000,0-11-11-22-22-74
Port Identifier=0x8000,0x101
Operational key=0
LACP_Activity=active
LACP_Timeout=Long Timeout (30s)
Synchronization=IN_SYNC
Collecting=true
Distributing=true
Partner information refresh timeout=Long Timeout (90s)
Actor Admin State=
Actor Oper State=
Neighbor: 4/1
MAC Address= 0-11-11-22-22-75
System Identifier=0x8000,0-11-11-22-22-75
Port Identifier=0x8000,0x401
Operational key=0
LACP_Activity=active
LACP_Timeout=Long Timeout (30s)
Synchronization=IN_SYNC
Collecting=true
Distributing=true
Partner Admin State=
Partner Oper State=
Related Commands
|
|
|
|---|---|
show port-channel summary |
Displays information about all port-channel groups. |
show lacp neighbor
To display information about Link Aggregation Control Protocol (LACP) neighbors, use the show lacp neighbor command.
show lacp neighbor [interface port-channel channel-number]
Syntax Description
channel-number |
Port-channel number for the LACP neighbor that you want to display. The range of values is from 1 to 4096. |
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
If you do not specify the channel-number, all channel groups are displayed.
Examples
This example shows how to display the information about the LACP neighbors for a specific port channel:
n1000v# show lacp neighbor interface port-channel 1
Flags: S - Device is sending Slow LACPDUs F - Device is sending Fast LACPDUs
A - Device is in Active mode P - Device is in Passive mode
port-channel1 neighbors
Partner's information
Partner Partner Partner
Port System ID Port Number Age Flags
Eth1/1 32768,0-11-11-22-22-750x401 44817 SA
LACP Partner Partner Partner
Port Priority Oper Key Port State
32768 0x0 0x3d
Partner's information
Partner Partner Partner
Port System ID Port Number Age Flags
Eth1/2 32768,0-11-11-22-22-750x402 44817 SA
LACP Partner Partner Partner
Port Priority Oper Key Port State
32768 0x0 0x3d
Related Commands
|
|
|
|---|---|
show port-channel summary |
Displays information about all port-channel groups. |
show lacp port-channel
To display information about Link Aggregation Control Protocol (LACP) port channels, use the show lacp port-channel command.
show lacp port-channel [interface port-channel channel-number]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
If you do not specify the channel-number, all channel groups are displayed.
Examples
This example shows how to display the information about LACP port channels:
n1000v# show lacp port-channel
port-channel1
Local System Identifier=0x8000,0-11-11-22-22-74
Admin key=0x0
Operational key=0x0
Partner System Identifier=0x8000,0-11-11-22-22-75
Operational key=0x0
Max delay=0
Aggregate or individual=1
port-channel2
Local System Identifier=0x8000,0-11-11-22-22-74
Admin key=0x1
Operational key=0x1
Partner System Identifier=0x8000,0-11-11-22-22-75
Operational key=0x1
Max delay=0
Aggregate or individual=1
Related Commands
|
|
|
|---|---|
show port-channel summary |
Displays information about all port-channel groups. |
show lacp system-identifier
To display the Link Aggregation Control Protocol (LACP) system identifier for the device, use the show lacp system-identifier command.
show lacp system-identifier
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
The LACP system ID is the combination of the configurable LACP system priority value and the MAC address.
Each system that runs LACP has an LACP system priority value. You can accept the default value of 32768 for this parameter, or you can configure a value between 1 and 65535. LACP uses the system priority with the MAC address to form the system ID and also uses the system priority during negotiation with other devices. A higher system priority value means a lower priority.
Examples
This example shows how to display the information about the LACP port channel for a specific port channel:
n1000v> show lacp system-identifier
8000,AC-12-34-56-78-90
Related Commands
|
|
|
|---|---|
lacp system-priority |
Sets the system priority for LACP. |
show license
To display the content of all the license files that are installed on the virtual supervisor module (VSM), use the show license command.
show license
Syntax Description
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the content of all the license files that are installed on the VSM:
n1000v# show license
license_file.lic:
SERVER this_host ANY
VENDOR cisco
INCREMENT NEXUS1000V_LAN_SERVICES_PKG cisco 1.0 permanent 16 \
HOSTID=VDH=8449368321243879080 \
NOTICE="<LicFileID>kathleen.lic</LicFileID><LicLineID>0</LicLineID> \
<PAK>dummyPak</PAK>" SIGN=34FCB2B24AE8
n1000v#
Related Commands
show license brief
To display a list of license files that are installed on the virtual supervisor module (VSM), use the show license brief command.
show license brief
Syntax Description
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the content of all the license files that are installed on the VSM:
n1000v# show license brief
license_file.lic
n1000v#
Related Commands
show license file
To verify the license installation by displaying the license configured for the Virtual Supervisor Module (VSM), use the show license file command.
show license file filename
Related Commands
filename |
Name of the existing license file (.lic). |
Defaults
None
Command Modes
Any
network-admin
network-operator
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
To find the name of the existing file, enter the following command at the prompt:
n1000v# show license file ?
Examples
This example shows how to display the license file, sample.lic, configured for the VSM:
n1000v# show license file sample.lic
sample.lic:
SERVER this_host ANY
VENDOR cisco
INCREMENT NEXUS1000V_LAN_SERVICES_PKG cisco 1.0 permanent 16 \
HOSTID=VDH=8449368321243879080 \
NOTICE="<LicFileID>sample.lic</LicFileID><LicLineID>0</LicLineID> \
<PAK>dummyPak</PAK>" SIGN=34FCB2B24AE8
n1000v#
Related Commands
show license host-id
To obtain the serial number, also called the host ID, for your Virtual Supervisor Module (VSM), use the show license host-id command.
show license host-id
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
The host ID includes everything that appears after the equal sign (=).
The host ID is required to obtain a license key file and register your VSM license.
Examples
This example shows how to obtain the host ID for your VSM:
n1000v# show license host-id
License hostid: VDH=8449368321243879080
n1000v#
Related Commands
show license usage
To display the various license packages that are supported on the virtual supervisor module (VSM), use the show license usage command.
show license usage [package-name]
Syntax Description
package-name |
(Optional) Name of a license file. In the Cisco Nexus 1000V, the VSM supports only one package (NEXUS1000V_LAN_SERVICES_PKG). |
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display a brief summary of the various license packages that are supported on the VSM:
n1000v# show license usage
Feature Ins Lic Status Expiry Date Comments
Count
--------------------------------------------------------------------------------
NEXUS1000V_LAN_SERVICES_PKG No 16 In use Never -
n1000v# ------------------------------------------------------------------------
This example shows how to display the license usage information for a specific license package:
Example:
n1000v# show license usage NEXUS1000V_LAN_SERVICES_PKG
--------------------------------------
Feature Usage Info
--------------------------------------
Installed Licenses : 10
Eval Licenses : 0
Max Overdraft Licenses : 16
Installed Licenses in Use : 4
Overdraft Licenses in Use : 0
Eval Licenses in Use : 0
Licenses Available : 22
--------------------------------------
Application
--------------------------------------
VEM 3 - Socket 1
VEM 3 - Socket 2
VEM 4 - Socket 1
VEM 4 - Socket 2
--------------------------------------
n1000v#
Syntax Description
show logging logfile
To display the contents of the log file, use the show logging logfile command.
show logging logfile [start-time time | end-time time]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the contents of the logfile:
n1000v# show logging logfile start-time 2009 Aug 23 22:00:00 end-time 2009 Aug 24 24:00:00
2009 Aug 23 22:58:00 doc-n1000v %PORTPROFILE-5-SYNC_COMPLETE: Sync completed.
2009 Aug 24 23:53:15 doc-n1000v %MODULE-5-MOD_OK: Module 3 is online (serial: )
2009 Aug 24 23:53:15 doc-n1000v %PLATFORM-5-MOD_STATUS: Module 3 current-status is MOD_S
TATUS_ONLINE/OK
n1000v#
Related Commands
|
|
|
|---|---|
logging logfile |
Configures the log file used to store system messages. |
show logging module
To display the current configuration for logging module messages to the log file, use the show logging module command.
show logging module
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the configuration for logging of messages to the log file:
n1000v# show logging module
Logging linecard: disabled
n1000v#
Related Commands
|
|
|
|---|---|
logging module |
Starts logging of module messages to the log file. |
show logging server
To display the current server configuration for logging system messages, use the show logging server command.
show logging server
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the :
n1000v## show logging server
Logging server: enabled
{172.28.254.253}
server severity: notifications
server facility: local7
server VRF: management
n1000v##
Related Commands
|
|
|
|---|---|
logging server |
Designates a remote server for system message logging, and configures it. |
show logging timestamp
To display the unit of measure used in the system messages timestamp, use the show logging timestamp command.
show logging timestamp
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the unit of measure used in the system messages timestamp:
n1000v## show logging timestamp
Logging timestamp: Seconds
n1000v##
Related Commands
|
|
|
|---|---|
logging timestamp |
Sets the unit of measure for the system messages timestamp. |
show mac access-lists
To display the MAC access control list (ACL) configuration, use the show mac access lists command.
show mac access-lists name
Syntax Description
name |
Enter the name of the MAC access list. |
Defaults
None
Command Modes
ACL configuration (config-mac-acl)
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the MAC ACL configuration for the MAC access list called acl-mac-01:
n1000v# config t
n1000v(config)# mac access-list acl-mac-01
n1000v(config-mac-acl)# show mac access-lists acl-mac-01
n1000v(config-mac-acl)#
Related Commands
|
|
|
|---|---|
mac access-list |
Creates the MAC ACL and enters ACL configuration mode. |
show mac address-list |
Displays the MAC address table. |
show mac address-table
To display the MAC address table, use the show mac address-table command.
show mac address-table [module number] [static | dynamic | secure] [address mac-addr] [interface {ethernet slot/port | port-channel port-channel-number |
vethernet interface -number}] [vlan id]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display static MAC addresses:
n1000v# show mac address-table static
Legend:
* - primary entry, G - Gateway MAC, (R) - Routed MAC
age - seconds since last seen
VLAN MAC Address Type age Secure NTFY Ports
---------+-----------------+--------+---------+------+------+----------------
G - 12ab.47dd.ff89 static - False False eth2/1
n1000v#
Related Commands
show mac address-table aging-time
To display the aging time in the MAC address table, use the show mac address-table aging-time command.
show mac address-table aging-time [vlan id]
Syntax Description
vlan |
(Optional) Specifies the VLAN associated with this MAC address table. |
id |
Identifier for the VLAN. The range is 1-4094. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the aging time in the MAC address table:
n1000v# show mac address-table aging-time
Vlan Aging Time
---- ----------
1 300
2 300
100 300
101 300
102 300
103 300
104 300
105 300
106 300
107 300
108 300
109 300
115 300
260 300
261 300
n1000v#
Related Commands
show module
To display module information, use the show module command.
show module [module-number | internal | ipv6-info | uptime | vem]
Related Commands
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display module information:
n1000v# show module
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ------------------ ------------
1 0 Virtual Supervisor Module Nexus1000V active *
Mod Sw Hw
--- --------------- ------
1 4.0(4)SV1(2) 0.0
Mod MAC-Address(es) Serial-Num
--- -------------------------------------- ----------
1 00-19-07-6c-5a-a8 to 00-19-07-6c-62-a8 NA
Mod Server-IP Server-UUID Server-Name
--- --------------- ------------------------------------ --------------------
1 172.23.232.152 NA NA
* this terminal session
n1000v#
Related Commands
show module vem mapping
To display information about the Virtual Ethernet Module (VEM) module mapping, use the show module vem mapping command.
show module vem [module-number] mapping
Related Commands
module-number |
(Optional) Number identifying an existing module. The range is 1-22. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display information about the host/module mapping:
n1000v# show module vem mapping
Mod Status UUID License Status
--- ----------- ------------------------------------ --------------
3 absent c43cfa32-08b4-4a12-b899-90f54fb05db0 licensed
n1000v#
Related Commands
|
|
|
|---|---|
show module |
Displays module information. |
module vem |
Allows remote entry of commands on the VEM from the Cisco Nexus 1000V. |
show monitor
To display the status of the Switched Port Analyzer (SPAN) sessions, use the show monitor command.
show monitor
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the status of the SPAN sessions:
n1000v# show monitor
Session State Reason Description
------- ----------- ---------------------- --------------------------------
17 down Session admin shut folio
Related Commands
show monitor session
To display the Switched Port Analyzer (SPAN) session configuration, use the show monitor session command.
show monitor session {session_number | all | range {session_range}} [brief]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the SPAN session configuration for session 1:
n1000v(config)# show monitor session 1
session 1
---------------
type : erspan-source
state : up
source intf :
rx : Eth3/3
tx : Eth3/3
both : Eth3/3
source VLANs :
rx :
tx :
both :
filter VLANs : filter not specified
destination IP : 10.54.54.1
ERSPAN ID : 999
ERSPAN TTL : 64
ERSPAN IP Prec. : 0
ERSPAN DSCP : 0
ERSPAN MTU : 1000
Related Commands
show ntp peer-status
To display the status for all Network Time Protocol (NTP) servers and peers, use the show ntp peer-status command.
show ntp peer-status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
A domain name is resolved only when you have a DNS server configured.
Examples
This example shows how to display the configured server and peers:
n1000v# show ntp peer-status
Total peers : 2
* - selected for sync, + - peer mode(active),
- - peer mode(passive), = - polled in client mode
remote local st poll reach delay vrf
------------------------------------------------------------------------
=192.0.2.10 0.0.0.0 16 16 0 0.00000 default
+72.229.253.127 0.0.0.0 16 16 0 0.00000 default
n1000v#
Related Commands
|
|
|
|---|---|
show ntp peers |
Displays all NTP peers. |
show ntp statistics |
Displays NTP statistics. |
ntp server |
Forms an association with a server. |
ntp peer |
Forms an association with a peer. |
show ntp peers
To display all Network Time Protocol (NTP) peers, use the show ntp peers command.
show ntp peers
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
A domain name is resolved only when you have a DNS server configured.
Examples
This example shows how to display the configured server and peers:
n1000v# show ntp peers
--------------------------------------------------
Peer IP Address Serv/Peer
--------------------------------------------------
192.0.2.10 Server (configured)
72.229.253.127 Peer (configured)
n1000v#
Related Commands
show ntp statistics
To display Network Time Protocol (NTP) statistics, use the show ntp statistics command.
show ntp statistics {io | local | memory | peer {ip-address | dns-name}}
Syntax Description
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
A domain name is resolved only when you have a DNS server configured.
Examples
This example shows how to display the configured server and peers:
n1000v# show ntp statistics local
system uptime: 6742265
time since reset: 6742265
old version packets: 0
old version packets: 0
unknown version number: 0
bad packet format: 0
packets processed: 0
bad authentication: 0
packets rejected: 0
n1000v#
Related Commands
|
|
|
|---|---|
ntp server |
Forms an association with a server. |
ntp peer |
Forms an association with a peer. |
show password strength-check
To display whether password strength is being checked, use the show password strength-check command.
show password strength-check
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display whether password strength is being checked:
n1000v# show password strength-check
Password strength check enabled
n1000v#
Related Commands
|
|
|
|---|---|
password strength-check |
Enables password-strength checking. |
username |
Creates a user account. |
role name |
Names a user role and puts you in role configuration mode for that role. |
show policy-map
To display the policy map configuration for all policy maps or for a specified policy map, use the show policy-map command.
show policy-map [type qos] [policy_map_name]
Syntax Description
type |
(Optional) Specifies the type of the policy map. |
qos |
(Optional) Specifies type QoS. |
policy_map_ |
(Optional) Name of an existing policy map. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the policy map configuration for all policy maps:
n1000v# show policy-map
Type qos policy-maps
====================
policy-map type qos class1
class class-default
policy-map type qos policy1
class class1
set dscp 26
class class2
set dscp 14
class class-default
set dscp 20
police cir 256000 bps bc 300 ms pir 256000 bps be 300 ms conform transmit
exceed set dscp dscp table cir-markdown-map violate drop
policy-map type qos policy2
policy-map type qos policy3
class class-default
police cir 256000 bps bc 300 ms pir 256000 bps be 300 ms conform transmit
exceed set dscp dscp table cir-markdown-map violate drop
n1000v#
Related Commands
show policy-map interface
To display the status of the global statistics and the configured policy maps on all interfaces, use the show policy-map interface command.
show policy-map interface [brief] [ethernet slot/port | port-channel port_channel_number | vethernet interface_number] [[input | output] [type qos]]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display statistics for policy maps that are configured on interfaces:
n1000v(config)# show policy-map interface
Global statistics status : enabled
Vethernet3
Service-policy (qos) input: new-policy
policy statistics status: enabled
Class-map (qos): class-default (match-any)
59610700 packets
set prec 5
Vethernet5
Service-policy (qos) output: new-policer
policy statistics status: enabled
Class-map (qos): new-class (match-all)
344661013 packets
Match: precedence 5
police cir 900 mbps bc 200 ms
conformed 505953339796 bytes, 899924196 bps action: transmit
violated 12285218014 bytes, 22283000 bps action: dropn1000v#
Related Commands
show port-channel compatibility-parameters
To display the parameters that must be the same among the member ports in order to join a port channel, use the show port-channel compatibility parameters command.
show port-channel compatibility-parameters
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
When you add an interface to a channel group, the software checks certain interface attributes to ensure that the interface is compatible with the channel group. For example, you cannot add a Layer 3 interface to a Layer 2 channel group. The software also checks a number of operational attributes for an interface before allowing that interface to participate in the port-channel aggregation.
This command displays the list of compatibility checks that the system uses.
Using the channel-group command, you can force ports with incompatible parameters to join the port channel as long as the following parameters are the same:
•(Link) speed capability
•Speed configuration
•Duplex capability
•Duplex configuration
•Flow-control capability
•Flow-control configuration
Note See the channel-group command for information about forcing ports to join a port channel.
Examples
This example shows how to display the list of compatibility checks that the system makes before an interface to a channel group:
n1000v# show port-channel compatibility-parameters
* port mode
Members must have the same port mode configured, either E or AUTO. If they
are configured in AUTO port mode, they have to negotiate E mode when they
come up. If a member negotiates a different mode, it will be suspended.
* speed
Members must have the same speed configured. If they are configured in AUTO
speed, they have to negotiate the same speed when they come up. If a member
negotiates a different speed, it will be suspended.
* MTU
Members have to have the same MTU configured. This only applies to ethernet
port-channel.
* MEDIUM
Members have to have the same medium type configured. This only applies to
ethernet port-channel.
* Span mode
Members must have the same span mode.
* sub interfaces
Members must not have sub-interfaces.
* Duplex Mode
Members must have same Duplex Mode configured.
* Ethernet Layer
Members must have same Ethernet Layer (switchport/no-switchport) configured.
* Span Port
Members cannot be SPAN ports.
* Storm Control
Members must have same storm-control configured.
* Flow Control
Members must have same flowctrl configured.
* Capabilities
Members must have common capabilities.
* port
Members port VLAN info.
* port
Members port does not exist.
* switching port
Members must be switching port, Layer 2.
* port access VLAN
Members must have the same port access VLAN.
* port native VLAN
Members must have the same port native VLAN.
* port allowed VLAN list
Members must have the same port allowed VLAN list.
Related Commands
|
|
|
|---|---|
channel-group |
Adds or removes interfaces to port-channel groups and assigns the port-channel mode to the interface. |
show port-channel database
To display information about the current running of the port channels, use the show port-channel database command.
show port-channel database [interface port-channel channel-number]
Syntax Description
channel-number |
Port-channel number for the information that you want to display. The range of values is from 1 to 4096. |
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
If you do not specify the channel-number, all channel groups are displayed. This command displays Link Aggregation Control Protocol (LACP)-enabled ports channels and port channels without an associated aggregation protocol.
Examples
This example shows how to display information on the current running of all port channels:
n1000v# show port-channel database
port-channel5
Administrative channel mode is active
Operational channel mode is active
Last membership update is successful
1 ports in total, 0 ports up
Age of the port-channel is 1d:16h:18m:50s
Time since last bundle is 1d:16h:18m:56s
Last bundled member is
Ports: Ethernet2/5 [down]
port-channel20
Administrative channel mode is active
Operational channel mode is active
Last membership update is successful
1 ports in total, 0 ports up
Age of the port-channel is 1d:16h:18m:50s
Time since last bundle is 1d:16h:18m:56s
Last bundled member is
Ports: Ethernet2/20 [down]
This example shows how to display information on the current running of a specific port channel:
n1000v# show port-channel database interface port-channel 20
port-channel20
Administrative channel mode is active
Operational channel mode is active
Last membership update is successful
1 ports in total, 0 ports up
Age of the port-channel is 1d:16h:23m:14s
Time since last bundle is 1d:16h:23m:20s
Last bundled member is
Ports: Ethernet2/20 [down]
Related Commands
|
|
|
|---|---|
show port-channel summary |
Displays a summary of information about all port channels. |
show port-channel load-balance
To display information about load-balancing using port channels, use the show port-channel load-balance command.
show port-channel load-balance [forwarding-path interface port-channel channel-number]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display information about the current port-channel load balancing for the system:
n1000v# show port-channel load-balance
Port Channel Load-Balancing Configuration:
System: source-dest-ip-vlan
Port Channel Load-Balancing Addresses Used Per-Protocol:
Non-IP: source-dest-mac
IP: source-dest-ip-vlan
Related Commands
|
|
|
|---|---|
port-channel load-balance ethernet |
Configures load balancing using port channels. |
show port-channel rbh-distribution
To display information about the Result Bundle Hash (RBH) for port channels, use the show port-channel rbh-distribution command.
show port-channel rbh-distribution [interface port-channel channel-number]
Syntax Description
channel-number |
Port-channel number for the information the you want to display. The range of values is from 1 to 4096. |
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
The RBH value ranges from 0 to 7 and is shared among port members in a port channel.
Examples
This example shows how to display RBH distribution for a specific port channel:
n1000v# show port-channel rbh-distribution interface port-channel 4
ChanId Member port RBH values Num of buckets
-------- ------------- ----------------- ----------------
4 Eth3/13 4,5,6,7 4
4 Eth3/14 0,1,2,3 4
Related Commands
|
|
|
|---|---|
port-channel summary |
Displays summary information on port channels. |
show port-channel summary
To display summary information about the port channels, use the show port-channel summary command.
show port-channel summary
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
If the Link Aggregation Control Protocol (LACP) is not enabled, the output shows NONE in the Protocol column of the display.
A channel-group interface can be in the following operational states:
•Down—The interface is down because it is administratively shut down or some other reason not related to port channels.
•Individual—The interface is part of a port channel but unable to aggregate into a port channel because of protocol exchange problems.
–This interface continues to forward traffic as an individual link.
–STP is aware of this interface.
•Suspended—The operational parameters of the interface are not compatible with the port channel. This interface is not forwarding traffic, although the physical MAC link state is still up.
•Switched—The interface is switched.
•Up (port channel)—The port channel is up.
•Up in port channel (members)—The port member of the port channel is up.
•Hot standby (LACP only)—The interface is eligible to join the port group if one of the interfaces currently participating in the LACP channel goes down.
–This interface does not forward data traffic, only protocol data units (PDUs).
–This interface does not run STP.
•Module-removed—The module has been removed.
•Routed—The interface is routed.
Examples
This example shows how to display summary information for the port channels:
n1000v# show port-channel summary
Flags: D - Down P - Up in port-channel (members)
I - Individual H - Hot-standby (LACP only)
s - Suspended r - Module-removed
S - Switched R - Routed
U - Up (port-channel)
-------------------------------------------------------------------
Group Port- Type Protocol Member Ports
Channel
-------------------------------------------------------------------
5 Po5(SD) Eth LACP Eth2/5(D)
20 Po20(RD) Eth LACP Eth2/20(D)
Related Commands
show port-channel traffic
To display traffic statistics for port channels, use the show port-channel traffic command.
show port-channel traffic [interface port-channel channel-number]
Syntax Description
channel-number |
Port-channel number for the traffic statistics that you want to display. The range of values is from 1 to 4096. |
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
This command displays the percentage of transmitted and received unicast, multicast, and broadcast traffic on the port channel.
If you do not specify the channel-number, information for all port channels is displayed.
Examples
This example shows how to display the traffic statistics for all port channels:
n1000v(config)# show port-channel traffic
ChanId Port Rx-Ucst Tx-Ucst Rx-Mcst Tx-Mcst Rx-Bcst Tx-Bcst
------ --------- ------- ------- ------- ------- ------- -------
5 Eth2/5 0.0% 0.0% 0.0% 0.0% 0.0% 0.0%
------ --------- ------- ------- ------- ------- ------- -------
20 Eth2/20 0.0% 0.0% 0.0% 0.0% 0.0% 0.0%
This example shows how to display the traffic statistics for a specific port channel:
n1000v(config)# show port-channel traffic interface port-channel 5
ChanId Port Rx-Ucst Tx-Ucst Rx-Mcst Tx-Mcst Rx-Bcst Tx-Bcst
------ --------- ------- ------- ------- ------- ------- -------
5 Eth2/5 0.0% 0.0% 0.0% 0.0% 0.0% 0.0%
Related Commands
|
|
|
|---|---|
port-channel summary |
Displays summary information about port channels. |
show port-channel usage
To display the port-channel numbers used and available, use the show port-channel usage command.
show port-channel usage
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the usage for all port channels:
n1000v# show port-channel usage
Totally 2 port-channel numbers used
====================================
Used : 5 , 20
Unused: 1 - 4 , 6 - 19 , 21 - 4096
n1000v#
Related Commands
|
|
|
|---|---|
port-channel summary |
Displays summary information about port channels. |
show port-profile
To display configurations for port profiles, use the show port-profile command.
show port-profile [name prof_name]
Syntax Description
name |
(Optional) Specifies to display information about a specific port profile. |
prof_name |
Name of the port profile to display. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
Examples
The following example shows how to display the configuration of port profile UplinkProfile1:
n1000v(config-port-prof)# show port-profile name UplinkProfile1
port-profile UplinkProfile1
description: "Profile for critical system ports"
type: ethernet
status: disabled
capability l3control: no
pinning control-vlan: -
pinning packet-vlan: -
system vlans: none
port-group: UplinkProfile1
max ports: -
inherit:
config attributes:
switchport mode access
switchport access vlan 113
switchport trunk native vlan 113
channel-group auto mode on
no shutdown
evaluated config attributes:
switchport mode access
switchport access vlan 113
switchport trunk native vlan 113
channel-group auto mode on
no shutdown
assigned interfaces:
n1000v(config-port-prof)#
Related Commands
|
|
|
|---|---|
show running-config port-profile |
Displays the running configurations of port profiles. |
show port-profile expand-interface
To verify that the interface level configuration did not overwrite the port profile configuration, use the show port-profile expand-interface command.
show port-profile expand-interface [name port-profile-name]
Syntax Description
name |
(Optional) Limits the display to a particular port profile name. |
module-number |
Name that identifies an existing port profile. |
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to verify that the interface level configuration did not overwrite the port profile configuration:
n1000v# show port-profile expand-interface
port-profile 1
port-profile 2
port-profile AccessProf
port-profile AccessProfile
port-profile AccessProfile1
port-profile AllAccess
port-profile AllAccess1
port-profile AllAccess2
port-profile PortProfile1
port-profile Profile1
port-profile SystemProfile
n1000v#
Related Commands
show port-security
To display the secured MAC addresses in the system, use the show port-security command.
show port-security
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the secured MAC addresses in the system:
n1000V# show port-security
Total Secured Mac Addresses in System (excluding one mac per port) : 0
Max Addresses limit in System (excluding one mac per port) : 8192
----------------------------------------------------------------------------
Secure Port MaxSecureAddr CurrentAddr SecurityViolation Security Action
(Count) (Count) (Count)
----------------------------------------------------------------------------
Vethernet1 1 0 0 Shutdown
==========================================================================
Related Commands
show port-security address
To display information about all secure MAC-addresses in the system, use the show port-security address command.
show port-security address interface-id
Syntax Description
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
Examples
This example shows how to use the show port-security address command to view information about all MAC addresses in the system:
switch# show port-security address
Total Secured Mac Addresses in System (excluding one mac per port) : 0
Max Addresses limit in System (excluding one mac per port) : 8192
----------------------------------------------------------------------
Secure Mac Address Table
----------------------------------------------------------------------
Vlan Mac Address Type Ports Remaining Age
(mins)
---- ----------- ------ ----- -------------
1 0054.AAB3.770F STATIC port-channel1 0
1 00EE.378A.ABCE STATIC Ethernet1/4 0
======================================================================
switch#
This example shows how to use the show port-security address command to view the MAC addresses secured by the port security feature on the Ethernet 1/4 interface:
switch# show port-security address interface ethernet 1/4
Secure Mac Address Table
----------------------------------------------------------------------
Vlan Mac Address Type Ports Remaining Age
(mins)
---- ----------- ------ ----- -------------
1 00EE.378A.ABCE STATIC Ethernet1/4 0
----------------------------------------------------------------------
switch#
This example shows how to use the show port-security address command to view the MAC addresses secured by the port security feature on the vethernet1 interface:
n1000v# show port-security address interface vethernet 1
Total Secured Mac Addresses in System (excluding one mac per port) : 0
Max Addresses limit in System (excluding one mac per port) : 8192
----------------------------------------------------------------------
Secure Mac Address Table
----------------------------------------------------------------------
Vlan Mac Address Type Ports Remaining age
(mins)
---- ----------- ------ ----- ---------------
65 0050.56B7.7DE2 DYNAMIC Vethernet1 0
=====================================================================
n1000v#
Related Commands
show port-security interface
To display information about the secure interfaces on the system, use the show port-security interface command.
show port-security interface interface-id
Syntax Description
interface-id |
Interface ID. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
Examples
This example shows how to use the show port-security interface command to view the status of the port security feature on the Ethernet 1/4 interface:
switch# show port-security interface ethernet 1/4
Port Security : Enabled
Port Status : Secure Down
Violation Mode : Shutdown
Aging Time : 0 mins
Aging Type : Absolute
Maximum MAC Addresses : 5
Total MAC Addresses : 1
Configured MAC Addresses : 1
Sticky MAC Addresses : 0
Security violation count : 0
switch#
Related Commands
show processes
To display the state and the start count of all processes, use the show processes command.
show processes [cpu | log | memory]
Syntax Description
cpu |
(Optional) Specifies processes related to the CPU. |
log |
(Optional) Specifies information regarding process logs. |
memory |
(Optional) Specifies processes related to memory. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the state and the start count of all processe:
n1000v# show processes
PID State PC Start_cnt TTY Type Process
----- ----- -------- ----------- ---- ---- -------------
1 S 77f8a468 1 - O init
2 S 0 1 - O ksoftirqd/0
3 S 0 1 - O desched/0
4 S 0 1 - O events/0
5 S 0 1 - O khelper
10 S 0 1 - O kthread
18 S 0 1 - O kblockd/0
35 S 0 1 - O khubd
121 S 0 1 - O pdflush
122 S 0 1 - O pdflush
124 S 0 1 - O aio/0
123 S 0 1 - O kswapd0
709 S 0 1 - O kseriod
756 S 0 1 - O kide/0
766 S 0 1 - O ata/0
770 S 0 1 - O scsi_eh_0
1096 S 0 1 - O kjournald
1101 S 0 1 - O kjournald
1620 S 0 1 - O kjournald
1627 S 0 1 - O kjournald
1952 S 77f6c18e 1 - O portmap
1965 S 0 1 - O nfsd
1966 S 0 1 - O nfsd
1967 S 0 1 - O nfsd
1968 S 0 1 - O nfsd
1969 S 0 1 - O nfsd
1970 S 0 1 - O nfsd
1971 S 0 1 - O nfsd
1972 S 0 1 - O nfsd
1973 S 0 1 - O lockd
1974 S 0 1 - O rpciod
1979 S 77f6e468 1 - O rpc.mountd
1989 S 77f6e468 1 - O rpc.statd
2016 S 77e0e468 1 - VG sysmgr
2298 S 0 1 - O mping-thread
2299 S 0 1 - O mping-thread
2315 S 0 1 - O stun_kthread
2316 S 0 1 - O stun_arp_mts_kt
2339 S 0 1 - O redun_kthread
2340 S 0 1 - O redun_timer_kth
2866 S 0 1 - O sf_rdn_kthread
2866 S 0 1 - O sf_rdn_kthread
2867 S 77f37468 1 - VU xinetd
2868 S 77f6e468 1 - VU tftpd
2869 S 7788c1b6 1 - VL syslogd
2870 S 77ecf468 1 - VU sdwrapd
2872 S 77d94468 1 - VU platform
2877 S 0 1 - O ls-notify-mts-t
2889 S 77eb2be4 1 - VU pfm_dummy
2896 S 77f836be 1 - O klogd
2903 S 77d9ebe4 1 - VL vshd
2904 S 77e41468 1 - VU stun
2905 S 77a74f43 1 - VL smm
2906 S 77e5a468 1 - VL session-mgr
2907 S 77c4e468 1 - VL psshelper
2908 S 77f75468 1 - VU lmgrd
2909 S 77e36be4 1 - VG licmgr
2910 S 77ebe468 1 - VG fs-daemon
2911 S 77ec5468 1 - VL feature-mgr
2912 S 77e7a468 1 - VU confcheck
2913 S 77eb3468 1 - VU capability
2915 S 77c4e468 1 - VU psshelper_gsvc
2922 S 77f75468 1 - O cisco
2937 S 77895f43 1 - VL clis
2937 S 77895f43 1 - VL clis
2952 S 77cba468 1 - VL xmlma
2953 S 77e8b468 1 - VL vmm
2955 S 77e80468 1 - VU ttyd
2957 S 77ecb6be 1 - VL sysinfo
2958 S 77b57468 1 - VL sksd
2959 S 77ea7468 1 - VG res_mgr
2960 S 77e53468 1 - VG plugin
2961 S 77ccf468 1 - VL mvsh
2962 S 77e05468 1 - VU module
2963 S 77cce468 1 - VL evms
2964 S 77ccf468 1 - VL evmc
2965 S 77ecc468 1 - VU core-dmon
2966 S 7765b40d 1 - VL ascii-cfg
2967 S 77cebbe4 1 - VL securityd
2968 S 77cb5468 1 - VU cert_enroll
2969 S 77b17be4 1 - VL aaa
2973 S 77e19468 1 - VU ExceptionLog
2975 S 77dfb468 1 - VU bootvar
2976 S 77df9468 1 - VG ifmgr
2977 S 77ead468 1 - VU tcap
2978 S 77a6bf43 1 - VL l3vm
2978 S 77a6bf43 1 - VL l3vm
2979 S 77a62f43 1 - VL u6rib
2980 S 77a62f43 1 - VL urib
2981 S 77f30be4 1 - VU core-client
2983 S 77b95468 1 - VL aclmgr
3008 S 77d51468 1 - VU aclcomp
3011 S 7774440d 1 - VL tacacs
3012 S 77a72f43 1 - VL adjmgr
3016 S 77a74f43 1 - VL arp
3021 S 778a1896 1 - VL icmpv6
3022 S 7791ef43 1 - VL netstack
3050 S 7770240d 1 - VL radius
3051 S 77f59be4 1 - VL ip_dummy
3052 S 77f59be4 1 - VL ipv6_dummy
3053 S 7783c40d 1 - VU ntp
3054 S 77f59be4 1 - VL pktmgr_dummy
3055 S 778ae40d 1 - VL snmpd
3056 S 77f59be4 1 - VL tcpudp_dummy
3063 S 7782d40d 1 - VL cdp
3064 S 77b1540d 1 - VL dcos-xinetd
3154 S 77b4040d 1 - O ntpd
3195 S 77e0d468 1 - VL vsim
3196 S 778ee40d 1 - VL ufdm
3196 S 778ee40d 1 - VL ufdm
3197 S 77d42468 1 - VU sf_nf_srv
3198 S 778e240d 1 - VL sal
3199 S 77a14f43 1 - VL rpm
3200 S 778cd40d 1 - VG pltfm_config
3201 S 77efc468 1 - VU pixmc
3202 S 77e0f468 1 - VG pixm
3203 S 77c43468 1 - VU pdl_srv_tst
3204 S 7789e40d 1 - VL nfm
3205 S 77ddc468 1 - VU msp
3206 S 77dbc468 1 - VL monitor
3207 S 7789c40d 1 - VL mfdm
3208 S 7787340d 1 - VL l2fm
3209 S 77dc0468 1 - VL ipqosmgr
3210 S 77e81468 1 - VU ethanalyzer
3211 S 777b740d 1 - VL dhcp_snoop
3212 S 77b3940d 1 - VL dcos-thttpd
3213 S 77c26468 1 - VU copp
3214 S 77b2b468 1 - VL eth_port_channel
3215 S 77d15468 1 - VL vlan_mgr
3219 S 758bc40d 1 - VU vms
3220 S 77b8a468 1 - VL eth-port-sec
3221 S 77abb468 1 - VL stp
3221 S 77abb468 1 - VL stp
3226 S 77de5468 1 - VL lacp
3228 S 777ba40d 1 - VL ethpm
3232 S 77a0127b 1 - VL igmp
3235 S 77dba468 1 - VL private-vlan
3241 S 77d70468 1 - VU vim
3246 S 77d4b468 1 - VU portprofile
3285 S 77f836be 1 1 O getty
3286 S 77f806be 1 S0 O getty
3290 S 77f1deee 1 - O gettylogin1
3308 S 77f836be 1 S1 O getty
3360 S 77ae140d 1 - O dcos_sshd
3361 S 77aaa468 1 8 O vsh
4213 Z 0 1 - O vmw_maintenance
25188 Z 0 1 - O vmw_maintenance
31228 Z 0 1 - O vmw_maintenance
427 Z 0 1 - O vmw_maintenance
1035 Z 0 1 - O vmw_maintenance
2439 Z 0 1 - O vmw_maintenance
7167 Z 0 1 - O vmw_maintenance
8246 Z 0 1 - O vmw_maintenance
8856 Z 0 1 - O vmw_maintenance
10539 Z 0 1 - O vmw_maintenance
10539 Z 0 1 - O vmw_maintenance
16083 Z 0 1 - O vmw_maintenance
19353 S 77ae140d 1 - O dcos_sshd
19354 S 7752340d 1 - O xmlsa
13167 S 77ae140d 1 - O dcos_sshd
13169 S 77aaa468 1 17 O vsh
14253 S 7798140d 1 - O in.dcos-telnetd
14254 S 77aaa468 1 18 O vsh
14757 S 7798140d 1 - O in.dcos-telnetd
14758 S 77a82eee 1 19 O vsh
14933 S 77f426be 1 19 O more
14934 S 77aa9be4 1 19 O vsh
14935 R 77f716be 1 - O ps
- NR - 0 - VL eigrp
- NR - 0 - VL isis
- NR - 0 - VL ospf
- NR - 0 - VL ospfv3
- NR - 0 - VL rip
- NR - 0 - VL eigrp
- NR - 0 - VL isis
- NR - 0 - VL ospf
- NR - 0 - VL ospfv3
- NR - 0 - VL rip
- NR - 0 - VL rip
- NR - 0 - VL eigrp
- NR - 0 - VL isis
- NR - 0 - VL ospf
- NR - 0 - VL ospfv3
- NR - 0 - VL rip
- NR - 0 - VL eigrp
- NR - 0 - VL isis
- NR - 0 - VL ospf
- NR - 0 - VL ospfv3
- NR - 0 - VL rip
- NR - 0 - VL amt
- NR - 0 - VL bgp
- NR - 0 - VL eou
- NR - 0 - VL glbp
- NR - 0 - VL hsrp_engine
- NR - 0 - VU installer
- NR - 0 - VL interface-vlan
- NR - 0 - VU lisp
- NR - 0 - VL msdp
- NR - 0 - VL pim
- NR - 0 - VL pim6
- NR - 0 - VL scheduler
- NR - 0 - VL isis
- NR - 0 - VL ospf
- NR - 0 - VL ospfv3
- NR - 0 - VL rip
- NR - 0 - VL amt
- NR - 0 - VL bgp
- NR - 0 - VL eou
- NR - 0 - VL glbp
- NR - 0 - VL hsrp_engine
- NR - 0 - VU installer
- NR - 0 - VL interface-vlan
- NR - 0 - VU lisp
- NR - 0 - VL msdp
- NR - 0 - VL pim
- NR - 0 - VL pim6
- NR - 0 - VL scheduler
- NR - 0 - VU vbuilder
State: R(runnable), S(sleeping), Z(defunct)
Type: U(unknown), O(non sysmgr)
NR(not running), ER(terminated etc)
n1000v#
Related Commands
show radius-server
To display the RADIUS server configuration, use the show radius-server command.
show radius-server [host]
Syntax Description
host |
(Optional) DNS name or IP address for the RADIUS server. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the RADIUS server configuration:
n1000v# show radius-server ads
ads:
available for authentication on port:1812
available for accounting on port:1813
idle time:0
test user:test
test password:********
n1000v(config)#
Related Commands
show radius-server directed-request
To display the directed request configuration, use the show radius-server directed-request command.
show radius-server directed-request
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the directed request configuration:
n1000v(config)# show radius-server directed-request
disabled
n1000v(config)#
Related Commands
show radius-server groups
To display information about the RADIUS server group configuration, use the show radius-server groups command.
show radius-server groups [group-name]
Syntax Description
group-name |
(Optional) Name of the RADIUS server group. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display information about the RADIUS server group configuration:
n1000v# show radius-server groups
n1000v#
Related Commands
show radius-server sorted
To display the RADIUS server configuration in a sorted format, use the show radius-server sorted command.
show radius-server sorted
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the RADIUS server configuration in a sorted format:
n1000v(config)#show radius-server sorted
Related Commands
show radius-server statistics
To displays the RADIUS statistics, use the show radius-server statistics command.
show radius-server statistics {hostname | ipv4-address}
Syntax Description
hostname |
DNS name for the RADIUS server host. |
ipv4-address |
IP address of the RADIUS server host. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the RADIUS statistics:
n1000v# show radius-server statistics 10.10.1.1
Server is not monitored
Authentication Statistics
failed transactions: 0
sucessfull transactions: 0
requests sent: 0
requests timed out: 0
responses with no matching requests: 0
responses not processed: 0
responses containing errors: 0
Accounting Statistics
failed transactions: 0
sucessfull transactions: 0
requests sent: 0
requests timed out: 0
responses with no matching requests: 0
responses not processed: 0
responses containing errors: 0
Related Commands
show running-config diff
To verify the difference between the running and startup configurations, use the show running-config diff command.
show running-config diff
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
When you switch over from one VSM to another, any unsaved running configuration that was available in an active VSM is still unsaved in the new active VSM. You can verify this unsaved running configuration with this command. Then, save that configuration in the startup. if needed.
Examples
This example shows how to verify the difference between the running and startup configurations:
n1000v# show running-config diff
*** Startup-config
--- Running-config
***************
*** 1,38 ****
version 4.0(4)SV1(1)
role feature-group name new
role name testrole
username admin password 5 $1$S7HvKc5G$aguYqHl0dPttBJAhEPwsy1 role network-admin
telnet server enable
ip domain-lookup
Related Commands
show running-config interface ethernet
To display the running configuration for a specific Ethernet interface, use the show running-config interface ethernet command.
show running-config interface ethernet slot/port
Syntax Description
slot/port |
Slot number and port number for an existing Ethernet interface. |
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the running configuration for a Ethernet interface 2/1:
n1000v# show running-config interface ethernet 2/1
version 4.0(4)SV1(3)
interface Ethernet3/2
inherit port-profile uplink_all
Related Commands
show running-config interface port-channel
To display the running configuration for a specific port channel, use the show running-config interface port-channel command.
show running-config interface port-channel {channel-number}
Syntax Description
channel-number |
Number of the port-channel group. The range of values is from 1 to 4096. |
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
|---|---|
4.0(4)SV1(1) |
This command was introduced. |
Examples
The following example shows how to display the running configuration for port channel 10:
n1000v(config)# show running-config interface port-channel 10
version 4.0(4)SV1(1)
interface port-channel10
switchport
switchport mode trunk
Related Commands
|
|
|
|---|---|
show port-channel summary |
Displays a summary of port-channel information. |
show running-config port-profile
To display the running configuration of port profiles, use the show running-config port-profile command.
show running-config port-profile [prof_name]
Syntax Description
prof_name |
(Optional) Port profile name. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(2) |
This command was introduced. |
Examples
The following example shows how to display the running configuration for all port profiles on the switch:
n1000v# show running-config port-profile
port-profile type ethernet UplinkProfile1
description "Profile for critical system ports"
vmware port-group
switchport mode access
switchport access vlan 113
switchport trunk native vlan 113
channel-group auto mode on
no shutdown
port-profile type vethernet VethProfile
vmware port-group
vmware max-ports 5
switchport mode trunk
switchport trunk native vlan 112
no shutdown
n1000v#
Related Commands
|
|
|
|---|---|
show port-profile |
Displays configurations for port profiles. |
show running-config interface vethernet
To display the running configuration for a specific vEthernet interface, use the show running-config interface vethernet command.
show running-config interface vethernet interface-number
Syntax Description
interface-number |
Number that identifies an existing vEthernet interface. |
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the running configuration for a vEthernet interface 2/1:
n1000v# show running-config interface vethernet 1
version 4.0(4)SV1(2)
interface Vethernet1
description isp_pvlan1
pinning id 3
switchport mode private-vlan host
no shutdown
n1000v#
Related Commands
show running-config vlan
To display the running configuration for a specified VLAN, use the show running-config vlan command.
show running-config vlan vlan-id
Syntax Description
vlan-id |
VLAN ID number or range of VLANs. Valid VLAN IDs are1-4094 or ranges are 1-5, 10 or 2-5, 7-19. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
Examples
This example shows how display the running configuration for VLAN100:
n1000v(config)#show running-config vlan 100
version 4.2(1)SV1(4)
vlan 100
n1000v(config)#
Related Commands
|
|
|
|---|---|
show vlan |
Displays VLAN information. |
vlan |
Creates a VLAN. |
show radius-server directed-request
To display the directed request configuration, use the show radius-server directed-request command.
show radius-server directed-request
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the directed request configuration:
n1000v(config)# show radius-server directed-request
disabled
n1000v(config)#
Related Commands
show snmp
To display information about one or more destination profiles, use the show snmp command.
show snmp [community | context | engineID | group | host | sessions | trap | user]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display information about the SNMP engineID:
n1000v# show snmp engineID
Local SNMP engineID: [Hex] 800000090302000C000000
[Dec] 128:000:000:009:003:002:000:012:000:000:000
n1000v#
Related Commands
|
|
|
|---|---|
snmp-server contact |
Configures sysContact, which is the SNMP contact name. |
snmp-server location |
Configures sysLocation, which is the SNMP location. |
show ssh key
To display the Secure Shell (SSH) server keys, use the show ssh key command.
show ssh key [dsa | rsa]
Syntax Description
dsa |
(Optional) Specifies the display of DSA SSH keys. |
rsa |
(Optional) Specifies the display of RSA SSH keys. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display SSH server keys:
n1000v# show ssh key
n1000v#
Related Commands
|
|
|
|---|---|
ssh key |
Generates the SSH server key. |
show ssh server |
Displays whether the SSH server is enabled. |
show ssh server
To display the Secure Shell (SSH) server configuration, use the show ssh server command.
show ssh server
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the SSH server configuration:
n1000v# show ssh server
ssh is enabled
version 2 enabled
n1000v#
Related Commands
show startup-config aaa
To display the Authentication, Authorization and Accounting protocol (AAA) configuration in the startup configuration, use the show startup-config aaa command.
show startup-config aaa
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the AAA configuration in the startup configuration:
n1000v# show startup-config aaa
version 4.0(4)SV1(2)
n1000v#
Related Commands
show startup-config radius
To display the RADIUS configuration in the startup configuration, use the show startup-config radius command.
show startup-config radius
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the RADIUS configuration in the startup configuration:
n1000v# show startup-config radius
version 4.0(4)SV1(2)
n1000v#
Related Commands
show startup-config security
To dsplay the user account configuration in the startup configuration, use the show startup-config security command.
show startup-config security
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the user account configuration in the startup configuration:
n1000v# show startup-config security
version 4.0(4)SV1(2)
username admin password 5 $1$3/cH7rWm$W3QUjfQOyfySds5p3/PtX. role network-admin
username kathleen password 5 $1$7vewiaFA$iLCfmalyKeSBySqrAgvNZ/ role network-op
erator
username kathleen role network-admin
telnet server enable
n1000v#
Related Commands
show svs connections
To display the current connections to the Cisco Nexus 1000V for verification, use the show svs connections command.
show svs connections [conn_name]
Syntax Description
conn_name |
(Optional) Name of an existing connection. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display information about the SVS connection:
n1000v# show svs connections
connection vc:
hostname: 172.23.232.139
remote port: 80
protocol: vmware-vim https
certificate: default
datacenter name: Documentation-DC
DVS uuid: 9b dd 36 50 2e 27 27 8b-07 ed 81 89 ef 43 31 17
config status: Enabled
operational status: Disconnected
sync status: -
version: -
n1000v#
Related Commands
show svs domain
To display the VSM domain configuration, use the show svs domain command.
show svs domain
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
4.0(4)SV1(2) |
The output of this command was modified to include the Layer 2 and Layer 3 transport mode configuration. |
Examples
This example shows how to display the VSM domain configuration:
n1000v# config t
n1000v(config)# svs-domain
n1000v(config-svs-domain)# show svs domain
SVS domain config:
Domain id: 100
Control vlan: 100
Packet vlan: 101
Management vlan: 0
L2/L3 Control mode: L3
L2/L3 Control interface: mgmt0
Status: Config push to VC successful.
n1000v(config-svs-domain)#
Related Commands
|
|
|
|---|---|
svs-domain |
Creates and configures a domain for the Cisco Nexus 1000V that identifies the VSM and VEMs and the control and packet VLANs for communication and management. |
show svs neighbors
To display all SVS neighbors, use the show svs neighbors command.
show svs neighbors
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display all SVS neighbors:
n1000v# show svs neighbors
Active Domain ID: 113
AIPC Interface MAC: 0050-56b6-2bd3
Inband Interface MAC: 0050-56b6-4f2d
Src MAC Type Domain-id Node-id Last learnt (Sec. ago)
------------------------------------------------------------------------
0002-3d40-7102 VEM 113 0302 71441.12
0002-3d40-7103 VEM 113 0402 390.77
n1000v#
Related Commands
show system error-id
To display detailed information on system error codes, use the show system error-id command.
show system error-id {list | error-code}
Syntax Description
list |
Displays brief information for all the system error messages. |
error-code |
Displays description about a specific error code. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
Examples
This example shows how to display detailed information about error code 0x401e0008:
n1000v# show system error-id 0x401e0008
Error Facility: sysmgr
Error Description: request was aborted, standby disk may be full
n1000v#
Related Commands
show system redundancy status
To display the current redundancy status for the Virtual Supervisor Module (VSM), use the show system redundancy status command.
show system redundancy status
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the current redundancy status for the VSM:
n1000v# show system redundancy status
Redundancy role
---------------
administrative: standalone
operational: standalone
Redundancy mode
---------------
administrative: HA
operational: None
This supervisor (sup-1)
-----------------------
Redundancy state: Active
Supervisor state: Active
Internal state: Active with no standby
Other supervisor (sup-2)
------------------------
Redundancy state: Not present
n1000v#
Related Commands
|
|
|
|---|---|
system redundancy role |
Designates the HA role of the VSM. |
show system resources |
Displays the system resources. |
show system resources
To display system-related CPU and memory statistics, use the show system resources command.
show system resources
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display system-related CPU and memory statistics:
n1000v# show system resources
Load average: 1 minute: 0.00 5 minutes: 0.00 15 minutes: 0.00
Processes : 261 total, 1 running
CPU states : 0.0% user, 0.0% kernel, 100.0% idle
Memory usage: 2075012K total, 946780K used, 1128232K free
66764K buffers, 475404K cache
n1000v#
Related Commands
show system vem feature level
To display the current software release supported, use the show system vem feature level command.
show system vem feature level
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(2) |
This command was introduced. |
Examples
This example shows how to display the current VEM feature level:
n1000v# show system vem feature level
current feature level: 4.0(4)SV1(2)
n1000v#
Related Commands
|
|
|
|---|---|
system update vem feature level |
Changes the software version supported on VEMs. |
show tacacs-server
To display the TACACS+ server configuration, use the show tacacs-server command.
show tacacs-server
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Usage Guidelines
The global shared key is saved in encrypted form in the running configuration. To display the key, use the show running-config command.
Examples
This example shows how to displays the TACACS+ server configuration:
n1000v# show tacacs-server
Global TACACS+ shared secret:********
timeout value:5
deadtime value:0
total number of servers:1
following TACACS+ servers are configured:
10.10.2.2:
available on port:49
Related Commands
show tcp client
To display information about the TCP client, use the show tcp client command.
show tcp client [pid pid] [detail]
Syntax Description
pid |
(Optional) Specifies information about the client process. |
pid |
ID for the specified client process. |
detail |
(Optional) Specifies socket details. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display information about the TCP client:
n1000v# show tcp client
Total number of clients: 12
Total number of cancels: 255372
client: syslogd, pid: 2962, sockets: 2
client: ntp, pid: 3148, sockets: 2
client: dcos-xinetd, pid: 3156, sockets: 2
client: snmpd, pid: 3150, sockets: 4
client: ntpd, pid: 3243, sockets: 3
client: dcos-thttpd, pid: 3305, sockets: 2
client: radiusd, pid: 3143, sockets: 2
client: vms, pid: 3318, sockets: 0
client: dcos_sshd, pid: 3491, sockets: 3
client: vsh, pid: 3494, sockets: 0
client: in.dcos-telnetd, pid: 25028, sockets: 3
client: vsh, pid: 25029, sockets: 0
Related Commands
|
|
|
|---|---|
show tcp connection |
Displays information about the TCP connection. |
show tcp statistics |
Displays TCP protocol statistics. |
show tcp connection
To display information about the connection, use the show tcp connection command.
show tcp connection [pid pid | tcp | udp | raw] [local {srcIP | srcIP6}] [foreign {dstIP | dstIP6}] [detail]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display detailed information about the connection:
n1000v# show tcp connection detail
Total number of tcp sockets: 8
Active connections (including servers)
Local host: * (22), Foreign host: * (0)
Protocol: tcp6, type: stream, ttl: 64, tos: 0, Id: 6
Options: none, state:
Receive buffer:
cc: 0, hiwat: 25300, lowat: 1, flags: none
Send buffer:
cc: 0, hiwat: 25300, lowat: 2048, flags:
Sequence number state:
iss: 0, snduna: 0, sndnxt: 0, sndwnd: 0
irs: 0, rcvnxt: 0, rcvwnd: 0, sndcwnd: 1012
Timing parameters:
srtt: 0 ms, rtt: 0 ms, rttv: 12000 ms, krtt: 3000 ms
rttmin: 1000 ms, mss: 1012, duration: 1390144100 ms
State: LISTEN
Flags: none
Context: management
Local host: * (23), Foreign host: * (0)
Protocol: tcp6, type: stream, ttl: 64, tos: 0, Id: 17
Options: none, state:
Receive buffer:
cc: 0, hiwat: 17204, lowat: 1, flags: none
Send buffer:
cc: 0, hiwat: 17204, lowat: 2048, flags:
Sequence number state:
iss: 0, snduna: 0, sndnxt: 0, sndwnd: 0
irs: 0, rcvnxt: 0, rcvwnd: 0, sndcwnd: 1012
Timing parameters:
srtt: 0 ms, rtt: 0 ms, rttv: 12000 ms, krtt: 3000 ms
rttmin: 1000 ms, mss: 1012, duration: 1390144100 ms
State: LISTEN
Flags: none
Context: management
Local host: * (80), Foreign host: * (0)
Protocol: tcp6, type: stream, ttl: 64, tos: 0, Id: 13
Options: none, state: none
Receive buffer:
cc: 0, hiwat: 16384, lowat: 1, flags: none
Send buffer:
cc: 0, hiwat: 16384, lowat: 2048, flags:
Sequence number state:
iss: 0, snduna: 0, sndnxt: 0, sndwnd: 0
irs: 0, rcvnxt: 0, rcvwnd: 0, sndcwnd: 1073725440
Timing parameters:
srtt: 0 ms, rtt: 0 ms, rttv: 12000 ms, krtt: 3000 ms
rttmin: 1000 ms, mss: 1024, duration: 1390144100 ms
State: LISTEN
Flags: none
Context: management
Local host: * (80), Foreign host: * (0)
Protocol: tcp, type: stream, ttl: 64, tos: 0, Id: 14
Options: none, state: none
Receive buffer:
cc: 0, hiwat: 16500, lowat: 1, flags: none
Send buffer:
cc: 0, hiwat: 16500, lowat: 2048, flags:
Sequence number state:
iss: 0, snduna: 0, sndnxt: 0, sndwnd: 0
irs: 0, rcvnxt: 0, rcvwnd: 0, sndcwnd: 500
Timing parameters:
srtt: 0 ms, rtt: 0 ms, rttv: 12000 ms, krtt: 3000 ms
rttmin: 1000 ms, mss: 500, duration: 1390144100 ms
State: LISTEN
Flags: none
Context: management
Local host: * (161), Foreign host: * (0)
Protocol: tcp, type: stream, ttl: 64, tos: 0, Id: 3
Options: none, state: none
Receive buffer:
cc: 0, hiwat: 16384, lowat: 1, flags: none
Send buffer:
cc: 0, hiwat: 16384, lowat: 2048, flags:
Sequence number state:
iss: 0, snduna: 0, sndnxt: 0, sndwnd: 0
irs: 0, rcvnxt: 0, rcvwnd: 0, sndcwnd: 512
Timing parameters:
srtt: 0 ms, rtt: 0 ms, rttv: 12000 ms, krtt: 3000 ms
rttmin: 1000 ms, mss: 512, duration: 1390144100 ms
State: LISTEN
Flags: none
Context: management
Local host: * (161), Foreign host: * (0)
Protocol: tcp6, type: stream, ttl: 64, tos: 0, Id: 5
Options: none, state: none
Receive buffer:
cc: 0, hiwat: 16384, lowat: 1, flags: none
Send buffer:
cc: 0, hiwat: 16384, lowat: 2048, flags:
Sequence number state:
iss: 0, snduna: 0, sndnxt: 0, sndwnd: 0
irs: 0, rcvnxt: 0, rcvwnd: 0, sndcwnd: 1073725440
Timing parameters:
srtt: 0 ms, rtt: 0 ms, rttv: 12000 ms, krtt: 3000 ms
rttmin: 1000 ms, mss: 1024, duration: 1390144100 ms
State: LISTEN
Flags: none
Context: management
Local host: 10.10.233.74 (22), Foreign host: 10.10.185.189 (48131)
Protocol: tcp, type: stream, ttl: 64, tos: 0, Id: 20
Options: none, state: none
Receive buffer:
cc: 0, hiwat: 17500, lowat: 1, flags: none
Send buffer:
cc: 0, hiwat: 17500, lowat: 2048, flags:
Sequence number state:
iss: 3575780911, snduna: 3576001996, sndnxt: 3576001996, sndwnd: 32767
irs: 905490047, rcvnxt: 905574926, rcvwnd: 17500, sndcwnd: 1953
Timing parameters:
srtt: 700 ms, rtt: 0 ms, rttv: 0 ms, krtt: 1000 ms
rttmin: 1000 ms, mss: 500, duration: 1390101600 ms
State: ESTABLISHED
Flags: none
Context: management
Local host: 10.10.233.74 (23), Foreign host: 10.10.22.107 (35030)
Protocol: tcp, type: stream, ttl: 64, tos: 0, Id: 18
Options: none, state: none
Receive buffer:
cc: 0, hiwat: 17500, lowat: 1, flags: none
Send buffer:
cc: 0, hiwat: 17500, lowat: 2048, flags:
Sequence number state:
iss: 3273730667, snduna: 3273793065, sndnxt: 3273793065, sndwnd: 32767
irs: 3760023047, rcvnxt: 3760024636, rcvwnd: 17500, sndcwnd: 25095
Timing parameters:
srtt: 700 ms, rtt: 0 ms, rttv: 0 ms, krtt: 1000 ms
rttmin: 1000 ms, mss: 500, duration: 467168700 ms
State: ESTABLISHED
Flags: none
Context: management
Total number of udp sockets: 11
Active connections (including servers)
Local host: * (123), Foreign host: * (0)
Protocol: udp6, type: dgram, ttl: 64, tos: 0, Id: 11
Options: none, state: none
Receive buffer:
cc: 0, hiwat: 42240, lowat: 1, flags: none
Send buffer:
cc: 0, hiwat: 9216, lowat: 2048, flags:
Context: management
Local host: * (123), Foreign host: * (0)
Protocol: udp, type: dgram, ttl: 64, tos: 0x10, Id: 10
Options: none, state: none
Receive buffer:
cc: 0, hiwat: 42240, lowat: 1, flags: none
Send buffer:
cc: 0, hiwat: 9216, lowat: 2048, flags:
Context: management
Local host: * (161), Foreign host: * (0)
Protocol: udp, type: dgram, ttl: 64, tos: 0, Id: 1
Options: none, state:
Receive buffer:
cc: 0, hiwat: 131072, lowat: 1, flags: none
Send buffer:
cc: 0, hiwat: 131072, lowat: 2048, flags:
Context: management
Local host: * (161), Foreign host: * (0)
Protocol: udp6, type: dgram, ttl: 64, tos: 0, Id: 2
Options: none, state:
Receive buffer:
cc: 0, hiwat: 131072, lowat: 1, flags: none
Send buffer:
cc: 0, hiwat: 131072, lowat: 2048, flags:
Context: management
Local host: 127.0.0.1 (123), Foreign host: * (0)
Protocol: udp, type: dgram, ttl: 64, tos: 0x10, Id: 12
Options: none, state: none
Receive buffer:
cc: 0, hiwat: 42240, lowat: 1, flags: none
Send buffer:
cc: 0, hiwat: 9216, lowat: 2048, flags:
Context: management
Local host: 127.0.0.1 (130), Foreign host: * (0)
Protocol: udp, type: dgram, ttl: 64, tos: 0, Id: 9
Options: none, state:
Receive buffer:
cc: 0, hiwat: 42240, lowat: 1, flags: none
Send buffer:
cc: 0, hiwat: 9216, lowat: 2048, flags:
Context: management
Local host: 127.0.0.1 (27613), Foreign host: 127.0.0.1 (123)
Protocol: udp, type: dgram, ttl: 64, tos: 0, Id: 8
Options: , state: none
Receive buffer:
cc: 0, hiwat: 42240, lowat: 1, flags:
Send buffer:
cc: 0, hiwat: 9216, lowat: 2048, flags:
Context: management
Total number of raw sockets: 0
Related Commands
show tcp statistics
To display TCP protocol statistics, use the show tcp statistics command.
show tcp statistics [all | tcp4 | tcp6 | tcpsum | udp4 | udp6 | udpsum | raw4 | raw6 | rawsum]
Syntax Description
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display TCP protocol statistics:
n1000v# show tcp statistics
TCP Received:
479908 packets total
0 checksum error, 0 bad offset, 0 too short, 0 MD5 error
232451 packets (72213943 bytes) in sequence
195 duplicate packets (192 bytes)
0 partially dup packets (0 bytes)
8652 out-of-order packets (0 bytes)
0 packets (0 bytes) with data after window
2 packets after close
0 window probe packets, 0 window update packets
44339 duplicate ack packets, 0 ack packets with unsent data
252581 ack packets (103465405 bytes)
TCP Sent:
533421 total, 0 urgent packets
94694 control packets
326430 data packets (105082025 bytes)
90 data packets (22114 bytes) retransmitted
105144 ack only packets
34 window probe packets, 7029 window update packets
TCP:
44330 connections initiated, 6715 connections accepted, 50669 connections established
51045 connections closed (including 165 dropped, 376 embryonic dropped)
3067 total rxmt timeout, 0 connections dropped in rxmt timeout
463 keepalive timeout, 92 keepalive probe, 371 connections dropped in keepalive
Related Commands
|
|
|
|---|---|
show tcp connection |
Displays information about the TCP connection. |
show tcp statistics |
Displays TCP protocol statistics. |
show tech-support
To collect switch information for Cisco TAC to assist you in diagnosing issues, use the show tech-support command.
show tech-support {aclmgr | dhcp | ipqos | ipv6 | netflow | svs | vsd}
Syntax Description
Defaults
None
Command Modes
Any
network-admin
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to collect switch information for Cisco TAC regarding IPv6 issues:
n1000v# show tech-support ipv6
`show ipv6 interface vrf all`
`show ipv6 static-route`
IPv6 Configured Static Routes
`show ipv6 statistic`
FTM related Statistics
ftm_stats_get : 0.00 0
ftm_stats_get_init : 0.00 0
ftm_stats_get_tx : 0.00 0
ftm_stats_get_rx : 0.00 0
ftm_stats_get_flush : 0.00 0
ftm_stats_get_radix : 0.00 0
ftm_stats_csm_fp : 0.00 0
`show ipv6 client`
IPv6 Registered Client Status
Client: icmpv6, status: up, pid: 3021, extended pid: 3021
Protocol: 58, pib-index: 4, routing context id: 255
Control mts SAP: 1280
Data mts SAP: 1281
IPC messages to control mq: 0
IPC messages to data mq: 0
Client: tcpudp, status: up, pid: 3022, extended pid: 3022
Protocol: 17, pib-index: 3, routing context id: 255
Control mts SAP: 1219
Data mts SAP: 1220
IPC messages to control mq: 1
IPC messages to data mq: 0
Recv fn: tcp_process_ipv6_data_msg (0x81fd22a)
Client: tcpudp, status: up, pid: 3022, extended pid: 3022
Protocol: 6, pib-index: 2, routing context id: 255
Control mts SAP: 1219
Data mts SAP: 1220
IPC messages to control mq: 1
IPC messages to data mq: 0
Recv fn: tcp_process_ipv6_data_msg (0x81fd22a)
`show ipv6 traffic`
IPv6 Software Processed Traffic and Error Statistics, last reset: never
RP-Traffic Statistics:
Counter Unicast Multicast
------- ------- ---------
Packets forwarded: 0 0
Bytes forwarded: 0 0
Packets originated: 0 0
Bytes originated: 0 0
Packets consumed: 0 0
Bytes consumed: 0 0
Fragments originated: 0 0
Fragments consumed: 0 0
Error Statistics:
Bad version: 0, route lookup failed: 0, hop limit exceeded: 0
Option header errors: 0, payload length too small: 0
PM errors: 0, MBUF errors: 0, encapsulation errors: 0
Syntax error while parsing 'show ipv6 route'
`show ipv6 internal mem-stats all`
Mem stats for IPV6
Private Mem stats for UUID : Malloc track Library(103) Max types: 5
--------------------------------------------------------------------------------
Curr alloc: 1591 Curr alloc bytes: 76678(74k)
IPC messages to control mq: 0
Curr alloc: 1522 Curr alloc bytes: 164596(160k)
Private Mem stats for UUID : Routing IPC Library(528) Max types: 10
--------------------------------------------------------------------------------
Curr alloc: 0 Curr alloc bytes: 0(0k)
Private Mem stats for UUID : Routing Library for managing mbufs(522) Max types:
6
--------------------------------------------------------------------------------
Curr alloc: 120 Curr alloc bytes: 485008(473k)
Private Mem stats for UUID : Patricia Trie Library(523) Max types: 3
--------------------------------------------------------------------------------
Curr alloc: 29 Curr alloc bytes: 916(0k)
IPC messages to control mq: 0
Curr alloc: 1522 Curr alloc bytes: 164596(160k)
Private Mem stats for UUID : Routing IPC Library(528) Max types: 10
--------------------------------------------------------------------------------
Curr alloc: 0 Curr alloc bytes: 0(0k)
Private Mem stats for UUID : Routing Library for managing mbufs(522) Max types:
6
--------------------------------------------------------------------------------
Curr alloc: 120 Curr alloc bytes: 485008(473k)
Private Mem stats for UUID : Patricia Trie Library(523) Max types: 3
--------------------------------------------------------------------------------
Curr alloc: 29 Curr alloc bytes: 916(0k)
IPC messages to control mq: 0
Curr alloc: 1522 Curr alloc bytes: 164596(160k)
Private Mem stats for UUID : Routing IPC Library(528) Max types: 10
--------------------------------------------------------------------------------
Curr alloc: 0 Curr alloc bytes: 0(0k)
Private Mem stats for UUID : Routing Library for managing mbufs(522) Max types:
6
--------------------------------------------------------------------------------
Curr alloc: 120 Curr alloc bytes: 485008(473k)
Private Mem stats for UUID : Patricia Trie Library(523) Max types: 3
--------------------------------------------------------------------------------
Curr alloc: 29 Curr alloc bytes: 916(0k)
IPC messages to control mq: 0
Curr alloc: 1522 Curr alloc bytes: 164596(160k)
Private Mem stats for UUID : Routing IPC Library(528) Max types: 10
--------------------------------------------------------------------------------
Curr alloc: 0 Curr alloc bytes: 0(0k)
Private Mem stats for UUID : Routing Library for managing mbufs(522) Max types:
6
--------------------------------------------------------------------------------
Curr alloc: 120 Curr alloc bytes: 485008(473k)
Private Mem stats for UUID : Patricia Trie Library(523) Max types: 3
--------------------------------------------------------------------------------
Curr alloc: 29 Curr alloc bytes: 916(0k)
Curr alloc: 0 Curr alloc bytes: 0(0k)
Private Mem stats for UUID : libfsrv(404) Max types: 11
--------------------------------------------------------------------------------
Curr alloc: 65 Curr alloc bytes: 1888(1k)
Private Mem stats for UUID : FSM Utils(53) Max types: 68
--------------------------------------------------------------------------------
Curr alloc: 10 Curr alloc bytes: 376(0k)
Private Mem stats for UUID : IM LIB(319) Max types: 33
--------------------------------------------------------------------------------
Curr alloc: 0 Curr alloc bytes: 0(0k)
Private Mem stats for UUID : Packet Manager(263) Max types: 16
--------------------------------------------------------------------------------
Curr alloc: 22 Curr alloc bytes: 236504(230k)
Private Mem stats for UUID : Internet Protocol version 6 (IPv6)(269) Max types:
16
--------------------------------------------------------------------------------
Curr alloc: 6 Curr alloc bytes: 1088(1k)
Private Mem stats for UUID : Transmission Control Protocol (TCP)(271) Max types:
18
--------------------------------------------------------------------------------
Curr alloc: 70 Curr alloc bytes: 272444(266k)
Private Mem stats for UUID : Lcache(544) Max types: 3
Private Mem stats for UUID : Adjacency Manager(264) Max types: 16
--------------------------------------------------------------------------------
Curr alloc: 0 Curr alloc bytes: 0(0k)
Private Mem stats for UUID : Internet Control Message Protocol version 6 (ICMPv6
)(270) Max types: 27
--------------------------------------------------------------------------------
Curr alloc: 0 Curr alloc bytes: 0(0k)
Private Mem stats for UUID : NF DDB Utils(515) Max types: 15
--------------------------------------------------------------------------------
Curr alloc: 0 Curr alloc bytes: 0(0k)
Curr alloc: 3838 Curr alloc bytes: 15194210 (14838k)
Shared Mem stats for UUID : Non mtrack users(0) Max types: 155
Shared Mem stats for UUID : Patricia Trie Library(523) Max types: 2
--------------------------------------------------------------------------------
Curr alloc: 2 Curr alloc bytes: 64(0k)
Shared Mem stats for UUID : Slab Library(529) Max types: 3
--------------------------------------------------------------------------------
Curr alloc: 4 Curr alloc bytes: 288(0k)
Shared Mem stats for UUID : Bitlogic Library(517) Max types: 6
--------------------------------------------------------------------------------
Curr alloc: 0 Curr alloc bytes: 0(0k)
Shared Mem stats for UUID : Cisco Regex Package(525) Max types: 2
--------------------------------------------------------------------------------
Curr alloc: 0 Curr alloc bytes: 0(0k)
--------------------------------------------------------------------------------
Curr alloc: 0 Curr alloc bytes: 0(0k)
Shared Mem stats for UUID : Routing Queue Library(526) Max types: 2
--------------------------------------------------------------------------------
Curr alloc: 0 Curr alloc bytes: 0(0k)
Shared Mem stats for UUID : Internet Protocol (IP)(267) Max types: 12
--------------------------------------------------------------------------------
Curr alloc: 10 Curr alloc bytes: 65888(64k)
Shared Mem stats for UUID : SMM Library(561) Max types: 2
--------------------------------------------------------------------------------
Curr alloc: 0 Curr alloc bytes: 0(0k)
Shared Mem stats for UUID : Internet Protocol version 6 (IPv6)(269) Max types: 1
4
--------------------------------------------------------------------------------
Curr alloc: 7 Curr alloc bytes: 536(0k)
Shared Mem stats for UUID : Adjacency Manager(264) Max types: 5
--------------------------------------------------------------------------------
Curr alloc: 0 Curr alloc bytes: 0(0k)
Curr alloc: 23 Curr alloc bytes: 66776 (65k)
n1000v#
Related Commands
|
|
|
|---|---|
show logging logfile |
Displays the contents of the log file. |
logging logfile |
Configures the log file used to store system messages. |
show telnet server
To display the Telnet server configuration, use the show telnet server command.
show telnet server
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the Telnet server configuration:
n1000v# show telnet server
telnet service enabled
n1000v#
Related Commands
|
|
|
|---|---|
show tcp connection |
Displays information about the connection. |
telnet |
Uses Telnet to connect to another system. |
telnet6 |
Uses Telnet6 to connect to another system. |
show terminal
To display the terminal settings for the current session, use the show terminal command.
show terminal
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display the terminal settings for the current session:
n1000v# show terminal
TTY: /dev/pts/8 type: "vt100"
Length: 24 lines, Width: 88 columns
Session Timeout: None
n1000v#
Related Commands
show user-account
To display user account configuration, use the show user-account command.
show user-account [username]
Syntax Description
username |
(Optional) Name of a user with an existing account. |
Defaults
None
Command Modes
Any
network-admin
network-operator
Command History
|
|
|
4.0(4)SV1(1) |
This command was introduced. |
Examples
This example shows how to display user account configuration for the user called NewUser:
n1000v(config)# show user-account NewUser
user:NewUser
this user account has no expiry date
roles:network-operator network-admin
n1000v(config)#
Related Commands
show users
To display information about the user session, use the show users command.
show users
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Any
network-admin
network-operator