Cisco Nexus 1000V Command Reference, Release 4.0(4)SV1(1)

C Commands

This chapter describes the Cisco Nexus 1000V commands that begin with the letter, C.

cache size

To specify a cache size for a Netflow flow monitor, use the cache size command. To remove the cache size for a flow monitor, use the no form of this command.

cache size value

no cache size value

Syntax Description

Defaults

4096 entries

Command Modes

Netflow Monitor Configuration (config-flow-monitor)

network-admin

Command History

Usage Guidelines

Use the cache-size command to limit the impact of the Netflow flow monitor cache on memory and performance.

Examples

This example shows how to configure the cache size for a Netflow flow monitor named MonitorTest, and then display the configuration:

n1000v# config t

n1000v(config)# flow monitor MonitorTest

n1000v(config-flow-monitor)# cache size 15000

n1000v(config-flow-monitor)# show flow monitor MonitorTestFlow 

Monitor monitortest: 

     Use count: 0 

     Inactive timeout: 600 

     Active timeout: 1800 

     Cache Size: 15000

n1000v(config-flow-monitor)#

This example shows how to remove a cache size from a flow monitor:

n1000v# config t

n1000v(config)# flow monitor MonitorTest

n1000v(config-flow-monitor)# no cache size 

n1000v(config-flow-monitor)#show flow monitor MonitorTestFlow

n1000v(config-flow-monitor)# 

Monitor monitortest: 

     Use count: 0 

     Inactive timeout: 600 

     Active timeout: 1800 

     Cache Size: 4096

n1000v(config-flow-monitor)#

Related Commands

capability

To set a particular profile capability, use the capability command. To remove the profile capability, use the no form of this command.

capability {uplink | l3control}

no capability [uplink | l3control]

Syntax Description

Defaults

None

Command Modes

Port Profile Configuration (config-port-prof)

network-admin

Command History

Usage Guidelines

This command allows the port to be used as an uplink port. In vCenter Server, the port groups with uplink port profiles can be selected and assigned to physical ports (a vmnic or a pnic).

Note If a port profile is configured as an uplink, then it cannot be used to configure VMware virtual ports.

Examples

This example shows how to configure a particular port profile capability:

n1000v(config-port-prof)# capability uplink

This example shows how to remove the port profile configuration:

n1000v(config)# no capability uplink

Related Commands

cd

To change to a different directory from the one you are currently working in, use the cd command.

cd [filesystem:[//directory] | directory]

Syntax Description

Defaults

bootflash

Command Modes

Any

network-admin

Usage Guidelines

You can only change to the directories that are on the active supervisor module.

Use the present working directory (pwd) command to verify the name of the directory you are currently working in.

Examples

This example shows how to change to a different directory on the current file system:

n1000v# cd my-scripts

This example shows how to change from the file system you are currently working in to a different file system:

n1000v# cd volatile:

This example shows how to revert back to the default directory, bootflash:

n1000v# cd

Related Commands

cdp advertise

To specify the CDP version to advertise, use the cdp advertise command. To remove the cdp advertise configuration, use the no form of this command.

cdp advertise {v1 | v2}

no cdp advertise [v1 | v2]

Syntax Description

Defaults

CDP Version 2

Command Modes

Global Configuration (config)

network-admin

Command History

Usage Guidelines

Examples

This example shows how to set CDP Version 1 as the version to advertise:

n1000v(config)# cdp advertise v1

This example shows how to remove CDP Version 1 as the configuration to advertise:

n1000v(config)# no cdp advertise v1

Related Commands

cdp enable (global)

To enable Cisco Discovery Protocol (CDP) globally on all interfaces and port channels, use the cdp enable command. To disable CDP globally, use the no form of this command.

cdp enable

no cdp enable

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Global Configuration (config)

network-admin

Command History

Usage Guidelines

CDP can only be configured on physical interfaces and port channels.

Examples

This example shows how to enable CDP globally and then show the CDP configuration:

n1000v# config t

n1000v(config)# cdp enable

n1000v(config)# show cdp global

Global CDP information:

    CDP enabled globally

    Refresh time is 60 seconds

    Hold time is 180 seconds

    CDPv2 advertisements is enabled

    DeviceID TLV in System-Name(Default) Format

This example shows how to disable CDP globally and then show the CDP configuration:

n1000v(config)# no cdp enable

n1000v# show cdp global

Global CDP information:

    CDP disabled globally

    Refresh time is 60 seconds

    Hold time is 180 seconds

    CDPv2 advertisements is enabled

    DeviceID TLV in System-Name(Default) Format

n1000v(config)# 

Related Commands

cdp enable (interface or port channel)

To enable Cisco Discovery Protocol (CDP) on an interface or port channel, use the cdp enable command. To disable it, use the no form of this command.

cdp enable

no cdp enable

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Interface Configuration (config-if)

network-admin

Command History

Usage Guidelines

CDP must be enabled globally before you configure the device ID format.

CDP can only be configured on physical interfaces and port channels.

Examples

This example shows how to enable CDP on port channel 2:

n1000v# config t

n1000v(config)# interface port-channel2

n1000v(config-if)# cdp enable

n1000v(config-if)# 

This example shows how to disable CDP on mgmt0:

n1000v# config t

n1000v(config)# interface mgmt0

n1000v(config-if)# no cdp enable

n1000v(config-if)# show cdp interface mgmt0

        mgmt0 is up 

        CDP disabled on interface 

        Sending CDP packets every 60 seconds 

        Holdtime is 180 seconds

n1000v(config-if)#

Related Commands

cdp format device-id

To specify the device ID format for CDP, use the cdp format device-id command. To remove it, use the no form of this command.

cdp format device-id {mac-address | serial-number | system-name}

no cdp format device-id {mac-address | serial-number | system-name}

Syntax Description

Defaults

System name/Fully Qualified Domain Name

Command Modes

Global Configuration (config)

network-admin

Command History

Usage Guidelines

CDP must be enabled globally before you configure the device ID format.

You can configure CDP on physical interfaces and port channels only.

Examples

This example shows how to configure the CDP device ID with the MAC address format and then display the configuration:

n1000v(config)# cdp format device-id mac-address

n1000v(config)# show cdp global 

Global CDP information: 

CDP enabled globally 

     Sending CDP packets every 5 seconds 

     Sending a holdtime value of 10 seconds 

     Sending CDPv2 advertisements is disabled 

     Sending DeviceID TLV in Mac Address Format

This example shows how to remove the CDP device ID MAC address format from the configuration:

n1000v(config)# no cdp format device-id mac-address

Related Commands

cdp holdtime

To do set the maximum amount of time that CDP holds onto neighbor information before discarding it, use the cdp holdtime command. To remove the CDP holdtime configuration, use the no form of this command.

cdp holdtime seconds

no cdp holdtime seconds

Syntax Description

Defaults

180 seconds

Command Modes

Global Configuration (config)

network-admin

Command History

Usage Guidelines

CDP must be enabled globally before you configure the device ID format.

You can configure CDP on physical interfaces and port channels only.

Examples

This example shows how to set the CDP holdtime to 10 second:

n1000v(config)# cdp holdtime 10

This example shows how to remove the CDP holdtime configuration:

n1000v(config)# no cdp holdtime 10

Related Commands

cdp timer

To set the refresh time for CDP to send advertisements to neighbors, use the cdp timer command. To remove the CDP timer configuration, use the no form of this command.

cdp timer seconds

no cdp timer seconds

Syntax Description

Defaults

60 seconds

Command Modes

Global Configuration (config)

network-admin

Command History

Usage Guidelines

Examples

This example shows how to configure the CDP timer to 10 seconds:

n1000v(config)# cdp timer 10

This example shows how to remove the CDP timer configuration:

n1000v(config)# no cdp timer 10

Related Commands

channel-group auto (port profile)

To create and define a channel group for all interfaces belonging to a port profile, use the channel-group auto command. To remove the channel-group, use the no form of this command.

channel-group auto [mode channel_mode] [sub-group cdp]

no channel-group

Syntax Description

Defaults

None

Command Modes

Port Profile Configuration (config-port-prof)

network-admin

Command History

Usage Guidelines

The channel-group auto command creates a unique port channel for all interfaces belonging to the same module. The channel-group is automatically assigned when the port profile is assigned to the first interface. Each additional interface belonging to the same module is added to the same port-channel. In VMware environments, a different port channel is created for each module.

•The channel group mode must be set to on.

•When configuring a port channel for a port profile that connects to two upstream switches, also called virtual port channel host mode (vPC-HM):

–You know whether CDP is configured in the upstream switches.

If so, then CDP creates a subgroup for each upstream switch to manage its traffic separately.

If CDP is not configured in the upstream switch, then you must manually configure subgroups to manage the traffic flow on the separate switches.

–If vPC-HM is not configured when port channels connect to two different upstream switches, then the VMs behind the Cisco Nexus 1000V receive duplicate packets from the network for broadcast/unknown floods/multicast.

vPC-HM can also be configured on the interface. For more information, see the Cisco Nexus 1000V Interface Configuration Guide, Release 4.0(4)SV1(1).

Examples

This example shows how to configure a port channel for a port profile that connects to a single upstream switch, and then display the configuration:

n1000v# config t

n1000v(config)# port-profile AccessProf

n1000v(config-port-prof)# channel-group auto mode on

n1000v(config-port-prof)# show port-profile name AccessProf

port-profile AccessProf

  description: allaccess4

  status: disabled

  capability uplink: yes

  port-group: AccessProf

  config attributes:

    switchport mode access

    channel-group auto mode on

  evaluated config attributes:

    switchport mode access

    channel-group auto mode on

  assigned interfaces:

n1000v(config-port-prof)# 

This example shows how to remove the channel group configuration from the port profile and then 
display the configuration:

n1000v# config t

n1000v(config)# port-profile AccessProf

n1000v(config-port-prof)# no channel-group 

n1000v(config-port-prof)# show port-profile name AccessProf

port-profile AccessProf

  description: allaccess4

  status: disabled

  capability uplink: yes

  port-group: AccessProf

  config attributes:

    switchport mode access

evaluated config attributes:

    switchport mode access

assigned interfaces:

n1000v(config-port-prof)# 

This example shows how to configure an uplink port profile, to be used by the physical NICs in the VEM, in vPC-HM when the ports in the port channel connect to two different upstream switches:

n1000v# config t

n1000v(config)# port-profile uplinkProf

n1000v(config-port-prof)# channel-group auto mode on sub-group cdp

doc-n1000v(config-port-prof)# show port-profile name uplinkProf

port-profile uplinkProf

  description: 

  status: disabled

  capability uplink: no

  capability l3control: no

  system vlans: none

  port-group: 

  max-ports: 32

  inherit:

  config attributes:

    channel-group auto mode on sub-group cdp

  evaluated config attributes:

    channel-group auto mode on sub-group cdp

  assigned interfaces:

n1000v(config-port-prof)# 

Related Commands

channel-group (interface)

To create a port channel group or to move an interface from one port channel group to another, use the channel-group command. To remove the channel group configuration from an interface, use the no form of this command.

channel-group number [force] [mode {active | on | passive}]

no channel-group [number]

Syntax Description

Defaults

The default mode is on.

Command Modes

Interface Configuration (config-if)

network-admin

Command History

Usage Guidelines

A port channel in the on channel mode is a pure port channel and can aggregate a maximum of eight ports. It does not run LACP.

If an existing port channel is not running LACP you cannot change the mode for it or any of its interfaces. If you try to do so, the channel mode remains on and an error message is generated.

When you delete the last physical interface from a port channel, the port channel remains. To delete the port channel completely, use the no form of the port-channel command.

When an interface joins a port channel, the following attributes are removed and replaced with the those of the port channel:

•Bandwidth

•Delay

•Extended Authentication Protocol over UDP

•VRF

•IP address

•MAC address

•Spanning Tree Protocol

•NAC

•Service policy

•Quality of Service (QoS)

•ACLs

The following attributes remain unaffected when an interface joins or leaves a port channel:

•Beacon

•Description

•CDP

•LACP port priority

•Debounce

•UDLD

•MDIX

•Rate mode

•Shutdown

•SNMP trap

You do not have to create a port channel interface before you assign a physical interface to a channel group. A port channel interface is created automatically when the channel group gets its first physical interface, if it is not already created.

Examples

This example shows how to add an interface to LACP channel group 5 in active mode:

n1000v(config-if)# channel-group 5 mode active

n1000v(config-if)#

Related Commands

check logflash

To check the compactFlash, use the check logflash command.

check logflash [bad-blocks]

Syntax Description

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

Examples

This example shows how to check compactFlash:

n1000v# check logflash

class (policy map type qos)

To add an existing Quality of Service (QoS) class to a policy map, use the class command. To remove a QoS class from a policy map, use the no form of this command.

class [type qos] {class-map-name | class-default} [insert-before [type qos] before-class-map-name]

no class {class-map-name | class-default}

Syntax Description

Defaults

type QoS

The default is to reference a new class map at the end of the policy map.

The class named class-default matches all traffic not classified in other classes.

Command Modes

Policy Map Configuration (config-pmap)

network-admin

Usage Guidelines

Policy actions in the first class that matches the traffic type are performed.

The class named class-default matches all traffic not classified in other classes.

Examples

This example shows how to add a class map in sequence to the end of a policy map:

n1000v(config)# policy-map my_policy1

n1000v(config-pmap)# class traffic_class2

n1000v(config-pmap-c-qos)# 

This example shows how to insert a class map in sequence before an existing class map in a policy map:

n1000v(config)# policy-map my_policy1

n1000v(config-pmap-qos)# class insert-before traffic_class2 traffic_class1

n1000v(config-pmap-c-qos)# 

This example shows how to add the class-default class map to a policy map:

n1000v(config)# policy-map my_policy1

n1000v(config-pmap-qos)# class class-default

n1000v(config-pmap-c-qos)# 

This example shows how to remove a class map reference from a policy map:

n1000v(config)# policy-map my_policy1

n1000v(config-pmap)# no class traffic_class1

n1000v(config-pmap)# 

Related Commands

class-map

To create or modify a QoS class map that defines a class of traffic, use the class-map command. To remove a class map, use the no form of this command.

class-map [type qos] [match-any | match-all] class-map-name

no class-map [type qos] [match-any | match-all] class-map-name

Syntax Description

Defaults

type QoS
match-all

Command Modes

Global configuration (config)

network-admin

Command History

Usage Guidelines

Hyphen, underscore, and alphabetic characters are allowed in the class map name.

Forty characters are the maximum allowed in the class map name.

Characters in the class map name are case sensitive.

Examples

This example shows how to create a class map and enter the QoS class map configuration mode to configure the specified map:

n1000v# configure terminal

n1000v(config)# class-map my_class1

n1000v(config-cmap-qos)#

This example shows how to remove the QoS class map named my_class1:

n1000v(config)# no class-map my_class1

n1000v(config)#

Related Commands

clear access-list counters

To clear the counters for IP and MAC access control list(s) (ACLs), use the clear access-list counters command.

clear access-list counters [access-list-name]

Syntax Description

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

If you specify an ACL, the name can be up to 64 alphanumeric, case-sensitive characters.

Examples

This example shows how to clear counters for all IP and MAC ACLs:

n1000v# clear access-list counters

n1000v#

This example shows how to clear counters for an IP ACL named acl-ip-01:

n1000v# clear access-list counters acl-ip-01

n1000v#

Related Commands

clear cdp

To clear Cisco Discovery Protocol(CDP) information on an interface, use the clear cdp command.

clear cdp {counters [interface slot/port] | table [interface slot/port]}

Syntax Description

Defaults

None

Command Modes

Any

network-admin
network-operator

Command History

Usage Guidelines

Examples

This example shows how to clear CDP counters on all interfaces:

n1000V# clear cdp counters

This example shows how to clear CDP cache on all interfaces:

n1000V# clear cdp table

Related Commands

clear cli history

To clear the history of commands you have entered into the CLI, use the clear cli history command.

clear cli history

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

Use the show cli history command to display the history of the commands that you entered at the command-line interface (CLI).

Examples

This example shows how to clear the command history:

n1000v# clear cli history

Related Commands

clear cores

To clear the core files, use the clear cores command.

clear cores [archive]

Syntax Description

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

Use the show system cores command to display information about the core files.

Examples

This example shows how to clear the core file:

n1000v# clear cores

This example shows how to clear the core on the logflash filesystem:

n1000v# clear cores archive

Related Commands

clear counters

To clear interface counters, use the clear counters command.

clear counters [ interface {all | ethernet slot/port | loopback virtual-interface-number | mgmt | port-channel port-channel-number | vethernet interface-number} ]

Syntax Description

Defaults

None

Command Modes

Any

network-admin
network-operator

Command History

Usage Guidelines

Examples

This example shows how to clear the Ethernet interface counters:

n1000v(config)# clear counters ethernet 2/1

Related Commands

clear debug-logfile

To clear the contents of the debug logfile, use the clear debug-logfile command.

clear debug-logfile filename

Syntax Description

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

Examples

This example shows how to clear the debug logfile:

n1000v# clear debug-logfile syslogd_debugs

Related Commands

clear flow exporter

To clear the statistics for a Flexible NetFlow flow exporter, use the clear flow exporter command in Any.

clear flow exporter {name exporter-name | exporter-name}

Syntax Description

Command Default

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

You must have already enabled traffic monitoring with Flexible NetFlow using an exporter before you can use the clear flow exporter command.

Examples

The following example clears the statistics for the flow exporter named NFC-DC-PHOENIX:

n1000v# clear flow exporter name NFC-DC-PHOENIX

n1000v#

Related Commands

clear ip access-list counters

To clear the counters for IP access control lists (ACLs), use the clear ip access-list counters command.

clear ip access-list counters [access-list-name]

Syntax Description

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

If specifying an ACL by name, it can be up to 64 alphanumeric, case-sensitive characters.

Examples

This example shows how to clear counters for all IP ACLs:

n1000v# clear ip access-list counters

n1000v#

This example shows how to clear counters for an IP ACL named acl-ip-101:

n1000v# clear ip access-list counters acl-ip-101

n1000v#

Related Commands

clear ip igmp interface statistics

To clear the IGMP statistics for an interface, use the clear ip igmp interface statistics command.

clear ip igmp interface statistics [if-type if-number]

Syntax Description

Defaults

None

Command Modes

Any

network-admin
network-operator

Command History

Usage Guidelines

Examples

This example shows how to clear IGMP statistics for an interface:

n1000v# clear ip igmp interface statistics ethernet 2/1

n1000v# 

Related Commands

clear ip igmp snooping statistics vlan

To clear the IGMP snooping statistics for VLANs, use the clear ip igmp snooping statistics vlan command.

clear ip igmp snooping statistics vlan {vlan-id | all}

Syntax Description

Defaults

None

Command Modes

Any

network-admin
network-operator

Command History

Usage Guidelines

Examples

This example shows how to clear IGMP snooping statistics for VLAN 1:

n1000v# clear ip igmp snooping statistics vlan 1

n1000v# 

Related Commands

clear lacp counters

To clear the statistics for all interfaces for Link Aggregation Control Protocol (LACP) groups, use the clear lacp counters command.

clear lacp counters [interface port-channel channel-number]

Syntax Description

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

If you clear counters for a specific port channel, the allowable port channel numbers are from 1 to 4096.

If you do not specify a channel number, the LACP counters for all LACP port groups are cleared.

If you clear counters for a static port-channel group, without the aggregation protocol enabled, the device ignores the command.

Examples

This example shows how to clear all the LACP counters:

n1000v(config)# clear lacp counters

n1000v(config) # 

This example shows how to clear all LACP counters for the LACP port-channel group 20:

n1000v(config)# clear lacp counters interface port-channel 20

n1000v(config)# 

Related Commands

clear license

To uninstall a license file from a VSM, or to uninstall an evaluation license before installing a permanent license, use the clear license command.

clear license filename

Syntax Description

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

If a license is in use, you cannot uninstall it. Before uninstalling the license file, all licenses must first be transferred from the VEMs to the VSM license pool.

Caution Service Disruption
When you uninstall a license file from a VSM, the vEthernet interfaces on the VEMs are removed from service and the traffic flowing to them from virtual machines is dropped. This traffic flow is not resumed until you add a new license file with licenses for the VEMs. We recommend notifying the server administrator that you are uninstalling a license and that this will cause the vEthernet interfaces to shut down.

Examples

This example shows how to remove the Enterprise.lic license file from a VSM:

n1000v# clear license Enterprise.lic 

Clearing license Enterprise.lic:

SERVER this_host ANY

VENDOR cisco

Do you want to continue? (y/n) y

Clearing license ..done

n1000v# 

Related Commands

clear line

To end a session on a specified vty, use the clear line command.

clear line word

Syntax Description

Defaults

None

Command Modes

Any

network-admin
network-operator

Command History

Usage Guidelines

Examples

This example shows how to end a session on a specified vty:

n1000v(config)# clear line

Related Commands

clear logging logfile

Use the clear logging logfile command to clear messages from the logging file.

clear logging logfile

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Any

Super user

Command History

Usage Guidelines

Examples

This example shows how to clear messages from the logging file:

n1000v# clear logging logfile 

n1000v# 

Related Commands

clear logging session

Use the clear logging session command to clear the current logging session.

clear logging session

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Any

Super user

Command History

Usage Guidelines

Examples

This example shows how to clear the current logging session:

n1000v# clear logging session 

n1000v#

Related Commands

clear mac access-list counters

To clear the counters for MAC access control lists (ACLs), use the clear mac access-list counters command.

clear mac access-list counters [access-list-name]

Syntax Description

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

If you want counters cleared for a specific MAC ACL, the name can be up to 64 alphanumeric, case-sensitive characters.

Examples

This example shows how to clear counters for all MAC ACLs:

n1000v# clear mac access-list counters

n1000v#

This example shows how to clear counters for a MAC ACL named acl-mac-0060:

n1000v# clear mac access-list counters acl-mac-0060

n1000v#

Related Commands

clear mac address-table dynamic

To clear the dynamic address entries from the MAC address table in Layer 2, use the clear mac address-table dynamic command.

clear mac address-table dynamic [[address mac_addr] [vlan vlan-id] [interface {type slot/port | port-channel number}]

Syntax Description

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

Use the clear mac address-table dynamic command with no arguments to remove all dynamic entries from the table.

To clear static MAC addresses from the table, use the no mac address-table static command.

If the clear mac address-table dynamic command is entered with no options, all dynamic addresses are removed. If you specify an address but do not specify an interface, the address is deleted from all interfaces. If you specify an interface but do not specify an address, the device removes all addresses on the specified interfaces.

Examples

This example shows how to clear all the dynamic Layer 2 entries from the MAC address table:

n1000v(config)# clear mac address-table dynamic 

n1000v(config) # 

This example shows how to clear all the dynamic Layer 2 entries from the MAC address table for VLAN 20 on port 2/20:

n1000v(config)# clear mac address-table dynamic vlan 20 interface ethernet 2/20

n1000v(config)# 

Related Commands

clear ntp statistics

To clear the Network Time Protocol statistics, use the clear ntp statistics command.

clear ntp statistics {all-peers | io | local | memory}

Syntax Description

Defaults

None

Command Modes

Any

network-admin
network-operator

Command History

Usage Guidelines

Examples

This example shows how to clear statistics for all NTP peers:

n1000v(config)# clear ntp statistics all-peers

Related Commands

clear port-security

To clear dynamically-learned, secure MAC address(es), use the clear port-security command.

clear port-security {dynamic} {interface vethernet veth-number | address address} [vlan vlan-id]

Syntax Description

Defaults

dynamic

Command Modes

Any

network-admin

Command History

Usage Guidelines

Examples

This example shows how to remove dynamically learned, secure MAC addresses from the veth1 interface:

n1000v# config t

n1000v(config)# clear port-security dynamic interface veth 1

This example shows how to remove the dynamically learned, secure MAC address 0019.D2D0.00AE:

n1000v# config t

n1000v(config)# clear port-security dynamic address 0019.D2D0.00AE

Related Commands

clear qos statistics

To clear the counters for QoS statistics, use the clear qos statistics command.

clear qos statistics {interface [ethernet type/slot | vethernet number | port-channel number] } [input type qos | output type qos]}

Syntax Description

Defaults

None

Command Modes

Any

network-admin
network-operator

Command History

Usage Guidelines

If you do not specify an interface, the counters are cleared for all interfaces.

Examples

This example shows how to clear QoS statistics for all interfaces:

n1000v# clear qos statistics

n1000v# 

This example shows how to clear all input QoS statistics for veth2:

n1000v# clear qos statistics veth2 input type qos

n1000v# 

Related Commands

clear ssh hosts

To clear the Secure Shell (SSH) host sessions, use the clear ssh hosts command.

clear ssh hosts

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

Examples

This example shows how to clear all SSH host sessions:

n1000v# clear ssh hosts

Related Commands

clear system reset-reason

To clear the device reset-reason history, use the clear system reset-reason command.

clear system reset-reason

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

Examples

This example shows how to clear reset-reason history:

n1000v# clear system reset-reason

Related Commands

clear user

To clear a user session, use the clear user command.

clear user user-id

Syntax Description

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

Use the show users command to display the current user sessions on the device.

Examples

This example shows how to clear all SSH host sessions:

n1000v# clear user user1

Related Commands

cli var name

To define a command line interface (CLI) variable for a terminal session, use the cli var name command. To remove the CLI variable, use the no form of this command.

cli var name variable-name variable-text

cli no var name variable-name

Syntax Description

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

You can reference a CLI variable using the following syntax:

$(variable-name)

Instances where you can use variables in include the following:

•Command scripts

•Filenames

You cannot reference a variable in the definition of another variable.

You can use the predefined variable, TIMESTAMP, to insert the time of day. You cannot change or remove the TIMESTAMP CLI variable.

You must remove a CLI variable before you can change its definition.

Examples

This example shows how to define a CLI variable:

n1000v# cli var name testinterface interface 2/3

This example shows how to reference the TIMESTAMP variable:

n1000v# copy running-config > bootflash:run-config-$(TIMESTAMP).cnfg

This example shows how to remove a CLI variable:

n1000v# cli no var name testinterface interface 2/3

Related Commands

clock set

To manually set the clock, use the clock set command.

clock set time day month year

Syntax Description

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

Use this command when you cannot synchronize your device with an outside clock source, such as NTP.

Examples

This example shows how to manually set the clock:

n1000v# clock set 9:00:00 1 June 2008

Related Commands

clock summer-time

To configure the summer-time (daylight saving time) offset, use the clock summer-time command. To revert to the default, use the no form of this command.

clock summer-time zone-name start-week start-day start-month start-time end-week end-day end-month end-time offset-minutes

no clock summer-time

Syntax Description

Defaults

None

Command Modes

Global Configuration (config)

network-admin

Command History

Usage Guidelines

Examples

This example shows how to configure the offset for summer-time or daylight saving time:

n1000v# configure terminal

n1000v(config)# clock summer-time PDT 1 Sunday March 02:00 1 Sunday November 02:00 60

This example shows how to remove the summer-time offset:

n1000v# configure terminal

n1000v(config)# no clock summer-time

Related Commands

clock timezone

To configure the time zone offset from Coordinated Universal Time (UTC), use the clock timezone command. To revert to the default, use the no form of this command.

clock timezone zone-name offset-hours offset-minutes

no clock timezone

Syntax Description

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

Examples

This example shows how to configure the time zone offset from UTC:

n1000v# clock timezone EST 5 0

This example shows how to remove the time zone offset:

n1000v# no clock timezone

Related Commands

collect counter

To configure the number of bytes or packets in a flow as a non-key field and collect the number of bytes or packets seen for a Flexible NetFlow flow record, use the collect counter command. To disable the counters, use the no form of this command.

collect counter {bytes [long] | packets [long]}

no collect counter {bytes [long] | packets [long]}

Syntax Description

Command Default

This command is not enabled by default.

Command Modes

Flow Record Configuration

network-admin

Command History

Usage Guidelines

Examples

The following example enables collecting the total number of bytes from the flows as a non-key field:

n1000v(config)# flow record FLOW-RECORD-1

n1000v(config-flow-record)# collect counter bytes

The following example enables collecting the total number of bytes from the flows as a non-key field using a 64 bit counter:

n1000v(config)# flow record FLOW-RECORD-1

n1000v(config-flow-record)# collect counter bytes long

The following example enables collecting the total number of packets from the flows as a non-key field:

n1000v(config)# flow record FLOW-RECORD-1

n1000v(config-flow-record)# collect counter packets

The following example enables collecting the total number of packets from the flows as a non-key field using a 64 bit counter:

n1000v(config)# flow record FLOW-RECORD-1

n1000v(config-flow-record)# collect counter packets long

Related Commands

collect timestamp sys-uptime

To collect the TIMESTAMP SYS-UPTIME for a NetFlow flow record, use the collect timestamp sys-uptime command. To disable the collection, use the no form of this command.

collect timestamp sys-uptime {first | last}

no collect timestamp sys-uptime {first | last}

Syntax Description

Command Default

This command is not enabled by default.

Command Modes

Flow Record Configuration

network-admin

Command History

Usage Guidelines

Examples

The following example enables collecting the sys-uptime for the time the first packet was seen from the flows:

n1000v(config)# flow record FLOW-RECORD-1

n1000v(config-flow-record)# collect timestamp sys-uptime first

The following example enables collecting the sys-uptime for the time the most recent packet was seen from the flows:

n1000v(config)# flow record FLOW-RECORD-1

n1000v(config-flow-record)# collect timestamp sys-uptime last

Related Commands

collect transport tcp flags

To collect a Transmission Control Protocol (TCP) flags for a NetFlow flow record, use the collect transport tcp flags command. To disable the collection, use the no form of this command.

collect transport tcp flags

no collect transport tcp flags

Syntax Description

This command has no arguments or keywords

Command Default

This command is not enabled by default.

Command Modes

Flow Record Configuration

network-admin

Command History

Usage Guidelines

Examples

The following example collects the TCP flags:

n1000v(config)# flow record FLOW-RECORD-1

n1000v(config-flow-record)# collect transport tcp flags

Related Commands

configure terminal

To access configuration commands in the CLI Global Configuration mode, use the configure terminal command.

configure terminal

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

The configuration changes you make in the Global Configuration mode are saved in the running configuration file. To save these changes persistently across reboots and restarts, you must copy them to the startup configuration file using the copy running-config startup-config command.

Examples

This example shows how to access configuration commands in the CLI Global Configuration mode:

n1000v# configure terminal

n1000v(config)# 

Related Commands

connect

To initiate a connection with vCenter, use the connect command. To disconnect from vCenter, use the no form of this command.

connect

no connect

Syntax Description

This command has no arguments or keywords.

Defaults

no connect

Command Modes

SVS Connect Configuration (config-svs-conn)

network-admin

Command History

Usage Guidelines

Upon connection to vCenter, if a username and password have not been configured for this connection, you are prompted to enter them.

There can be only one active connection at a time. If a previously-defined connection is up, an error message displays and the connect command is rejected until the previous connection is closed by entering no connect.

Examples

This example shows how to connect to vCenter:

n1000v(config#) svs connection vcWest

n1000v(config-svs-conn#) protocol vmware-vim

n1000v(config-svs-conn#) remote hostname vcMain

n1000v(config-svs-conn#) vmware dvs datacenter-name HamiltonDC

n1000v(config-svs-conn#) connect

This example shows how to disconnect from vCenter:

n1000v(config#) svs connection vcWest

n1000v(config-svs-conn#) no connect

Related Commands

control vlan

To assign a control VLAN to the Cisco Nexus 1000V domain, use the control vlan command. To remove the control VLAN, use the no form of this command.

control vlan number

no control vlan

Syntax Description

Defaults

None

Command Modes

SVS Domain Configuration (config-svs-domain)

network-admin

Command History

Usage Guidelines

Newly-created VLANs remain unused until Layer 2 ports are assigned to them.

If you enter a VLAN ID that is assigned to an internally allocated VLAN, the CLI returns an error message.

Examples

This example shows how to configure control VLAN 70 for domain ID 32:

n1000v# config t 

n1000v(config)# svs-domain

n1000v(config-svs-domain)# domain id 32

n1000v(config-svs-domain)# control vlan 70

n1000v(config-svs-domain)#

This example shows how to remove control VLAN 70 from domain ID 32:

n1000v# config t 

n1000v(config)# svs-domain

n1000v(config-svs-domain)# domain id 32

n1000v(config-svs-domain)# no control vlan 70

n1000v(config-svs-domain)#

Related Commands

copy

To copy a file from a source to a destination, use the copy command.

copy source-url destination-url

Syntax Description

The format of the source and destination URLs varies according to the file or directory location. You may enter either a command-line interface (CLI) variable for a directory or a filename that follows the Cisco NX-OS file system syntax (filesystem:[/directory][/filename]).

The following tables list URL prefix keywords by the file system type. If you do not specify a URL prefix keyword, the device looks for the file in the current directory.

Table 1 lists URL prefix keywords for bootflash and remote writable storage file systems.

Table 2 lists the URL prefix keywords for nonwritable file systems.

Defaults

The default name for the destination file is the source filename.

Command Modes

Any

network-admin

Command History

Usage Guidelines

The entire copying process may take several minutes, depending on the network conditions and the size of the file, and differs from protocol to protocol and from network to network.

The colon character (:) is required after the file system URL prefix keywords (such as bootflash).

In the URL syntax for ftp:, scp:, sftp:, and tftp:, the server is either an IP address or a host name.

Examples

This example shows how to copy a file within the same directory:

n1000v# copy file1 file2

This example shows how to copy a file to another directory:

n1000v# copy file1 my_files:file2

This example shows how to copy a file to another supervisor module:

n1000v# copy file1 bootflash://sup-remote/file1.bak

This example shows how to copy a file from a remote server:

n1000v# copy scp://10.10.1.1/image-file.bin bootflash:image-file.bin

Related Commands

copy running-config startup-config

To copy the running configuration to the startup configuration, use the copy running-config startup-config command.

copy running-config startup-config

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Any

network-admin

Command History

Usage Guidelines

Use this command to save configuration changes in the running configuration to the startup configuration in persistent memory. When a device reload or switchover occurs, the saved configuration is applied.

Examples

This example shows how to save the running configuration to the startup configuration:

n1000v# copy running-config startup-config

[########################################] 100%

Related Commands