Description: Add a custom MAC address to the bridgedomain
Syntax:
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# interface bridge-domain <WORD> (config-tenant-interface)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Manually set interface MAC address
Syntax:
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface vlan <1-4094> (config-leaf-if)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Configure mac Address
Syntax:
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Virtual MAC address
Syntax:
WORD |
MAC address(FORMAT:xxxx.xxxx.xxxx) |
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']] (config-if-hsrp)# mac-address <WORD>
Description: Manually set interface MAC address
Syntax:
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# interface vlan <1-4094> (config-leaf-if)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Configure mac Address
Syntax:
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# interface ethernet <ifRange> (config-leaf-if)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Virtual MAC address
Syntax:
WORD |
MAC address(FORMAT:xxxx.xxxx.xxxx) |
Command Mode: hsrp group : Configure HSRP Group
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# interface ethernet <ifRange> (config-leaf-if)# hsrp group <NUMBER> [['ipv4', 'ipv6']] (config-if-hsrp)# mac-address <WORD>
Description: Enable/disable MAC changes on trunk
Syntax:
accept |
enable |
Command Mode: trunk-portgroup : Configure a trunk port group in the VMWare domain
Command Path:
# configure [['terminal', 't']] (config)# vmware-domain <WORD> [delimiter <WORD>] (config-vmware)# trunk-portgroup <> (config-vmware-trunk)# mac-changes accept
Description: enable/disable mac-learning on the qinq-tunnel
Syntax:
arg |
Command Mode: dot1q-tunnel : Tunnel configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# dot1q-tunnel <WORD> (config-tenant-tunnel)#mac-learning <>
Description: Configure User Precedence
Syntax:
integer-value |
Configure User Precedence |
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# application <WORD> (config-tenant-app)# epg <WORD> [type <WORD>] (config-tenant-app-epg)# match-precedence <integer-value>
Description: Add a rule to match DSCP or DOT1P, queue the traffic and optionally mutate it
Syntax:
dscp |
Match entry for DSCP |
dot1p |
Match entry for DOT1P |
WORD |
From of DSCP or DOT1P range |
WORD |
To of DSCP or DOT1P range |
WORD |
(Optional) Set the QOS class for the traffic |
WORD |
(Optional) DSCP rewrite |
WORD |
(Optional) Dot1P rewrite |
Command Mode: policy-map type qos : QOS policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type qos <WORD> (config-tenant-pmap-qos)# match dscp|dot1p <WORD> <WORD> [set-class <WORD>] [set-dscp <WORD>] [set-cos <WORD>]
Description: Configure match
Syntax:
arg |
Command Mode: flow record : Configure Netflow Record
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# flow record <WORD> (config-tn-flow-record)# match <>
Description: Configure match
Syntax:
arg |
Command Mode: flow record : Configure Netflow Record
Command Path:
# configure [['terminal', 't']] (config)# flow record <WORD> (config-flow-record)# match <>
Description: Match the ARP traffic
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# access-list <WORD> (config-tenant-acl)# match arp
Description: Match subnets of a bridge-domain
Syntax:
arg |
|
tenant |
(Optional) Tenant name |
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>]
Description: Match subnets of a bridge-domain
Syntax:
arg |
|
tenant |
(Optional) Tenant name |
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match bridge-domain <> [tenant <tenant>]
Description: Match DSCP traffic
Syntax:
<0-64> |
DSCP Value |
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# access-list <WORD> (config-tenant-acl)# match dscp <0-64>
Description: Match the ICMP traffic
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# access-list <WORD> (config-tenant-acl)# match icmp
Description: Match the IP traffic
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# access-list <WORD> (config-tenant-acl)# match ip
Description: Add a subnet that identify hosts being part of the epg
Syntax:
A.B.C.D/LEN |
IP prefix and network mask length |
shared |
(Optional) Add the shared scope to the existing scope for the subnet |
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>] (config-tenant-l3ext-epg)# match ip <A.B.C.D/LEN> [shared]
Description: Multicast Group prefix
Syntax:
A.B.C.D/LEN |
IPv4 group prefix and network mask length |
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry> (config-tenant-rtmap)# match ip multicast group <A.B.C.D/LEN>
Description: Rendezvous point prefix
Syntax:
A.B.C.D/LEN |
IPv4 group prefix and network mask length |
A.B.C.D/LEN |
IPv4 Rendezvous point prefix and network mask length |
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry> (config-tenant-rtmap)# match ip multicast group <A.B.C.D/LEN> rp <A.B.C.D/LEN>
Description: source prefix
Syntax:
A.B.C.D/LEN |
IPv4 group prefix and network mask length |
A.B.C.D/LEN |
IPv4 Rendezvous point prefix and network mask length |
A.B.C.D/LEN |
IPv4 source prefix and network mask length |
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry> (config-tenant-rtmap)# match ip multicast group <A.B.C.D/LEN> rp <A.B.C.D/LEN> source <A.B.C.D/LEN>
Description: source prefix
Syntax:
A.B.C.D/LEN |
IPv4 group prefix and network mask length |
A.B.C.D/LEN |
IPv4 source prefix and network mask length |
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry> (config-tenant-rtmap)# match ip multicast group <A.B.C.D/LEN> source <A.B.C.D/LEN>
Description: Rendezvous point prefix
Syntax:
A.B.C.D/LEN |
IPv4 group prefix and network mask length |
A.B.C.D/LEN |
IPv4 source prefix and network mask length |
A.B.C.D/LEN |
IPv4 Rendezvous point prefix and network mask length |
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry> (config-tenant-rtmap)# match ip multicast group <A.B.C.D/LEN> source <A.B.C.D/LEN> rp <A.B.C.D/LEN>
Description: Rendezvous point prefix
Syntax:
A.B.C.D/LEN |
IPv4 Rendezvous point prefix and network mask length |
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry> (config-tenant-rtmap)# match ip multicast rp <A.B.C.D/LEN>
Description: Multicast Group prefix
Syntax:
A.B.C.D/LEN |
IPv4 Rendezvous point prefix and network mask length |
A.B.C.D/LEN |
IPv4 group prefix and network mask length |
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry> (config-tenant-rtmap)# match ip multicast rp <A.B.C.D/LEN> group <A.B.C.D/LEN>
Description: source prefix
Syntax:
A.B.C.D/LEN |
IPv4 Rendezvous point prefix and network mask length |
A.B.C.D/LEN |
IPv4 group prefix and network mask length |
A.B.C.D/LEN |
IPv4 source prefix and network mask length |
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry> (config-tenant-rtmap)# match ip multicast rp <A.B.C.D/LEN> group <A.B.C.D/LEN> source <A.B.C.D/LEN>
Description: Multicast Group prefix
Syntax:
A.B.C.D/LEN |
IPv4 Rendezvous point prefix and network mask length |
A.B.C.D/LEN |
IPv4 source prefix and network mask length |
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry> (config-tenant-rtmap)# match ip multicast rp <A.B.C.D/LEN> source <A.B.C.D/LEN>
Description: Multicast Group prefix
Syntax:
A.B.C.D/LEN |
IPv4 Rendezvous point prefix and network mask length |
A.B.C.D/LEN |
IPv4 source prefix and network mask length |
A.B.C.D/LEN |
IPv4 group prefix and network mask length |
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry> (config-tenant-rtmap)# match ip multicast rp <A.B.C.D/LEN> source <A.B.C.D/LEN> group <A.B.C.D/LEN>
Description: Multicast Group prefix
Syntax:
A.B.C.D/LEN |
IPv4 source prefix and network mask length |
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry> (config-tenant-rtmap)# match ip multicast source <A.B.C.D/LEN>
Description: Multicast Group prefix
Syntax:
A.B.C.D/LEN |
IPv4 source prefix and network mask length |
A.B.C.D/LEN |
IPv4 group prefix and network mask length |
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry> (config-tenant-rtmap)# match ip multicast source <A.B.C.D/LEN> group <A.B.C.D/LEN>
Description: Rendezvous point prefix
Syntax:
A.B.C.D/LEN |
IPv4 source prefix and network mask length |
A.B.C.D/LEN |
IPv4 group prefix and network mask length |
A.B.C.D/LEN |
IPv4 Rendezvous point prefix and network mask length |
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry> (config-tenant-rtmap)# match ip multicast source <A.B.C.D/LEN> group <A.B.C.D/LEN> rp <A.B.C.D/LEN>
Description: Rendezvous point prefix
Syntax:
A.B.C.D/LEN |
IPv4 source prefix and network mask length |
A.B.C.D/LEN |
IPv4 Rendezvous point prefix and network mask length |
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry> (config-tenant-rtmap)# match ip multicast source <A.B.C.D/LEN> rp <A.B.C.D/LEN>
Description: Multicast Group prefix
Syntax:
A.B.C.D/LEN |
IPv4 source prefix and network mask length |
A.B.C.D/LEN |
IPv4 Rendezvous point prefix and network mask length |
A.B.C.D/LEN |
IPv4 group prefix and network mask length |
Command Mode: route-map : Configure route-map
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# route-map <WORD> deny|permit <Sequence to insert to/delete from existing route-map entry> (config-tenant-rtmap)# match ip multicast source <A.B.C.D/LEN> rp <A.B.C.D/LEN> group <A.B.C.D/LEN>
Description: Add a subnet that identify hosts being part of the epg
Syntax:
X:X:X:X::X/<0-128> |
IPv6 prefix and network mask length |
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>] (config-tenant-l3ext-epg)# match ipv6 X:X:X:X::X/<0-128>
Description: Match entries of a prefix-list
Syntax:
WORD |
Name of prefix-list (Max Size 63) |
deny |
(Optional) Reject routes on match |
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match prefix-list <WORD> [deny]
Description: Match entries of a prefix-list
Syntax:
WORD |
Name of prefix-list (Max Size 63) |
deny |
(Optional) Reject routes on match |
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match prefix-list <WORD> [deny]
Description: Specify a raw vzEntry
Syntax:
WORD |
Entry Name (Max Size 64) |
tcpRules |
(Optional) TCP Flags as comma separated values like val1,val2,..valN |
arpOpc |
(Optional) ARP Opcodes |
applyToFrag |
(Optional) Apply to Fragment |
<0-65535> |
(Optional) L4 Destination Port. Number range from=0 to=65535 |
<0-255> |
(Optional) IP Protocol. Number range from=0 to=255 |
icmpv4T |
(Optional) ICMP Type |
stateful |
(Optional) Stateful flag |
icmpv6T |
(Optional) ICMPv6 Type |
<0-65535> |
(Optional) L4 Source Port. Number range from=0 to=65535 |
etherT |
(Optional) Ethernet Type |
<0-65535> |
(Optional) L4 Source Port. Number range from=0 to=65535 |
<0-65535> |
(Optional) L4 Destination Port. Number range from=0 to=65535 |
<0-64> |
(Optional) DSCP Value |
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# access-list <WORD> (config-tenant-acl)# match raw <WORD> [tcpRules <tcpRules>] [arpOpc <arpOpc>] [applyToFrag <applyToFrag>] [dToPort <NUMBER>] [prot <NUMBER>] [icmpv4T <icmpv4T>] [stateful <stateful>] [icmpv6T <icmpv6T>] [sToPort <NUMBER>] [etherT <etherT>] [sFromPort <NUMBER>] [dFromPort <NUMBER>] [matchDscp <0-64>]
Description: Route group
Syntax:
arg |
|
order |
(Optional) Relative order for the entry. Number range from=0 to=9 |
deny |
(Optional) Reject routes on match |
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match route group <> [order <order>] [deny]
Description: Route group
Syntax:
arg |
|
order |
(Optional) Relative order for the entry. Number range from=0 to=9 |
deny |
(Optional) Reject routes on match |
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match route group <> [order <order>] [deny]
Description: Match TCP traffic
Syntax:
<from>-[<to>] contained in <0-65535> |
(Optional) TCP Source port Range |
<from>-[<to>] contained in <0-65535> |
(Optional) TCP Destination port Range |
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# access-list <WORD> (config-tenant-acl)# match tcp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>] contained in <0-65535>]
Description: Match UDP traffic
Syntax:
<from>-[<to>] contained in <0-65535> |
(Optional) UDP Source port Range |
<from>-[<to>] contained in <0-65535> |
(Optional) UDP Destination port Range |
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# access-list <WORD> (config-tenant-acl)# match udp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>] contained in <0-65535>]
Description: Feature to limit the number of non-self-originated LSAs
Syntax:
<1-4294967295> |
Set maximum number of non self-generated LSAs. Number range from=1 to=4294967295 |
<1-100> |
Threshold value (%) at which to generate a warning message. Number range from=1 to=100 |
reject |
Reject LSAs beyond the limit |
restart |
Restart the neighbor |
log |
log a warning |
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template ospf vrf-policy <WORD> tenant <WORD> (config-vrf-policy)# max-lsa <NUMBER> <NUMBER> reject|restart|log
Description: Feature to limit the number of non-self-originated LSAs
Syntax:
<1-4294967295> |
Set maximum number of non self-generated LSAs. Number range from=1 to=4294967295 |
<1-100> |
Threshold value (%) at which to generate a warning message. Number range from=1 to=100 |
reject |
Reject LSAs beyond the limit |
restart |
Restart the neighbor |
log |
log a warning |
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# template ospf vrf-policy <WORD> tenant <WORD> (config-vrf-policy)# max-lsa <NUMBER> <NUMBER> reject|restart|log
Description: Set The maximum validity period for a webtoken
Syntax:
<4-24> |
Set The maximum validity period for a webtoken. Number range from=4 to=24 |
Command Mode: crypto webtoken : The cryptographic data used for generating and verifying web tokens.
Command Path:
# configure [['terminal', 't']] (config)# crypto webtoken (config-webtoken)# max-validity-period <NUMBER>
Description: Set the window maximum concurrent node limit
Syntax:
nodes |
Maximum number of tasks that can be processed concurrently. |
<0-65535> |
Enter maximum number of concurrent nodes. 0 for unlimited. Number range from=0 to=65535 |
Command Mode: absolute : Absolute window configuration mode
Command Path:
# configure [['terminal', 't']] (config)# scheduler fabric|controller schedule <WORD> (config-scheduler)# absolute window <WORD> (config-scheduler-absolute)# max concurrent nodes <NUMBER>
Description: Set the window maximum concurrent node limit
Syntax:
nodes |
Maximum number of tasks that can be processed concurrently. |
<0-65535> |
Enter maximum number of concurrent nodes. 0 for unlimited. Number range from=0 to=65535 |
Command Mode: recurring : Recurring window configuration mode
Command Path:
# configure [['terminal', 't']] (config)# scheduler fabric|controller schedule <WORD> (config-scheduler)# recurring window <WORD> (config-scheduler-recurring)# max concurrent nodes <NUMBER>
Description: Set the window maximum running time
Syntax:
time |
Maximum running time |
TIME |
Enter the maximum running time in dd:hh:mm:ss. 0 for unlimited |
Command Mode: absolute : Absolute window configuration mode
Command Path:
# configure [['terminal', 't']] (config)# scheduler fabric|controller schedule <WORD> (config-scheduler)# absolute window <WORD> (config-scheduler-absolute)# max running time <TIME>
Description: Set the window maximum running time
Syntax:
time |
Maximum running time in milliseconds |
TIME |
Enter the maximum running time in dd:hh:mm:ss. 0 for unlimited |
Command Mode: recurring : Recurring window configuration mode
Command Path:
# configure [['terminal', 't']] (config)# scheduler fabric|controller schedule <WORD> (config-scheduler)# recurring window <WORD> (config-scheduler-recurring)# max running time <TIME>
Description: Configure BGP Maximum AS limit
Syntax:
<0-2000> |
BGP Maximum AS limit. Number range from=0 to=2000 |
Command Mode: template bgp timers : Configure Router BGP Timer Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template bgp timers <WORD> tenant <WORD> (config-bgp-timers)# maxas-limit <NUMBER>
Description: Configure BGP Maximum AS limit
Syntax:
<0-2000> |
BGP Maximum AS limit. Number range from=0 to=2000 |
Command Mode: template bgp timers : Configure Router BGP Timer Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# template bgp timers <WORD> tenant <WORD> (config-bgp-timers)# maxas-limit <NUMBER>
Description: Set the maximum ECMP for the OSPF protocol
Syntax:
<1-64> |
Maximum paths. Number range from=1 to=64 |
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template ospf vrf-policy <WORD> tenant <WORD> (config-vrf-policy)# maximum-paths <NUMBER>
Description: Set EIGRP Maximum Path Limit
Syntax:
<1-16> |
Maximum Path Limit. Number range from=1 to=16 |
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD> (config-template-eigrp-vrf-pol)# maximum-paths <NUMBER>
Description: Set EIGRP Maximum Path Limit
Syntax:
<1-16> |
Maximum Path Limit. Number range from=1 to=16 |
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# router eigrp default (config-eigrp)# vrf member tenant <WORD> vrf <WORD> (config-eigrp-vrf)# address-family ipv4|ipv6 unicast (config-address-family)# maximum-paths <NUMBER>
Description: Set the maximum ECMP for the OSPF protocol
Syntax:
<1-64> |
Maximum paths. Number range from=1 to=64 |
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# template ospf vrf-policy <WORD> tenant <WORD> (config-vrf-policy)# maximum-paths <NUMBER>
Description: Set EIGRP Maximum Path Limit
Syntax:
<1-16> |
Maximum Path Limit. Number range from=1 to=16 |
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# template eigrp vrf-policy <WORD> tenant <WORD> (config-template-eigrp-vrf-pol)# maximum-paths <NUMBER>
Description: Set EIGRP Maximum Path Limit
Syntax:
<1-16> |
Maximum Path Limit. Number range from=1 to=16 |
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# router eigrp default (config-eigrp)# vrf member tenant <WORD> vrf <WORD> (config-eigrp-vrf)# address-family ipv4|ipv6 unicast (config-address-family)# maximum-paths <NUMBER>
Description: Maximum number of prefixes from this neighbor
Syntax:
<1-300000> |
Max. prefix limit. Number range from=1 to=300000 |
<action> |
(Optional) Action to be performed when the maximum prefix limit is reached |
<1-100> |
(Optional) The threshold % of the maximum number of prefixes before a warning is issued. Number range from=1 to=100 |
<1-65535> |
(Optional) The period of time in minutes before restarting the peer when the prefix limit is reached. Number range from=1 to=65535 |
Command Mode: address-family : Configure an address-family for peer
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# router bgp <fabric-ASN> (config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD> (config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out <WORD>] (config-leaf-bgp-vrf-neighbor)# address-family ipv4|ipv6|l2vpn unicast|evpn (config-leaf-bgp-vrf-neighbor-af)# maximum-prefix <NUMBER> [action <action>] [threshold <NUMBER>] [restart-time <NUMBER>]
Description: Maximum number of prefixes from this neighbor
Syntax:
<1-300000> |
Max. prefix limit. Number range from=1 to=300000 |
<action> |
(Optional) Action to be performed when the maximum prefix limit is reached |
<1-100> |
(Optional) The threshold % of the maximum number of prefixes before a warning is issued. Number range from=1 to=100 |
<1-65535> |
(Optional) The period of time in minutes before restarting the peer when the prefix limit is reached. Number range from=1 to=65535 |
Command Mode: address-family : Configure an address-family for peer
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# router bgp <fabric-ASN> (config-leaf-bgp)# vrf member tenant <WORD> vrf <WORD> (config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [evpn] [l3out <WORD>] (config-leaf-bgp-vrf-neighbor)# address-family ipv4|ipv6|l2vpn unicast|evpn (config-leaf-bgp-vrf-neighbor-af)# maximum-prefix <NUMBER> [action <action>] [threshold <NUMBER>] [restart-time <NUMBER>]
Description: Configure MCP interface parameters
Syntax:
enable |
Configure MCP parameters |
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']] (config)# template policy-group <WORD> (config-pol-grp-if)# mcp enable
Description: Configure MCP interface parameters
Syntax:
enable |
Configure MCP parameters |
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']] (config)# template port-channel <WORD> (config-po-ch-if)# mcp enable
Description: Configure MCP interface parameters
Syntax:
enable |
Configure MCP parameters |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# mcp enable
Description: Configure MCP interface parameters
Syntax:
enable |
Configure MCP parameters |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# mcp enable
Description: Configure MCP interface parameters
Syntax:
enable |
Configure MCP parameters |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# interface ethernet <ifRange> (config-leaf-if)# mcp enable
Description: Configure MCP interface parameters
Syntax:
enable |
Configure MCP parameters |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# mcp enable
Description: Configure MCP interface parameters
Syntax:
enable |
Configure MCP parameters |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# mcp enable
Description: Configure MCP Loop Protection Action
Syntax:
port-disable |
Disable the port when MCP detects loop |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# mcp action port-disable
Description: Configure MCP State Control To Pdu-per-vlan
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# mcp control pdu-per-vlan
Description: Update description for MCP policy
Syntax:
<description> |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# mcp description <description>
Description: Enable/Disable MCP Protocol
Syntax:
key |
Configure MCP key |
WORD |
MCP key |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# mcp enable key <WORD>
Description: Configure MCP Loop Detection Factor
Syntax:
<1-255> |
MCP Loop Detection Multipication Factor. Number range from=1 to=255 |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# mcp factor <NUMBER>
Description: Configure MCP Loop Detection Init Delay Time
Syntax:
<0-1800> |
MCP Loop Detection Init Delay Time. Number range from=0 to=1800 |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# mcp init-delay <NUMBER>
Description: Configure MCP Advertisement Transmit Frequency
Syntax:
<2-300> |
MCP Advertisement Tx Frequency. Number range from=2 to=300 |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# mcp transmit-frequency <NUMBER>
Description: Configure Cluster Interface Member
Syntax:
device |
Cluster Device |
WORD |
Cluster Device name (Max Size 64) |
device-interface |
Cluster Device Interface |
WORD |
Cluster Device Interface (Max Size 256) |
Command Mode: cluster-interface : Configure L4-L7 Cluster Interface
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service <service>] [function <function>] [context <context>] [trunking <enable|disable>] (config-cluster)# cluster-interface <WORD> [vlan <NUMBER>] (config-cluster-interface)# member device <WORD> device-interface <WORD>
Description: Configure the urgency of the message
Syntax:
info |
Info |
notice |
Notice |
emergency |
Emergency |
alert |
Alert |
critical |
Critical |
error |
Error |
debug |
Debug |
warning |
Warning |
Command Mode: destination : Configure destination Parameters
Command Path:
# configure [['terminal', 't']] (config)# callhome common (config-callhome)# destination-profile (config-callhome-destnprof)# destination <WORD> (config-callhome-destnprof-destn)# message-level info|notice|emergency|alert|critical|error|debug|warning
Description: Configure the size of the message
Syntax:
<size> |
The size of the messages. Number range from=0 to=5000000 |
Command Mode: destination : Configure destination Parameters
Command Path:
# configure [['terminal', 't']] (config)# callhome common (config-callhome)# destination-profile (config-callhome-destnprof)# destination <WORD> (config-callhome-destnprof-destn)# message-size <NUMBER>
Description: Set EIGRP Metric Style
Syntax:
version |
Metric Style |
64bit |
wide metric |
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD> (config-template-eigrp-vrf-pol)# metric version 64bit
Description: Set EIGRP Metric Style
Syntax:
version |
Metric Style |
64bit |
wide metric |
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# router eigrp default (config-eigrp)# vrf member tenant <WORD> vrf <WORD> (config-eigrp-vrf)# address-family ipv4|ipv6 unicast (config-address-family)# metric version 64bit
Description: Set EIGRP Metric Style
Syntax:
version |
Metric Style |
64bit |
wide metric |
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# template eigrp vrf-policy <WORD> tenant <WORD> (config-template-eigrp-vrf-pol)# metric version 64bit
Description: Set EIGRP Metric Style
Syntax:
version |
Metric Style |
64bit |
wide metric |
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# router eigrp default (config-eigrp)# vrf member tenant <WORD> vrf <WORD> (config-eigrp-vrf)# address-family ipv4|ipv6 unicast (config-address-family)# metric version 64bit
Description: Set Mgmt Connectivity Preference
Syntax:
inband |
Set to inband |
ooband |
Set to outband |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# mgmt-connectivity-pref inband|ooband
Description: Select remote path management EPG
Syntax:
in-band |
In-Band EPG |
out-of-band |
Out-of-Band EPG |
WORD |
Management EPG name |
Command Mode: remote : Remote path configuration mode
Command Path:
# configure [['terminal', 't']] (config)# remote path <WORD> (config-remote)# mgmt-epg in-band|out-of-band <WORD>
Description: Create a VMM Microsoft Domain
Syntax:
WORD |
VMM Microsoft Domain name |
WORD |
(Optional) Custom Delimiter |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# microsoft-domain <WORD> [delimiter <WORD>]
Description: Associate EPG to a Microsoft Domain
Syntax:
member |
Bind the EPG to a Microsoft domain |
WORD |
Microsoft Domain Name |
WORD |
(Optional) Enforce encap value. (For example vlan-10 or auto) |
WORD |
(Optional) Deployment mode |
WORD |
(Optional) Push mode |
WORD |
(Optional) Custom Delimiter |
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# application <WORD> (config-tenant-app)# epg <WORD> [type <WORD>] (config-tenant-app-epg)# microsoft-domain member <WORD> [encap <WORD>] [deploy <WORD>] [push <WORD>] [delimiter <WORD>]
Description: Configure static IP pool
Syntax:
static-ip-pool |
Configure the static IP pool |
name |
enter the name of the static IP pool |
gateway |
Configure gateway address on interface |
gwAddress |
gwAddress |
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# application <WORD> (config-tenant-app)# epg <WORD> [type <WORD>] (config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>
Description: Configure BFD MIN-RX value in milliseconds
Syntax:
<interval> |
BFD interval. Number range from=50 to=999 |
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']] (config)# template bfd ip|ipv6 <WORD> (config-bfd)# min-rx <NUMBER>
Description: Configure required Minimum Rx Interval in milliseconds
Syntax:
<interval> |
Minimum Rx Interval. Number range from=50 to=999 |
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template bfd <WORD> tenant <WORD> (config-template-bfd-pol)# min-rx <NUMBER>
Description: Configure required Minimum Rx Interval in milliseconds
Syntax:
<interval> |
Minimum Rx Interval. Number range from=50 to=999 |
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# template bfd <WORD> tenant <WORD> (config-template-bfd-pol)# min-rx <NUMBER>
Description: Configure BFD MIN-TX value in milliseconds
Syntax:
<interval> |
BFD interval. Number range from=50 to=999 |
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']] (config)# template bfd ip|ipv6 <WORD> (config-bfd)# min-tx <NUMBER>
Description: Configure required Minimum Tx Interval in milliseconds
Syntax:
<interval> |
Minimum Tx Interval. Number range from=50 to=999 |
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template bfd <WORD> tenant <WORD> (config-template-bfd-pol)# min-tx <NUMBER>
Description: Configure required Minimum Tx Interval in milliseconds
Syntax:
<interval> |
Minimum Tx Interval. Number range from=50 to=999 |
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# template bfd <WORD> tenant <WORD> (config-template-bfd-pol)# min-tx <NUMBER>
Description: Set the minimum number of buffer of MTU size to be reserved
Syntax:
buffer |
Number of minim buffers to reserve |
<0-3> |
Number of minim buffers to reserve |
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']] (config)# qos parameters level1|level2|level3 (config-qos)# min buffer <0-3>
Description: Snapshot import mode atomic|best-effort
Syntax:
atomic |
Atomic mode |
best-effort |
Best Effort mode |
Command Mode: snapshot import : Configuration import setup mode
Command Path:
# configure [['terminal', 't']] (config)# snapshot import <WORD> (config-import)# mode atomic|best-effort
Description: Configure Node Control Mode
Syntax:
None |
Disable Dom (Digital Optical Monitoring) |
Dom |
Enable Dom (Digital Optical Monitoring |
Command Mode: node-control : Create a Node Control Policy
Command Path:
# configure [['terminal', 't']] (config)# node-control policy <WORD> (config-node)# mode None|Dom
Description: Set the length of the encryption keys
Syntax:
<modulus> |
<modulus> |
Command Mode: crypto keyring : A keyring mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']] (config)# crypto keyring <WORD> (config-keyring)# modulus <modulus>
Description: Configure a monitor session
Syntax:
virtual |
virtual |
session |
session |
WORD |
session name (Max Size 64) |
Command Mode: configure-avs : Configure a VMWare Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']] (config)# vmware-domain <WORD> [delimiter <WORD>] (config-vmware)# configure-avs (config-vmware-avs)# monitor virtual session <WORD>
Description: Configue monitor session for access interfaces
Syntax:
session |
session |
session_name |
session name (Max Size 59) |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# monitor access session <session_name>
Description: Configue monitor session for fabric interfaces
Syntax:
session |
session |
session_name |
session name (Max Size 59) |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# monitor fabric session <session_name>
Description: Configue monitor session for tenant EPGs
Syntax:
tenant_name |
tenant name (Max Size 63) |
session |
session |
WORD |
session name (Max Size 59) |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# monitor tenant <tenant_name> session <WORD>
Description: Configure monitor session for virtual switches
Syntax:
session |
session |
WORD |
Session name (Max Size 64) |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# monitor virtual session <WORD>
Description: Disable OSPF MTU mismatch detection
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template ospf interface-policy <WORD> tenant <WORD> (config-interface-policy)# mtu-ignore
Description: Disable OSPF MTU mismatch detection
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# template ospf interface-policy <WORD> tenant <WORD> (config-interface-policy)# mtu-ignore
Description: Set the MTU for this class of service
Syntax:
<1500-9216> |
MTU value |
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']] (config)# qos parameters level1|level2|level3 (config-qos)# mtu <1500-9216>
Description: Set the interface Maximum Transmission Unit (MTU)
Syntax:
<576-9000> |
Interface MTU. Number range from=576 to=9000 |
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface vlan <1-4094> (config-leaf-if)# mtu <NUMBER>
Description: Set the interface Maximum Transmission Unit (MTU)
Syntax:
<576-9000> |
Interface MTU. Number range from=576 to=9000 |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# mtu <NUMBER>
Description: Set the interface Maximum Transmission Unit (MTU)
Syntax:
<576-9000> |
Interface MTU. Number range from=576 to=9000 |
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# interface vlan <1-4094> (config-leaf-if)# mtu <NUMBER>
Description: Set the interface Maximum Transmission Unit (MTU)
Syntax:
<576-9000> |
Interface MTU. Number range from=576 to=9000 |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# interface ethernet <ifRange> (config-leaf-if)# mtu <NUMBER>
Description: Update MTU value in Netflow Node-policy
Syntax:
arg |
Configure MTU value in Netflow Node-policy. Number range from=576 to=9216 |
Command Mode: flow node-policy : Configure Netflow Node Policy Parameters
Command Path:
# configure [['terminal', 't']] (config)# flow node-policy <WORD> (config-flow-node-pol)# mtu <>
Description: MTU size
Syntax:
mtu |
mtu value. Number range from=64 to=9216 |
Command Mode: destination tenant : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']] (config)# monitor access session <session_name> (config-monitor-access)# destination tenant <tenant_name> application <application_name> epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M> (config-monitor-access-dest)# mtu <mtu>
Description: MTU size
Syntax:
mtu |
mtu value. Number range from=64 to=9216 |
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']] (config)# monitor fabric session <session_name> (config-monitor-fabric)# destination tenant <tenant_name> application <application_name> epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M> (config-monitor-fabric-dest)# mtu <mtu>
Description: MTU size
Syntax:
arg |
mtu value. Number range from=64 to=9216 |
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']] (config)# monitor tenant <tenant_name> session <WORD> (config-monitor-tenant)# destination tenant <tenant_name> application <application_name> epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M> (config-monitor-tenant-dest)# mtu <>
Description: Configure MTU size
Syntax:
arg |
MTU value. Number range from=64 to=9216 |
Command Mode: destination destip : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']] (config)# monitor virtual session <WORD> (config-monitor-virtual)# destination destip <A.B.C.D> (config-monitor-virtual-remote-dest)# mtu <>
Description: Change behavior for multi destination flood
Syntax:
WORD |
Unknown multicast MAC and Broadcast handling |
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# bridge-domain <WORD> (config-tenant-bd)# multi-destination <WORD>
Description: Configure multi-site MAC address
Syntax:
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# interface bridge-domain <WORD> (config-tenant-interface)# multi-site-mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Configure outgoing multicast IP address for VXLAN modes
Syntax:
IP |
Multicast IP |
Command Mode: configure-avs : Configure a VMWare Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']] (config)# vmware-domain <WORD> [delimiter <WORD>] (config-vmware)# configure-avs (config-vmware-avs)# multicast-address <IP>
Description: Configure BFD MULTIPLIER value
Syntax:
<interval> |
BFD interval. Number range from=1 to=50 |
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']] (config)# template bfd ip|ipv6 <WORD> (config-bfd)# multiplier <NUMBER>
Description: Configure detection multiplier
Syntax:
<interval> |
Detection multiplier. Number range from=1 to=50 |
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template bfd <WORD> tenant <WORD> (config-template-bfd-pol)# multiplier <NUMBER>
Description: Configure detection multiplier
Syntax:
<interval> |
Detection multiplier. Number range from=1 to=50 |
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# spine <101-4000> (config-spine)# template bfd <WORD> tenant <WORD> (config-template-bfd-pol)# multiplier <NUMBER>