- Index
- Preface
- Using the Command-Line Interface
- Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter Cisco IOS Commands - aaa accounting through renew ip
- Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter Cisco IOS Commands - rmon collection through show vtp
- Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter Cisco IOS Commands - shutdown through vtp
- Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter Boot Loader Commands
- Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter Debug Commands
- Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter Show Platform Commands
Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter Command Reference, Release 12.2(40)EX2
Bias-Free Language
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
- Updated:
- February 15, 2018
Chapter: Index
A -
B -
C -
D -
E -
F -
G -
H -
I -
J -
L -
M -
N -
O -
P -
Q -
R -
S -
T -
U -
V -
EtherChannel
IGMP snooping
MSTP
port-based authentication
QoS
QoS
QoS
STP
VLANs
VTP
Index
A
aaa accounting dot1x command 2-1
aaa authentication dot1x command 2-3
aaa authorization network command 2-5
AAA methods 2-3
abort command 2-740
access control entries
access control lists
access groups
IP 2-136
MAC, displaying 2-509
access list, IPv6 2-201
access map configuration mode 2-258
access mode 2-682
access ports 2-682
ACLs
deny 2-78
displaying 2-374
for non-IP protocols 2-238
IP 2-136
matching 2-258
on Layer 2 interfaces 2-136
permit 2-324
action command 2-6
aggregate-port learner 2-313
allowed VLANs 2-702
apply command 2-740
archive copy-sw command 2-8
archive download-sw command 2-11
archive tar command 2-15
archive upload-sw command 2-18
arp access-list command 2-20
authentication failed VLAN
auth-fail max-attempts
See dot1x auth-fail max-attempts
auth-fail vlan
authorization state of controlled port 2-111
autonegotiation of duplex mode 2-117
auto qos voip command 2-22
B
BackboneFast, for STP 2-609
backup interfaces
configuring 2-677
displaying 2-436
boot (boot loader) command A-2
boot auto-copy-sw command 2-26
boot auto-download-sw command 2-27
boot config-file command 2-29
boot enable-break command 2-30
boot helper command 2-31
boot helper-config file command 2-32
booting
Cisco IOS image 2-35
displaying environment variables 2-383
interrupting 2-30
manually 2-33
boot loader
accessing A-1
booting
Cisco IOS image A-2
helper image 2-31
directories
creating A-15
displaying a list of A-7
removing A-19
displaying
available commands A-12
memory heap utilization A-13
version A-26
environment variables
described A-20
displaying settings A-20
location of A-21
setting A-20
unsetting A-24
files
copying A-5
deleting A-6
displaying a list of A-7
displaying the contents of A-4, A-16, A-23
renaming A-17
file system
formatting A-10
initializing flash A-9
running a consistency check A-11
prompt A-1
resetting the system A-18
boot manual command 2-33
boot private-config-file command 2-34
boot system command 2-35
BPDU filtering, for spanning tree 2-610, 2-644
BPDU guard, for spanning tree 2-612, 2-644
broadcast storm control 2-665
C
cat (boot loader) command A-4
CDP, enabling protocol tunneling for 2-219
channel-group command 2-37
channel-protocol command 2-41
Cisco SoftPhone
auto-QoS configuration 2-22
trusting packets sent from 2-299
class command 2-42
class-map command 2-44
class maps
creating 2-44
defining the match criteria 2-260
displaying 2-388
class of service
clear dot1x command 2-46
clear eap command 2-47
clear errdisable interface 2-48
clear ip arp inspection log command 2-49
clear ip arp inspection statistics command 2-50
clear ipc command 2-53
clear ip dhcp snooping database command 2-51
clear l2protocol-tunnel counters command 2-54
clear lacp command 2-55
clear logging command 2-56
clear mac address-table command 2-57, 2-58
clear pagp command 2-59
clear port-security command 2-60
clear spanning-tree counters command 2-62
clear spanning-tree detected-protocols command 2-63
clear vmps statistics command 2-64
clear vtp counters command 2-65
command modes defined 1-2
configuration files
password recovery disable considerations A-1
specifying the name 2-29, 2-34
configuring multiple interfaces 2-132
config-vlan mode
commands 2-726
description 1-5
entering 2-725
summary 1-2
copy (boot loader) command A-5
copy logging onboard command 2-66
CoS
assigning default value to incoming packets 2-269
assigning to Layer 2 protocol packets 2-222
overriding the incoming value 2-269
CoS-to-DSCP map 2-273
CPU ASIC statistics, displaying 2-389
crashinfo files 2-123
D
debug auto qos command B-2
debug backup command B-4
debug dot1x command B-5
debug dtp command B-6
debug eap command B-7
debug etherchannel command B-8
debug fastethernet command B-9
debug interface command B-12
debug ip dhcp snooping command B-10
debug ip igmp filter command B-13
debug ip igmp max-groups command B-14
debug ip igmp snooping command B-15
debug ip verify source packet command B-11
debug lacp command B-16
debug mac-notification command B-17
debug matm command B-18
debug matm move update command B-19
debug monitor command B-20
debug mvrdbg command B-21
debug nvram command B-22
debug pagp command B-23
debug platform acl command B-24
debug platform backup interface command B-26
debug platform cli-redirection main command B-27
debug platform configuration command B-28
debug platform cpu-queues command B-29
debug platform device-manager command B-31
debug platform dot1x command B-32
debug platform etherchannel command B-33
debug platform fallback-bridging command B-34
debug platform forw-tcam command B-35
debug platform ip arp inspection command B-36
debug platform ipc command B-45
debug platform ip dhcp command B-37
debug platform ip igmp snooping command B-38
debug platform ip multicast command B-40
debug platform ip unicast command B-42
debug platform ip wccp command B-44
debug platform led command B-46
debug platform matm command B-47
debug platform messaging application command B-48
debug platform phy command B-50
debug platform pm command B-52
debug platform port-asic command B-54
debug platform port-security command B-55
debug platform qos-acl-tcam command B-56
debug platform remote-commands command B-57
debug platform resource-manager command B-58
debug platform snmp command B-59
debug platform span command B-60
debug platform stack-manager command B-61
debug platform supervisor-asic command B-62
debug platform sw-bridge command B-63
debug platform tcam command B-64
debug platform udld command B-67
debug platform vlan command B-68
debug pm command B-69
debug port-security command B-71
debug qos-manager command B-72
debug spanning-tree backbonefast command B-75
debug spanning-tree bpdu command B-76
debug spanning-tree bpdu-opt command B-77
debug spanning-tree command B-73
debug spanning-tree mstp command B-78
debug spanning-tree switch command B-80
debug spanning-tree uplinkfast command B-82
debug sw-vlan command B-83
debug sw-vlan ifs command B-85
debug sw-vlan notification command B-86
debug sw-vlan vtp command B-88
debug udld command B-90
debug vqpc command B-92
define interface-range command 2-68
delete (boot loader) command A-6
delete command 2-70
deny (ARP access-list configuration) command 2-71
deny (IPv6) command 2-73
deny command 2-78
detect mechanism, causes 2-119
DHCP snooping
accepting untrusted packets from edge switch 2-164
enabling
on a VLAN 2-170
trust on an interface 2-168
error recovery timer 2-121
rate limiting 2-167
DHCP snooping binding database
binding file, configuring 2-160
bindings
adding 2-158
deleting 2-158
displaying 2-455
clearing database agent statistics 2-51
database agent, configuring 2-160
displaying
binding entries 2-455
database agent status 2-457, 2-459
renewing 2-355
dir (boot loader) command A-7
directories, deleting 2-70
dot1x auth-fail max-attempts 2-90
dot1x auth-fail vlan 2-92
dot1x command 2-88
dot1x control-direction command 2-94
dot1x critical global configuration command 2-96
dot1x critical interface configuration command 2-98
dot1x default command 2-100
dot1x fallback command 2-101
dot1x guest-vlan command 2-102
dot1x host-mode command 2-104
dot1x initialize command 2-105
dot1x mac-auth-bypass command 2-106
dot1x max-reauth-req command 2-108
dot1x max-req command 2-109
dot1x pae command 2-110
dot1x port-control command 2-111
dot1x re-authenticate command 2-113
dot1x reauthentication command 2-114
dot1x timeout command 2-115
dropping packets, with ACL matches 2-6
drop threshold, Layer 2 protocol tunneling 2-219
DSCP-to-CoS map 2-273
DSCP-to-DSCP-mutation map 2-273
DTP 2-683
DTP flap
error detection for 2-119
error recovery timer 2-121
DTP negotiation 2-687
dual IPv4 and IPv6 templates 2-319
duplex command 2-117
dynamic-access ports
configuring 2-675
restrictions 2-676
dynamic ARP inspection
ARP ACLs
apply to a VLAN 2-144
define 2-20
deny packets 2-71
display 2-378
permit packets 2-317
clear
log buffer 2-49
statistics 2-50
display
ARP ACLs 2-378
configuration and operating state 2-450
log buffer 2-450
statistics 2-450
trust state and rate limit 2-450
enable per VLAN 2-154
error detection for 2-119
error recovery timer 2-121
log buffer
clear 2-49
configure 2-148
display 2-450
rate-limit incoming ARP packets 2-146
statistics
clear 2-50
display 2-450
trusted interface state 2-150
type of packet logged 2-155
validation checks 2-152
dynamic auto VLAN membership mode 2-682
dynamic desirable VLAN membership mode 2-682
Dynamic Host Configuration Protocol (DHCP)
Dynamic Trunking Protocol
E
EAP-request/identity frame
maximum number to send 2-109
response time before retransmitting 2-115
encapsulation methods 2-702
environment variables, displaying 2-383
errdisable detect cause command 2-119
errdisable recovery command 2-121
error conditions, displaying 2-424
error disable detection 2-119
error-disabled interfaces, displaying 2-436
EtherChannel
assigning Ethernet interface to channel group 2-37
creating port-channel logical interface 2-130
debug EtherChannel/PAgP, display B-8
debug platform-specific events, display B-33
displaying 2-427
enabling Layer 2 protocol tunneling for
LACP 2-220
PAgP 2-220
UDLD 2-220
interface information, displaying 2-436
LACP
clearing channel-group information 2-55, 2-56
debug messages, display B-16
displaying 2-495
modes 2-37
port priority for hot-standby ports 2-223
restricting a protocol 2-41
system priority 2-225
load-distribution methods 2-335
PAgP
aggregate-port learner 2-313
clearing channel-group information 2-59
debug messages, display B-23
displaying 2-554
error detection for 2-119
error recovery timer 2-121
learn method 2-313
modes 2-37
physical-port learner 2-313
priority of interface for transmitted traffic 2-315
Ethernet controller, internal register display 2-391, 2-398
Ethernet Management port, debugging B-9
Ethernet statistics, collecting 2-357
exception crashinfo command 2-123, 2-128
exit command 2-740
extended-range VLANs
and allowed VLAN list 2-702
and pruning-eligible list 2-702
configuring 2-725
extended system ID for STP 2-618
F
fallback profile command 2-124
fallback profiles, displaying 2-430
fan information, displaying 2-420
file name, VTP 2-751
files, deleting 2-70
flash_init (boot loader) command A-9
Flex Links
configuring 2-677
displaying 2-436
flowcontrol command 2-126
format (boot loader) command A-10
forwarding packets, with ACL matches 2-6
forwarding results, display C-9
frame forwarding information, displaying C-9
front-end controller counter and status information C-11
fsck (boot loader) command A-11
G
global configuration mode 1-2, 1-4
H
hardware ACL statistics 2-374
health monitoring diagnostic tests 2-81
help (boot loader) command A-12
hierarchical policy maps 2-333
host connection, port configuration 2-681
host ports, private VLANs 2-685
I
IEEE 802.1Q trunk ports and native VLANs 2-742
IEEE 802.1Q tunnel ports
configuring 2-682
displaying 2-410
limitations 2-683
IEEE 802.1x
and switchport modes 2-683
violation error recovery 2-121
See also port-based authentication
IGMP filters
applying 2-173
debug messages, display B-13
IGMP groups, setting maximum 2-175
IGMP maximum groups, debugging B-14
IGMP profiles
creating 2-177
displaying 2-462
IGMP snooping
adding ports as a static member of a group 2-193
displaying 2-463, 2-468, 2-470
enabling 2-179
enabling the configurable-leave timer 2-181
enabling the Immediate-Leave feature 2-190
flooding query count 2-187
interface topology change notification behavior 2-189
multicast table 2-466
querier 2-183
query solicitation 2-187
report suppression 2-185
switch topology change notification behavior 2-187
images
Immediate-Leave processing
IGMP 2-190
IPv6 2-215
MVR 2-309
interface configuration mode 1-2, 1-4
interface port-channel command 2-130
interface range command 2-132
interface-range macros 2-68
interfaces
assigning Ethernet interface to channel group 2-37
configuring 2-117
configuring multiple 2-132
creating port-channel logical 2-130
debug messages, display B-12
disabling 2-597
displaying the MAC address table 2-521
restarting 2-597
interface speed, configuring 2-655
interface vlan command 2-134
internal registers, displaying 2-391, 2-398, 2-401
Internet Group Management Protocol
ip access-group command 2-136
ip address command 2-139
IP addresses, setting 2-139
IP address matching 2-258
ip admission command 2-141
ip admission name proxy http command 2-142
ip arp inspection filter vlan command 2-144
ip arp inspection limit command 2-146
ip arp inspection log-buffer command 2-148
ip arp inspection trust command 2-150
ip arp inspection validate command 2-152
ip arp inspection vlan command 2-154
ip arp inspection vlan logging command 2-155
IP DHCP snooping
ip dhcp snooping binding command 2-158
ip dhcp snooping command 2-157
ip dhcp snooping database command 2-160
ip dhcp snooping information option allow-untrusted command 2-164
ip dhcp snooping information option command 2-162
ip dhcp snooping information option format remote-id command 2-166
ip dhcp snooping limit rate command 2-167
ip dhcp snooping trust command 2-168
ip dhcp snooping verify command 2-169
ip dhcp snooping vlan command 2-170
ip dhcp snooping vlan information option format-type circuit-id string command 2-171
ip igmp filter command 2-173
ip igmp max-groups command 2-175
ip igmp profile command 2-177
ip igmp snooping command 2-179
ip igmp snooping last-member-query-interval command 2-181
ip igmp snooping querier command 2-183
ip igmp snooping report-suppression command 2-185
ip igmp snooping tcn command 2-187
ip igmp snooping tcn flood command 2-189
ip igmp snooping vlan immediate-leave command 2-190
ip igmp snooping vlan mrouter command 2-191
ip igmp snooping vlan static command 2-193
IP multicast addresses 2-306
IP phones
auto-QoS configuration 2-22
trusting packets sent from 2-299
IP-precedence-to-DSCP map 2-273
ip snap forwarding command 2-195
ip source binding command 2-196
IP source guard
disabling 2-200
displaying
binding entries 2-472
configuration 2-474
dynamic binding entries only 2-455
enabling 2-200
static IP source bindings 2-196
ip ssh command 2-198
IPv6 access list, deny conditions 2-73
ipv6 access-list command 2-201
ipv6 mld snooping command 2-203
ipv6 mld snooping last-listener-query count command 2-205
ipv6 mld snooping last-listener-query-interval command 2-207
ipv6 mld snooping listener-message-suppression command 2-209
ipv6 mld snooping robustness-variable command 2-211
ipv6 mld snooping tcn command 2-213
ipv6 mld snooping vlan command 2-215
IPv6 SDM template 2-358
ipv6 traffic-filter command 2-217
ip verify source command 2-200
J
jumbo frames
L
l2protocol-tunnel command 2-219
l2protocol-tunnel cos command 2-222
LACP
lacp port-priority command 2-223
lacp system-priority command 2-225
Layer 2 mode, enabling 2-673
Layer 2 protocol ports, displaying 2-492
Layer 2 protocol-tunnel
error detection for 2-119
error recovery timer 2-121
Layer 2 protocol tunnel counters 2-54
Layer 2 protocol tunneling error recovery 2-220
Layer 2 traceroute
IP addresses 2-716
MAC addresses 2-713
Layer 3 mode, enabling 2-673
line configuration mode 1-3, 1-6
Link Aggregation Control Protocol
link flap
error detection for 2-119
error recovery timer 2-121
link state group command 2-227
link state track command 2-229
load-distribution methods for EtherChannel 2-335
location (global configuration) command 2-230
location (interface configuration) command 2-232
logging file command 2-234
logical interface 2-130
loopback error
detection for 2-119
recovery timer 2-121
loop guard, for spanning tree 2-620, 2-624
M
mac access-group command 2-236
MAC access-groups, displaying 2-509
MAC access list configuration mode 2-238
mac access-list extended command 2-238
MAC access lists 2-78
MAC addresses
displaying
aging time 2-515
all 2-513
dynamic 2-519
MAC address-table move updates 2-523
notification settings 2-525
number of addresses in a VLAN 2-517
per interface 2-521
per VLAN 2-529
static 2-527
static and dynamic entries 2-511
dynamic
aging time 2-240
deleting 2-57
displaying 2-519
enabling MAC address notification 2-243
enabling MAC address-table move update 2-241
matching 2-258
persistent stack 2-663
static
adding and removing 2-245
displaying 2-527
dropping on an interface 2-246
tables 2-513
MAC address notification, debugging B-17
mac address-table aging-time 2-236, 2-258
mac address-table aging-time command 2-240
mac address-table move update command 2-241
mac address-table notification command 2-243
mac address-table static command 2-245
mac address-table static drop command 2-246
MAC frames
macro apply command 2-248
macro description command 2-251
macro global command 2-252
macro global description command 2-255
macro name command 2-256
macros
adding a description 2-251
adding a global description 2-255
applying 2-252
creating 2-256
displaying 2-556
specifying parameter values 2-252
tracing 2-252
maps
QoS
defining 2-273
displaying 2-539
VLAN
creating 2-737
defining 2-258
displaying 2-589
match (access-map configuration) command 2-258
match (class-map configuration) command 2-260
maximum transmission unit
mdix auto command 2-263
memory (boot loader) command A-13
mkdir (boot loader) command A-15
MLD snooping
configuring queries 2-205, 2-207
configuring topology change notification 2-213
displaying 2-482, 2-484, 2-486, 2-488
enabling 2-203
enabling on a VLAN 2-215
mls qos aggregate-policer command 2-267
mls qos command 2-265
mls qos cos command 2-269
mls qos dscp-mutation command 2-271
mls qos map command 2-273
mls qos queue-set output buffers command 2-277
mls qos queue-set output threshold command 2-279
mls qos rewrite ip dscp command 2-281
mls qos srr-queue input bandwidth command 2-283
mls qos srr-queue input buffers command 2-285
mls qos-srr-queue input cos-map command 2-287
mls qos srr-queue input dscp-map command 2-289
mls qos srr-queue input priority-queue command 2-291
mls qos srr-queue input threshold command 2-293
mls qos-srr-queue output cos-map command 2-295
mls qos srr-queue output dscp-map command 2-297
mls qos trust command 2-299
mls qos vlan-based command 2-301
mode, MVR 2-306
Mode button, and password recovery 2-361
modes, commands 1-2
monitor session command 2-302
more (boot loader) command A-16
MSTP
displaying 2-569
interoperability 2-63
link type 2-622
MST region
aborting changes 2-628
applying changes 2-628
configuration name 2-628
configuration revision number 2-628
current or pending display 2-628
displaying 2-569
MST configuration mode 2-628
VLANs-to-instance mapping 2-628
path cost 2-630
protocol mode 2-626
restart protocol migration process 2-63
root port
loop guard 2-620
preventing from becoming designated 2-620
restricting which can be root 2-620
root guard 2-620
root switch
affects of extended system ID 2-618
interval between BDPU messages 2-634
interval between hello BPDU messages 2-633, 2-640
max-age 2-634
maximum hop count before discarding BPDU 2-635
port priority for selection of 2-636
primary or secondary 2-640
switch priority 2-639
state changes
blocking to forwarding state 2-647
enabling BPDU filtering 2-610, 2-644
enabling BPDU guard 2-612, 2-644
enabling Port Fast 2-644, 2-647
forward-delay time 2-632
length of listening and learning states 2-632
rapid transition to forwarding 2-622
shutting down Port Fast-enabled ports 2-644
state information display 2-568
MTU
configuring size 2-710
displaying global setting 2-579
Multicase Listener Discovery
multicast group address, MVR 2-309
multicast groups, MVR 2-307
Multicast Listener Discovery
multicast router learning method 2-191
multicast router ports, configuring 2-191
multicast router ports, IPv6 2-215
multicast storm control 2-665
multicast VLAN, MVR 2-306
multicast VLAN registration
multiple hosts on authorized port 2-104
Multiple Spanning Tree Protocol
MVR
configuring 2-306
configuring interfaces 2-309
debug messages, display B-21
displaying 2-548
displaying interface information 2-550
members, displaying 2-552
mvr (global configuration) command 2-306
mvr (interface configuration) command 2-309
mvr vlan group command 2-310
N
native VLANs 2-702
native VLAN tagging 2-742
nonegotiate
DTP messaging 2-687
non-IP protocols
denying 2-78
forwarding 2-324
non-IP traffic access lists 2-238
non-IP traffic forwarding
denying 2-78
permitting 2-324
non-stop forwarding 2-311
normal-range VLANs 2-725, 2-731
nsf command 2-311
O
online diagnostics
configuring health monitoring diagnostic tests 2-81
displaying
configured boot-up coverage level 2-405
current scheduled tasks 2-405
event logs 2-405
supported test suites 2-405
test ID 2-405
test results 2-405
test statistics 2-405
enabling
scheduling 2-83
syslog messages 2-81
global configuration mode
clearing health monitoring diagnostic test schedule 2-81
clearing test-based testing schedule 2-83
setting health monitoring diagnostic testing 2-81
setting test-based testing 2-83
setting up health monitoring diagnostic test schedule 2-81
setting up test-based testing 2-83
removing scheduling 2-83
scheduled switchover
disabling 2-83
enabling 2-83
setting test interval 2-83
specifying health monitoring diagnostic tests 2-81
starting testing 2-85
P
PAgP
pagp learn-method command 2-313
pagp port-priority command 2-315
password-recovery mechanism, enabling and disabling 2-361
permit (ARP access-list configuration) command 2-317
permit (IPv6) command 2-319
permit (MAC access-list configuration) command 2-324
per-VLAN spanning-tree plus
physical-port learner 2-313
PID, displaying 2-449
PIM-DVMRP, as multicast router learning method 2-191
platform chassis-management command 2-327
police aggregate command 2-330
police command 2-328
policed-DSCP map 2-273
policy-map command 2-332
policy maps
applying to an interface 2-363, 2-369
creating 2-332
displaying 2-559
hierarchical 2-333
policers
displaying 2-532
for a single class 2-328
for multiple classes 2-267, 2-330
policed-DSCP map 2-273
traffic classification
defining the class 2-42
defining trust states 2-718
setting DSCP or IP precedence values 2-367
Port Aggregation Protocol
port-based authentication
AAA method list 2-3
debug messages, display B-5
enabling guest VLAN supplicant 2-91, 2-101
enabling IEEE 802.1x
globally 2-88
per interface 2-111
guest VLAN 2-102
host modes 2-104
IEEE 802.1x AAA accounting methods 2-1
initialize an interface 2-105
MAC authentication bypass 2-106
manual control of authorization state 2-111
multiple hosts on authorized port 2-104
PAE as authenticator 2-110
periodic re-authentication
enabling 2-114
time between attempts 2-115
quiet period between failed authentication exchanges 2-115
re-authenticating IEEE 802.1x-enabled ports 2-113
resetting configurable IEEE 802.1x parameters 2-100
switch-to-authentication server retransmission time 2-115
switch-to-client frame-retransmission number2-108to 2-109
switch-to-client retransmission time 2-115
port-channel load-balance command 2-335
Port Fast, for spanning tree 2-647
port ranges, defining 2-66, 2-68
ports, debugging B-69
ports, protected 2-700
port security
aging 2-694
debug messages, display B-71
enabling 2-689
violation error recovery 2-121
port trust states for QoS 2-299
port types, MVR 2-309
power information, displaying 2-420
priority-queue command 2-337
priority value, stack member 2-576, 2-668
private-vlan command 2-339
private-vlan mapping command 2-342
private VLANs
association 2-698
configuring 2-339
configuring ports 2-685
displaying 2-585
host ports 2-685
mapping
configuring 2-698
displaying 2-436
promiscuous ports 2-685
product identification information, displaying 2-449
promiscuous ports, private VLANs 2-685
protected ports, displaying 2-442
pruning
VLANs 2-702
VTP
displaying interface information 2-436
pruning-eligible VLAN list 2-704
PVST+
Q
QoS
auto-QoS
configuring 2-22
debug messages, display B-2
displaying 2-379
class maps
creating 2-44
defining the match criteria 2-260
displaying 2-388
defining the CoS value for an incoming packet 2-269
displaying configuration information 2-379, 2-531
DSCP transparency 2-281
DSCP trusted ports
applying DSCP-to-DSCP-mutation map to 2-271
defining DSCP-to-DSCP-mutation map 2-273
egress queues
allocating buffers 2-277
defining the CoS output queue threshold map 2-295
defining the DSCP output queue threshold map 2-297
displaying buffer allocations 2-535
displaying CoS output queue threshold map 2-539
displaying DSCP output queue threshold map 2-539
displaying queueing strategy 2-535
displaying queue-set settings 2-542
enabling bandwidth shaping and scheduling 2-659
enabling bandwidth sharing and scheduling 2-661
limiting the maximum output on a port 2-657
mapping a port to a queue-set 2-344
mapping CoS values to a queue and threshold 2-295
mapping DSCP values to a queue and threshold 2-297
setting maximum and reserved memory allocations 2-279
setting WTD thresholds 2-279
enabling 2-265
ingress queues
allocating buffers 2-285
assigning SRR scheduling weights 2-283
defining the CoS input queue threshold map 2-287
defining the DSCP input queue threshold map 2-289
displaying buffer allocations 2-535
displaying CoS input queue threshold map 2-539
displaying DSCP input queue threshold map 2-539
displaying queueing strategy 2-535
displaying settings for 2-533
enabling the priority queue 2-291
mapping CoS values to a queue and threshold 2-287
mapping DSCP values to a queue and threshold 2-289
setting WTD thresholds 2-293
maps
defining 2-273, 2-287, 2-289, 2-295, 2-297
displaying 2-539
policy maps
applying an aggregate policer 2-330
applying to an interface 2-363, 2-369
creating 2-332
defining policers 2-267, 2-328
displaying policers 2-532
displaying policy maps 2-559
hierarchical 2-333
policed-DSCP map 2-273
setting DSCP or IP precedence values 2-367
traffic classifications 2-42
trust states 2-718
port trust states 2-299
queues, enabling the expedite 2-337
statistics
in-profile and out-of-profile packets 2-535
packets enqueued or dropped 2-535
sent and received CoS values 2-535
sent and received DSCP values 2-535
trusted boundary for IP phones 2-299
VLAN-based 2-301
quality of service
querytime, MVR 2-306
queue-set command 2-344
R
radius-server dead-criteria command 2-345
radius-server host command 2-347
rapid per-VLAN spanning-tree plus
rapid PVST+
re-authenticating IEEE 802.1x-enabled ports 2-113
re-authentication
periodic 2-114
time between attempts 2-115
receiver ports, MVR 2-309
receiving flow-control packets 2-126
recovery mechanism
causes 2-121
display 2-48, 2-386, 2-422, 2-425
timer interval 2-121
reload command 2-349
remote command 2-351
remote-span command 2-353
Remote Switched Port Analyzer
rename (boot loader) command A-17
renew ip dhcp snooping database command 2-355
reset (boot loader) command A-18
reset command 2-740
resource templates, displaying 2-564
restricted VLAN
rmdir (boot loader) command A-19
rmon collection stats command 2-357
root guard, for spanning tree 2-620
routed ports
IP addresses on 2-140
number supported 2-140
routing frames
RSPAN
configuring 2-302
displaying 2-545
filter RSPAN traffic 2-302
remote-span command 2-353
sessions
add interfaces to 2-302
displaying 2-545
start new 2-302
S
scheduled switchover
disabling 2-83
enabling 2-83
SDM mismatch mode 2-359, 2-577
sdm prefer command 2-358
SDM templates
allowed resources 2-359
and stacking 2-359
displaying 2-564
dual IPv4 and IPv6 2-358
secure ports, limitations 2-691
sending flow-control packets 2-126
service password-recovery command 2-361
service-policy command 2-363
session command 2-366
set (boot loader) command A-20
set command 2-367
setup command 2-369
setup express command 2-372
show access-lists command 2-374
show archive status command 2-377
show arp access-list command 2-378
show auto qos command 2-379
show boot command 2-383
show cable-diagnostics tdr command 2-386
show changes command 2-740
show class-map command 2-388
show controllers cpu-interface command 2-389
show controllers ethernet-controller command 2-391
show controllers ethernet-controller fastethernet command 2-398
show controllers tcam command 2-401
show controller utilization command 2-403
show current command 2-740
show dot1q-tunnel command 2-410
show dot1x command 2-411
show dtp 2-415
show eap command 2-417
show env command 2-420
show errdisable detect command 2-422
show errdisable flap-values command 2-424
show errdisable recovery command 2-425
show etherchannel command 2-427
show fallback profile command 2-430
show flowcontrol command 2-432
show idprom command 2-434
show interfaces command 2-436
show interfaces counters command 2-446
show inventory command 2-449
show ip arp inspection command 2-450
show ipc command 2-476
show ip dhcp snooping binding command 2-455
show ip dhcp snooping command 2-454
show ip dhcp snooping database command 2-457, 2-459
show ip igmp profile command 2-462
show ip igmp snooping address command 2-484
show ip igmp snooping command 2-463, 2-482
show ip igmp snooping groups command 2-466
show ip igmp snooping mrouter command 2-468, 2-486
show ip igmp snooping querier command 2-470, 2-488
show ip source binding command 2-472
show ipv6 access-list command 2-480
show ipv6 route updated 2-490
show ip verify source command 2-474
show l2protocol-tunnel command 2-492
show lacp command 2-495
show link state group command 2-499
show location 2-501
show location command 2-501
show logging command 2-504
show mac access-group command 2-509
show mac address-table address command 2-513
show mac address-table aging time command 2-515
show mac address-table command 2-511
show mac address-table count command 2-517
show mac address-table dynamic command 2-519
show mac address-table interface command 2-521
show mac address-table move update command 2-523
show mac address-table notification command 2-58, 2-525, B-19
show mac address-table static command 2-527
show mac address-table vlan command 2-529
show mls qos aggregate-policer command 2-532
show mls qos command 2-531
show mls qos input-queue command 2-533
show mls qos interface command 2-535
show mls qos maps command 2-539
show mls qos queue-set command 2-542
show mls qos vlan command 2-544
show monitor command 2-545
show mvr command 2-548
show mvr interface command 2-550
show mvr members command 2-552
show pagp command 2-554
show parser macro command 2-556
show platform acl command C-2
show platform backup interface command C-3
show platform chassis command C-4
show platform configuration command C-6
show platform dl command C-7
show platform etherchannel command C-8
show platform forward command C-9
show platform frontend-controller command C-11
show platform igmp snooping command C-12
show platform ipc trace command C-20
show platform ip multicast command C-14
show platform ip unicast command C-15
show platform ipv6 unicast command C-21
show platform ip wccp command C-19
show platform layer4op command C-23
show platform mac-address-table command C-24
show platform messaging command C-25
show platform monitor command C-26
show platform mvr table command C-27
show platform pm command C-28
show platform port-asic command C-30
show platform port-security command C-35
show platform qos command C-36
show platform resource-manager command C-37
show platform snmp counters command C-39
show platform spanning-tree command C-40
show platform stack-manager command C-42
show platform stp-instance command C-41
show platform summary command C-44
show platform tb command C-45
show platform tcam command C-47
show platform vlan command C-50
show policy-map command 2-559
show port security command 2-561
show proposed command 2-740
show sdm prefer command 2-564
show setup express command 2-567
show spanning-tree command 2-568
show storm-control command 2-574
show switch command 2-576
show system mtu command 2-579
show trust command 2-718
show udld command 2-580
show version command 2-583
show vlan access-map command 2-589
show vlan command 2-585
show vlan command, fields 2-587
show vlan filter command 2-590
show vmps command 2-591
show vtp command 2-593
shutdown command 2-597
shutdown threshold, Layer 2 protocol tunneling 2-219
shutdown vlan command 2-598
Smartports macros
SNMP host, specifying 2-603
SNMP informs, enabling the sending of 2-599
snmp-server enable traps command 2-599
snmp-server host command 2-603
snmp trap mac-notification command 2-607
SNMP traps
enabling MAC address notification trap 2-607
enabling the MAC address notification feature 2-243
enabling the sending of 2-599
SoftPhone
software images
copying 2-8
deleting 2-70
downloading 2-11
uploading 2-18
software version, displaying 2-583
source ports, MVR 2-309
SPAN
configuring 2-302
debug messages, display B-20
displaying 2-545
filter SPAN traffic 2-302
sessions
add interfaces to 2-302
displaying 2-545
start new 2-302
spanning-tree backbonefast command 2-609
spanning-tree bpdufilter command 2-610
spanning-tree bpduguard command 2-612
spanning-tree cost command 2-614
spanning-tree etherchannel command 2-616
spanning-tree extend system-id command 2-618
spanning-tree guard command 2-620
spanning-tree link-type command 2-622
spanning-tree loopguard default command 2-624
spanning-tree mode command 2-626
spanning-tree mst configuration command 2-628
spanning-tree mst cost command 2-630
spanning-tree mst forward-time command 2-632
spanning-tree mst hello-time command 2-633
spanning-tree mst max-age command 2-634
spanning-tree mst max-hops command 2-635
spanning-tree mst port-priority command 2-636
spanning-tree mst pre-standard command 2-638
spanning-tree mst priority command 2-639
spanning-tree mst root command 2-640
spanning-tree portfast (global configuration) command 2-644
spanning-tree portfast (interface configuration) command 2-647
spanning-tree port-priority command 2-642
Spanning Tree Protocol
spanning-tree transmit hold-count command 2-649
spanning-tree uplinkfast command 2-650
spanning-tree vlan command 2-652
speed command 2-655
srr-queue bandwidth limit command 2-657
srr-queue bandwidth shape command 2-659
srr-queue bandwidth share command 2-661
SSH, configuring version 2-198
stack-mac persistent timer command 2-663
stack member
access 2-366
priority value 2-668
provisioning 2-669
reloading 2-349
stacks, switch
MAC address 2-663
provisioning a new member 2-669
reloading 2-349
stack member access 2-366
stack member number 2-576, 2-671
stack member priority value 2-576, 2-668
static-access ports, configuring 2-675
statistics, Ethernet group 2-357
sticky learning, enabling 2-689
storm-control command 2-665
STP
BackboneFast 2-609
counters, clearing 2-62
debug messages, display
BackboneFast events B-75
MSTP B-78
optimized BPDUs handling B-77
spanning-tree activity B-73
switch shim B-80
transmitted and received BPDUs B-76
UplinkFast B-82
detection of indirect link failures 2-609
enabling protocol tunneling for 2-219
EtherChannel misconfiguration 2-616
extended system ID 2-618
path cost 2-614
protocol modes 2-626
root port
accelerating choice of new 2-650
loop guard 2-620
preventing from becoming designated 2-620
restricting which can be root 2-620
root guard 2-620
UplinkFast 2-650
root switch
affects of extended system ID 2-618, 2-653
hello-time 2-652
interval between BDPU messages 2-652
interval between hello BPDU messages 2-652
max-age 2-652
port priority for selection of 2-642
primary or secondary 2-652
switch priority 2-652
state changes
blocking to forwarding state 2-647
enabling BPDU filtering 2-610, 2-644
enabling BPDU guard 2-612, 2-644
enabling Port Fast 2-644, 2-647
enabling timer to recover from error state 2-121
forward-delay time 2-652
length of listening and learning states 2-652
shutting down Port Fast-enabled ports 2-644
state information display 2-568
SVIs, creating 2-134
Switched Port Analyzer
switching characteristics
modifying 2-673
returning to interfaces 2-673
switchport access command 2-675
switchport backup interface command 2-677
switchport block command 2-680
switchport command 2-673
switchport host command 2-681
switchport mode command 2-682
switchport mode private-vlan command 2-685
switchport nonegotiate command 2-687
switchport port-security aging command 2-694
switchport port-security command 2-689
switchport priority extend command 2-696
switchport private-vlan command 2-698
switchport protected command 2-700
switchports, displaying 2-436
switchport trunk command 2-702
switchport voice detect 2-705
switchport voice vlan command 2-706
switch priority command 2-668
switch provision command 2-669
switch renumber command 2-671
system env temperature threshold yellow command 2-708
system message logging, save message to flash 2-234
system mtu command 2-710
system resource templates 2-358
T
tar files, creating, listing, and extracting 2-15
TDR, running 2-712
temperature information, displaying 2-420
templates, system resources 2-358
test cable-diagnostics tdr command 2-712
traceroute mac command 2-713
traceroute mac ip command 2-716
trunking, VLAN mode 2-682
trunk mode 2-682
trunk ports 2-682
trunks, to non-DTP device 2-683
trusted boundary for QoS 2-299
trusted port states for QoS 2-299
tunnel ports, Layer 2 protocol, displaying 2-492
type (boot loader) command A-23
U
UDLD
debug messages, display B-90
enable globally 2-720
enable per interface 2-722
error recovery timer 2-121
message timer 2-720
reset a shutdown interface 2-724
status 2-580
udld command 2-720
udld port command 2-722
udld reset command 2-724
unicast storm control 2-665
UniDirectional Link Detection
unknown multicast traffic, preventing 2-680
unknown unicast traffic, preventing 2-680
unset (boot loader) command A-24
upgrading
copying software images 2-8
downloading software images 2-11
software images, monitoring status of 2-377
UplinkFast, for STP 2-650
V
version (boot loader) command A-26
version mismatch mode 2-577
vlan (global configuration) command 2-725
vlan (VLAN configuration) command 2-731
vlan access-map command 2-737
VLAN access map configuration mode 2-737
VLAN access maps
actions 2-6
displaying 2-589
VLAN-based QoS 2-301
VLAN configuration
VLAN configuration mode
commands
VLAN 2-731
VTP 2-755
description 1-5
entering 2-739
summary 1-3
vlan database command 2-739
vlan dot1q tag native command 2-742
vlan filter command 2-744
VLAN filters, displaying 2-590
VLAN maps
applying 2-744
creating 2-737
defining 2-258
displaying 2-589
VLAN Query Protocol
VLANs
adding 2-725
debug messages, display
ISL B-86
VLAN IOS file system error tests B-85
VLAN manager activity B-83
VTP B-88
displaying configurations 2-585
extended-range 2-725
MAC addresses
displaying 2-529
number of 2-517
private 2-685
configuring 2-339
displaying 2-585
restarting 2-598
saving the configuration 2-725
shutting down 2-598
SNMP traps for VTP 2-601, 2-604
suspending 2-598
variables 2-731
VLAN Trunking Protocol
VM mode 2-577
VMPS
configuring servers 2-749
displaying 2-591
error recovery timer 2-121
reconfirming dynamic VLAN assignments 2-746
vmps reconfirm (global configuration) command 2-747
vmps reconfirm (privileged EXEC) command 2-746
vmps retry command 2-748
vmps server command 2-749
voice VLAN
setting port priority 2-696
VQP
and dynamic-access ports 2-676
clearing client statistics 2-64
displaying information 2-591
per-server retry count 2-748
reconfirmation interval 2-747
reconfirming dynamic VLAN assignments 2-746
VTP
changing characteristics 2-751
clearing pruning counters 2-65
configuring
file name 2-751
counters display fields 2-594
displaying information 2-593
enabling
tunneling for 2-219
saving the configuration 2-725, 2-735
statistics 2-593
status 2-593
status display fields 2-595
vtp (global configuration) command 2-751
vtp (VLAN configuration) command 2-755
Feedback