Configuring Integration Modules
Cisco SecureX offers integration modules for Cisco security products and third-party solutions. You must configure the module for your product integrations, so the data (and response actions if applicable) are available in SecureX. This section describes the overall process for how to configure a new integration module for your product.
![]() Note |
Only Admin users can add integration modules. The Add button is not visible if you are logged in as a non-admin user. |
Use the Integration Modules tab on SecureX menu bar to configure and view your integration modules, and to view all integration modules that are available for configuration.

You can view the integration modules you have configured on the My Integration Modules page and view all integration modules that are availabe for configuration on the Available Integration Modules page.
In SecureX Demo, you can view all the integration modules that are available for configuration to activate SecureX on the Integration Modules page.

![]() Note |
If your product is an on-premises device, it must be registered in Security Services Exchange before configuring the integration module. See your specific product documentation for configuring devices prior to adding the integration module in SecureX. |
Add Integration Module
Perform the following steps to add an integration module:
Procedure
Step 1 |
Log in to Cisco SecureX. |
||
Step 2 |
Click the Integration Modules tab on the SecureX menu bar. ![]() You can filter the modules that are displayed on the page based on capability. You can also search for modules that are displayed on the page based on integration module name and description.
|
||
Step 3 |
On the Available Integration Modules page, navigate to the integration module you want to configure and click Add or Enable in the module panel. If you are on the My Integration Modules page, click Add New Integration Module to open the Available Integration Modules page. ![]()
In SecureX Demo, navigate to the integration module you want to configure and click Enable in the module panel. |
||
Step 4 |
Complete the Add New Module or Enable Module form, following the instructions in Quick Start panel. ![]() |
||
Step 5 |
Click Save to add the integration module. A health check is performed to determine if the module was properly configured. A message is displayed in the upper portion of the form (the form changes to Edit Module since it's been saved) indicating that the health check is running. Once it completes, a messsage displays indicating that either there were no issues with the configuration or that errors were found. ![]() If errors occur, correct the configuration and click Save. |
||
Step 6 |
Click Cancel to exit the form. The module is displayed on the My Integration Modules page and shows whether it is Integrated or if there are Errors with the configuration. |
Filter Integration Modules
On the Available Integration Modules page, click the Filter drop-down and check the check boxes next to the capability to filter the modules that are displayed on the page.

The modules that match your selections are displayed on the page.
Search Integration Modules
Enter the search criteria in the Search Integrations text box on the Available Integration Modules or My Integration Modules page to search for integration modules by integration module name and description. The integration modules that match your search criteria are displayed on the Available Integration Modules or My Integration Modules page.
Updating Integration Modules
All integration modules configured for your environment are shown on the My Integration Modules page. The module panel indicates whether the module is Integrated (successfully configured) or if it has an Error with the configuration. If it has errors, you can edit the module.
Perform the following steps to edit an integration module:
Procedure
Step 1 |
Log in to Cisco SecureX. |
Step 2 |
Click the Integration Modules tab on the SecureX menu bar. |
Step 3 |
Navigate to the module on the My Integration Modules page and click Edit in the module pane. The Edit Integration Module form opens with the current integration module settings. |
Step 4 |
Edit the settings as needed and click Save. A health check is performed to determine if the module was properly configured. A message is displayed in the upper portion of the Edit Module form indicating that the health check is running. Once it completes, a messsage displays indicating that either there were no issues with the configuration or that errors were found. |
Step 5 |
Click Cancel to exit the form. |
Deleting Integration Module
All modules associated with your account shown on the My Integration Modules page. You can delete an integration module, and all data from that integration will no longer be available.
Perform the following steps to delete an integration module:
Procedure
Step 1 |
Log in to Cisco SecureX. |
||
Step 2 |
Navigate to the module on the My Integration Modules page and click Edit in the module panel. The Edit Module form opens with the current integration module settings. |
||
Step 3 |
Click Delete. |
||
Step 4 |
On the confirmation dialog, click Delete. The integration module is removed and its data is no longer available.
|