Cisco FXOS Faults and Error Messages, 1.1(2)

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents
Find Matches in This Book
Available Languages
Download Options

Book Title

Cisco FXOS Faults and Error Messages, 1.1(2)

Chapter Title

Troubleshooting Transient Faults

Results

Updated:
July 16, 2015

Chapter: Troubleshooting Transient Faults

Troubleshooting Transient Faults

Transient faults can occur during initial set up and discovery or when a server or virtual machine starts up. You can typically ignore these transient faults, as FXOS clears them automatically.

This chapter includes the following sections:

Initial Setup and Discovery Faults

Table 4-1 describes the transient faults that you may see during the initial setup and discovery process. The FXOS clears these faults. If you see them during the initial setup or discovery process, you can safely ignore these faults.

Table 4-1 Transient Faults that Occur during Initial Setup and Discovery Process
Fault Code
Fault Text
Description

F16581
[FSM:STAGE:RETRY:]: user configuration to secondary(FSM-STAGE:sam:dme:
AaaUserEpUpdateUserEp:SetUserPeer)

The FSM could not send the user configuration to the subordinate fabric interconnect during the initial cluster configuration or the setup.

F16745
[FSM:STAGE:RETRY:]: QoS Classification Definition classification configuration on secondary(FSM-STAGE:sam:dme:QosclassDefinitionConfigGlobalQoS:SetPeer)

The FSM could not send the quality of the service configuration to the subordinate fabric interconnect during the initial cluster configuration or the setup.

F16725
[FSM:STAGE:RETRY:]: VM profile configuration on external VM manager(FSM-STAGE:sam:dme:VnicProfileSetConfigVmm:SetLocal)

The FSM could not send the VM profile configuration to the subordinate fabric interconnect during the initial cluster configuration or the setup.

F16580
[FSM:STAGE:RETRY:]: realm configuration to secondary(FSM-STAGE:sam:dme:
AaaRealmUpdateRealm:SetRealmPeer)

The FSM could not send the security configuration to the subordinate fabric interconnect during the initial cluster configuration or the setup.

F16724
[FSM:STAGE:RETRY:]: external VM manager configuration on local fabric(FSM-STAGE:sam:dme:ExtvmmEpConfig:SetLocal)

The FSM could not send the VM manager configuration to the primary fabric interconnect during the initial cluster configuration or the setup.

F16579
[FSM:STAGE:RETRY:]: external aaa server configuration to secondary(FSM-STAGE:
sam:dme:AaaEpUpdateEp:SetEpPeer)

The FSM could not send the security configuration to the subordinate fabric interconnect during the initial cluster configuration or the setup.

F16749
[FSM:STAGE:RETRY:]: Uplink eth port configuration on B(FSM-STAGE:
sam:dme:SwEthLanBorderDeploy:
UpdateConnectivity)

The FSM could not send the eth-uplink configuration to the fabric interconnects during the initial cluster configuration or the setup.

F16749
[FSM:STAGE:RETRY:]: internal network configuration on B(FSM-STAGE:
sam:dme:SwAccessDomainDeploy:
UpdateConnectivity)

The FSM could not send the internal network configuration to the fabric interconnects during the initial cluster configuration or the setup.

F16749
[FSM:STAGE:RETRY:]: Uplink fc port configuration on B(FSM-STAGE:sam:
dme:SwFcSanBorderDeploy:
UpdateConnectivity)

The FSM could not send the fibre channel uplink configuration to the fabric interconnects during the initial cluster configuration or the setup.

F16680
[FSM:STAGE:RETRY:]: Enable virtual interface on local fabric interconnect
(FSM-STAGE:sam:dme:MgmtIfEnableVip:
Local)

The FSM could not send the virtual interface configuration to the fabric interconnects during the initial cluster configuration or the setup.

F16579
[FSM:STAGE:RETRY:]: keyring configuration on secondary(FSM-STAGE:
sam:dme:PkiEpUpdateEp:SetKeyRingPeer)

The FSM could not send the security configuration to the subordinate fabric interconnect during the initial cluster configuration or the setup.

F16539
[FSM:STAGE:RETRY:]: Fabric interconnect mode configuration to primary(FSM-STAGE:
sam:dme:FabricLanCloudSwitchMode:
SwConfigPeer)

The FSM could not send the end-host mode configuration on to the primary fabric interconnect during the initial cluster configuration or the setup.

F0429
Fabric Interconnect A, HA functionality not ready

The cluster configuration cannot be completed until the chassis discovery is completed.

F0400
Chassis 1 connectivity configuration: un-acknowledged

FXOS discovered the chassis with only one link in the first attempt although the chassis discovery policy is configured for four links. FXOS reacknowledges the chassis to activate the other links.

F0401
IOM 1/2 (B) current connectivity does not match discovery policy: unsupported-connectivity

FXOS discovered the chassis with only one link in the first attempt although the chassis discovery policy is configured for four links.

FXOS can clear this fault when the communication is established between the chassis and the fabric interconnect with that link.

F0440
Chassis discovery policy conflict: Link IOM 1/2/2 to fabric interconnect B:1/1 not configured

FXOS discovered the chassis with only one link in the first attempt although the chassis discovery policy is configured for four links. Until the discovery is successful with that link, the remaining links cannot be marked as active.

FXOS can clear this fault when the communication is established between the chassis and the fabric interconnect with that link.

F0332
AssociatePnuOSLocalDiskConfig fails with Service-Unavailable

During discovery, the server association failed due to an error when configuring the local disk controller.

The associated remote invocation error code is 4106.

F0277
ether port 1 on fabric interconnect B oper state: link-up, reason: FEX not configured

FXOS discovered the chassis with only one link in the first attempt although the chassis discovery policy is configured for four links. Until the discovery is successful with that link, the remaining links cannot be marked as active.

F0276
ether port 4 on fabric interconnect B oper state: link-down, reason: Link failure or not-connected

One or more of the links on the chassis flapped during the initial discovery. This fault is generated when the link is down during the flapping.

F0206
Adapter 1/2/1 is unreachable

During discovery, the adapter information cannot be accessed from the server. This fault clears as soon as the information is available.

F0283
VIF 1 / 2 B-42/44 down, reason: Bound Physical Interface Down

The internal VIF that the FXOS uses during discovery failed.

F0367
No link between IOM port 1/1/2 and fabric interconnect A:1/2

The ethernet server ports flapped on the fabric interconnect during the initial discovery, because the discovery policy was configured for more than one link.

FXOS clears this fault when the initial discovery succeeds with one link and the other links can be marked as active.

F0399
Current connectivity for chassis 1 does not match discovery policy: unsupported-connectivity

FXOS discovered the chassis with only one link in the first attempt although the chassis discovery policy is configured for four links. Until the discovery is successful with that link, the remaining links cannot be marked as active.

F16520
[FSM:STAGE:RETRY:]: Identify pre-boot environment agent on server 1/2
(FSM-STAGE:sam:dme:ComputeBlade
Discover:PnuOSIdent)

The FSM failed to identify the pre-boot environment on the server during discovery.

F77960
[FSM:STAGE:REMOTE-ERROR]: Result: end-point-unavailable Code: unspecified Message: Waiting for BIOS POST Completion information from IBMC(sam:dme:ComputeBladeDiscover:
BiosPostCompletion)

The FSM did not receive a response from the server during discovery and is waiting for the BIOS POST completion information.

F0320
Server 1/1 (service profile:) has an invalid FRU: mismatch-identity-unestablishable

FXOS could not identify the FRUs from the servers during initial discovery.

F77959
[FSM:STAGE:REMOTE-ERROR]: Result: unidentified-fail Code: ERR-0505-IBMC-fru-retrieval-error Message: Could not get Fru from 7f060101,
dn=fabric/server/chassis-1/slot-1 (sam:dme:FabricComputeSlotEpIdentify:ExecuteLocal)

FXOS could not identify the FRUs from the servers during initial discovery.

F16406
[FSM:STAGE:RETRY:]: triggering chassis discovery via IOM 1/2(right)(FSM-STAGE:sam:dme:EquipmentIOCardFeConn:DiscoverChassis)

In a cluster configuration, after the FXOS discovers the chassis through the I/O module connected to the primary fabric interconnect, it raises discovery through the I/O module connected to the secondary fabric interconnect.

Virtual Machine Startup Faults

When you power on a virtual machine on a server that has network adaptors connected to a distributed virtual wwitch through a port profile, the Events tab of the VMware vCenter may display the following event:

Virtual machine powered On with vNICs connected to dvPorts that have a port level configuration, which might be different from the dvPort group configuration.

If you see this event, you can safely ignore it.

Was this Document Helpful?

FeedbackFeedback

Contact Cisco