Step 1 |
enable
|
Enables privileged EXEC mode.
|
Step 2 |
configure
terminal
Router# configure terminal
|
Enters global configuration mode.
|
Step 3 |
l2
vfi
name
manual
Router(config)# l2 vfi vfi1 manual
|
Establishes a Layer 2 VFI between two separate networks and enters VFI configuration mode.
|
Step 4 |
vpn
id
vpn-id
Router(config-vfi)# vpn id 100
|
Sets or updates a Virtual Private Network (VPN) ID on a VPN routing and forwarding (VRF) instance.
|
Step 5 |
status
decoupled
Router(config-vfi)# status decoupled
|
(Optional) Enables decoupled mode. The state of the attachment circuits on the user-facing Provider Edge (uPE) is decoupled
from the state of the pseudowires. The mLACP controls the state of the attachment circuits.
|
Step 6 |
neighbor
neighbor
ip-address
vc-id
{encapsulation mpls | pw-class pw-class-name }
Router(config-vfi)# neighbor 10.1.1.1 50 encapsulation mpls
|
Specifies the routers that should form a VFI connection.
|
Step 7 |
exit
|
Exits VFI configuration mode and returns to global configuration mode.
|
Step 8 |
interface
port-channel
port-channel-
number
Router(config)# interface port-channel1
|
Configures the port channel and enters interface configuration mode.
|
Step 9 |
no
ip
address
Router(config-if)# no ip address
|
Specifies that the VLAN interface does not have an IP address assigned to it.
|
Step 10 |
lacp
fast-switchover
Router(config-if)# lacp fast-switchover
|
Enables LACP 1-to-1 link redundancy.
|
Step 11 |
lacp
max-bundle
max-bundles
Router(config-if)# lacp max-bundle 2
|
Configures the max-bundle links that are connected to the PoA. The value of the max-bundles argument should not be less than the total number of links in the LAG that are connected to the PoA.
-
Determines whether the redundancy group is under DHD control, PoA control, or both.
-
Range is 1 to 8. Default value is 8.
|
Step 12 |
exit
|
Exits interface configuration mode.
|
Step 13 |
redundancy
Router(config)# redundancy
|
|
Step 14 |
interchassis
group
group-id
Router(config-red)# interchassis group 230
|
Specifies that the port channel is an mLACP port-channel.
|
Step 15 |
exit
Router(config-r-ic)# exit
|
Exits interchassis redundancy mode.
|
Step 16 |
exit
|
Exits redundancy configuration mode.
|
Step 17 |
interface
port-channel
port-channel-
number
Router(config)# interface port-channel1
|
Configures the port channel and enters interface configuration mode.
|
Step 18 |
service
instance
id
ethernet
[evc-name ]
Router(config-if)# service instance 1 ethernet
|
Configures an Ethernet service instance and enters Ethernet service configuration mode.
|
Step 19 |
encapsulation
dot1q
vlan-id
[, vlan-id [- vlan-id ]] [native ]
Router(config-if-srv)# encapsulation dot1q 100
|
Enables IEEE 802.1Q encapsulation of traffic on a specified subinterface in a VLAN.
|
Step 20 |
bridge-domain
bridge-id
[split-horizon [group group-id ]]
Router(config-if-srv)# bridge-domain 200
|
Configures the bridge domain. Binds the service instance to a bridge domain instance where domain-number is the identifier for the bridge domain instance.
|
Step 21 |
exit
Router(config-if-srv)# exit
|
Exits service instance configuration mode.
|
Step 22 |
interface
vlan
vlanid
Router(config-if)# interface vlan 200
|
Creates a dynamic switch virtual interface (SVI).
|
Step 23 |
no
ip
address
Router(config-if)# no ip address
|
Specifies that the VLAN interface does not have an IP address assigned to it.
|
Step 24 |
xconnect
vfi
vfi-name
Router(config-if)# xconnect vfi vfi-16
|
Specifies the Layer 2 VFI that you are binding to the VLAN port.
|
Step 25 |
end
|
Returns the CLI to privileged EXEC mode.
|