Cisco IOS XR Virtual Private Network Command Reference for the Cisco CRS Router, Release 6.1.x

action (VPLS)

To configure the bridge behavior when the number of learned MAC addresses reaches the MAC limit configured, use the action command in L2VPN bridge group bridge domain MAC limit configuration mode. To disable this feature, use the no form of this command.

action {flood | no-flood | shutdown}

no action {flood | no-flood | shutdown}

Syntax Description


flood	Configures the action to flood all unknown unicast packets when the MAC limit is reached. If the action is set to flood, all unknown unicast packets, with unknown destinations addresses, are flooded over the bridge.
no-flood	Configures the action to no-flood so all unknown unicast packets are dropped when the MAC limit is reached. If the action is set to no-flood, all unknown unicast packets, with unknown destination addresses, are dropped.
shutdown	Stops forwarding when the MAC limit is reached. If the action is set to shutdown, all packets are dropped.

Command Default

No action is taken when the MAC address limit is reached.

Command Modes

L2VPN bridge group bridge domain MAC limit configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the action command to specify the type of action to be taken when the action is violated.

The configured action has no impact if the MAC limit has not been reached.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure the bridge bar to flood all unknown unicast packets when the number of MAC addresses learned by the bridge reaches 10:


RP/0/RP0/CPU0:router#configure
RP/0/RP0/CPU0:router(config)#l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)#bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)#bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)#mac
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac)#limit
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac-limit)#action flood
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac-limit)#maximum 10

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
limit (VPLS)	Sets the MAC address limit for action, maximum, and notification and enters L2VPN bridge group bridge domain MAC limit configuration mode.
l2vpn	Enters L2VPN configuration mode.
mac (VPLS)	Enters L2VPN bridge group bridge domain MAC configuration mode.
maximum (VPLS)	Configures the specified action when the number of MAC addresses learned on a bridge is reached.
notification (VPLS)	Specifies the type of notification that is sent when the number of learned MAC addresses exceeds the configured limit.

aging (VPLS)

To enter the MAC aging configuration submode to set the aging parameters such as time and type, use the aging command in L2VPN bridge group bridge domain configuration mode. To return to the default value for all parameters that are attached to this configuration submode, use the no form of this command.

aging

no aging

Syntax Description

This command has no keywords or arguments.

Command Default

No defaults are attached to this parameter since it is used as a configuration submode. See defaults that are assigned to the time (VPLS) and the type (VPLS) parameters.

Command Modes

L2VPN bridge group bridge domain MAC configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the aging command to enter L2VPN bridge group bridge domain MAC aging configuration mode.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to enter MAC aging configuration submode and to set the MAC aging time to 120 seconds:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# mac
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac)# aging
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac-aging)# time 120

Related Commands


Commands	Description
bridge-domain (VPLS)	Establishes a bridge domain and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then assigns network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
mac (VPLS)	Enters L2VPN bridge group bridge domain MAC configuration mode.
time (VPLS)	Configures the maximum aging time.
type (VPLS)	Configures the type for MAC address aging.

bridge-domain (VPLS)

To establish a bridge domain and to enter L2VPN bridge group bridge domain configuration mode, use the bridge-domain command in L2VPN bridge group configuration mode. To return to a single bridge domain, use the no form of this command.

bridge-domain bridge-domain-name

no bridge-domain bridge-domain-name

Syntax Description

bridge-domain-name

Name of the bridge domain.

Note

The maximum number of characters that can be specified in the bridge domain name is 27.

Command Default

The default value is a single bridge domain.

Command Modes

L2VPN bridge group configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

Use the bridge-domain command to enter L2VPN bridge group bridge domain configuration mode.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure a bridge domain:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)#

Related Commands

Command	Description
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.

bridge group (VPLS)

To create a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain, use the bridge group command in L2VPN configuration mode. To remove all the bridge domains that are created under this bridge group and to remove all network interfaces that are assigned under this bridge group, use the no form of this command.

bridge group bridge-group-name

no bridge-group bridge-group-name

Syntax Description


`bridge-group-name`	Number of the bridge group to which the interface belongs.

Command Default

No bridge group is created.

Command Modes

L2VPN configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the bridge group command to enter L2VPN bridge group configuration mode.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows that bridge group 1 is assigned:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)#

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
l2vpn	Enters L2VPN configuration mode.

clear l2vpn bridge-domain (VPLS)

To clear the MAC addresses and to restart the bridge domains on the router, use the clear l2vpn bridge-domain command in EXEC mode.

clear l2vpn bridge-domain {all | bd-name name | group group}

Syntax Description


all	Clears and restarts all the bridge domains on the router.
bd-name `name`	Clears and restarts the specified bridge domain. The `name` argument specifies the name of the bridge-domain.
group `group`	Clears and restarts all the bridge domains that are part of the bridge group.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

This is the method that allows a bridge to forward again after it was put in Shutdown state as a result of exceeding the configured MAC limit.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to clear all the MAC addresses and to restart all the bridge domains on the router:


RP/0/RP0/CPU0:router# clear l2vpn bridge-domain all

Related Commands

Command	Description
show l2vpn bridge-domain (VPLS)	Display information for the bridge ports such as attachment circuits and pseudowires for the specific bridge domains.

flooding disable

To configure flooding for traffic at the bridge domain level or at the bridge port level, use the flooding disable command in L2VPN bridge group bridge domain configuration mode. To return the bridge to normal flooding behavior when all unknown unicast packets, all broadcast packets, and all multicast packets are flooded over all other bridge domain network interfaces, use the no form of this command.

flooding disable

no flooding disable

This command has no keywords or arguments.

Command Default

The default behavior is that packets are flooded when their destination MAC address is not found.

Command Modes

L2VPN bridge group bridge domain configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the flooding disable command to override the parent bridge configuration.

By default, bridge ports inherit the flooding behavior of the bridge domain.

When flooding is disabled, all unknown unicast packets, all broadcast packets, and all multicast packets are discarded.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to disable flooding on the bridge domain called bar:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# flooding disable

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
mtu (VPLS)	Adjusts the maximum packet size or maximum transmission unit (MTU) size for the bridge domain.

interface (VPLS)

To add an interface to a bridge domain that allows packets to be forwarded and received from other interfaces that are part of the same bridge domain, use the interface command in L2VPN bridge group bridge domain configuration mode. To remove an interface from a bridge domain, use the no form of this command.

interface type interface-path-id

no interface type interface-path-id

Syntax Description

type

Interface type. For more information, use the question mark (? ) online help function.

interface-path-id

Physical interface or virtual interface.

Note

Use the show interfaces command to see a list of all interfaces currently configured on the router.

For more information about the syntax for the router, use the question mark (? ) online help function.

Command Default

None

Command Modes

L2VPN bridge group bridge domain configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the interface command to enter L2VPN bridge group bridge domain attachment circuit configuration mode. In addition, the interface command enters the interface configuration submode to configure parameters specific to the interface.

By default, an interface is not part of a bridge.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure the bundle Ethernet interface as an attachment circuit:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# interface gigabitethernet 0/1/0/9
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-ac)#

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.

learning disable (VPLS)

To override the MAC learning configuration of a parent bridge or to set the MAC learning configuration of a bridge, use the learning disable command in L2VPN bridge group bridge domain MAC configuration mode. To disable this feature, use the no form of this command.

learning disable

no learning disable

Syntax Description

This command has no keywords or arguments.

Command Default

By default, learning is enabled on all bridge domains and all interfaces on that bridge inherits this behavior.

Command Modes

L2VPN bridge group bridge domain MAC configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

When set, the learning disable command stops all MAC learning either on the specified interface or the bridge domain.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

In the following example, MAC learning is disabled on all ports in the bridge domain called bar, which is applied to all interfaces in the bridge unless the interface has its own MAC learning enable command.


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# mac
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac)# learning disable

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
mac (VPLS)	Enters L2VPN bridge group bridge domain MAC configuration mode.

limit (VPLS)

To set the MAC address limit for action, maximum, and notification and to enter L2VPN bridge group bridge domain MAC limit configuration mode, use the limit command in L2VPN bridge group bridge domain MAC configuration mode. To remove all limits that were previously configured under the MAC configuration submodes, use the no form of this command.

limit

no limit

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

L2VPN bridge group bridge domain MAC configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the limit command to enter L2VPN bridge group bridge domain MAC limit configuration mode. The limit command specifies that one syslog message is sent or a corresponding trap is generated with the MAC limit when the action is violated.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how the MAC limit for the bridge bar is set to 100 with an action of shutdown. After the configuration, the bridge stops all forwarding after 100 MAC addresses are learned. When this happens, a syslog message and an SNMP trap are created.


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# mac
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac)# limit
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac-limit)# maximum 100
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac-limit)# action shutdown
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac-limit)# notification both

Related Commands

Command	Description
action (VPLS)	Configures bridge behavior when the number of learned MAC addresses reaches the MAC limit configured.
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
mac (VPLS)	Enters L2VPN bridge group bridge domain MAC configuration mode.
maximum (VPLS)	Configures the specified action when the number of MAC addresses learned on a bridge is reached.
notification (VPLS)	Specifies the type of notification that is sent when the number of learned MAC addresses exceeds the configured limit.

mac (VPLS)

To enter L2VPN bridge group bridge domain MAC configuration mode, use the mac command in L2VPN bridge group bridge domain configuration mode. To disable all configurations added under the MAC configuration submodes, use the no form of this command.

mac

no mac

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

L2VPN bridge group bridge domain configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the mac command to enter L2VPN bridge group bridge domain MAC configuration mode.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to enter L2VPN bridge group bridge domain MAC configuration mode:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# mac
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac)#

Related Commands

Command	Description
aging (VPLS)	Enters the MAC aging configuration submode to set the aging parameters such as time and type.
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
learning disable (VPLS)	Overrides the MAC learning configuration of a parent bridge or sets the MAC learning configuration of a bridge.
limit (VPLS)	Sets the MAC address limit for action, maximum, and notification and enters L2VPN bridge group bridge domain MAC limit configuration mode.
static-address (VPLS)	Adds static entries to the MAC address for filtering.
withdraw (VPLS)	Disables MAC address withdrawal for a specified bridge domain

maximum (VPLS)

To configure the specified action when the number of MAC addresses learned on a bridge is reached, use the maximum command in L2VPN bridge group bridge domain MAC limit configuration mode. To disable this feature, use the no form of this command.

maximum value

no maximum value

Syntax Description


`value`	Maximum number of learned MAC addresses. The range is from 5 to 512000.

Command Default

The default maximum value is 4000.

Command Modes

L2VPN bridge group bridge domain MAC limit configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The action can either be flood, no flood, or shutdown. Depending on the configuration, a syslog, an SNMP trap notification, or both are issued.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows when the number of MAC address learned on the bridge reaches 5000 and the bridge stops learning but continues flooding:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# mac
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac)# limit
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac-limit)# maximum 5000
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac-limit)# action no-flood

Related Commands

Command	Description
action (VPLS)	Configures bridge behavior when the number of learned MAC addresses reaches the MAC limit configured.
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
limit (VPLS)	Sets the MAC address limit for action, maximum, and notification and enters L2VPN bridge group bridge domain MAC limit configuration mode.
mac (VPLS)	Enters L2VPN bridge group bridge domain MAC configuration mode.
notification (VPLS)	Specifies the type of notification that is sent when the number of learned MAC addresses exceeds the configured limit.

mpls static label (VPLS)

To configure the MPLS static labels and the static labels for the access pseudowire configuration, use the mpls static label command in L2VPN bridge group bridge domain VFI pseudowire configuration mode. To assign the dynamic MPLS labels to either the virtual forwarding interface (VFI) pseudowire or the access pseudowire, use the no form of this command.

mpls static label local value value remote value

no mpls static label local value value remote value

Syntax Description

local value

Configures the local pseudowire label.

Note

Use the show mpls label range command to obtain the range for the local labels.

remote value

Configures the remote pseudowire label.

Note

The range of values for the remote labels depends on the label allocator of the remote router.

Command Default

By default, the router attempts to assign dynamic labels to the pseudowire.

Command Modes

L2VPN bridge group bridge domain Access/VFI pseudowire configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Ensure that both ends of the pseudowire have matching static labels.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure the VFI pseudowire 10.1.1.2 with pseudowire ID of 1000 to use MPLS label 800 and remote MPLS label 500:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# vfi model
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-vfi)# neighbor 10.1.1.2 pw-id 1000
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-vfi-pw)# mpls static label local 800 remote 500

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
neighbor (VPLS)	Adds an access pseudowire port to a bridge domain or a pseudowire to a bridge virtual forwarding interface (VFI).
pw-class (VFI)	Configures the pseudowire class template name to use for the pseudowire.
vfi (VPLS)	Configures virtual forwarding interface (VFI) parameters.

mtu (VPLS)

To adjust the maximum packet size or maximum transmission unit (MTU) size for the bridge domain, use the mtu command in L2VPN bridge group bridge domain configuration mode. To disable this feature, use the no form of this command.

mtu bytes

no mtu

Syntax Description


`bytes`	MTU size, in bytes. The range is from 46 to 65535.

Command Default

The default MTU value is 1500.

Command Modes

L2VPN bridge group bridge domain configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Each interface has a default maximum packet size or MTU size. This number generally defaults to the largest size possible for that interface type. On serial interfaces, the MTU size varies, but cannot be set smaller than 64 bytes.

The MTU for the bridge domain includes only the payload of the packet. For example, a configured bridge MTU of 1500 allows tagged packets of 1518 bytes (6 bytes DA, 6 bytes SA, 2 bytes ethertype, or 4 bytes qtag).

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example specifies an MTU of 1000 bytes:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# mtu 1000

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
flooding disable	Configures flooding for traffic at the bridge domain level or at the bridge port level.
l2vpn	Enters L2VPN configuration mode.

neighbor (VPLS)

To add an access pseudowire port to a bridge domain or a pseudowire to a bridge virtual forwarding interface (VFI), use the neighbor command in the appropriate L2VPN bridge group bridge domain configuration submode. To remove the pseudowire either from the bridge or from the VFI, use the no form of this command.

neighbor A.B.C.D pw-id value

no neighbor A.B.C.D pw-id value

Syntax Description


`A.B.C.D`	IP address of the cross-connect peer.
pw-id `value`	Configures the pseudowire ID and ID value. Range is 1 to 4294967295.

Command Default

None

Command Modes

L2VPN bridge group bridge domain configuration

L2VPN bridge group bridge domain VFI configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the neighbor command to enter L2VPN bridge group bridge domain VFI pseudowire configuration mode. Alternatively, use the neighbor command to enter L2VPN bridge group bridge domain access pseudowire configuration mode.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure an access pseudowire directly under a bridge domain in L2VPN bridge group bridge domain configuration mode:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# neighbor 10.1.1.2 pw-id 1000
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-pw)#

The following example shows how to configure the parameters for any pseudowire in L2VPN bridge group bridge domain VFI configuration mode:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# vfi v1
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-vfi)# neighbor 10.1.1.2 pw-id 1000
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-vfi-pw)#

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
mpls static label (VPLS)	Configures the MPLS static labels and the static labels for the access pseudowire configuration.
pw-class (VFI)	Configures the pseudowire class template name to use for the pseudowire.
static-mac-address (VPLS)	Configures the static MAC address to associate a remote MAC address with a pseudowire or any other bridge interface.
vfi (VPLS)	Configures virtual forwarding interface (VFI) parameters.

notification (VPLS)

To specify the type of notification that is sent when the number of learned MAC addresses exceeds the configured limit, use the notification command in L2VPN bridge group bridge domain MAC limit configuration mode. To use the notification as only a syslog entry, use the no form of this command.

notification {both | none | trap}

no notification {both | none | trap}

Syntax Description


both	Sends syslog and trap notifications when the action is violated.
none	Specifies no notification.
trap	Sends trap notifications when the action is violated.

Command Default

By default, only a syslog message is sent when the number of learned MAC addresses reaches the maximum configured.

Command Modes

L2VPN bridge group bridge domain MAC limit configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

A syslog message and an SNMP trap is generated. Alternatively, an SNMP trap is generated. Finally, no notification is generated.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how both a syslog message and an SNMP trap are generated with the bridge bar and learns more MAC addresses than the configured limit:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# mac
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac)# limit
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac-limit)# notification both

Related Commands

Command	Description
action (VPLS)	Configures bridge behavior when the number of learned MAC addresses reaches the MAC limit configured.
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
mac (VPLS)	Enters L2VPN bridge group bridge domain MAC configuration mode.
maximum (VPLS)	Configures the specified action when the number of MAC addresses learned on a bridge is reached.

port-down flush disable (VPLS)

To disable MAC flush when the bridge port is nonfunctional, use the port-down flush disable command in the L2VPN bridge group bridge domain MAC configuration mode. Use the no form of this command to enable the MAC flush when the bridge port is nonfunctional.

port-down flush disable

no port-down flush disable

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

L2VPN bridge group bridge domain MAC configuration

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The port-down flush disable command disables the MAC flush when the bridge port is nonfunctional.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to disable MAC flush when the bridge port is nonfunctional:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# mac
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac)# port-down flush disable

Related Commands

Command	Description
action (VPLS)	Configures bridge behavior when the number of learned MAC addresses reaches the MAC limit configured.
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
mac (VPLS)	Enters L2VPN bridge group bridge domain MAC configuration mode.
maximum (VPLS)	Configures the specified action when the number of MAC addresses learned on a bridge is reached.
notification (VPLS)	Specifies the type of notification that is sent when the number of learned MAC addresses exceeds the configured limit.

pw-class (VFI)

To configure the pseudowire class template name to use for the pseudowire, use the pw-class command in L2VPN bridge group bridge domain VFI pseudowire configuration mode. To delete the pseudowire class, use the no form of this command.

pw-class class-name

no pw-class class-name

Syntax Description


`class-name`	Pseudowire class name.

Command Default

None

Command Modes

L2VPN bridge group bridge domain VFI pseudowire configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to attach the pseudowire class to the pseudowire:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# vfi v1
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-vfi)# neighbor 10.1.1.2 pw-id 1000
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-vfi-pw)# pw-class canada

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
mpls static label (VPLS)	Configures the MPLS static labels and the static labels for the access pseudowire configuration.
neighbor (VPLS)	Adds an access pseudowire port to a bridge domain or a pseudowire to a bridge virtual forwarding interface (VFI).
vfi (VPLS)	Configures virtual forwarding interface (VFI) parameters.

show l2vpn bridge-domain (VPLS)

To display information for the bridge ports such as attachment circuits and pseudowires for the specific bridge domains, use the show l2vpn bridge-domain command in EXEC mode.

Syntax Description

bd-name bridge-domain-name

(Optional) Displays the bridges by the bridge ID. The bridge-domain-name argument is used to name a bridge domain.

brief

(Optional) Displays brief information about the bridges.

detail

(Optional) Displays the output for the Layer 2 VPN (L2VPN) to indicate whether or not the MAC withdrawal feature is enabled and the number of MAC withdrawal messages that are sent or received from the pseudowire.

group bridge-domain- group-name

(Optional) Displays filter information on the bridge-domain group name. The bridge-domain-group-name argument is used to name the bridge domain group.

interface

(Optional) Displays the filter information for the interface on the bridge domain.

type

Interface type. For more information, use the question mark (?) online help function.

interface-path-id

Physical interface or virtual interface.

Note

Use the show interfaces command to see a list of all interfaces currently configured on the router.

For more information about the syntax for the router, use the question mark (? ) online help function.

neighbor IP-address

(Optional) Displays only the bridge domain that contains the pseudowires to match the filter for the neighbor. The IP-address argument is used to configure IP address of the neighbor.

pw-id value

(Optional) Displays the filter for the pseudowire ID. The range is from 1 to 4294967295.

summary

(Optional) Displays the summary information for the bridge domain.

Command Default

None

Command Modes

EXEC mode

Command History


Release	Modification
Release 3.8.0	This command was introduced.
Release 5.1.2	This command was modified to enable filtering the command output for specific pseudowire with just the pseudowire ID.

Usage Guidelines

To use commands of this module, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using any command, contact your AAA administrator for assistance.

Use the interface keyword to display only the bridge domain that contains the specified interface as an attachment circuit. In the sample output, only the attachment circuit matches the filter that is displayed. No pseudowires are displayed.

Note

For Cisco IOS XR software Release 5.1.2 and above, you can filter the command output for a specific pseudowire with just the pseudowire ID. However, in case of configurations with BGP Auto-discovery with BGP or LDP signaling (in VPLS), you can specify the pseudowire only with the combination of the neighbor filter and the pseudowire ID.

Task ID


Task ID	Operations
l2vpn	read

Examples

This is the sample output for show l2vpn bridge-domain command with VxLAN parameters configured:


RP/0/RP0/CPU0:router# show l2vpn bridge-domain bd-name bg1_bd1 detail 
Legend: pp = Partially Programmed.
Bridge group: bg1, bridge-domain: bg1_bd1, id: 0, state: up, ShgId: 0, MSTi: 0
  Coupled state: disabled
  MAC learning: enabled
  MAC withdraw: enabled
    MAC withdraw for Access PW: enabled
    MAC withdraw sent on: bridge port up
    MAC withdraw relaying (access to access): disabled
  Flooding:
    Broadcast & Multicast: enabled
    Unknown unicast: enabled
  MAC aging time: 300 s, Type: inactivity
  MAC limit: 4000, Action: none, Notification: syslog
  MAC limit reached: no
  MAC port down flush: enabled
  MAC Secure: disabled, Logging: disabled
  Split Horizon Group: none
  Dynamic ARP Inspection: disabled, Logging: disabled
  IP Source Guard: disabled, Logging: disabled
  DHCPv4 snooping: disabled
  IGMP Snooping: enabled
  IGMP Snooping profile: none
  MLD Snooping profile: none
  Storm Control: disabled
  Bridge MTU: 1500
  MIB cvplsConfigIndex: 1
  Filter MAC addresses:
  P2MP PW: disabled
  Create time: 30/03/2015 22:25:38 (00:26:08 ago)
  No status change since creation
  ACs: 2 (2 up), VFIs: 1, PWs: 0 (0 up), PBBs: 0 (0 up)
  List of ACs:
    AC: BVI1, state is up
      Type Routed-Interface
      MTU 1514; XC ID 0x80000001; interworking none
      BVI MAC address:
        1000.4444.0001
    AC: GigabitEthernet0/8/0/0.1, state is up
      Type VLAN; Num Ranges: 1
      Outer Tag: 1
      VLAN ranges: [1001, 1001]
      MTU 1508; XC ID 0x508000a; interworking none
      MAC learning: enabled
      Flooding:
        Broadcast & Multicast: enabled
        Unknown unicast: enabled
      MAC aging time: 300 s, Type: inactivity
      MAC limit: 4000, Action: none, Notification: syslog
      MAC limit reached: no
      MAC port down flush: enabled
      MAC Secure: disabled, Logging: disabled
      Split Horizon Group: none
      Dynamic ARP Inspection: disabled, Logging: disabled
      IP Source Guard: disabled, Logging: disabled
      DHCPv4 snooping: disabled
      IGMP Snooping: enabled
      IGMP Snooping profile: none
      MLD Snooping profile: none
      Storm Control: bridge-domain policer
      Static MAC addresses:
      
      Storm control drop counters: 
        packets: broadcast 0, multicast 0, unknown unicast 0 
        bytes: broadcast 0, multicast 0, unknown unicast 0 
      Dynamic ARP inspection drop counters: 
        packets: 0, bytes: 0
      IP source guard drop counters: 
        packets: 0, bytes: 0
  List of VNIs:
    VNI 1, state is up
      XC ID 0x80000014
      Encap type VXLAN
      Overlay nve100, Source 1.1.1.1, Multicast Group 225.1.1.1, UDP Port 4789
      Anycast VTEP 100.1.1.1, Anycast Multicast Group 224.10.10.1
      MAC learning: enabled
      Flooding:
        Broadcast & Multicast: enabled
        Unknown unicast: enabled
      MAC aging time: 300 s, Type: inactivity
      MAC limit: 4000, Action: none, Notification: syslog
      MAC limit reached: no
      MAC port down flush: enabled
      MAC Secure: disabled, Logging: disabled
      Split Horizon Group: none
      Dynamic ARP Inspection: disabled, Logging: disabled
      IP Source Guard: disabled, Logging: disabled
      DHCPv4 snooping: disabled
      IGMP Snooping: enabled
      IGMP Snooping profile: none
      MLD Snooping profile: none
      Storm Control: bridge-domain policer
      
  List of Access PWs:
  List of VFIs:
    VFI bg1_bd1_vfi (up)
      VFI Statistics:
        drops: illegal VLAN 0, illegal length 0

This table describes the significant fields shown in the display.

The following sample output shows information for the bridge ports such as attachment circuits and pseudowires for the specific bridge domains:


RP/0/RP0/CPU0:router# show l2vpn bridge-domain

Bridge group: g1, bridge-domain: bd1, id: 0, state: up, ShgId: 0, MSTi: 0
  Aging: 300 s, MAC limit: 4000, Action: none, Notification: syslog
  Filter MAC addresses: 0
  ACs: 1 (1 up), VFIs: 1, PWs: 1 (1 up)
  List of ACs:
    Gi0/1/0/0, state: up, Static MAC addresses: 2, MSTi: 0 (unprotected)
  List of Access PWs:
  List of VFIs:
    VFI 1
      Neighbor 10.1.1.1 pw-id 1, state: up, Static MAC addresses: 0

This table describes the significant fields shown in the display.

Table 1. show l2vpn bridge-domain Command Field Descriptions
Field	Description
Bridge group	Name of bridge domain group is displayed.
bridge-domain	Name of bridge domain is displayed.
id	ID assigned to this bridge domain is displayed.
state	Current state of the bridge domain is displayed.

The following example shows sample output for a bridge named bd1:


RP/0/RP0/CPU0:router# show l2vpn bridge-domain bd-name bd1

Bridge group: g1, bridge-domain: bd1, id: 0, state: up, ShgId: 0, MSTi: 0
  Aging: 300 s, MAC limit: 4000, Action: none, Notification: syslog
  Filter MAC addresses: 0
  ACs: 1 (1 up), VFIs: 1, PWs: 1 (1 up)
  List of ACs:
    Gi0/1/0/0, state: up, Static MAC addresses: 2, MSTi: 0 (unprotected)
  List of Access PWs:
  List of VFIs:
    VFI 1
      Neighbor 10.1.1.1 pw-id 1, state: up, Static MAC addresses: 0

The following sample output shows brief information about the bridges:


RP/0/RP0/CPU0:router# show l2vpn bridge-domain brief

Bridge Group/Bridge-Domain Name  ID    State      Num ACs/up     Num PWs/up
-------------------------------- ----- ---------- -------------- --------------
g1/bd1                           0     up         1/1            1/1

This table describes the significant fields shown in the display.

Table 2. show l2vpn bridge-domain brief Command Field Descriptions
Field	Description
Bridge Group/Bridge-Domain Name	Bridge domain group name followed by the bridge domain name are displayed.
ID	ID assigned to this bridge domain is displayed.
State	Current state of the bridge domain is displayed.
Num ACs/up	Total number of attachment circuits that are up in this bridge domain is displayed.
Num PWs/up	Total number of pseudowires that are up in this bridge domain is displayed. The count includes both VFI pseudowires and access pseudowires.

The following sample output shows detailed information:


RP/0/RP0/CPU0:router# show l2vpn bridge-domain detail

Bridge group: g1, bridge-domain: bd1, id: 0, state: up, ShgId: 0, MSTi: 0
  MAC learning: enabled
  MAC withdraw: disabled
  Flooding:
    Broadcast & Multicast: enabled
    Unknown unicast: enabled
  MAC aging time: 300 s, Type: inactivity
  MAC limit: 4000, Action: none, Notification: syslog
  MAC limit reached: yes
  Security: disabled
  DHCPv4 snooping: disabled
  MTU: 1500
  Filter MAC addresses:
  ACs: 1 (1 up), VFIs: 1, PWs: 1 (1 up)
  List of ACs:
    AC: GigabitEthernet0/1/0/0, state is up
      Type Ethernet
      MTU 1500; XC ID 0x2000001; interworking none; MSTi 0 (unprotected)
      MAC learning: enabled
      Flooding:
        Broadcast & Multicast: enabled
        Unknown unicast: enabled
      MAC aging time: 300 s, Type: inactivity
      MAC limit: 4000, Action: none, Notification: syslog
      MAC limit reached: yes
      Security: disabled
      DHCPv4 snooping: disabled
      Static MAC addresses:
        0000.0000.0000
        0001.0002.0003
      Statistics:
        packet totals: receive 3919680,send 9328
        byte totals: receive 305735040,send 15022146
  List of Access PWs:
  List of VFIs:
    VFI 1
      PW: neighbor 1.1.1.1, PW ID 1, state is up ( established )
        PW class mpls, XC ID 0xff000001
        Encapsulation MPLS, protocol LDP
        PW type Ethernet, control word disabled, interworking none
        PW backup disable delay 0 sec
        Sequencing not set
                MPLS         Local                          Remote                        
          ------------ ------------------------------ -------------------------
          Label        16003                          16003                         
          Group ID     0x0                            0x0                           
          Interface    1                              1                             
          MTU          1500                           1500                          
          Control word disabled                       disabled                      
          PW type      Ethernet                       Ethernet                      
          VCCV CV type 0x2                            0x2                           
                       (LSP ping verification)        (LSP ping verification)       
          VCCV CC type 0x2                            0x2                           
                       (router alert label)           (router alert label)          
          ------------ ------------------------------ -------------------------
        Create time: 12/03/2008 14:03:00 (17:17:30 ago)
        Last time status changed: 13/03/2008 05:57:58 (01:22:31 ago)
        MAC withdraw message: send 0 receive 0
        Static MAC addresses:
        Statistics:
          packet totals: receive 3918814, send 3918024
          byte totals: receive 305667492, send 321277968
      VFI Statistics:
        drops: illegal VLAN 0, illegal length 0

The following sample output shows that when a bridge operates in VPWS mode, the irrelevant information for MAC learning is suppressed:


RP/0/RP0/CPU0:router# show l2vpn bridge-domain detail

Bridge group: foo_group, bridge-domain: foo_bd, id: 0, state: up, ShgId: 0
  VPWS Mode
  MTU: 1500
  ACs: 1 (0 up), VFIs: 1, PWs: 2 (2 up)
  List of ACs:
    AC: GigabitEthernet0/5/1/4, state is admin down
      Type Ethernet      MTU 1500; XC ID 1; interworking none
    Static MAC addresses:
      Statistics:
        packet totals: receive 0,send 0
        byte totals: receive 0,send 0
  List of VFIs:
    VFI foo_vfi
      PW: neighbor 1.1.1.1, PW ID 1, state is up ( established )
        PW class not set
        Encapsulation MPLS, protocol LDP
        PW type Ethernet, control word enabled, interworking none
        Sequencing not set
          MPLS         Local                          Remote                        
          ------------ ------------------------------ ------------------------------
          Label        16001                          16001
          Group ID   unassigned                   unknown                       
          Interface    siva/vfi                       siva/vfi                      
          MTU          1500                           1500                          
          Control word enabled                        enabled                       
          PW type      Ethernet                       Ethernet                      
          VCCV CV type 0x2                            0x2                           
                       (LSP ping verification)        (LSP ping verification)       
          VCCV CC type 0x3                            0x3                           
                      (control word)                 (control word)                
                       (router alert label)           (router alert label)          
          ------------ ------------------------------ ------------------------------
        Create time: 25/06/2007 05:29:42 (2w0d ago)
        Last time status changed: 27/06/2007 06:50:35 (1w5d ago)
      Static MAC addresses:
      PW: neighbor 1.1.1.1, PW ID 2, state is up ( established )
        PW class not set
        Encapsulation MPLS, protocol LDP
        PW type Ethernet, control word enabled, interworking none
        Sequencing not set
          MPLS         Local                          Remote                        
          ------------ ------------------------------ ------------------------------
          Label        16002                          16002                         
          Group ID     unassigned                     unknown                       
          Interface    siva/vfi                       siva/vfi                      
          MTU          1500                           1500                          
          Control word enabled                        enabled                       
          PW type      Ethernet                       Ethernet                      
          VCCV CV type 0x2                            0x2                           
                       (LSP ping verification)        (LSP ping verification)       
          VCCV CC type 0x3                            0x3                           
                      (control word)                 (control word)                
                       (router alert label)           (router alert label)          
          ------------ ------------------------------ ------------------------------
        Create time: 25/06/2007 05:29:42 (2w0d ago)
        Last time status changed: 27/06/2007 06:50:35 (1w5d ago)
      Static MAC addresses:
      Statistics:
        drops: illegal VLAN 0, illegal length 0

This table describes the significant fields shown in the display.

Table 3. show l2vpn bridge-domain detail Command Field Descriptions
Field	Description
Bridge group	Name of bridge domain group is displayed.
bridge-domain	Name of bridge domain is displayed.
ID	ID assigned to this bridge domain is displayed.
state	Current state of the bridge domain is displayed.
MSTi	ID for the Multiple Spanning Tree.

The following sample output shows filter information about the bridge-domain group named g1:


RP/0/RP0/CPU0:router# show l2vpn bridge-domain group g1

Bridge group: g1, bridge-domain: bd1, id: 0, state: up, ShgId: 0, MSTi: 0
  Aging: 300 s, MAC limit: 4000, Action: none, Notification: syslog
  Filter MAC addresses: 0
  ACs: 1 (1 up), VFIs: 1, PWs: 1 (1 up)
  List of ACs:
    Gi0/1/0/0, state: up, Static MAC addresses: 2, MSTi: 0 (unprotected)
  List of Access PWs:
  List of VFIs:
    VFI 1
      Neighbor 1.1.1.1 pw-id 1, state: up, Static MAC addresses: 0

The following sample output shows display the filter information for the interface on the bridge domain:


RP/0/RP0/CPU0:router# show l2vpn bridge-domain interface gigabitEthernet 0/1/0/0

Bridge group: g1, bridge-domain: bd1, id: 0, state: up, ShgId: 0, MSTi: 0
  Aging: 300 s, MAC limit: 4000, Action: none, Notification: syslog
  Filter MAC addresses: 0
  ACs: 1 (1 up), VFIs: 1, PWs: 1 (1 up)
  List of ACs:
    Gi0/1/0/0, state: up, Static MAC addresses: 2, MSTi: 0 (unprotected)

The following sample output shows that the bridge domain contains the pseudowires to match the filter for the neighbor:


RP/0/RP0/CPU0:router# show l2vpn bridge-domain neighbor 1.1.1.1

Bridge group: g1, bridge-domain: bd1, id: 0, state: up, ShgId: 0, MSTi: 0
  Aging: 300 s, MAC limit: 4000, Action: none, Notification: syslog
  Filter MAC addresses: 0
  ACs: 1 (1 up), VFIs: 1, PWs: 1 (1 up)
  List of Access PWs:
  List of VFIs:
    VFI 1
      Neighbor 1.1.1.1 pw-id 1, state: up, Static MAC addresses: 0

The following sample output shows the summary information for the bridge domain:


RP/0/RP0/CPU0:router# show l2vpn bridge-domain summary

Number of groups: 1, bridge-domains: 1, Up: 1, Shutdown: 0
Number of ACs: 1 Up: 1, Down: 0
Number of PWs: 1 Up: 1, Down: 0

This example shows the sample output of a configured flow label:


RP/0/RP0/CPU0:router# show l2vpn bridge-domain detail
Bridge group: g1, bridge-domain: d1, id: 0, state: up, ShgId: 0, MSTi: 0
 ……
  PW: neighbor 3.3.3.3, PW ID 2, state is up ( established )
    PW class class1, XC ID 0x1000002
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word disabled, interworking none
    PW backup disable delay 0 sec
		Sequencing not set
    Flow label flags configured (Rx=1,Tx=1), negotiated (Rx=0,Tx=1)

This table describes the significant fields shown in the display.

Table 4. show l2vpn bridge-domain summary Command Field Descriptions
Field	Description
Number of groups	Number of configured bridge domain groups is displayed.
bridge-domains	Number of configured bridge domains is displayed.
Shutdown	Number of bridge domains that are in Shutdown state is displayed.
Number of ACs	Number of attachment circuits that are in Up state and Down state are displayed.
Number of PWs	Number of pseudowires that are in Up state and Down state are displayed. This includes the VFI pseudowire and the access pseudowire.

Related Commands


Command	Description
clear l2vpn bridge-domain (VPLS)	Clears the MAC addresses and restarts the bridge domains on the router.

show l2vpn forwarding bridge-domain (VPLS)

To display information on the bridge that is used by the forwarding layer, use the show l2vpn forwarding bridge-domain command in EXEC mode.

show l2vpn forwarding bridge-domain [bridge-domain-name] {detail | hardware {egress | ingress}} location node-id

Syntax Description


`bridge-domain-name`	(Optional) Name of a bridge domain.
detail	Displays all the detailed information on the attachment circuits and pseudowires.
hardware	Displays the hardware location entry.
egress	Reads information from the egress PSE.
ingress	Reads information from the ingress PSE.
location `node-id`	Displays the bridge-domain information for the specified location. The `node-id` argument is entered in the rack/slot/module notation.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

For each bridge, you can display summary information about the number of bridge ports, number of MAC addresses, configured VXLANs and so forth.

The detail keyword displays detailed information on the attachment circuits and pseudowires, and is meant for field investigation by a specialized Cisco engineer.

Note

All bridge ports in the bridge domain on that line card are displayed. Therefore, if the bridge domain contains non-local bridge ports, those are displayed as well.

Task ID


Task ID	Operations
l2vpn	read

Examples

The following sample output shows bridge-domain information for location 0/1/CPU0:


RP/0/RP0/CPU0:router# show l2vpn forwarding bridge-domain location 0/1/CPU0

Bridge-Domain Name               ID     Ports addr   Flooding Learning State    
-------------------------------- ------ ----- ------ -------- -------- ---------
g1:bd1

Bridge-domain name: g1:bd1, id: 0, state: up
 MAC learning: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: yes
 Security: disabled
 DHCPv4 snooping: profile not known on this node
 Bridge MTU: 1500 bytes
 Number of bridge ports: 2
 Number of MAC addresses: 65536
 Multi-spanning tree instance: 0

  GigabitEthernet0/1/0/0, state: oper up
    Number of MAC: 32770
    Sent(Packets/Bytes): 0/21838568
    Received(Packets/Bytes): 5704781/444972918

  Nbor 1.1.1.1 pw-id 1
    Number of MAC: 32766
    Sent(Packets/Bytes): 0/0
    Received(Packets/Bytes): 5703987/444910986
            0      2     65536  Enabled  Enabled  UP

The following sample output shows detailed information for hardware location 0/1/CPU0 from the egress pse:


RP/0/RP0/CPU0:router

Bridge-domain name: g1:bd1, id: 0, state: up
 MAC learning: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: yes
 Security: disabled
 DHCPv4 snooping: profile not known on this node
 Bridge MTU: 1500 bytes
 Number of bridge ports: 2
 Number of MAC addresses: 65536
 Multi-spanning tree instance: 0

================ GSR HW Information ================ 

-----------------------------------------------
           SHG-TX rewrite details              
-----------------------------------------------
-----------------------------------------------
 HW Rewrite 0 Detail :
-----------------------------------------------
    Rewrite HW Address  : 0x00060000  
    packets 0  bytes 0 
 Raw data:
[ 0x04018180 04018190 040181a0 040181b0 ]
[ 0x04018170 00000000 80360000 000bfff4 ]
[ 0x00000000 00000000 00000000 00000000 ] 

-----------------------------------------------
           SHG-TX encap details                
-----------------------------------------------
outer_etype:                   0
outer_vlan_id:                 0
gather_profile:                0
inner_vlan_id:                 0
so_l2_len_adjust:              0
-----------------------------------------------
           SHG-TX mgid details                 
-----------------------------------------------
          Base MGIDs for default mgid          
base_mgid[0]:             0x0003fffb
base_mgid[1]:             0x0003fffb
base_mgid[2]:             0x0003fffb
base_mgid[3]:             0x0003fffb
base_mgid[4]:             0x0003fffb
base_mgid[5]:             0x0003fffb
base_mgid[6]:             0x0003fffb
base_mgid[7]:             0x0003fffb
         MGID Entries for default mgid         
oi[0]:             0
oq[0]:             16384
xc_id[0]:          1
mgid_idx[0]:       0x00000000
next_mgid[0]:      0x00000000
-----------------------------------------------
 VMR 0 Details
-----------------------------------------------
vmrid: 0x5f002010
Value: 0xc0 0x00 0x1f 0xff 0xff 0xff 0xff 0xff 0xfd 
Mask : 0x00 0x00 0x1f 0xff 0xff 0xff 0xff 0xff 0xe0 
Result 0x32003000
==================================================== 

  GigabitEthernet0/1/0/0, state: oper up
    Number of MAC: 32770
    Sent(Packets/Bytes): 749/22989834
    Received(Packets/Bytes): 5732104/447104112

================ GSR HW Information ================ 

-----------------------------------------------
           BP-TX-AC rewrite details            
-----------------------------------------------

 BP is local


-----------------------------------------------
 BP L2 Uidb Details
-----------------------------------------------
l2fwd_enabled:                  true
plim_enabled:                   true
l2fwd_type:                     4
l2_ac_type:                     0
xconn_id:                       0
bridge_id:                      0
shg id:                         0
unicast flooding enabled:       0
multicast flooding enabled:     0
broadcast flooding enabled:     0
mac learning enabled:           0
Is AC Port mode?:           0
-----------------------------------------------
 HW Rewrite 0 Detail :
-----------------------------------------------
    Rewrite HW Address  : 0x59eff314  
    packets 0  bytes 0 
    HFA Bits 0x0 gp 0 mtu 1580  (REW)  
    OI 0x3fffc OutputQ 0 Output-port 0x36 local_outputq 0x0 
 Raw data:
[ 0x00000000 0036062c 0003fffc 00000000 ]
[ 0x00000000 00000000 0d103600 00000010 ]
[ 0x00000000 00000000 00000000 00000000 ] 

-----------------------------------------------
 BP OI/OQ Details
-----------------------------------------------
oi[0]:         0x00000000        oq[0]            16384
oi[1]:         0x00000000        oq[1]            65535
oi[2]:         0x00000000        oq[2]            65535
oi[3]:         0x00000000        oq[3]            65535
oi[4]:         0x00000000        oq[4]            65535
oi[5]:         0x00000000        oq[5]            65535
oi[6]:         0x00000000        oq[6]            65535
oi[7]:         0x00000000        oq[7]            65535
-----------------------------------------------
 Sram table entry details
-----------------------------------------------
sram_data: 0xa000400c
==================================================== 

  Nbor 1.1.1.1 pw-id 1
    Number of MAC: 32766
    Sent(Packets/Bytes): 0/0
    Received(Packets/Bytes): 5731250/447037500

================ GSR HW Information ================ 

-----------------------------------------------
           BP-TX-AC rewrite details            
-----------------------------------------------
-----------------------------------------------
 BP OI/OQ Details
-----------------------------------------------
oi[0]:         0x00000000        oq[0]            65535
oi[1]:         0x00000000        oq[1]            65535
oi[2]:         0x00000000        oq[2]            65535
oi[3]:         0x00000000        oq[3]            65535
oi[4]:         0x00000000        oq[4]            65535
oi[5]:         0x00000000        oq[5]            65535
oi[6]:         0x00000000        oq[6]            65535
oi[7]:         0x00000000        oq[7]            65535
-----------------------------------------------
 BP Encap Info
-----------------------------------------------
mac_length:   0
mac_string:     
egress_slot:  2
num_tags:     1
 tags:        {16001, }
if_handle:    0x03000500
====================================================

The following sample output shows the bridge-domain information for the specified location:


RP/0/RP0/CPU0:router# show l2vpn forwarding bridge-domain g1:bd1 location 0/1/CPU0

Bridge-Domain Name               ID     Ports addr   Flooding Learning State    
-------------------------------- ------ ----- ------ -------- -------- ---------
g1:bd1                           0      2     65536  Enabled  Enabled  UP

The following sample output shows the hardware information for a specific bridge-domain:


RP/0/RP0/CPU0:router#show l2vpn bridge-domain hardware

Bridge group: aa, bridge-domain name: g1, id:0
  FGID Boardcast [version 1]: 
   Allocate_count: 2048, Retry_count: 0, Realloc_on: Off
   Status_flag: (0x4) Replay-end
   ALL 44032, VFI 44033
 
Bridge group: aa, bridge-domain name: g2, id:1
  FGID Boardcast [version 1]: 
   Allocate_count: 2048, Retry_count: 0, Realloc_on: Off
   Status_flag: (0x4) Replay-end
   ALL 44034, VFI 44035

The following sample output shows the hardware information for the line card, for a specific bridge-domain on the ingress detail location:


RP/0/RP0/CPU0:router#
show l2vpn forwarding bridge-domain hardware ingress detail location 0/2/CPU0

Bridge-domain name: aa:g1, id: 0, state: up
 MAC learning: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: no
 Security: disabled
 DHCPv4 snooping: profile not known on this node
 Bridge MTU: 1500 bytes
 Number of bridge ports: 4
 Number of MAC addresses: 0
 Multi-spanning tree instance: 0
 
  INGRESS BRIDGE [version, state]: [1, CREATED]
 
        TCAM entry seq#: 1024 Key: [BID: 0 MAC: default]
        HW: 0x4c000000 0x000080ac 0x00010000 0x80ac0100
        SW: 0x4c000000 0x000080ac 0x00010000 0x80ac0100
 
        SMAC:  action: PUNT  state: NO REFRESH
        DMAC:  action: FLOOD, flood_enable: enable
        FGID:  All: 44032, VFI: 44033, MCAST_Sponge_q: 16
        Fabric_multicast1: 1 Fabric_multicast2: 1
 
        Admin State: UP
        MTU: 1500
        Number of MAC addresses: 1 (0 MAC + 1 default)
        ACL NAME (ACL-ID): VPLS Special (4096)
        TCAM region handle : 5
 

  GigabitEthernet0/2/0/1.1, state: oper up
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
 
  INGRESS BRIDGE PORT [version, state]: [1, BOUND]
        Bridge Port Type: AC
        XID: 0/2/CPU0 : 1 (0x1280001)
        Bridge ID: 0, Split Horizon ID: 0
        RX TLU1   : 0x4c00
        RX TLU2   : 0x1013c00
        RX TLU3   : 0x200ba00
        RX TLU4   : 0x3000c00
 
   INGRESS AC [version, state]: [1, BOUND]
 
        Xconnect-ID: [1] TCAM-Key: (UIDB:0x2 O-vlan:1 I-vlan:0 Ether-Type:0x8100)
        HW: 0x24001000 0x01280001 0x10128000 0xc7ff7d00
        SW: 0x24001000 0x01280001 0x10128000 0xc7ff7d00
 
        Service type: 4 (bridging pmp)
        Entry type: 1 (fwd)
        Bridge_ID : 0 
        ACL_ID : 4096 
        Xconnect_ID : 0x1280001
        SplitHorizonGroup_ID : 0 
        Rewrite supported: 0 (No)
        PW_mode: 0 (vc-type 5)
        AC-type: 1 (vlan-mode)
        Interface handle: 0x128000
        Ingress AC stats: 0x7ff7d
 
        SMAC Learning: enable
        DMAC Flooding: enable
 
  GigabitEthernet0/2/0/1.2, state: oper up
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
 
  INGRESS BRIDGE PORT [version, state]: [1, BOUND]
        Bridge Port Type: AC
        XID: 0/2/CPU0 : 2 (0x1280002)
        Bridge ID: 0, Split Horizon ID: 0
        RX TLU1   : 0x4c01
        RX TLU2   : 0x1013c01
        RX TLU3   : 0x200ba01
        RX TLU4   : 0x3000c01
 
   INGRESS AC [version, state]: [1, BOUND]
 
        Xconnect-ID: [2] TCAM-Key: (UIDB:0x2 O-vlan:2 I-vlan:0 Ether-Type:0x8100)
        HW: 0x24001000 0x01280002 0x10128002 0xc7ff7a00
        SW: 0x24001000 0x01280002 0x10128002 0xc7ff7a00
 
        Service type: 4 (bridging pmp)
        Entry type: 1 (fwd)
        Bridge_ID : 0 
        ACL_ID : 4096 
        Xconnect_ID : 0x1280002
        SplitHorizonGroup_ID : 0 
        Rewrite supported: 0 (No)
        PW_mode: 0 (vc-type 5)
        AC-type: 1 (vlan-mode)
        Interface handle: 0x128002
        Ingress AC stats: 0x7ff7a
 
        SMAC Learning: enable
        DMAC Flooding: enable
 
  GigabitEthernet0/2/0/1.3, state: oper up
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
 
  INGRESS BRIDGE PORT [version, state]: [1, BOUND]
        Bridge Port Type: AC
        XID: 0/2/CPU0 : 3 (0x1280003)
        Bridge ID: 0, Split Horizon ID: 0
        RX TLU1   : 0x4c02
        RX TLU2   : 0x1013c02
        RX TLU3   : 0x200ba02
        RX TLU4   : 0x3000c02
 
   INGRESS AC [version, state]: [1, BOUND]
 
        Xconnect-ID: [3] TCAM-Key: (UIDB:0x2 O-vlan:3 I-vlan:0 Ether-Type:0x8100)
        HW: 0x24001000 0x01280003 0x10128004 0xc7ff7700
        SW: 0x24001000 0x01280003 0x10128004 0xc7ff7700
 
        Service type: 4 (bridging pmp)
        Entry type: 1 (fwd)
        Bridge_ID : 0 
        ACL_ID : 4096 
        Xconnect_ID : 0x1280003
        SplitHorizonGroup_ID : 0 
        Rewrite supported: 0 (No)
        PW_mode: 0 (vc-type 5)
        AC-type: 1 (vlan-mode)
        Interface handle: 0x128004
        Ingress AC stats: 0x7ff77
 
        SMAC Learning: enable
        DMAC Flooding: enable
 
  Nbor 5.0.0.5 pw-id 1
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
 

  INGRESS BRIDGE PORT [version, state]: [1, BOUND]
        Bridge Port Type: ATOM
        XID: 127/15/CPU0 : 1 (0xfff80001)
        Bridge ID: 0, Split Horizon ID: 1
        VC label: 16006
        Control-word supported: No

Bridge-domain name: aa:g2, id: 1, state: up
 MAC learning: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: no
 Security: disabled
 DHCPv4 snooping: profile not known on this node
 Bridge MTU: 1500 bytes
 Number of bridge ports: 2
 Number of MAC addresses: 0
 Multi-spanning tree instance: 0
 
  INGRESS BRIDGE [version, state]: [1, CREATED]
 
        TCAM entry seq#: 1025 Key: [BID: 1 MAC: default]
        HW: 0x4c000000 0x000080ac 0x02010000 0x80ac0300
        SW: 0x4c000000 0x000080ac 0x02010000 0x80ac0300
 
        SMAC:  action: PUNT  state: NO REFRESH
        DMAC:  action: FLOOD, flood_enable: enable
        FGID:  All: 44034, VFI: 44035, MCAST_Sponge_q: 16
        Fabric_multicast1: 1 Fabric_multicast2: 1
 
        Admin State: UP
        MTU: 1500
        Number of MAC addresses: 1 (0 MAC + 1 default)
        ACL NAME (ACL-ID): VPLS Special (4097)
        TCAM region handle : 5
 

  GigabitEthernet0/2/0/1.4, state: oper up
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
 
  INGRESS BRIDGE PORT [version, state]: [1, BOUND]
        Bridge Port Type: AC
        XID: 0/2/CPU0 : 4 (0x1280004)
        Bridge ID: 1, Split Horizon ID: 0
        RX TLU1   : 0x4c03
        RX TLU2   : 0x1013c03
        RX TLU3   : 0x200ba03
        RX TLU4   : 0x3000c03
 
   INGRESS AC [version, state]: [1, BOUND]
 
        Xconnect-ID: [4] TCAM-Key: (UIDB:0x2 O-vlan:4 I-vlan:0 Ether-Type:0x8100)
        HW: 0x24003001 0x01280004 0x10128006 0xc7ff7400
        SW: 0x24003001 0x01280004 0x10128006 0xc7ff7400
 
        Service type: 4 (bridging pmp)
        Entry type: 1 (fwd)
        Bridge_ID : 1 
        ACL_ID : 4097 
        Xconnect_ID : 0x1280004
        SplitHorizonGroup_ID : 0 
        Rewrite supported: 0 (No)
        PW_mode: 0 (vc-type 5)
        AC-type: 1 (vlan-mode)
        Interface handle: 0x128006
        Ingress AC stats: 0x7ff74
 
        SMAC Learning: enable
        DMAC Flooding: enable
 
  Nbor 5.0.0.5 pw-id 2
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0

  INGRESS BRIDGE PORT [version, state]: [1, BOUND]
        Bridge Port Type: ATOM
        XID: 127/15/CPU0 : 2 (0xfff80002)
        Bridge ID: 1, Split Horizon ID: 1
        VC label: 16008
        Control-word supported: No

The following sample output shows the hardware information of the route processor, for a specific bridge-domain on the ingress detail location:


RP/0/RP0/CPU0:router#show l2vpn forwarding bridge-domain hardware ingress detail location 0/RP0/CPU0

Bridge-domain name: aa:g1, id: 0, state: up
 MAC learning: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: no
 Security: disabled
 DHCPv4 snooping: profile not known on this node
 Bridge MTU: 1500 bytes
 Number of bridge ports: 4
 Number of MAC addresses: 0
 Multi-spanning tree instance: 0
 
   BRIDGE [version, state]: [1, CREATED]
        Bridge ID: 0
         FGID1: 44032   NodeCount: 1   Info_len: 24   XID_count: 4
         FGID2: 44033   NodeCount: 1   Info_len: 20   XID_count: 3
 
        FGID1 Membership list: 
         node-id: 0/2/CPU0 (0x21)   RSI: 0x25   XID_count: 4
          XID:  0x1280001       0x1280002       0x1280003       0xfff80001      
 
        FGID2 Membership list: 
         node-id: 0/2/CPU0 (0x21)   RSI: 0x25   XID_count: 3
          XID:  0x1280001       0x1280002       0x1280003       
 
  GigabitEthernet0/2/0/1.1, state: oper up
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
 
   AC [version, state]: [1, BOUND]
        XID: 0x1280001   RSI: 0x25   Bridging: TRUE
 

  GigabitEthernet0/2/0/1.2, state: oper up
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
 
   AC [version, state]: [1, BOUND]
        XID: 0x1280002   RSI: 0x25   Bridging: TRUE
 

  GigabitEthernet0/2/0/1.3, state: oper up
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
 
   AC [version, state]: [1, BOUND]
        XID: 0x1280003   RSI: 0x25   Bridging: TRUE
 

  Nbor 5.0.0.5 pw-id 1
    Number of MAC: 0
 

Bridge-domain name: aa:g2, id: 1, state: up
 MAC learning: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: no
 Security: disabled
 DHCPv4 snooping: profile not known on this node
 Bridge MTU: 1500 bytes
 Number of bridge ports: 2
 Number of MAC addresses: 0
 Multi-spanning tree instance: 0
 
   BRIDGE [version, state]: [1, CREATED]
        Bridge ID: 1
         FGID1: 44034   NodeCount: 1   Info_len: 16   XID_count: 2
         FGID2: 44035   NodeCount: 1   Info_len: 12   XID_count: 1
 
        FGID1 Membership list: 
         node-id: 0/2/CPU0 (0x21)   RSI: 0x25   XID_count: 2
          XID:  0x1280004       0xfff80002      
 
        FGID2 Membership list: 
         node-id: 0/2/CPU0 (0x21)   RSI: 0x25   XID_count: 1
          XID:  0x1280004       
 
  GigabitEthernet0/2/0/1.4, state: oper up
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
 
   AC [version, state]: [1, BOUND]
        XID: 0x1280004   RSI: 0x25   Bridging: TRUE
 

  Nbor 5.0.0.5 pw-id 2
    Number of MAC: 0

The following sample output shows the hardware information of the line card, for a specific bridge-domain on the egress detail location:


RP/0/RP0/CPU0:router#show l2vpn forwarding bridge-domain hardware egress detail location 0/2/CPU0

Bridge-domain name: aa:g1, id: 0, state: up
 MAC learning: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: no
 Security: disabled
 DHCPv4 snooping: profile not known on this node
 Bridge MTU: 1500 bytes
 Number of bridge ports: 4
 Number of MAC addresses: 0
 Multi-spanning tree instance: 0
 
  EGRESS BRIDGE [version, state]: [1, CREATED]
 
        BID: 0   Total_oif_count: 4
        AC:  oif_count: 3  head_ptr: 0x9ff6e4f8  tail_ptr: 0x9ff6e480
        PW:  oif_count: 1  head_ptr: 0x9ff6e570
 
        PLU RESULT Key[Bridge-ID: 0]
        HW: 0x04008000 0x000a01c0 0x00000000 0x00000000
        SW: 0x04008000 0x000a01c0 0x00000000 0x00000000
        Entry_type: 1
        OLIST pointer: 0xa01
        OLIST channel: 3
        OLIST count: 4
 
        OIF[0] seg_type: AC xid: 0x1280003 Gi0/2/0/1.3 (ifh: 0x1280042)
        TLU RESULT tlu_addr: 0x3000a01 ch: 3 seg_type: 1
        HW: 0x80000002 0x00ba0080 0x01280003 0x00000000
        SW: 0x80000002 0x00ba0080 0x01280003 0x00000000
        SHG: 0 
        UIDB: 2 
        XID: 0x1280003
        OLIST pointer: 0xba00
        OLIST channel: 2
 
        OIF[1] seg_type: AC xid: 0x1280002 Gi0/2/0/1.2 (ifh: 0x1280022)
        TLU RESULT tlu_addr: 0x200ba00 ch: 2 seg_type: 1
        HW: 0x80000002 0x000a00c0 0x01280002 0x00000000
        SW: 0x80000002 0x000a00c0 0x01280002 0x00000000
        SHG: 0 
        UIDB: 2 
        XID: 0x1280002
        OLIST pointer: 0xa00
        OLIST channel: 3
 
        OIF[2] seg_type: AC xid: 0x1280001 Gi0/2/0/1.1 (ifh: 0x1280002)
        TLU RESULT tlu_addr: 0x3000a00 ch: 3 seg_type: 1
        HW: 0x80000002 0x00ba0180 0x01280001 0x00000000
        SW: 0x80000002 0x00ba0180 0x01280001 0x00000000
        SHG: 0 
        UIDB: 2 
        XID: 0x1280001
        OLIST pointer: 0xba01
        OLIST channel: 2
 
        OIF[3] seg_type: PW xid: 0xfff80001 ecd_ptr: 0x5206
        TLU RESULT tlu_addr: 0x200ba01 ch: 2 seg_type: 0
        HW: 0x01005206 0x00000000 0xfff80001 0x03e86000
        SW: 0x01005206 0x00000000 0xfff80001 0x03e86000
        SHG: 1 
        XID: 0xfff80001
        OLIST pointer: 0x0
        OLIST channel: 0
        Control Word: Disabled
        VC label: 16006
        ECD/TLU1 pointer: 0x5206
 
  GigabitEthernet0/2/0/1.1, state: oper up
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
 
  EGRESS BRIDGE PORT [version, state]: [1, BOUND]
        Bridge Port Type: AC
        XID: 0/2/CPU0 : 1 (0x1280001)
        Bridge ID: 0, Split Horizon ID: 0
        RX TLU1   : 0x4c00
        RX TLU2   : 0x1013c00
        RX TLU3   : 0x200ba00
        RX TLU4   : 0x3000c00
 
   EGRESS AC [version, state]: [1, BOUND]
 
        Xconnect-ID: [1] TLU2-entry-addr: [0x200a001]
        HW: 0x8018b000 0x0000000b 0x00004001 0xfb7ba000
        SW: 0x8018b000 0x0000000b 0x00004001 0xfb7ba000
 
        Entry status: 1 (Fwd)
        AC_type: 1 (vlan-mode)
        Outer-vlan: 1
        Inner-vlan: 0
        Outer Ether Type: 0 (dot1q)
        AC_mtu: 1580
        Adjacency_type: 0
        Default EgressQ (SharqQ): 11
        PW mode: 0 (vc-type 5)
        Rewrite supported: 0 (No)
        Control-word supported: 0 (No)
        Egress AC stats: 0x7dbdd
 

  GigabitEthernet0/2/0/1.2, state: oper up
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
 
  EGRESS BRIDGE PORT [version, state]: [1, BOUND]
        Bridge Port Type: AC
        XID: 0/2/CPU0 : 2 (0x1280002)
        Bridge ID: 0, Split Horizon ID: 0
        RX TLU1   : 0x4c01
        RX TLU2   : 0x1013c01
        RX TLU3   : 0x200ba01
        RX TLU4   : 0x3000c01
 
   EGRESS AC [version, state]: [1, BOUND]
 
        Xconnect-ID: [2] TLU2-entry-addr: [0x200a002]
        HW: 0x8018b000 0x0000000b 0x00004002 0xfb7b4000
        SW: 0x8018b000 0x0000000b 0x00004002 0xfb7b4000
 
        Entry status: 1 (Fwd)
        AC_type: 1 (vlan-mode)
        Outer-vlan: 2
        Inner-vlan: 0
        Outer Ether Type: 0 (dot1q)
        AC_mtu: 1580
        Adjacency_type: 0
        Default EgressQ (SharqQ): 11
        PW mode: 0 (vc-type 5)
        Rewrite supported: 0 (No)
        Control-word supported: 0 (No)
        Egress AC stats: 0x7dbda
 

  GigabitEthernet0/2/0/1.3, state: oper up
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
 
  EGRESS BRIDGE PORT [version, state]: [1, BOUND]
        Bridge Port Type: AC
        XID: 0/2/CPU0 : 3 (0x1280003)
        Bridge ID: 0, Split Horizon ID: 0
        RX TLU1   : 0x4c02
        RX TLU2   : 0x1013c02
        RX TLU3   : 0x200ba02
        RX TLU4   : 0x3000c02
 
   EGRESS AC [version, state]: [1, BOUND]
 
        Xconnect-ID: [3] TLU2-entry-addr: [0x200a003]
        HW: 0x8018b000 0x0000000b 0x00004003 0xfb7ae000
        SW: 0x8018b000 0x0000000b 0x00004003 0xfb7ae000
 
        Entry status: 1 (Fwd)
        AC_type: 1 (vlan-mode)
        Outer-vlan: 3
        Inner-vlan: 0
        Outer Ether Type: 0 (dot1q)
        AC_mtu: 1580
        Adjacency_type: 0
        Default EgressQ (SharqQ): 11
        PW mode: 0 (vc-type 5)
        Rewrite supported: 0 (No)
        Control-word supported: 0 (No)
        Egress AC stats: 0x7dbd7
 

  Nbor 5.0.0.5 pw-id 1
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
 

  EGRESS BRIDGE PORT [version, state]: [1, BOUND]
        Bridge Port Type: ATOM
        XID: 127/15/CPU0 : 1 (0xfff80001)
        Bridge ID: 0, Split Horizon ID: 1
        VC label: 16006
        Control-word supported: No
 
 
 
Bridge-domain name: aa:g2, id: 1, state: up
 MAC learning: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: no
 Security: disabled
 DHCPv4 snooping: profile not known on this node
 Bridge MTU: 1500 bytes
 Number of bridge ports: 2
 Number of MAC addresses: 0
 Multi-spanning tree instance: 0
 
  EGRESS BRIDGE [version, state]: [1, CREATED]
 
        BID: 1   Total_oif_count: 2
        AC:  oif_count: 1  head_ptr: 0x9ff6e534  tail_ptr: 0x9ff6e534
        PW:  oif_count: 1  head_ptr: 0x9ff6e5ac
 
        PLU RESULT Key[Bridge-ID: 1]
        HW: 0x04004000 0x000a02c0 0x00000000 0x00000000
        SW: 0x04004000 0x000a02c0 0x00000000 0x00000000
        Entry_type: 1
        OLIST pointer: 0xa02
        OLIST channel: 3
        OLIST count: 2
 
        OIF[0] seg_type: AC xid: 0x1280004 Gi0/2/0/1.4 (ifh: 0x1280062)
        TLU RESULT tlu_addr: 0x3000a02 ch: 3 seg_type: 1
        HW: 0x80000002 0x00ba0280 0x01280004 0x00000000
        SW: 0x80000002 0x00ba0280 0x01280004 0x00000000
        SHG: 0 
        UIDB: 2 
        XID: 0x1280004
        OLIST pointer: 0xba02
        OLIST channel: 2
 
        OIF[1] seg_type: PW xid: 0xfff80002 ecd_ptr: 0x5200
        TLU RESULT tlu_addr: 0x200ba02 ch: 2 seg_type: 0
        HW: 0x01005200 0x00000000 0xfff80002 0x03e88000
        SW: 0x01005200 0x00000000 0xfff80002 0x03e88000
        SHG: 1 
        XID: 0xfff80002
        OLIST pointer: 0x0
        OLIST channel: 0
        Control Word: Disabled
        VC label: 16008
        ECD/TLU1 pointer: 0x5200
 
  GigabitEthernet0/2/0/1.4, state: oper up
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
 
  EGRESS BRIDGE PORT [version, state]: [1, BOUND]
        Bridge Port Type: AC
        XID: 0/2/CPU0 : 4 (0x1280004)
        Bridge ID: 1, Split Horizon ID: 0
        RX TLU1   : 0x4c03
        RX TLU2   : 0x1013c03
        RX TLU3   : 0x200ba03
        RX TLU4   : 0x3000c03
 
   EGRESS AC [version, state]: [1, BOUND]
 
        Xconnect-ID: [4] TLU2-entry-addr: [0x200a004]
        HW: 0x8018b000 0x0000000b 0x00004004 0xfb7a8000
        SW: 0x8018b000 0x0000000b 0x00004004 0xfb7a8000
 
        Entry status: 1 (Fwd)
        AC_type: 1 (vlan-mode)
        Outer-vlan: 4
        Inner-vlan: 0
        Outer Ether Type: 0 (dot1q)
        AC_mtu: 1580
        Adjacency_type: 0
        Default EgressQ (SharqQ): 11
        PW mode: 0 (vc-type 5)
        Rewrite supported: 0 (No)
        Control-word supported: 0 (No)
        Egress AC stats: 0x7dbd4
 

  Nbor 5.0.0.5 pw-id 2
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
 

  EGRESS BRIDGE PORT [version, state]: [1, BOUND]
        Bridge Port Type: ATOM
        XID: 127/15/CPU0 : 2 (0xfff80002)
        Bridge ID: 1, Split Horizon ID: 1
        VC label: 16008
        Control-word supported: No

This table describes the significant fields shown in the display.

Table 5. show l2vpn forwarding bridge-domain Command Field Descriptions
Field	Description
Bridge-Domain Name	Name of bridge domain is displayed.
Bridge ID	ID assigned to this bridge domain is displayed.
Ports	Number of ports that are part of this bridge domain is displayed.
MAC Addr	Number of MAC addresses that are learned on this bridge domain is displayed.
Flooding	Flooding of packets are displayed if they are enabled on this bridge domain.
Learning	Learning of MAC addresses are displayed if they are enabled on this bridge domain.
State	Current state of the bridge domain is displayed.

Related Commands


Command	Description
clear l2vpn bridge-domain (VPLS)	Clears the MAC addresses and restarts the bridge domains on the router.

show l2vpn forwarding bridge-domain mac-address (VPLS)

To display the summary information for the MAC address, use the show l2vpn forwarding bridge-domain mac-address command in EXEC mode.

show l2vpn forwarding bridge-domain [bridge-domain-name] mac-address {MAC-address | detail | hardware {egress | ingress} | interface type interface-path-id | neighbor address pw-id pw-id} location node-id

Syntax Description

bridge-domain-name

(Optional) Name of a bridge domain.

MAC-address

MAC address.

detail

Displays detailed information for the MAC address.

hardware

Reads information from the hardware.

egress

Reads information from the egress PSE.

ingress

Reads information from the ingress PSE.

interface

Displays the match for the attachment circuit subinterface.

type

Interface type. For more information, use the question mark (?) online help function.

interface-path-id

Physical interface or virtual interface.

Note

Use the show interfaces command to see a list of all interfaces currently configured on the router.

For more information about the syntax for the router, use the question mark (? ) online help function.

neighbor address

Displays the match for the neighbor IP address.

pw-id pw-id

Displays the match for the pseudowire ID.

location node-id

Displays the bridge-domain information for the MAC address of the specified location. The node-id argument is entered in the rack/slot/module notation.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.7.0	This command was introduced.
Release 3.7.2	This command was introduced.
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read

Examples

The following sample output shows the specified location of the bridge-domain name g1:bd1 for the MAC address:


RP/0/RP0/CPU0:router# show l2vpn forwarding bridge-domain g1:bd1 location 0/1/CPU0
                                 Bridge       MAC
Bridge-Domain Name               ID     Ports addr   Flooding Learning State    
-------------------------------- ------ ----- ------ -------- -------- ---------
g1:bd1                           0      2     65536  Enabled  Enabled  UP

The following sample output shows the list of MAC addresses that are learned on a specified bridge and summary information for the addresses:


RP/0/RP0/CPU0:router# show l2vpn forwarding bridge-domain mac-address location 0/1/CPU0

Mac Address    Type    Learned from/Filtered on    LC learned Age               
--------------------------------------------------------------------------------
0000.0000.0000 static  Gi0/1/0/0                   N/A        N/A               
0000.0001.0101 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.0102 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.0103 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.0104 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.0105 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.0106 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.0107 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.0108 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.0109 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.010a dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.010b dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.010c dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.010d dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.010e dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.010f dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.0110 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.0111 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s      
0000.0001.0112 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 22s   
....

The following sample output shows the MAC address on a specified interface on a specified bridge:


RP/0/RP0/CPU0:router# show l2vpn forwarding bridge-domain g1:bd1 mac-address 1.2.3 location 0/1/CPU0

Mac Address    Type    Learned from/Filtered on    LC learned Age               
--------------------------------------------------------------------------------
0001.0002.0003 static  Gi0/1/0/0                   N/A        N/A

The following sample output shows the hardware information from the egress pse:


RP/0/RP0/CPU0:router# show l2vpn forwarding bridge-domain g1:bd1 mac-address hardware egress location 0/1/CPU0

Mac Address    Type    Learned from/Filtered on    LC learned Age               
--------------------------------------------------------------------------------
0000.0000.0000 static  Gi0/1/0/0                   N/A        N/A               
0000.0001.0101 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.0102 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.0103 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.0104 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.0105 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.0106 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.0107 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.0108 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.0109 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.010a dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.010b dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.010c dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.010d dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.010e dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.010f dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.0110 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.0111 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.0112 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.0113 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s      
0000.0001.0114 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 24s   
...

The following sample output shows the MAC addresses that are learned on a specified pseudowire on a specified bridge:


RP/0/RP0/CPU0:router# show l2vpn forwarding bridge-domain mac-address neighbor 1.1.1.1 pw-id 1 location 0/1/CPU0

Mac Address    Type    Learned from/Filtered on    LC learned Age               
--------------------------------------------------------------------------------
0000.0003.0101 dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.0102 dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.0103 dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.0104 dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.0105 dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.0106 dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.0107 dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.0108 dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.0109 dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.010a dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.010b dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.010c dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.010d dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.010e dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.010f dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.0110 dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.0111 dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.0112 dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.0113 dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.0114 dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s      
0000.0003.0115 dynamic 1.1.1.1, 1                  0/1/CPU0   0d 0h 0m 30s 
...

The following sample output shows the detailed information for MAC addresses that are learned on a specified interface and on specified bridge of a specified interface card. The sample output lists all the MAC addresses, the learned location, and the current age.


RP/0/RP0/CPU0:router# show l2vpn forwarding bridge-domain g1:bd1 mac-address interface gigabitEthernet 0/1/0/0 location 0/1/CPU0

Mac Address    Type    Learned from/Filtered on    LC learned Age               
--------------------------------------------------------------------------------
0000.0000.0000 static  Gi0/1/0/0                   N/A        N/A               
0000.0001.0101 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.0102 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.0103 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.0104 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.0105 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.0106 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.0107 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.0108 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.0109 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.010a dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.010b dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.010c dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.010d dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.010e dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.010f dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.0110 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.0111 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.0112 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.0113 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s      
0000.0001.0114 dynamic Gi0/1/0/0                   0/1/CPU0   0d 0h 2m 14s

The following sample output shows the MAC address hardware information on the line card, for a specific bridge-domain on the ingress detail location:


RP/0/RP0/CPU0:router#show l2vpn forwarding bridge-domain mac hardware ingress detail location 0/2/CPU0

 
Bridge-domain name: aa:g1, id: 0, state: up
 MAC learning: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: no
 Security: disabled
 DHCPv4 snooping: profile not known on this node
 Bridge MTU: 1500 bytes
 Number of bridge ports: 4
 Number of MAC addresses: 10
 Multi-spanning tree instance: 0
 
  INGRESS BRIDGE [version, state]: [1, CREATED]
 
        TCAM entry seq#: 1024 Key: [BID: 0 MAC: default]
        HW: 0x4c000000 0x000080ac 0x00010000 0x80ac0100
        SW: 0x4c000000 0x000080ac 0x00010000 0x80ac0100
 
        SMAC:  action: PUNT  state: NO REFRESH
        DMAC:  action: FLOOD, flood_enable: enable
        FGID:  All: 44032, VFI: 44033, MCAST_Sponge_q: 16
        Fabric_multicast1: 1 Fabric_multicast2: 1
 
        Admin State: UP
        MTU: 1500
        Number of MAC addresses: 11 (10 MAC + 1 default)
        ACL NAME (ACL-ID): VPLS Special (4096)
        TCAM region handle : 5
 

  GigabitEthernet0/2/0/1.1, state: oper up
    Number of MAC: 10
    Statistics:
      packets: received 0, sent 121515
      bytes: received 0, sent 7290900
 
  INGRESS BRIDGE PORT [version, state]: [1, BOUND]
        Bridge Port Type: AC
        XID: 0/2/CPU0 : 1 (0x1280001)
        Bridge ID: 0, Split Horizon ID: 0
        RX TLU1   : 0x4c00
        RX TLU2   : 0x1013c00
        RX TLU3   : 0x200ba00
        RX TLU4   : 0x3000c00
 
   INGRESS AC [version, state]: [1, BOUND]
 
        Xconnect-ID: [1] TCAM-Key: (UIDB:0x2 O-vlan:1 I-vlan:0 Ether-Type:0x8100)
        HW: 0x24001000 0x01280001 0x10128000 0xc7ff7d00
        SW: 0x24001000 0x01280001 0x10128000 0xc7ff7d00
 
        Service type: 4 (bridging pmp)
        Entry type: 1 (fwd)
        Bridge_ID : 0 
        ACL_ID : 4096 
        Xconnect_ID : 0x1280001
        SplitHorizonGroup_ID : 0 
        Rewrite supported: 0 (No)
        PW_mode: 0 (vc-type 5)
        AC-type: 1 (vlan-mode)
        Interface handle: 0x128000
        Ingress AC stats: 0x7ff7d
 
        SMAC Learning: enable
        DMAC Flooding: enable
 
 Mac Address: 0000.0022.2222, LC learned: 0/2/CPU0
   Age: 0d 0h 0m 21s, Flag: local
 

  INGRESS MAC [version, state]: [1, CREATED]
 
        TCAM entry seq#: 0 Key: [BID: 0 MAC: 0000.0022.2222]
        HW: 0x22004c00 0x00000001 0x00000000 0x01280001
        SW: 0x22004c00 0x00000001 0x00000000 0x01280001
 
        SMAC:  action: FWD  state: REFRESH
        XID: 0/2/CPU0 : 1 (0x1280001)
        DMAC:  action: FWD, BridgePort type: AC
        SHG ID     : 0
        Entry Flag : FWD
        Entry Type : DYNAMIC
        Local Switching: enabled
        Next (tlu0) addr: 0x4c00
        Control-word supported: No
 
        Destination AC: Gi0/2/0/1.1 (ifh: 0x1280002)
 
        TLU1            : 0x4c00
        [HW: 0x00000000 0x00013c00 0x00000000 0x00000100]
             label:             0     num of labels:         0
             entry type:      FWD     next ptr:     0x00013c00
             num of entries:    1
             BGP next-hop:   0.0.0.0
 
        TLU2            : 0x1013c00
        [HW: 0x00000008 0x00000000 0x00001000 0x00ba0000]
             label1:            1     label2:            0
             num of labels:     1     next ptr: 0x0000ba00
 
        TLU3            : 0x200ba00
        [HW: 0x00010000 0x00000000 0x00000000 0x000c0000]
            num. entries  : 1
            num. labels   : 0
            label 1       : 0
            label 2       : 0
            next ptr      : 0xc00
 
        TLU4            : 0x3000c00
        [HW: 0x00000000 0x20082000 0x01280040 0x00020000]
            dest. addr    : 0x20
            sponge queue  : 130
            egress port   : 0x128004
            rp destined   : no
            rp drop       : no
            hash type     : 0
            uidb index    : 0x2
 
 Mac Address: 0000.0022.2223, LC learned: 0/2/CPU0
   Age: 0d 0h 0m 21s, Flag: local
 

  INGRESS MAC [version, state]: [1, CREATED]
 
        TCAM entry seq#: 1 Key: [BID: 0 MAC: 0000.0022.2223]
        HW: 0x22004c00 0x00000001 0x00000000 0x01280001
        SW: 0x22004c00 0x00000001 0x00000000 0x01280001
 
        SMAC:  action: FWD  state: REFRESH
        XID: 0/2/CPU0 : 1 (0x1280001)
        DMAC:  action: FWD, BridgePort type: AC
        SHG ID     : 0
        Entry Flag : FWD
        Entry Type : DYNAMIC
        Local Switching: enabled
        Next (tlu0) addr: 0x4c00
        Control-word supported: No
 
        Destination AC: Gi0/2/0/1.1 (ifh: 0x1280002)
 
        TLU1            : 0x4c00
        [HW: 0x00000000 0x00013c00 0x00000000 0x00000100]
             label:             0     num of labels:         0
             entry type:      FWD     next ptr:     0x00013c00
             num of entries:    1
             BGP next-hop:   0.0.0.0
 
        TLU2            : 0x1013c00
        [HW: 0x00000008 0x00000000 0x00001000 0x00ba0000]
             label1:            1     label2:            0
             num of labels:     1     next ptr: 0x0000ba00
 
        TLU3            : 0x200ba00
        [HW: 0x00010000 0x00000000 0x00000000 0x000c0000]
            num. entries  : 1
            num. labels   : 0
            label 1       : 0
            label 2       : 0
            next ptr      : 0xc00
 
        TLU4            : 0x3000c00
        [HW: 0x00000000 0x20082000 0x01280040 0x00020000]
            dest. addr    : 0x20
            sponge queue  : 130
            egress port   : 0x128004
            rp destined   : no
            rp drop       : no
            hash type     : 0
            uidb index    : 0x2
 
 Mac Address: 0000.0022.2224, LC learned: 0/2/CPU0
   Age: 0d 0h 0m 21s, Flag: local
 

  INGRESS MAC [version, state]: [1, CREATED]
 
        TCAM entry seq#: 2 Key: [BID: 0 MAC: 0000.0022.2224]
        HW: 0x22004c00 0x00000001 0x00000000 0x01280001
        SW: 0x22004c00 0x00000001 0x00000000 0x01280001
 
        SMAC:  action: FWD  state: REFRESH
        XID: 0/2/CPU0 : 1 (0x1280001)
        DMAC:  action: FWD, BridgePort type: AC
        SHG ID     : 0
        Entry Flag : FWD
        Entry Type : DYNAMIC
        Local Switching: enabled
        Next (tlu0) addr: 0x4c00
        Control-word supported: No
 
        Destination AC: Gi0/2/0/1.1 (ifh: 0x1280002)
 
        TLU1            : 0x4c00
        [HW: 0x00000000 0x00013c00 0x00000000 0x00000100]
             label:             0     num of labels:         0
             entry type:      FWD     next ptr:     0x00013c00
             num of entries:    1
             BGP next-hop:   0.0.0.0
 
        TLU2            : 0x1013c00
        [HW: 0x00000008 0x00000000 0x00001000 0x00ba0000]
             label1:            1     label2:            0
             num of labels:     1     next ptr: 0x0000ba00
 
        TLU3            : 0x200ba00
        [HW: 0x00010000 0x00000000 0x00000000 0x000c0000]
            num. entries  : 1
            num. labels   : 0
            label 1       : 0
            label 2       : 0
            next ptr      : 0xc00
 
        TLU4            : 0x3000c00
        [HW: 0x00000000 0x20082000 0x01280040 0x00020000]
            dest. addr    : 0x20
            sponge queue  : 130
            egress port   : 0x128004
            rp destined   : no
            rp drop       : no
            hash type     : 0
            uidb index    : 0x2
 
 Mac Address: 0000.0022.2225, LC learned: 0/2/CPU0
   Age: 0d 0h 0m 21s, Flag: local
 

  INGRESS MAC [version, state]: [1, CREATED]
 
        TCAM entry seq#: 3 Key: [BID: 0 MAC: 0000.0022.2225]
        HW: 0x22004c00 0x00000001 0x00000000 0x01280001
        SW: 0x22004c00 0x00000001 0x00000000 0x01280001
 
        SMAC:  action: FWD  state: REFRESH
        XID: 0/2/CPU0 : 1 (0x1280001)
        DMAC:  action: FWD, BridgePort type: AC
        SHG ID     : 0
        Entry Flag : FWD
        Entry Type : DYNAMIC
        Local Switching: enabled
        Next (tlu0) addr: 0x4c00
        Control-word supported: No
 
        Destination AC: Gi0/2/0/1.1 (ifh: 0x1280002)
 
        TLU1            : 0x4c00
        [HW: 0x00000000 0x00013c00 0x00000000 0x00000100]
             label:             0     num of labels:         0
             entry type:      FWD     next ptr:     0x00013c00
             num of entries:    1
             BGP next-hop:   0.0.0.0
 
        TLU2            : 0x1013c00
        [HW: 0x00000008 0x00000000 0x00001000 0x00ba0000]
             label1:            1     label2:            0
             num of labels:     1     next ptr: 0x0000ba00
 
        TLU3            : 0x200ba00
        [HW: 0x00010000 0x00000000 0x00000000 0x000c0000]
            num. entries  : 1
            num. labels   : 0
            label 1       : 0
            label 2       : 0
            next ptr      : 0xc00
 
        TLU4            : 0x3000c00
        [HW: 0x00000000 0x20082000 0x01280040 0x00020000]
            dest. addr    : 0x20
            sponge queue  : 130
            egress port   : 0x128004
            rp destined   : no
            rp drop       : no
            hash type     : 0
            uidb index    : 0x2
 
 Mac Address: 0000.0022.2226, LC learned: 0/2/CPU0
   Age: 0d 0h 0m 21s, Flag: local
 

  INGRESS MAC [version, state]: [1, CREATED]
 
        TCAM entry seq#: 4 Key: [BID: 0 MAC: 0000.0022.2226]
        HW: 0x22004c00 0x00000001 0x00000000 0x01280001
        SW: 0x22004c00 0x00000001 0x00000000 0x01280001
 
        SMAC:  action: FWD  state: REFRESH
        XID: 0/2/CPU0 : 1 (0x1280001)
        DMAC:  action: FWD, BridgePort type: AC
        SHG ID     : 0
        Entry Flag : FWD
        Entry Type : DYNAMIC
        Local Switching: enabled
        Next (tlu0) addr: 0x4c00
        Control-word supported: No
 
        Destination AC: Gi0/2/0/1.1 (ifh: 0x1280002)
 
        TLU1            : 0x4c00
        [HW: 0x00000000 0x00013c00 0x00000000 0x00000100]
             label:             0     num of labels:         0
             entry type:      FWD     next ptr:     0x00013c00
             num of entries:    1
             BGP next-hop:   0.0.0.0
 
        TLU2            : 0x1013c00
        [HW: 0x00000008 0x00000000 0x00001000 0x00ba0000]
             label1:            1     label2:            0
             num of labels:     1     next ptr: 0x0000ba00
 
        TLU3            : 0x200ba00
        [HW: 0x00010000 0x00000000 0x00000000 0x000c0000]
            num. entries  : 1
            num. labels   : 0
            label 1       : 0
            label 2       : 0
            next ptr      : 0xc00
 
        TLU4            : 0x3000c00
        [HW: 0x00000000 0x20082000 0x01280040 0x00020000]
            dest. addr    : 0x20
            sponge queue  : 130
            egress port   : 0x128004
            rp destined   : no
            rp drop       : no
            hash type     : 0
            uidb index    : 0x2
 
 Mac Address: 0000.0022.2227, LC learned: 0/2/CPU0
   Age: 0d 0h 0m 21s, Flag: local
 

  INGRESS MAC [version, state]: [1, CREATED]
 
        TCAM entry seq#: 5 Key: [BID: 0 MAC: 0000.0022.2227]
        HW: 0x22004c00 0x00000001 0x00000000 0x01280001
        SW: 0x22004c00 0x00000001 0x00000000 0x01280001
 
        SMAC:  action: FWD  state: REFRESH
        XID: 0/2/CPU0 : 1 (0x1280001)
        DMAC:  action: FWD, BridgePort type: AC
        SHG ID     : 0
        Entry Flag : FWD
        Entry Type : DYNAMIC
        Local Switching: enabled
        Next (tlu0) addr: 0x4c00
        Control-word supported: No
 
        Destination AC: Gi0/2/0/1.1 (ifh: 0x1280002)
 
        TLU1            : 0x4c00
        [HW: 0x00000000 0x00013c00 0x00000000 0x00000100]
             label:             0     num of labels:         0
             entry type:      FWD     next ptr:     0x00013c00
             num of entries:    1
             BGP next-hop:   0.0.0.0
 
        TLU2            : 0x1013c00
        [HW: 0x00000008 0x00000000 0x00001000 0x00ba0000]
             label1:            1     label2:            0
             num of labels:     1     next ptr: 0x0000ba00
 
        TLU3            : 0x200ba00
        [HW: 0x00010000 0x00000000 0x00000000 0x000c0000]
            num. entries  : 1
            num. labels   : 0
            label 1       : 0
            label 2       : 0
            next ptr      : 0xc00
 
        TLU4            : 0x3000c00
        [HW: 0x00000000 0x20082000 0x01280040 0x00020000]
            dest. addr    : 0x20
            sponge queue  : 130
            egress port   : 0x128004
            rp destined   : no
            rp drop       : no
            hash type     : 0
            uidb index    : 0x2
 
 Mac Address: 0000.0022.2228, LC learned: 0/2/CPU0
   Age: 0d 0h 0m 21s, Flag: local
 

  INGRESS MAC [version, state]: [1, CREATED]
 
        TCAM entry seq#: 6 Key: [BID: 0 MAC: 0000.0022.2228]
        HW: 0x22004c00 0x00000001 0x00000000 0x01280001
        SW: 0x22004c00 0x00000001 0x00000000 0x01280001
 
        SMAC:  action: FWD  state: REFRESH
        XID: 0/2/CPU0 : 1 (0x1280001)
        DMAC:  action: FWD, BridgePort type: AC
        SHG ID     : 0
        Entry Flag : FWD
        Entry Type : DYNAMIC
        Local Switching: enabled
        Next (tlu0) addr: 0x4c00
        Control-word supported: No
 
        Destination AC: Gi0/2/0/1.1 (ifh: 0x1280002)
 
        TLU1            : 0x4c00
        [HW: 0x00000000 0x00013c00 0x00000000 0x00000100]
             label:             0     num of labels:         0
             entry type:      FWD     next ptr:     0x00013c00
             num of entries:    1
             BGP next-hop:   0.0.0.0
 
        TLU2            : 0x1013c00
        [HW: 0x00000008 0x00000000 0x00001000 0x00ba0000]
             label1:            1     label2:            0
             num of labels:     1     next ptr: 0x0000ba00
 
        TLU3            : 0x200ba00
        [HW: 0x00010000 0x00000000 0x00000000 0x000c0000]
            num. entries  : 1
            num. labels   : 0
            label 1       : 0
            label 2       : 0
            next ptr      : 0xc00
 
        TLU4            : 0x3000c00
        [HW: 0x00000000 0x20082000 0x01280040 0x00020000]
            dest. addr    : 0x20
            sponge queue  : 130
            egress port   : 0x128004
            rp destined   : no
            rp drop       : no
            hash type     : 0
            uidb index    : 0x2
 
 Mac Address: 0000.0022.2229, LC learned: 0/2/CPU0
   Age: 0d 0h 0m 21s, Flag: local

Related Commands

Command	Description
show l2vpn forwarding bridge-domain (VPLS)	Displays information on the bridge that is used by the forwarding layer.

shutdown (Bridge Domain)

To shut down a bridge domain to bring the bridge and all attachment circuits and pseudowires under it to admin down state, use the shutdown command in L2VPN bridge group bridge domain configuration mode. To re-enable the bridge domain, use the no form of this command.

shutdown

no shutdown

Syntax Description

This command has no keywords or arguments.

Command Default

By default, the bridge is not shutdown.

Command Modes

L2VPN bridge group bridge domain configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

When a bridge domain is disabled, all VFIs associated with the bridge domain are disabled. You can still attach or detach members to or from the bridge domain as well as the VFIs associated with the bridge domain.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to disable the bridge domain named bar:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# shutdown

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.

shutdown (VFI)

To disable virtual forwarding interface (VFI), use the shutdown command in L2VPN bridge group bridge domain VFI configuration mode. To re-enable VFI, use the no form of this command.

shutdown

no shutdown

Syntax Description

This command has no keywords or arguments.

Command Default

By default, the VFI is not shutdown.

Command Modes

L2VPN bridge group bridge domain VFI configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to disable VFI:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# vfi v1
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-vfi)# shutdown

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
mpls static label (VPLS)	Configures the MPLS static labels and the static labels for the access pseudowire configuration.
neighbor (VPLS)	Adds an access pseudowire port to a bridge domain or a pseudowire to a bridge virtual forwarding interface (VFI).

static-address (VPLS)

To add static entries to the MAC address for filtering, use the static-address command in L2VPN bridge group bridge domain MAC configuration mode. To remove entries profiled by the combination of a specified entry information, use the no form of this command.

static-address MAC-address drop

no static-address MAC-address drop

Syntax Description


`MAC-address`	Static MAC address that is used to filter on the bridge domain.
drop	Drops all traffic that is going to the configured MAC address.

Command Default

No static MAC address is configured.

Command Modes

L2VPN bridge group bridge domain MAC configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to add static MAC entries in L2VPN bridge group bridge domain MAC configuration mode. This entry causes all packets with destination MAC address 1.1.1 to be dropped.


RP/0/RP0/CPU0:router# configure 
RP/0/RP0/CPU0:router(config)# l2vpn 
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# mac
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac)# static-address 1.1.1 drop

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
mac (VPLS)	Enters L2VPN bridge group bridge domain MAC configuration mode.

static-mac-address (VPLS)

To configure the static MAC address to associate a remote MAC address with a pseudowire or any other bridge interface, use the static-mac-address command in the appropriate L2VPN bridge group bridge domain configuration submode. To disable this feature, use the no form of this command.

static-mac-address MAC-address

no static-mac-address MAC-address

Syntax Description


`MAC-address`	Static address to add to the MAC address.

Command Default

None

Command Modes

L2VPN bridge group bridge domain VFI pseudowire configuration

L2VPN bridge group bridge domain attachment circuit configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to associate a remote MAC address with a pseudowire:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# vfi model
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-vfi)# neighbor 10.1.1.2 pw-id 1000
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-vfi-pw)# static-mac-address 1.1.1

The following example shows how to associate a GigabitEthernet interface from a bridge domain to static MAC address 1.1.1:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# interface GigabitEthernet 0/1/0/0
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-ac)# static-mac-address 1.1.1

The following example shows how to associate an access pseudowire to static MAC address 2.2.2:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# neighbor 10.1.1.2 pw-id 2000
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-pw)# static-mac-address 2.2.2

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
mpls static label (VPLS)	Configures the MPLS static labels and the static labels for the access pseudowire configuration.
neighbor (VPLS)	Adds an access pseudowire port to a bridge domain or a pseudowire to a bridge virtual forwarding interface (VFI).
vfi (VPLS)	Configures virtual forwarding interface (VFI) parameters.

time (VPLS)

To configure the maximum aging time, use the time command in L2VPN bridge group bridge domain MAC aging configuration mode. To disable this feature, use the no form of this command.

time seconds

no time seconds

Syntax Description


`seconds`	MAC address table entry maximum age. The range is from 300 to 30000 seconds. Aging time is counted from the last time that the switch saw the MAC address. The default value is 300 seconds.

Command Default

seconds : 300

Command Modes

L2VPN bridge group bridge domain MAC aging configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

If no packets are received from the MAC address for the duration of the maximum aging time, the dynamic MAC entry previously learned is removed from the forwarding table.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to increase the maximum aging time to 600 seconds. After 600 seconds of inactivity from a MAC address, the MAC address is removed form the forwarding table.


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# mac
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac)# aging
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac-aging)# time 600

Related Commands

Command	Description
aging (VPLS)	Enters the MAC aging configuration submode to set the aging parameters such as time and type.
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
mac (VPLS)	Enters L2VPN bridge group bridge domain MAC configuration mode.
type (VPLS)	Configures the type for MAC address aging.

type (VPLS)

To configure the type for MAC address aging, use the type command in L2VPN bridge group bridge domain MAC aging configuration mode. To disable this feature, use the no form of this command.

type {absolute | inactivity}

no type {absolute | inactivity}

Syntax Description


absolute	Configures the absolute aging type.
inactivity	Configures the inactivity aging type.

Command Default

By default, the inactivity type is configured.

Command Modes

L2VPN bridge group bridge domain MAC aging configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

In general, the type is set to inactivity. With an inactivity type configuration, a MAC address is removed from the forwarding table after the MAC address is inactive for the configured aging time.

With an absolute type configuration, a MAC address is always removed from the forwarding table after the aging time has elapsed once it is initially learned.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure the MAC address aging type to absolute for every member of the bridge domain named bar:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# mac
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac)# aging
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac-aging)# type absolute

Related Commands

Command	Description
aging (VPLS)	Enters the MAC aging configuration submode to set the aging parameters such as time and type.
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
mac (VPLS)	Enters L2VPN bridge group bridge domain MAC configuration mode.
time (VPLS)	Configures the maximum aging time.

vfi (VPLS)

To configure virtual forwarding interface (VFI) parameters and to enter L2VPN bridge group bridge domain VFI configuration mode, use the vfi command in L2VPN bridge group bridge domain configuration mode. To remove all configurations that are made under the specified VFI, use the no form of this command.

vfi vfi-name

no vfi vfi-name

Syntax Description


`vfi-name`	Name of the specified virtual forwarding interface.

Command Default

None

Command Modes

L2VPN bridge group bridge domain configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the vfi command to enter L2VPN bridge group bridge domain VFI configuration mode.

You cannot configure a pseudowire directly under a bridge domain. Therefore, a psuedowire must be configured under a VFI, which is configured under a bridge domain.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to create a VFI:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# vfi v1
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-vfi)#

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
mpls static label (VPLS)	Configures the MPLS static labels and the static labels for the access pseudowire configuration.
neighbor (VPLS)	Adds an access pseudowire port to a bridge domain or a pseudowire to a bridge virtual forwarding interface (VFI).

withdraw (VPLS)

To enable MAC address withdrawal for a specified bridge domain, use the withdraw command in L2VPN bridge group bridge domain MAC configuration mode. To disable this feature, use the no form of this command

withdraw { disable}

no withdraw { disable }

Syntax Description


disable	Disables MAC address withdrawal.

Command Default

By default, MAC address withdrawal is enabled.

Command Modes

L2VPN bridge group bridge domain MAC configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to enable disable MAC withdrawal:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# mac
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac)# withdraw disable

The following example shows how to disable sending MAC withdrawal messages to access pseudowires:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group 1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bar
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# mac
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd-mac)# withdraw access-pw disable

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.
bridge group (VPLS)	Creates a bridge group so that it can contain bridge domains and then to assign network interfaces to the bridge domain.
l2vpn	Enters L2VPN configuration mode.
mac (VPLS)	Enters L2VPN bridge group bridge domain MAC configuration mode.

Bias-Free Language

Results

Chapter: Virtual Private LAN Services Commands

Virtual Private LAN Services Commands

action (VPLS)

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

aging (VPLS)

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

bridge-domain (VPLS)

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

bridge group (VPLS)

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

clear l2vpn bridge-domain (VPLS)

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

flooding disable

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

interface (VPLS)

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

learning disable (VPLS)

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

limit (VPLS)

Syntax Description

Command Default

Command Modes