![]() Note | OCx Port License should be enabled for the configuration. |
CESoP is not supported.
Mixed mode support, for example, DS1 and E1 or DS3 and E3 or SONET and SDH simultaneously on different ports is not available.
E1/E3, Unidirectional Path Switching Ring (UPSR), and Data Communication Channel (DCC) are not supported.
Multiservice functionality: PPP, MLPPP, FR, and MLFR are not supported.
EoS and EoPDH are not supported.
The IM is only supported on Cisco RSP2 Module.
The configure replace command is not supported on the T1/E1 interface modules.
A combination of T1/T3/SONET with E1/E3/SDH modes are not supported.
The Cisco Software License Activation feature is a set of processes and components to activate Cisco IOS-XE software feature sets by obtaining and validating fee-based Cisco software licenses.You should enable the license only for OCx ports. License is not required for the ports 0-15 (DSx ports).
You should associate a required license to a port. Many licenses can be configured for a port. Only one license can be associated with a port as only one rate can be configured at a time. Other licenses are not required unless rate is changed frequently.
OC-3
OC-12
OC-48
On each IM, OCx port can be configured on ports 16-19. For example, a maximum of four OC-3 ports can be configured on ports 16-19. A maximum of four OC-12 ports can be configured on ports 16-19. A maximum of one OC-48 port can be configured on ports 16-19.
All licenses enabled on the IM ports are removed.
The free licenses can be associated with the same or different IM ports.
When IM is inserted back in the same slot, the IM ports require the licenses based on the configurations.
The available free licenses are used and old configurations are retained.
When free licenses are not available, the controller port moves to "shut" state and the following error message is displayed:
Controller port does not have license so putting it into shut state. Un-shut after enabling license or remove controller port configuration
Remove all the configurations present at rate level and beyond.
Enable the license on the port that has the same rate as that of the configured controller. For example, enable OC3 license for any OC3 configuration to remove the "shut" state.
To install or upgrade a license by using the license install command, you must have already received the license file from the Cisco Product License Registration portal at http://www.cisco.com/go/license (or you already backed up the license by using the license save command).
To install the license:
enable show license udi Convert the PAK to a license by entering the PAK and the UDI into the Cisco Product License Registration portal: http://www.cisco.com/go/license license install stored-location-url show license detail end
![]() Note | This command is not applicable for DSx ports (0-15). |
![]() Note | You should configure controller mediatype and controller SONET before enabling the license on the port. License enabling is allowed when the license with the same rate is configured on the port. The configuration fails if the license with a different rate is configured on the port. |
To enable port licensing:
enable configure terminal platform enable controller MediaType 0/4/16 oc3 controller MediaType 0/4/16 mode sonet exit controller sonet 0/4/16 rate oc3 exit
Use the show license detail command to verify the license configuration:
Router#show license detail Index: 15 Feature: oc3 Version: 1.0 License Type: Permanent License State: Active, In Use License Count: 1/1/0 (Active/In-use/Violation) License Priority: Medium Store Index: 4 Store Name: Primary License Storage #
![]() Note | Disabling a license is not successful if a rate is configured on the controller that requires the license. Hence, you should first remove the controller configuration before disabling the license. |
To disable port licensing:
enable configure terminal controller sonet 0/4/16 sts-1 1 no vtg 1 t1 1 cem-group 23 unframed no mode vt-15 controller MediaType 0/4/16 no mode sonet exit no platform enable controller MediaType 0/4/16 oc3
To uninstall a license:
enable configure terminal no platform enable controller MediaType slot/bay/port OC3 end license clear feature-name
To enable T1 controller:
enable configure terminal controller mediatype 0/4/0 mode t1 end
To configure T1 interface, use the following commands:
enable configure terminal controller mediatype 0/4/0 mode t1 exit controller t1 0/4/0 clock source internal framing esf cablelength short 110 linecode b8zs no shutdown exit
To enable T3 controller:
enable configure terminal controller mediatype 0/4/12 mode t3 end
To enable SONET controller:
enable configure terminal controller mediatype 0/0/16 mode sonet end
The following table shows the commands for the IM configuration:
Command |
Link |
---|---|
platform enable controller Mediatype <slot/bay/port> <port rate> |
Related Topic |
Document Title |
---|---|
Cisco IOS commands |
|
Compact-SFP |
Cisco SFP Modules for Gigabit Ethernet Applications Data Sheet |
Standard/RFC |
Title |
---|---|
— |
There are no standards and RFCs for this feature. |
MIB |
MIBs Link |
---|---|
— |
There are no MIBs for this feature. |
Description |
Link |
---|---|
The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies. To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds. Access to most tools on the Cisco Support website requires a Cisco.com user ID and password. |