Table Of Contents
Installing the CE-MR-6 Card in the Cisco ONS 15310-MA
Obtaining Optical Networking Information
Where to Find Safety and Warning Information
Cisco Optical Networking Product Documentation CD-ROM
Obtaining Documentation, Obtaining Support, and Security Guidelines
Installing the CE-MR-6 Card in the Cisco ONS 15310-MA
March 2008Product Name: 15310-CE-MR-6=
This document provides a card description, specifications, and installation procedure for the CE-MR-6 card. The CE-MR-6 card is compatible with Cisco ONS 15310-MA (ANSI) shelf assembly. Use this document in conjunction with the Cisco ONS 15310 Procedure Guide when working with CE-MR-6 cards.
This document contains the following sections:
•
Obtaining Optical Networking Information
•
Obtaining Documentation, Obtaining Support, and Security Guidelines
CE-MR-6 Card Description
The CE-MR-6 card is a 5 Gbps data module for use in the Cisco ONS 15310-MA. It provides support for L1 packet mapping functions (Ethernet to SONET). The 10/100/1000 Mbps Ethernet encapsulated traffic is mapped into SONET circuits. Each circuit has three main attributes:
•
Low order, or high order
•
Contiguous concatenation (CCAT) or virtual concatenation (VCAT)
•
Generic framing procedure (GFP), LEX, high-level data link control (HDLC) or PPP (point-to-point protocol) based framing.
•
CE-MR-6 cards support LCAS that allows hitless dynamic adjustment of SONET link bandwidth.
The CE-MR-6 is a Layer 1 (Ethernet Private Line) and Layer 1+ (Virtual Private Wire Services) mapper card with six IEEE 802 compliant 10/100/1000 Mbps Ethernet ports that provide 1:1 mapping of Ethernet ports to circuits. It maps each port to a unique SONET circuit in a point-to-point configuration.
The CE-MR-6 card allows you to provision and manage an Ethernet private line service like a traditional SONET line. CE-MR-6 card applications include providing carrier-grade Ethernet private line services and high-availability transport.
The CE-MR-6 card carries any Layer 3 protocol that can be encapsulated and transported over Ethernet, such as IP or IPX. The Ethernet frame from the data network is transmitted on the Ethernet cable into the 10/100/1000 Mbps Ethernet ports on a CE-MR-6 card. The CE-MR-6 card transparently maps Ethernet frames into the SONET payload using packet-over-SONET/SDH (POS) encapsulation. The POS circuit, with its encapsulated Ethernet inside, is then multiplexed onto an optical card like any other SONET synchronous transport signal (STS). When the payload reaches the destination node, the process is reversed and the data is transmitted from the 10/100/1000 Mbps Ethernet ports in the destination CE-MR-6 card onto the Ethernet cable and data network.
The CE-MR-6 card supports ITU-T G.707-based standards. It allows a soft reset, which is errorless in most cases. During the soft reset if there is a provisioning change, or if the firmware is replaced during a software upgrade process, the reset is equivalent to a hard reset. For more information on a soft reset of a CE-MR-6 card using CTC, refer to the Cisco ONS 15310 Procedure Guide.
The CE-MR-6 card supports the following copper and fiber Small Form-Factor Pluggables (SFPs):
•
ONS-SI-GE-SX
•
ONS-SI-GE-LX
•
ONS-SI-GE-ZX
•
ONS-SI-100-FX
•
ONS-SI-100-LX10
•
ONS-SE-100-BX10U
•
ONS-SE-100-BX10D
•
ONS-SE-ZE-EL
![]()
Note
Due to mechanical constraints related to the dimensions of the pluggable device, two ONS-SE-ZE-EL copper SFPs cannot be inserted in the same SFP double cage receptacle. They can only be inserted into slots 1 or 2, 3 or 4, and 5 or 6. Upto three ONS-SE-ZE-EL copper SFPs can be inserted in one CE-MR-6 card
Faceplate
Figure 1 shows the CE-MR-6 card front panel.
Figure 1 CE-MR-6 Front Panel
![]()
CE-MR-6 Card Level Indicators
Table 1 shows the card-level LEDs on the CE-MR-6 card.
CE-MR-6 Port Level Indicators
Table 2 shows the port-level LEDs on the CE-MR-6 card.
CE-MR-6 Card Specifications
The CE-MR-6 card has the following specifications:
•
Environmental
–
Operating temperature
I-Temp: -40 to +65 degrees Celsius (-40 to 149 degrees Fahrenheit)
–
Operating humidity: 5 to 95%, noncondensing
–
Power consumption: 63.00 W, 1.32 A at -48 V, 214.96 BTU/hr
•
Dimensions
–
Height: 176.28 mm (6.94 in.)
–
Width: 34.29 mm (1.35 in.)
–
Depth: 236.68 mm (9.318 in.)
–
Weight (not including clam shell): 0.499 kg (1.1 lb)
Installing the CE-MR-6 Card
![]()
Warning
Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029
![]()
Warning
To comply with the Telcordia GR-1089 Network Equipment Building Systems (NEBS) standard for electromagnetic compatibility and safety, connect the copper Ethernet ports to intrabuilding or nonexposed wiring and cabling only.
![]()
CautionDo not install the CE-MR-6 card in an ONS 15310-MA if the ambient temperature exceeds 131 degrees F (55 degrees C).
![]()
CautionAlways use the supplied ESD wristband when working with a powered ONS 15310-MA. Plug the wristband cable into either of the ESD jacks, on the far left and right faceplates in the shelf.
![]()
Note
If protective clips are installed on the backplane connectors of the cards, remove the clips before installing the cards.
Step 1
Install the CE-MR-6 card in a traffic card slot:
a.
Open the card ejector.
b.
Use the ejector at the top of the card and firmly slide the card along the guide rails until the card plugs into the receptacle at the back of the slot.
c.
Verify that the card is inserted correctly and close the ejector on the card.
![]()
Note
The CE-MR-6 card is hot-pluggable, so it can be inserted or removed without turning off the power to the ONS 15310-MA.
Step 2
Verify the CE-MR-6 card LED activity:
a.
Verify that the red FAIL LED is off.
b.
Verify that the green ACT LED is on.
Step 3
When you log into CTC, verify that the card appears properly in CTC node view.
Stop. You have completed this procedure.
Related Documentation
•
Cisco ONS 15310-CL and Cisco ONS 15310-MA Procedure Guide
•
Cisco ONS 15310-CL and Cisco ONS 15310-MA Reference Manual
•
Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide
Obtaining Optical Networking Information
This section contains information that is specific to optical networking products. For information that pertains to all of Cisco, refer to the Obtaining Documentation, Obtaining Support, and Security Guidelines section.
Where to Find Safety and Warning Information
For safety and warning information, refer to the Cisco Optical Transport Products Safety and Compliance Information document that accompanied the product. This publication describes the international agency compliance and safety information for the Cisco ONS 15310-MA system. It also includes translations of the safety warnings that appear in the ONS 15310-MA system documentation.
Cisco Optical Networking Product Documentation CD-ROM
Optical networking-related documentation, including Cisco ONS 15xxx product documentation, is available in a CD-ROM package that ships with your product. The Optical Networking Product Documentation CD-ROM is updated periodically and may be more current than printed documentation.
Obtaining Documentation, Obtaining Support, and Security Guidelines
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.
This document is to be used in conjunction with the documents listed in the "Related Documentation" section.
CCDE, CCENT, CCSI, Cisco Eos, Cisco Explorer, Cisco HealthPresence, Cisco IronPort, the Cisco logo, Cisco Nurse Connect, Cisco Pulse, Cisco SensorBase, Cisco StackPower, Cisco StadiumVision, Cisco TelePresence, Cisco TrustSec, Cisco Unified Computing System, Cisco WebEx, DCE, Flip Channels, Flip for Good, Flip Mino, Flipshare (Design), Flip Ultra, Flip Video, Flip Video (Design), Instant Broadband, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn, Cisco Capital, Cisco Capital (Design), Cisco:Financed (Stylized), Cisco Store, Flip Gift Card, and One Million Acts of Green are service marks; and Access Registrar, Aironet, AllTouch, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Lumin, Cisco Nexus, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, Continuum, EtherFast, EtherSwitch, Event Center, Explorer, Follow Me Browsing, GainMaker, iLYNX, IOS, iPhone, IronPort, the IronPort logo, Laser Link, LightStream, Linksys, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, PCNow, PIX, PowerKEY, PowerPanels, PowerTV, PowerTV (Design), PowerVu, Prisma, ProConnect, ROSA, SenderBase, SMARTnet, Spectrum Expert, StackWise, WebEx, and the WebEx logo are registered trademarks of Cisco and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1002R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
© 2008 Cisco Systems, Inc. All rights reserved.