June 2010
|
- Updated the Tools/Equipment
information for EAP cable length in “NTP-G301 Connect the ONS 15454 Multishelf
Node and Subtending Shelves to an MS-ISC-100T Card” in chapter, “Install the
Cisco ONS 15454 Shelf”.
- Updated the list of supplied
materials in chapters, “Install the Cisco ONS 15454 M2 Shelf” and “Install the
Cisco ONS 15454 M6 Shelf”.
- Updated the AC fuse rating
values for the ONS 15454 M2 and ONS 15454 M6 shelf assemblies in chapters,
“Install the Cisco ONS 15454 M2 Shelf” and “Install the Cisco ONS 15454 M6
Shelf”.
- Added a table, “Port
Mapping” in the chapter, “Install the Cisco ONS 15454 Shelf”.
- Added a note to explain the
configuration of 48-port Catalyst switch in chapters, “Install the Cisco ONS
15454 Shelf” and “Install the Cisco ONS 15454 M6 Shelf”.
- Added a note on temporary door in
chapter, “Install the Cisco ONS 15454 M6 Shelf”.
|
August 2010
|
- Updated
the wall mounting procedure for ONS 15454 M2 shelf in chapter, “Install the
Cisco ONS 15454 M2 Shelf”.
- Added a
note in NTP-G253 in the chapter, “Install the Cisco ONS 15454 M6 Shelf”.
- Updated
the total maximum power consumption of ONS 15454 M6 shelf in appendix “Hardware
Specifications”.
|
September
2010
|
- Modified
procedure, “DLP-G682 Connect the ONS 15454 M6 as the Node Controller in a Mixed
Multishelf Configuration” in chapter, “Install the Cisco ONS 15454 M6 Shelf”.
|
October
2010
|
- Added a
note in the chapter “Installing the ONS 15454 (ANSI and ETSI) Shelf”.
- Added
two notes and a step in “DLP-G18 Connect Office Power to the ONS 15454 ANSI” of
the chapter, “Installing the ONS 15454 (ANSI and ETSI) Shelf”.
- Updated
step 1 in “DLP-G19 Turn On and Verify Office Power” of the chapter, “Installing
the ONS 15454 (ANSI and ETSI) Shelf”.
- Added a
step in the “Connect Office Power (DC) to the ONS 15454 M2 Shelf” and “Connect
Office Power (DC) to the ONS 15454 M6 Shelf” procedures of the chapters,
“Install the Cisco ONS 15454 M2 Shelf” and Install the Cisco ONS 15454 M6
Shelf” respectively.
- Added a
note in the “Connect Office Power (AC) to the ONS 15454 M2 Shelf” and “Connect
Office Power (AC) to the ONS 15454 M6 Shelf” procedures of the chapters,
“Install the Cisco ONS 15454 M2 Shelf” and Install the Cisco ONS 15454 M6
Shelf” respectively.
|
November
2010
|
- Added
Step 11 and a note to Step 9 in the procedure, “DLP-G18 Connect Office Power to
the ONS 15454 ANSI”.
- Updated
Step 1 in the procedure “DLP-G19 Turn On and Verify Office Power”.
- Updated
Step 11 in the procedure, “DLP-G572 Connect Office Power (DC) to the ONS 15454
M6 Shelf (ANSI Only)” of the chapter, “Install the Cisco ONS 15454 M6 Shelf”.
|
February
2011
|
- Added
the section “Card Slot Requirements” in the chapter “Preparing to Install the
ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf”.
|
May 2011
|
- Updated
the sections “NTP-G252 Install the ONS 15454 M6 Shelf” and “NTP-G253 Install
the External Connection Unit (ECU)” in the chapter “Install the Cisco ONS 15454
M6 Shelf”.
- Changed
the breaker rating (fuse) for the ONS 15454 ETSI chassis from 40A to 30A in the
chapter, “Installing the ONS 15454 (ANSI and ETSI) Shelf”.
- Added a
note in the “Fiber module” section in chapter “Install the Cisco ONS 15454 M6
Shelf”.
- Added a
note in the procedure, “NTP-Attach Wires to Timing, LAN, and Craft Pin
Connections in ONS 15454 M2” of chapter, “Install the Cisco ONS 15454 M2
Shelf”.
|
June 2011
|
- Added
the length of the SCSI cables in the chapter “Install the Cisco ONS 15454 M6
Shelf”.
- Updated
the procedure “DLP-G655 Lock Cables for a Clean Routing” to “DLP-G655 Route and
Lock Cables” in chapter “Install the Cisco ONS 15454 M6 Shelf”.
- Added a
note in the procedure “NTP-Attach Wires to Timing, LAN, and Craft Pin
Connections in ONS 15454 M2” in chapter, “Install the Cisco ONS 15454 M2
Shelf”.
|
August 2011
|
- Added
additional information in the “External LAN Interface for EMS” section in
appendix, “Hardware Specifications”.
- Updated
the values for total maximum power consumption (ONS 15454 M6) in the section
“System Power” of the appendix, “Hardware Specifications”.
- Updated
the “Alarm Connectors” section in the chapter “Install the Cisco ONS 15454 M6
Shelf”.
|
September
2011
|
- Updated
the “ONS 15454 M6 Shelf Specifications” section in the appendix “Hardware
Specifications”.
|
November
2011
|
Updated the
alarm details in the chapter, “Installing the Cisco 15454 M6 Shelf”.
|
February
2012
|
Added a
table that lists alarm connector pin details for SCSI alarm wire wrap cable in
the chapter, “Installing the Cisco 15454 M6 Shelf”.
|
March 2012
|
- Updated
the size of the power cable for ONS 15454 M2 and ONS 15454 M6 shelves in the
chapter, “Preparing to Install”.
- Updated
the note in the chapter, “Installing the ONS 15454 (ANSI and ETSI) Shelf”.
- Updated
the “Fan Tray Units for ONS 15454 Cards” table in the chapter, “Installing the
ONS 15454 (ANSI and ETSI) Shelf”.
|
May 2012
|
- Updated
the note in the section “Fan Tray Units for ONS 15454 Cards” in the chapter
“Installing the ONS 15454 (ANSI and ETSI) Shelf”.
- Updated
the section “Fan-Tray Assembly” and the procedure “NTP-G268 Install the
Fan-Tray Assembly in the ONS 15454 M2 Shelf” in the chapter “Installing the ONS
15454 M2 Shelf”.
- Updated
the section “Fan-Tray Assembly” and the procedure “NTP-G257 Install the
Fan-Tray Assembly in the ONS 15454 M6 Shelf” in the chapter “Installing the ONS
15454 M6 Shelf”.
- Updated
the table “Fan-Tray Assembly Power Requirements” and the section “System Power”
in the appendix “Hardware Specifications”.
- Added
the procedure “DLP-G729 Connect the ONS 15454 M6 as the Node Controller in a
Mixed Multishelf Configuration without a Catalyst Switch” in the chapter,
“Installing the ONS 15454 M6 Shelf”.
|
June 2012
|
- Updated
the section “Multishelf Management” in the chapter “Installing the ONS 15454 M6
Shelf”.
- Updated
the sections “NTP-G308 Connect the ONS 15454 M6 Multishelf Node and the ONS
15454 M6 Subtending Shelves” and “NTP-G310 Upgrade the ONS 15454 Multishelf
Configuration using the ONS 15454 M6” in the chapter “Installing the ONS 15454
M6 Shelf”.
|
July 2012
|
- Added
a section “Cooling Profile” in the chapter “Installing the ONS 15454 M6 Shelf”.
-
Updated the section “Multishelf LAN Topologies” in the chapter “Installing the
ONS 15454 M6 Shelf”.
|
August
2012
|
Updated
the table “Multishelf LAN Topologies in Cisco ONS 15454 M6 and Cisco ONS 15454”
in the chapter “Installing the ONS 15454 M6 Shelf”.
|
October
2012
|
Updated
the table “Multishelf LAN Topologies in Cisco ONS 15454 M6 and Cisco ONS 15454”
in the chapter “Installing the ONS 15454 M6 Shelf”.
|
November
2012
|
-
Updated the section “Mounting Multiple Nodes” in the chapter “Installing the
ONS 15454 M6 Shelf” and “Mounting a Single Node” in the chapter “Installing the
ONS 15454 M2 Shelf”.
- In the
chapter “Maintaining the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454
M6 Shelf”, updated the procedures:
-
NTP-G114 Inspect and Replace the Air Filter
-
NTP-G274 Replace the Air Filter of the ONS 15454 M2 Shelf Assembly
-
NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf Assembly
-
NTP-G263 Replace the Air Filter of the AC Power Module in the ONS 15454 M6
Shelf Assembly
|
February
2013
|
-
Deleted the section “NTP-G300 Configure a Cisco Catalyst 2950 or Catalyst 3560
(Extended) for a Multishelf Node” and updated the following sections in the
chapter “Installing the ONS 15454 (ANSI and ETSI) Shelf”:
-
NTP-G295 Connect the ONS 15454 Multishelf Node and Subtending Shelves to a
Catalyst 2950 or Catalyst 3560
-
NTP-G296 Upgrade the ONS 15454 Multishelf with MS-ISC Card Configuration Using
the Catalyst 3560
-
NTP-G297 Upgrade the ONS 15454 Multishelf with Catalyst 2950 Configuration
Using the Catalyst 3560
-
NTP-G298 Configure a Cisco Catalyst 2950 or Catalyst 3560 (Active and Standby)
for a ONS 15454 Multishelf Node
-
Updated the table “Multishelf LAN Topologies in Cisco ONS 15454 M6 and Cisco
ONS 15454” and the following sections in the chapter “Installing the ONS 15454
M6 Shelf”:
-
NTP-G309 Connect the ONS 15454 M6 and the ONS 15454 in a Mixed Multishelf
Configuration
-
DLP-G682 Connect the ONS 15454M6 as the Node Controller in a Mixed Multishelf
Configuration Using the Catalyst 3560
-
DLP-G683 Connect the ONS 15454 as the Node Controller in a Mixed Multishelf
Configuration
-
NTP-G310 Upgrade the ONS 15454 Multishelf Configuration Using the ONS 15454 M6
-
DLP-G687 Upgrade the ONS 15454 Multishelf with the Catalyst 2950 Switch
Configuration
-
DLP-G688 Upgrade the ONS 15454 Multishelf with MS-ISC Card Configuration
-
NTP-G264 Perform the ONS 15454 M6 Shelf Installation Acceptance Test
-
Updated the figures “Mixed Multishelf Configuration with the ONS 15454 M6 as
the Node Controller” and “Mixed Multishelf Configuration with the ONS 15454 as
the Node Controller” in the chapter “Installing the ONS 15454 M6 Shelf”.
|
March
2013
|
-
Revised the part number and included Release 9.6.0.3 features such as power
calculation for 15454-M6-DC20 power module.
-
Updated the section “External Connection Units” in the chapter “Installing the
ONS 15454 M6 Shelf” to include the 15454-M6-ECU-60 unit.
-
Updated the procedure “NTP-G329 Remove the Deep Door of the ONS 15454 M6 Shelf”
in the chapter “Installing the ONS 15454 M6 Shelf”.
-
Updated the procedure “NTP-G331 Remove the Deep Door of the ONS 15454 M2 Shelf”
in the chapter “Installing the ONS 15454 M2 Shelf”.
- Added
a note in the chapters, “Installing the ONS 15454 M2 Shelf” and “Installing the
ONS 15454 M6 Shelf”.
-
Updated the section “Power Modules” in the chapter “Installing the ONS 15454 M2
Shelf”.
-
Updated the section “Passive Unit Inventory Interfaces” in the chapter
“Installing the ONS 15454 M6 Shelf”.
|
July 2013
|
-
Revised the part number and included Release 9.8 features such as AC2 power
module.
|
November
2013
|
- Added
Release 10.0 feature on deep-front panel. Updated section “4.1 Front Door”.
-
NTP-G343 Install the Air Plenum in ONS 15454 M2 Shelf.
-
DLP-G763 Install Air Plenum for ONS 15454 M2 Shelf in ANSI 19-inch
Configuration.
-
DLP-G764 Install Air Plenum in ONS 15454 M2 Shelf for ANSI 23-inch
Configuration.
-
DLP-G765 Install Air Plenum for ONS 15454 M2 Shelf in ETSI Configuration.
- Added
Release 10.0 feature on air plenum to orient the air flow within the chassis in
section “5.4 Air Plenum“.
-
NTP-G344 Install the Air Plenum in ONS 15454 M6 Shelf
-
DLP-G766 Install Air Plenum for ONS 15454 M6 Shelf in ANSI 19-inch Cabinet.
-
DLP-G767 Install Air Plenum in ONS 15454 M6 Shelf for ANSI 23-inch
Configuration.
-
DLP-G768 Install Pre-assembled Air Plenums in ANSI 23-inch Configuration.
-
DLP-G769 Install Air Plenum for ONS 15454 M6 Shelf in ETSI Configuration.
|
April
2014
|
- The
full length book-PDF was generated.
|
December
2014
|
- Added
information for the 15454-M6-DC40 power module.
|
June 2015
|
- Added
a note to the section, “Alarm Connectors” in the chapter “Installing the ONS
15454 M6 Shelf”.
|
January
2016
|
|
April
2016
|
Added the
following note:
Due to
memory limitations, TCC2/TCC2P cards are not supported as the node controller
in multi-shelf configuration from R10.5.2.6. Hence, it is recommended to use
TCC3 card as the node controller in multi-shelf configuration. However, the
TCC2/TCC2P cards can be used as a subtended controller and also in a
stand-alone configuration.
|
June 2016
|
Updated
the bandwidth specifications for ONS 15454 M6 in the appendix, “Hardware
Specifications”.
|
July 2016
|
Updated
the sections, “Filler and Blank Cards” in the chapters, “Installing the ONS
15454 M12 (ANSI and ETSI) Shelf”, “Installing the ONS 15454 M2 Shelf”, and
“Installing the ONS 15454 M6 Shelf”.
|
November
2016
|
Included
R 10.6.1 features.
|
March 2017
|
Added a
note to "DLP-G298 Install LAN Wires in ONS 15454 M6" in the chapter,
"Installing the ONS 15454 M6 Shelf".
|
April 2017
|
Updated for R10.6.2
|