EID–1050
|
Connection failed on node {0}.
|
This
error message is displayed when the nodes are disconnected in Layer2+ >
Topology > Trace L2 Topology.
|
EID–3246
|
To proceed, select the required number of nodes.
|
This
error message is displayed when you click
Finish without selecting the required number of
nodes in the Select Nodes for the VPLS Network screen.
|
EID–4039
|
Could
not retrieve load balancing information.
|
This
error message is displayed when you receive an error in the Load Balancing
subtab of Channel Groups tab in Packet Transport System View.
|
EID–4046
|
Service ID syntax error: {0}.
|
This
error message is displayed when you specify an invalid service ID format during
Ethernet Virtual Circuit (EVC) query.
|
EID–5130
|
Connection failed on node {0}.
|
Refer to
the error message text.
|
EID–5148
|
Unable
to set the SRLG for Router {0}.
|
This
error message is displayed when you are unable to set the Shared Risk Link
Group (SRLG) for the specified router.
|
EID–5190
|
Unable
to trace Layer 2 topology. The root link may have been deleted.
|
This
error message is displayed when the Layer 2 topology view is refreshed.
|
WID–5191
|
All the
EFP configurations will be lost. Are you sure you want to continue?
|
This warning message is displayed when you click the Reset
button in the EFP configuration dialog box. All the saved Ethernet Flow Point
(EFP) configurations will be cleared.
|
WID–5192
|
The
Label Data has changed. Please use Apply to save.
|
This warning message is displayed when you edit the
Multiprotocol Label Switching – Transport Profile (MPLS–TP) labels and click
Finish before saving them.
|
WID–5193
|
The
Labels on the route could not be computed.
|
This warning message is displayed when CTC cannot compute the
labels during MPLS–TP tunnel creation or LSP addition.
|
EID–5194
|
The MAC
Address mentioned is invalid.
|
Refer to the error message text.
|
EID–5195
|
The
Static MAC Address provisioning on EFP failed.
|
This error message is displayed when an error occurs while
configuring a static MAC address on EFP.
|
WID–5196
|
You have
not selected any nodes for discovery query. This may result in slow performance
to discover the services of interest from the entire network. Do you wish to
proceed?
|
This
warning message is displayed when you have not selected any nodes during the
Layer 2 services query. The query is issued to the entire network that slows
down the discovery process.
|
EID–5197
|
The specified IP address is invalid.
|
This
error message is displayed during an explicit path creation when the IP address
specified for the unmanaged node is invalid.
|
EID–5198
|
An interface has to be selected.
|
This
error message is displayed during an explicit path creation when you do not
specify the interface for each managed node.
|
EID–5199
|
TPE nodes cannot be used as SPE.
|
This
error message is displayed during pseudowire creation. The Terminating Provider
Edge (TPE) nodes that are used as source and destination nodes cannot be used
as Switch Provider Edge (SPE) nodes.
|
EID–5200
|
A valid router ID must be selected.
|
This error message is displayed when you do not specify a valid
router ID during Multiprotocol Label Switching – Traffic Engineering (MPLS-TE)
tunnel creation or pseudowire creation.
|
EID–5201
|
A valid
route cannot be found for the circuit creation request. Do you want to continue
anyway?
|
This
error message is displayed during pseudowire creation. This error message is
displayed when there are no MPLS-TE or MPLS-TP tunnels that can be used by the
pseudowire.
|
EID–5202
|
Sanity
Check Failed on the LSP being added.
|
This
error message is displayed when the labels modified by the user are incorrect.
|
EID–5203
|
EFP Configuration Error : {0}.
|
This
error message is displayed when you try to save an invalid EFP configuration in
the EFP configuration dialog box during EVC or pseudowire provisioning.
|
EID–5204
|
The
Static MAC Address retrieval on EFP failed.
|
This
error message is displayed when the EFP fails to retrieve the static MAC
address.
|
EID–5205
|
Unable
to clear the proactive protection on the router.
|
This
error message is displayed during proactive protection clearing operation on
Cisco ASR 9000 Series Router or Carrier Routing System.
|
WID–5206
|
Unable
to clear proactive protection on the router. Do it manually.
|
This
warning message is displayed during proactive protection clearing operation on
Cisco ASR 9000 Series Router or Carrier Routing System.
|
EID–5207
|
Specified Multicast IP Address does not fall within the valid
range.
|
Refer to the error message text.
|
EID-5228
|
Deleting an LSP might impact the tunnel status
|
This
error message is displayed when you try to delete an LSP. The following message
is displayed in the warning dialog box:
Deleting
an LSP might impact the tunnel status. Do you want to delete the selected LSP?
|
WID–6506
|
Deleting
the loopback interface the MPLS functionalities will be affected. Do you want
to continue?
|
This
warning message is displayed when you try to delete the loopback address.
|
WID–5239
|
It is
not recommended to do any service provisioning on a dual-homed ring via PRC
when the WRC is down. It may get lost when the WRC becomes active again. Do you
wish to proceed?
|
This
warning message is displayed when you try to provision any service on a CPT 50
in a ring through the PRC, when the WRC is down.
|
WID–5240
|
One or
more selected services exist on a dual-homed ring where the WRC is down. It is
not recommended to do any service provisioning on a dual-homed ring via PRC
when the WRC is down. It may get lost when the WRC becomes active again. Do you
wish to proceed?
|
This
warning message is displayed when you try to provision the service that exist
on a dual-homed ring through the PRC, when the WRC is down.
|
EID–6519
|
Only
show commands are admitted.
|
This
error message is displayed when you enter non-show commands.
|
EID–6520
|
BFD
Template Name cannot be null.
|
This error message is displayed when you try to create a
Bidirectional Fault Detection (BFD) template without entering the template
name.
|
EID–6521
|
BFD
Template Multiplier cannot be null.
|
This
error message is displayed when you try to create a BFD template without
entering a value for the multiplier. The multiplier value specifies the number
of consecutive BFD control packets that can be missed before BFD declares a
peer as unavailable.
|
EID–6522
|
BFD
Template Tx/Rx Interval cannot be null.
|
This error message is displayed when you try to create a BFD
template without entering the values for the transmit and receive intervals.
|
EID–6523
|
Link
Number cannot be null.
|
This
error message is displayed when you try to configure a link without specifying
the link number.
|
EID–6524
|
Port
cannot be null.
|
This
error message is displayed when the port is not selected under the Service
Level Alarm tab in Packet Transport System View.
|
EID–6525
|
IP
Address is invalid.
|
This
error message is displayed when the next hop address specified during the link
number configuration is invalid.
|
EID–6526
|
Static
OAM Class name cannot be null.
|
This
error message is displayed when you try to create a static OAM class without
entering the class name.
|
EID–6527
|
Static
OAM Timer values cannot be null.
|
This
error message is displayed when you try to create a static OAM class without
specifying how often the static OAM packets must be sent out.
|
EID–6528
|
MPLS Label Range cannot be null.
|
This
error message is displayed when you do not specify a value for the minimum and
maximum MPLS label range. The minimum and maximum label values specified apply
to MPLS-TP tunnels and static pseudowires.
|
EID–6529
|
MPLS
Label Range must be from [16 - 8000].
|
This error message is displayed when you specify an MPLS label
value that is outside the valid label range.
|
EID–6530
|
Fault
OAM Refresh Timer cannot be null.
|
This
error message is displayed when you try to configure the global settings for
the MPLS-TP without specifying the value in the Refresh Timer field. The
refresh timer field specifies how often the static OAM packets must be sent
out.
|
EID–6531
|
Fault
OAM Refresh Timer value must be between 1 and 255.
|
This error message is displayed when you try to configure the
global settings for the MPLS-TP without specifying the valid values in the
Refresh Timer field.
|
EID–6532
|
Node value specified is not valid.
|
Refer to the error message text.
|
EID–6533
|
BFD
Interval range must be between 4 and 999 milliseconds.
|
This error message is displayed when you try to create a BFD
template without entering valid values (in milliseconds) for the transmit and
receive intervals.
|
EID–6534
|
BFD
Interval range must be between 3300 and 999000 microseconds.
|
This error message is displayed when you try to create a BFD
template without entering valid values (in microseconds) for the transmit and
receive intervals.
|
EID–6535
|
BFD
Template Multiplier must be between 3 and 50.
|
This
error message is displayed when you try to create a BFD template without
entering valid values for the multiplier. The multiplier value specifies the
number of consecutive BFD control packets that can be missed before BFD
declares a peer as unavailable.
To enter
value for BFD Template Multiplier follow the path: PTS view > Provisioning
tab > MPLS TP > BFD Template.
Note
| From
Release 9.5.x BFD template multiplier must be between 2 and 50.
|
|
EID–6536
|
The
TE/TP Tunnel Number must be between 1 and 65535.
|
This
error message is displayed when you try to create a MPLS-TE or MPLS-TP tunnel
without specifying the valid values for the tunnel number.
|
EID–6537
|
Pseudowire Class name cannot be null.
|
This
error message is displayed when you try to create a pseudowire class without
entering the class name.
|
EID–6538
|
Protocol should be None for TP Tunnel in the preferred path.
|
Refer to the error message text.
|
EID–6540
|
Either of Static OAM class and BFDoVCCV with status signalling
can be used for signalling with static Tunnels.
|
Refer to the error message text.
|
EID–6541
|
BFDoVCCV
cannot be used for status signalling with LDP based Tunnels.
|
Refer to the error message text.
|
EID–6542
|
Static
OAM class cannot be used for signalling with LDP based Tunnels.
|
Refer to the error message text.
|
EID–6543
|
Syslog is not Enabled.
|
Refer to the error message text.
|
EID–6547
|
Valid
License is not available on this card.
|
This
error message is displayed during port creation when all the available licenses
have been used.
|
EID–6548
|
License Operation Error.
|
This
error message is displayed when you receive an unexpected error during the
license operation. Some of the error situations are as follows:
-
Better license exists.
-
Duplicate license.
-
License is already revoked.
-
Precedence of the selected license line is in incorrect state.
-
Unique Device Identifier (UDI) in the license line does not
match with the local UDI.
|
EID–6550
|
The
Product ID of the card does not support Licensing.
|
Refer to the error message text.
|
EID–6551
|
The card
is not in provisioned state, hence this license data cannot be fetched
currently.
|
This
error message is displayed when the license data cannot be retrieved because
the card is not provisioned.
|
EID–6552
|
License
operation failed due to Communication failure with the line card.
|
Refer to the error message text.
|
EID–6553
|
Please
select/enter valid values for InterfaceType/InterfaceNumber.
|
Refer to the error message text.
|
EID–6554
|
The MAC Address mentioned is invalid.
|
Refer to the error message text.
|
EID–6555
|
The
minimum value of the range for H/W protected tunnels must be from 1-4095.
|
Refer to the error message text.
|
EID–6556
|
The
maximum number of H/W protected tunnels is 1024.
|
Refer to the error message text.
|
EID–6558
|
Service Alarm cannot be null.
|
This
error message is displayed when a service alarm is not selected before querying
the service-level alarms.
|
EID–6559
|
Service Type cannot be null.
|
This
error message is displayed when a service type is not selected before querying
the service-level alarms.
|
EID–6560
|
Service ID cannot be null.
|
This
error message is displayed when a service ID is not selected before querying
the service-level alarms.
|
EID–6561
|
Selected router is not {0}.
|
This
error message is displayed when a Cisco ASR 9000 Series Router or Carrier
Routing System is not selected during control channel creation.
|
EID–6562
|
License
file size has exceeded the limit.
|
This
error message is displayed when the license file is larger than the maximum
supported size.
|
WID–6563
|
Removing
the {0} might be traffic affecting. Do you want to continue?
|
This
warning message is displayed when you try to delete targeted LDP sessions.
|
EID–6565
|
Cannot retrieve the MAC table from the node as either or both
uplinks are not present or are in invalid state.
|
Refer to the error message text.
|
EID–6566
|
BFDoVCCV
requires Control Word to be Enabled.
|
This
error message is displayed when creating a pseudowire class. This error message
is displayed when you enable BFD Control Channel over Virtual Circuit
Connection Verification (VCCV) without enabling the control word.
|
EID–6567
|
Min Label cannot be more than Maximum Label.
|
Refer to the error message text.
|
EID–6568
|
Local label is in use.
|
This
error message is displayed when the specified local label is already being used
by an MPLS-TE or MPLS-TP tunnel. Use the other unused label.
|
EID–6569
|
Local label is out of range.
|
This
error message is displayed when the specified local label is outside the MPLS
static label range.
|
EID–6570
|
VC ID is in use.
|
This
error message is displayed when the specified Virtual Circuit (VC) ID during
pseudowire creation is already in use.
|
EID–6571
|
Either
Next Hop or Unicast Tx-Mac required for Non-P2P (shared) Interface.
|
This
error message is displayed when you try to configure a link without specifying
the next hop IP address or MAC address.
|
EID–6399
|
The MIP Provisioning Failed.
|
Refer to the error message text.
|
EID–6401
|
The
Provisioning Failed. An MIP or MEP is configured on the interface.
|
This error message is displayed when you try to delete the
maintenance association (MA) profile that is associated with a Maintenance
Intermediate Point (MIP) or Maintenance End Point (MEP).
|
EID–6620
|
The {0}
field cannot exceed {1} characters.
|
This
error message is displayed when the length of the maintenance domain name or
maintenance association profile name exceeds the threshold value.
|
EID–6624
|
The
start interval cannot exceed hold interval and hold interval cannot exceed
maximum interval.
|
This
error message is displayed when the start interval and hold interval values in
Link-state Advertisement (LSA) and Shortest Path First (SPF) areas exceed the
hold interval and maximum interval values respectively.
|
EID–5220
|
MA
Profile name should not exceed 50 characters.
|
This
error message is displayed when the length of MA profile name exceeds 50
characters.
|
EID–5222
|
An error
occurred while deleting the NEIGHBOR.
|
This error message is displayed when you try to delete a
neighbor pseudowire for a given node in the Edit > End Point Pseudowire tab
of the Virtual Private LAN Service (VPLS) circuit.
|
EID–5223
|
The last
NEIGHBOR cannot be deleted.
|
This
error message is displayed when you try to delete the last neighbor pseudowire
for a given node in the Edit > End Point Pseudowire tab of the VPLS circuit.
|
EID–6599
|
The
selected bandwidth is not available.
|
This
error message is displayed when the bandwidth of the pseudowire exceeds the
available bandwidth on the MPLS–TE or MPLS–TP tunnel.
|
EID–6621
|
MP-ID cannot be Empty.
|
This
error message is displayed when a value to query for Connectivity Fault
Management (CFM) based on Maintenance Point Identifier (MP ID) is not entered
in the MP ID field of the Maintenance > Service Statistics tab.
|
EID–6622
|
VC-ID cannot be Empty.
|
This
error message is displayed when a value to query for MPLS statistics is not
entered in the VC ID field of the Maintenance > Service Statistics tab.
|
EID–6623
|
Service Name cannot be Empty.
|
This
error message is displayed when a value to query for CFM based on the domain
name and service name is not entered in the Service Name field of the
Maintenance > Service Statistics tab.
|
EID–2016
|
Circuit deletion failed.
|
This
error message is displayed when you try to delete a VPLS circuit that has some
EFPs associated.
|
EID–6610
|
The MPID
Number must be between 1 and 8191.
|
This
error message is displayed when an incorrect value is entered in the MP ID
field of the Maintenance > OAM tab during the ping operation for an EVC
service.
|
EID–6611
|
The COS
Number must be between 0 and 7.
|
This
error message is displayed when an incorrect value is entered in the COS field
of the Maintenance > OAM tab during the ping operation for an EVC service.
|
EID–6612
|
The
Source Number must be between 1 and 8191.
|
This
error message is displayed when an incorrect value is entered in the Source
field of Maintenance > OAM tab during the ping operation for an EVC service.
|
EID–6617
|
Discard
Class value should be between 0 to 2.
|
This
error message is displayed when an incorrect value is entered in the Discard
Class field of Provisioning > QoS > Table Map > Create Table Map.
|
EID–6618
|
Qos
Group value should be between 0 to 7.
|
This
error message is displayed when an incorrect value is entered in the QoS Group
field of Provisioning > QoS > Table Map > Create Table Map.
|
EID–6613
|
Qos
Group value should be less than 8.
|
This
error message is displayed when an incorrect value is entered in the QoS Group
field of Provisioning > QoS > Table Map > Create Table Map.
|
EID-6626
|
FOG deletion failed
|
This
error message is displayed when an attempt to delete a Fan-Out Group (FOG) has
failed.
|
EID-6627
|
No {0} was configured
|
This error message is displayed when a port span is created with
an incorrect span source, EFP span source, or a span destination. The {0} in
the error message is a:
-
Source, if a port span is created without configuring a span
source.
- EFP Source, if an EFP span
is created without configuring any EFP source.
-
Destination, if a span is created without configuring any span
destination.
To enter
a value for span source, EFP source, and destination follow the path: PTS
view> Provisioning> Span> Create
|
EID-6628
|
The Service ID field cannot be empty
|
This
error message is displayed when there is no value entered in the service ID
field.
|
EID-6629
|
The {0} interface is in use.\n
|
This
error message is displayed when a attempt is made to reuse an already in-use
interface.
|
EID-6630
|
Ip SLA ID must be in the range 1-2147483647
|
This
error message is displayed when the Ip SLA ID value entered is outside the
defined range.
To enter
a value in the Ip SLA ID field follow the path: PTS view > DM Config>
Provisioning tab > Y1731 tab > Delay Measurement tab > Configuration
tab.
|
EID-6631
|
Domain name cannot be empty
|
This
error message is displayed when no domain name is specified.
To enter
a value in the domain name field, follow the path: PTS view > DM Config>
Provisioning tab > Y1731 tab > Delay Measurement tab > Configuration
tab
|
EID-6632
|
Age out must be in the range 1-2073600
|
This
error message is displayed when the Ageout value entered is outside the defined
range.
To enter
a value in the Ageout field, follow the path: PTS view > DM Config >
Provisioning tab > Y1731 tab > Delay Measurement tab > Schedule tab
with Ageout value beyond the range 1-2073600.
|
EID-6633
|
Life value must be entered
|
This
error message is displayed when there is no value entered in the Life field.
To enter
a value in the Life field, follow the path: PTS view > DM Config >
Provisioning tab > Y1731 tab > Delay Measurement tab > Schedule tab
with no value in the Life field.
|
EID-6634
|
Frame size must be in the range 64-384
|
This
error message is displayed when the frame size value you have entered is
outside the defined range.
To enter
a value in the Frame size field, follow the path: PTS view > DM Config>
Provisioning tab > Y1731 tab > Delay Measurement tab > Configuration
tab.
|
EID-6635
|
Frame interval must be 100 msec or 1 sec
|
This
error message is displayed when an invalid frame interval value is entered.
To enter
a value in the Frame interval field, follow the path: PTS view > DM
Config> Provisioning tab > Y1731 tab > Delay Measurement tab >
Configuration tab.
|
EID-6636
|
Aggregate interval must be in the range 1-65535
|
This
error message is displayed when the aggregate interval value entered is outside
the defined range.
To enter
a value in the Aggregate Interval Value field, follow the path: PTS view >
DM Config> Provisioning tab > Y1731 tab > Delay Measurement tab >
Configuration tab.
|
EID-6637
|
Maximum delay must be in the range 1-65535
|
This
error message is displayed when the maximum delay value entered is outside the
defined range.
To enter
a value in the Maximum Delay value field, follow the path: PTS view > DM
Config> Provisioning tab > Y1731 tab > Delay Measurement tab >
Configuration tab.
|
EID-6642
|
CFM Disabled on Interface
|
This
error message is displayed when CFM is disabled on the interface. To enable
CFM, click Provisioning > CFM > Global Settings > Ethernet Interfaces
> Enable CFM
|
EID-6644
|
No Such Service
|
This
error message is displayed when CTC queries for a service, that does not exist.
|
EID-6645
|
Enter proper Service ID
|
This
error message is displayed when a invalid value is entered in the Service ID
field.
To enter
the Service ID, follow the path: PTS view> provisioning > Y1731 >
Configuration tab.
|
EID-6646
|
Fog Name length should be less than 255 characters
|
This
error message is displayed when the name length of the Fan-Out group exceed the
defined characters limit.
|
EID-6648
|
The minimum threshold cannot be empty
|
This
error message is displayed when the value in the Reaction Type field is
specified as Immediate and no value is entered in the Falling Threshold field.
To
configure the Reaction type and Falling Threshold fields, follow the path: PTS
view > DM Config > Provisioning tab > Y1731 tab > Delay Measurement
tab > Configuration tab.
|
EID-6649
|
The maximum threshold cannot be empty
|
This
error message is displayed when the value in the Reaction Type field is
specified as Immediate and no value is entered in the Rising Threshold field.
To
configure the Reaction Type and Rising Threshold fields, follow the path: PTS
view > DM Config > Provisioning tab > Y1731 tab > Delay Measurement
tab > Configuration tab.
|
EID-6653
|
Minimum threshold value must be in the range 1-60000
|
This
error message is displayed when the value in the Reaction Type field is
specified as Immediate and the value specified in the Falling Threshold field
is outside the defined range that is, 1-60000.
To
configure the Reaction type and Falling Threshold fields, follow the path: PTS
view > DM Config Provisioning tab > Y1731 tab > Delay Measurement tab
> Configuration tab.
|
EID-6654
|
Maximum threshold value must be in the range 1-60000
|
This
error message is displayed when the value in the Reaction type field is
specified as Immediate and value specified in the Rising Threshold field is
outside the defined range that is, 1-60000.
To
configure the Reaction type and Rising Threshold fields, follow the path: PTS
view > DM Config> Provisioning tab > Y1731 tab > Delay Measurement
tab > Configuration tab.
|
EID-6677
|
Services exist on this port. Therefore, delete all services
from this port before configuring TDM
|
This
error message is displayed when the E1-CES or E3-CES pluggable is configured on
the port where the services, which are not compatible with E1-CES or E3-CES
pluggable, already exist.
|
EID-6678
|
Invalid Ring device identifier
|
This
error message is displayed when the identifier entered in the Device Identifier
field contains more than 50 characters, any special character, or only
numerals.
|
EID-6679
|
East port cannot be same as west port in a Ring
|
This
error message is displayed when you select the east port same as the west port
while creating a ring with the topology type as Ring.
|
EID-6680
|
Invalid CPT 50 device identifier
|
This
error message is displayed when the device identifier of CPT 50 entered in the
Device Identifier field of the CPT 50 Attribute dialog contains more than 50
characters, any special characters, or only numerals.
|
EID-6681
|
Invalid CPT 50 location
|
This
error message is displayed when the location of CPT 50 entered in the Location
field of the CPT 50 Attribute dialog contains more than 50 characters.
|
EID-6682
|
Ring deletion failed
|
This
error message is displayed when you delete the ring on which a CPT 50 is
already configured.
|
EID-6683
|
CPT 50 with the same device identifier already exists
|
This
error message is displayed when you assign the name and location to a new CPT
50, same as the previously added CPT 50.
|
EID-6684
|
PWE with dynamic tunnel is not supported over TDM interface
|
This
error message is displayed when pseudowire is created over the E1-CES or E3-CES
interface and associated pseudowire class has TE as the tunnel type.
|
EID-6685
|
PWE with BFDoVCC is not supported over TDM interface
|
This
error message is displayed when pseudowire is created over the E1-CES or E3-CES
interface and associated pseudowire class is BFDoVCC enabled.
|
EID-6686
|
PWE with dynamic protocol is not supported over TDM interface
|
This
error message is displayed when pseudowire is created over the E1-CES or E3-CES
interface and the associated pseudowire class has LDP protocol.
|
EID-6687
|
PWE with OAM class is not supported over TDM interface
|
This
error message is displayed when pseudowire is created over the E1-CES or E3-CES
interfaceE1-CES or E3-CES pluggable and the associated pseudowire class is OAM
enabled .
|
EID-6688
|
PWE with packet sequencing is not supported over TDM interface
|
This
error message is displayed when pseudowire is created over the E1-CES or E3-CES
interface and the associated pseudowire class is sequencing enabled.
|
EID-6690
|
Port is already in use. Delete the ring to configure the OTN on
this port
|
This
error message is displayed when you enable OTN on the port where ring is
already created.
|
EID-6691
|
Port is already in use. Disable the OTN to create a ring on
this port
|
This
error message is displayed when you create a ring on the port where OTN is
enabled.
|
EID-6695
|
Maximum number of CPT 50s allowed in a ring, is 20
|
This
error message is displayed when you add more than 20 CPT 50s, in a ring.
|
EID-6733
|
The corresponding CPT 50 box is not connected physically.
Connect the CPT 50 with the given ID to open its PTS view.
|
This
error message is displayed when you add more than 20 CPT 50s, in a ring.
|
EID-6729
|
Peer IP should not be same as Node IP
|
This
error message is displayed when you entered the peer node IP same as the WRC
IP.
|
EID-6730
|
A single home ring exists, so node role cannot be changed
|
This
error message is displayed when a ring is already created on the node.
|
EID-6731
|
A Dual home ring exists, so node role cannot be changed
|
This
error message is displayed when you modify the node role of a node where a
dual-homed ring is already configured.
|
EID-6737
|
Inter link port already exists
|
This
error message is displayed when you configure a new interconnect (IC) link on
the node where an IC link is already configured.
|
EID-6738
|
Inter link port exists on ring ports
|
This
error message is displayed when you configure a dual-homed ring on the node
where an IC link is already configured.
|
EID-6739
|
An IC link is configured so Node Role and Peer IP can not be
changed
|
This
error message is displayed when you modify either the node role or the peer IP
address of a node where a dual-homed ring is already configured.
|
EID-6677
|
Services exist on this port. Therefore, delete all services
from this port before configuring TDM
|
This
error message is displayed when the TDM pluggable is configured on the port
where the services, which are not compatible with TDM, already exist.
|
EID-6684
|
PWE with dynamic tunnel is not supported over TDM interface
|
This
error message is displayed when pseudowire is created over the TDM interface
and associated pseudowire class has TE as the tunnel type.
|
EID-6685
|
PWE with BFDoVCC is not supported over TDM interface
|
This
error message is displayed when pseudowire is created over the TDM interface
and associated pseudowire class is BFDoVCC enabled.
|
EID-6686
|
PWE with dynamic protocol is not supported over TDM interface
|
This
error message is displayed when pseudowire is created over the TDM interface
and the associated pseudowire class has LDP protocol.
|
EID-6687
|
PWE with OAM class is not supported over TDM interface
|
This
error message is displayed when pseudowire is created over the TDM interface
and the associated pseudowire class is OAM enabled.
|
EID-6688
|
PWE with packet sequencing is not supported over TDM interface
|
This
error message is displayed when pseudowire is created over the TDM interface
and the associated pseudowire class is sequencing enabled.
|
WID-5238
|
For node on which Vty option is enabled, Manually logout or kill
the sessions
|
This
error message is displayed when the Vty option is enabled and at the time of
deleting the user, Logout before delete option is checked.
|
WID–6748
|
It is not recommended to do any
provisioning on a dual-homed ring via PRC when the WRC is down. It would be
lost when the WRC becomes active again. Do you wish to proceed?
|
This warning message is displayed when you try to provision
any CPT 50 in a dual-homed ring through the PRC, when the WRC is down.
|