EID–1050
|
Connection failed on node {0}.
|
This
error message is displayed when the nodes are disconnected in Layer2+ >
Topology > Trace L2 Topology.
|
EID–3246
|
The wizard was not able to validate the data.
|
Refer to
the error message text.
|
EID–4039
|
The MA
profile does not exist.
|
Refer to
the error message text.
|
EID–4046
|
Service ID syntax error: {0}.
|
This
error message is displayed when you specify an invalid service ID format during
Ethernet Virtual Circuit (EVC) query.
|
EID–5130
|
Connection failed on node {0}.
|
Refer to
the error message text.
|
EID–5148
|
Unable
to set the SRLG for Router {0}.
|
This
error message is displayed when you are unable to set the Shared Risk Link
Group (SRLG) for the specified router.
|
EID–5190
|
Unable
to trace Layer 2 topology. The root link may have been deleted.
|
This
error message is displayed when the Layer 2 topology view is refreshed.
|
WID–5191
|
All the
EFP configurations will be lost. Are you sure you want to continue?
|
This warning message is displayed when you click the Reset
button in the EFP configuration dialog box. All the saved Ethernet Flow Point
(EFP) configurations will be cleared.
|
WID–5192
|
The
Label Data has changed. Please use Apply to save.
|
This warning message is displayed when you edit the
Multiprotocol Label Switching – Transport Profile (MPLS–TP) labels and click
Finish before saving them.
|
WID–5193
|
The
Labels on the route could not be computed.
|
This warning message is displayed when CTC cannot compute the
labels during MPLS–TP tunnel creation or LSP addition.
|
EID–5194
|
The MAC
Address mentioned is invalid.
|
Refer to the error message text.
|
EID–5195
|
The
Static MAC Address provisioning on EFP failed.
|
This error message is displayed when an error occurs while
configuring a static MAC address on EFP.
|
WID–5196
|
You have
not selected any nodes for discovery query. This may result in slow performance
to discover the services of interest from the entire network. Do you wish to
proceed?
|
This
warning message is displayed when you have not selected any nodes during the
Layer 2 services query. The query is issued to the entire network that slows
down the discovery process.
|
EID–5197
|
The specified IP address is invalid.
|
This
error message is displayed during an explicit path creation when the IP address
specified for the unmanaged node is invalid.
|
EID–5198
|
An interface has to be selected.
|
This
error message is displayed during an explicit path creation when you do not
specify the interface for each managed node.
|
EID–5199
|
TPE nodes cannot be used as SPE.
|
This
error message is displayed during pseudowire creation. The Terminating Provider
Edge (TPE) nodes that are used as source and destination nodes cannot be used
as Switch Provider Edge (SPE) nodes.
|
EID–5200
|
A valid router ID must be selected.
|
This error message is displayed when you do not specify a valid
router ID during Multiprotocol Label Switching – Traffic Engineering (MPLS-TE)
tunnel creation or pseudowire creation.
|
EID–5201
|
A valid
route cannot be found for the circuit creation request. Do you want to continue
anyway?
|
This
error message is displayed during pseudowire creation. This error message is
displayed when there are no MPLS-TE or MPLS-TP tunnels that can be used by the
pseudowire.
|
EID–5202
|
Sanity
Check Failed on the LSP being added.
|
This
error message is displayed when the labels modified by the user are incorrect.
|
EID–5203
|
EFP Configuration Error : {0}.
|
This
error message is displayed when the outer VLAN Tag and the inner VLAN Tag tries
to use same list/range simultaneously.
|
EID–5204
|
The
Static MAC Address retrieval on EFP failed.
|
This
error message is displayed when the EFP fails to retrieve the static MAC
address.
|
EID–5205
|
Unable
to clear the proactive protection on the router.
|
This
error message is displayed during proactive protection clearing operation on
Cisco ASR 9000 Series Router or Carrier Routing System.
|
WID–5206
|
Unable
to clear proactive protection on the router. Do it manually.
|
This
warning message is displayed during proactive protection clearing operation on
Cisco ASR 9000 Series Router or Carrier Routing System.
|
EID–5207
|
Specified Multicast IP Address does not fall within the valid
range.
|
Refer to the error message text.
|
EID-5228
|
Deleting an LSP might impact the tunnel status
|
This
error message is displayed when you try to delete an LSP. The following message
is displayed in the warning dialog box:
Deleting
an LSP might impact the tunnel status. Do you want to delete the selected LSP?
|
WID–6506
|
Deleting
the loopback interface the MPLS functionalities will be affected. Do you want
to continue?
|
This
warning message is displayed when you try to delete the loopback address.
|
WID–5239
|
It is
not recommended to do any service provisioning on a dual-homed ring via PRC
when the WRC is down. It may get lost when the WRC becomes active again. Do you
wish to proceed?
|
This
warning message is displayed when you try to provision any service on a CPT 50
in a ring through the PRC, when the WRC is down.
|
WID–5240
|
One or
more selected services exist on a dual-homed ring where the WRC is down. It is
not recommended to do any service provisioning on a dual-homed ring via PRC
when the WRC is down. It may get lost when the WRC becomes active again. Do you
wish to proceed?
|
This
warning message is displayed when you try to provision the service that exist
on a dual-homed ring through the PRC, when the WRC is down.
|
EID–6519
|
Only
show commands are admitted.
|
This
error message is displayed when you enter non-show commands.
|
EID–6520
|
BFD
Template Name cannot be null.
|
This error message is displayed when you try to create a
Bidirectional Fault Detection (BFD) template without entering the template
name.
|
EID–6521
|
BFD
Template Multiplier cannot be null.
|
This
error message is displayed when you try to create a BFD template without
entering a value for the multiplier. The multiplier value specifies the number
of consecutive BFD control packets that can be missed before BFD declares a
peer as unavailable.
|
EID–6522
|
BFD
Template Tx/Rx Interval cannot be null.
|
This error message is displayed when you try to create a BFD
template without entering the values for the transmit and receive intervals.
|
EID–6523
|
Link
Number cannot be null.
|
This
error message is displayed when you try to configure a link without specifying
the link number.
|
EID–6524
|
Port
cannot be null.
|
This
error message is displayed when the port is not selected under the Service
Level Alarm tab in Packet Transport System View.
|
EID–6525
|
IP
Address is invalid.
|
This
error message is displayed when the next hop address specified during the link
number configuration is invalid.
|
EID–6526
|
Static
OAM Class name cannot be null.
|
This
error message is displayed when you try to create a static OAM class without
entering the class name.
|
EID–6527
|
Static
OAM Timer values cannot be null.
|
This
error message is displayed when you try to create a static OAM class without
specifying how often the static OAM packets must be sent out.
|
EID–6528
|
MPLS Label Range cannot be null.
|
This
error message is displayed when you do not specify a value for the minimum and
maximum MPLS label range. The minimum and maximum label values specified apply
to MPLS-TP tunnels and static pseudowires.
|
EID–6529
|
MPLS
Label Range must be from [16 - 8000].
|
This error message is displayed when you specify an MPLS label
value that is outside the valid label range.
|
EID–6530
|
Fault
OAM Refresh Timer cannot be null.
|
This
error message is displayed when you try to configure the global settings for
the MPLS-TP without specifying the value in the Refresh Timer field. The
refresh timer field specifies how often the static OAM packets must be sent
out.
|
EID–6531
|
Fault
OAM Refresh Timer value must be between 1 and 255.
|
This error message is displayed when you try to configure the
global settings for the MPLS-TP without specifying the valid values in the
Refresh Timer field.
|
EID–6532
|
Node value specified is not valid.
|
Refer to the error message text.
|
EID–6533
|
BFD
Interval range must be between 4 and 999 milliseconds.
|
This error message is displayed when you try to create a BFD
template without entering valid values (in milliseconds) for the transmit and
receive intervals.
|
EID–6534
|
BFD
Interval range must be between 3300 and 999000 microseconds.
|
This error message is displayed when you try to create a BFD
template without entering valid values (in microseconds) for the transmit and
receive intervals.
|
EID–6535
|
BFD
Template Multiplier must be between 3 and 50.
|
This
error message is displayed when you try to create a BFD template without
entering valid values for the multiplier. The multiplier value specifies the
number of consecutive BFD control packets that can be missed before BFD
declares a peer as unavailable.
To enter
value for BFD Template Multiplier follow the path: PTS view > Provisioning
tab > MPLS TP > BFD Template.
Note
| From
Release 9.5.x BFD template multiplier must be between 2 and 50.
|
|
EID–6536
|
The
TE/TP Tunnel Number must be between 0 and 999.
|
This
error message is displayed when you try to create a MPLS-TE or MPLS-TP tunnel
without specifying the valid values for the tunnel number.
|
EID–6537
|
Pseudowire Class name cannot be null.
|
This
error message is displayed when you try to create a pseudowire class without
entering the class name.
|
EID–6538
|
Protocol should be None for TP Tunnel in the preferred path.
|
Refer to the error message text.
|
EID–6540
|
Either of Static OAM class and BFDoVCCV with status signalling
can be used for signalling with static Tunnels.
|
Refer to the error message text.
|
EID–6541
|
BFDoVCCV
cannot be used for status signalling with LDP based Tunnels.
|
Refer to the error message text.
|
EID–6542
|
Static
OAM class cannot be used for signalling with LDP based Tunnels.
|
Refer to the error message text.
|
EID–6543
|
Syslog is not Enabled.
|
Refer to the error message text.
|
EID–6547
|
Valid
License is not available on this card.
|
This
error message is displayed during port creation when all the available licenses
have been used.
|
EID–6548
|
License Operation Error.
|
This
error message is displayed when you receive an unexpected error during the
license operation. Some of the error situations are as follows:
-
Better license exists.
-
Duplicate license.
-
License is already revoked.
-
Precedence of the selected license line is in incorrect state.
-
Unique Device Identifier (UDI) in the license line does not
match with the local UDI.
|
EID–6550
|
The
Product ID of the card does not support Licensing.
|
Refer to the error message text.
|
EID–6551
|
The card
is not in provisioned state, hence this license data cannot be fetched
currently.
|
This
error message is displayed when the license data cannot be retrieved because
the card is not provisioned.
|
EID–6552
|
License
operation failed due to Communication failure with the line card.
|
Refer to the error message text.
|
EID–6553
|
Please
select/enter valid values for InterfaceType/InterfaceNumber.
|
Refer to the error message text.
|
EID–6554
|
The MAC Address mentioned is invalid.
|
Refer to the error message text.
|
EID–6555
|
The
minimum value of the range for H/W protected tunnels must be from 1-4095.
|
Refer to the error message text.
|
EID–6556
|
The
maximum number of H/W protected tunnels is 1024.
|
Refer to the error message text.
|
EID–6558
|
Service Alarm cannot be null.
|
This
error message is displayed when a service alarm is not selected before querying
the service-level alarms.
|
EID–6559
|
Service Type cannot be null.
|
This
error message is displayed when a service type is not selected before querying
the service-level alarms.
|
EID–6560
|
Service ID cannot be null.
|
This
error message is displayed when a service ID is not selected before querying
the service-level alarms.
|
EID–6561
|
Selected router is not {0}.
|
This
error message is displayed when a Cisco ASR 9000 Series Router or Carrier
Routing System is not selected during control channel creation.
|
EID–6562
|
License
file size has exceeded the limit.
|
This
error message is displayed when the license file is larger than the maximum
supported size.
|
WID–6563
|
Removing
the {0} might be traffic affecting. Do you want to continue?
|
This
warning message is displayed when you try to delete targeted LDP sessions.
|
EID–6565
|
Cannot retrieve the MAC table from the node as either or both
uplinks are not present or are in invalid state.
|
Refer to the error message text.
|
EID–6566
|
BFDoVCCV
requires Control Word to be Enabled.
|
This
error message is displayed when creating a pseudowire class. This error message
is displayed when you enable BFD Control Channel over Virtual Circuit
Connection Verification (VCCV) without enabling the control word.
|
EID–6567
|
Min Label cannot be more than Maximum Label.
|
Refer to the error message text.
|
EID–6568
|
Local label is in use.
|
This
error message is displayed when the specified local label is already being used
by an MPLS-TE or MPLS-TP tunnel. Use the other unused label.
|
EID–6569
|
Local label is out of range.
|
This
error message is displayed when the specified local label is outside the MPLS
static label range.
|
EID–6570
|
VC ID is in use.
|
This
error message is displayed when the specified Virtual Circuit (VC) ID during
pseudowire creation is already in use.
|
EID–6571
|
Either
Next Hop or Unicast Tx-Mac required for Non-P2P (shared) Interface.
|
This
error message is displayed when you try to configure a link without specifying
the next hop IP address or MAC address.
|
EID–6399
|
The MIP Provisioning Failed.
|
Refer to the error message text.
|
EID–6401
|
The
Provisioning Failed. An MIP or MEP is configured on the interface.
|
This error message is displayed when you try to delete the
maintenance association (MA) profile that is associated with a Maintenance
Intermediate Point (MIP) or Maintenance End Point (MEP).
|
EID–6620
|
The {0}
field cannot exceed {1} characters.
|
This
error message is displayed when the length of the maintenance domain name or
maintenance association profile name exceeds the threshold value.
|
EID–6624
|
The
start interval cannot exceed hold interval and hold interval cannot exceed
maximum interval.
|
This
error message is displayed when the start interval and hold interval values in
Link-state Advertisement (LSA) and Shortest Path First (SPF) areas exceed the
hold interval and maximum interval values respectively.
|
EID–5220
|
MA
Profile name should not exceed 50 characters.
|
This
error message is displayed when the length of MA profile name exceeds 50
characters.
|
EID–5222
|
An error
occurred while deleting the NEIGHBOR.
|
This error message is displayed when you try to delete a
neighbor pseudowire for a given node in the Edit > End Point Pseudowire tab
of the Virtual Private LAN Service (VPLS) circuit.
|
EID–5223
|
The last
NEIGHBOR cannot be deleted.
|
This
error message is displayed when you try to delete the last neighbor pseudowire
for a given node in the Edit > End Point Pseudowire tab of the VPLS circuit.
|
EID–6599
|
The
selected bandwidth is not available.
|
This
error message is displayed when the bandwidth of the pseudowire exceeds the
available bandwidth on the MPLS–TE or MPLS–TP tunnel.
|
EID–6621
|
MP-ID cannot be Empty.
|
This
error message is displayed when a value to query for Connectivity Fault
Management (CFM) based on Maintenance Point Identifier (MP ID) is not entered
in the MP ID field of the Maintenance > Service Statistics tab.
|
EID–6622
|
VC-ID cannot be Empty.
|
This
error message is displayed when a value to query for MPLS statistics is not
entered in the VC ID field of the Maintenance > Service Statistics tab.
|
EID–6623
|
Service Name cannot be Empty.
|
This
error message is displayed when a value to query for CFM based on the domain
name and service name is not entered in the Service Name field of the
Maintenance > Service Statistics tab.
|
EID–2016
|
Circuit deletion failed.
|
This
error message is displayed when you try to delete a VPLS circuit that has some
EFPs associated.
|
EID–6610
|
The MPID
Number must be between 1 and 8191.
|
This
error message is displayed when an incorrect value is entered in the MP ID
field of the Maintenance > OAM tab during the ping operation for an EVC
service.
|
EID–6611
|
The COS
Number must be between 0 and 7.
|
This
error message is displayed when an incorrect value is entered in the COS field
of the Maintenance > OAM tab during the ping operation for an EVC service.
|
EID–6612
|
The
Source Number must be between 1 and 8191.
|
This
error message is displayed when an incorrect value is entered in the Source
field of Maintenance > OAM tab during the ping operation for an EVC service.
|
EID–6617
|
Discard
Class value should be between 0 to 2.
|
This
error message is displayed when an incorrect value is entered in the Discard
Class field of Provisioning > QoS > Table Map > Create Table Map.
|
EID–6618
|
Qos
Group value should be between 0 to 7.
|
This
error message is displayed when an incorrect value is entered in the QoS Group
field of Provisioning > QoS > Table Map > Create Table Map.
|
EID–6613
|
Qos
Group value should be less than 8.
|
This
error message is displayed when an incorrect value is entered in the QoS Group
field of Provisioning > QoS > Table Map > Create Table Map.
|
EID-6626
|
FOG deletion failed
|
This
error message is displayed when an attempt to delete a Fan-Out Group (FOG) has
failed.
|
EID-6627
|
No {0} was configured
|
This error message is displayed when a port span is created with
an incorrect span source, EFP span source, or a span destination. The {0} in
the error message is a:
-
Source, if a port span is created without configuring a span
source.
- EFP Source, if an EFP span
is created without configuring any EFP source.
-
Destination, if a span is created without configuring any span
destination.
To enter
a value for span source, EFP source, and destination follow the path: PTS
view> Provisioning> Span> Create
|
EID-6628
|
The Service ID field cannot be empty
|
This
error message is displayed when there is no value entered in the service ID
field.
|
EID-6629
|
The {0} interface is in use.\n
|
This
error message is displayed when a attempt is made to reuse an already in-use
interface.
|
EID-6630
|
Ip SLA ID must be in the range 1-2147483647
|
This
error message is displayed when the Ip SLA ID value entered is outside the
defined range.
To enter
a value in the Ip SLA ID field follow the path: PTS view > DM Config>
Provisioning tab > Y1731 tab > Delay Measurement tab > Configuration
tab.
|
EID-6631
|
Domain name cannot be empty
|
This
error message is displayed when no domain name is specified.
To enter
a value in the domain name field, follow the path: PTS view > DM Config>
Provisioning tab > Y1731 tab > Delay Measurement tab > Configuration
tab
|
EID-6632
|
Age out must be in the range 1-2073600
|
This
error message is displayed when the Ageout value entered is outside the defined
range.
To enter
a value in the Ageout field, follow the path: PTS view > DM Config >
Provisioning tab > Y1731 tab > Delay Measurement tab > Schedule tab
with Ageout value beyond the range 1-2073600.
|
EID-6633
|
Life value must be entered
|
This
error message is displayed when there is no value entered in the Life field.
To enter
a value in the Life field, follow the path: PTS view > DM Config >
Provisioning tab > Y1731 tab > Delay Measurement tab > Schedule tab
with no value in the Life field.
|
EID-6634
|
Frame size must be in the range 64-384
|
This
error message is displayed when the frame size value you have entered is
outside the defined range.
To enter
a value in the Frame size field, follow the path: PTS view > DM Config>
Provisioning tab > Y1731 tab > Delay Measurement tab > Configuration
tab.
|
EID-6635
|
Frame interval must be 100 msec or 1 sec
|
This
error message is displayed when an invalid frame interval value is entered.
To enter
a value in the Frame interval field, follow the path: PTS view > DM
Config> Provisioning tab > Y1731 tab > Delay Measurement tab >
Configuration tab.
|
EID-6636
|
Aggregate interval must be in the range 1-65535
|
This
error message is displayed when the aggregate interval value entered is outside
the defined range.
To enter
a value in the Aggregate Interval Value field, follow the path: PTS view >
DM Config> Provisioning tab > Y1731 tab > Delay Measurement tab >
Configuration tab.
|
EID-6637
|
Maximum delay must be in the range 1-65535
|
This
error message is displayed when the maximum delay value entered is outside the
defined range.
To enter
a value in the Maximum Delay value field, follow the path: PTS view > DM
Config> Provisioning tab > Y1731 tab > Delay Measurement tab >
Configuration tab.
|
EID-6642
|
CFM Disabled on Interface
|
This
error message is displayed when CFM is disabled on the interface. To enable
CFM, click Provisioning > CFM > Global Settings > Ethernet Interfaces
> Enable CFM
|
EID-6644
|
No Such Service
|
This
error message is displayed when CTC queries for a service, that does not exist.
|
EID-6645
|
Enter proper Service ID
|
This
error message is displayed when a invalid value is entered in the Service ID
field.
To enter
the Service ID, follow the path: PTS view> provisioning > Y1731 >
Configuration tab.
|
EID-6646
|
Fog Name length should be less than 255 characters
|
This
error message is displayed when the name length of the Fan-Out group exceed the
defined characters limit.
|
EID-6648
|
The minimum threshold cannot be empty
|
This
error message is displayed when the value in the Reaction Type field is
specified as Immediate and no value is entered in the Falling Threshold field.
To
configure the Reaction type and Falling Threshold fields, follow the path: PTS
view > DM Config > Provisioning tab > Y1731 tab > Delay Measurement
tab > Configuration tab.
|
EID-6649
|
The maximum threshold cannot be empty
|
This
error message is displayed when the value in the Reaction Type field is
specified as Immediate and no value is entered in the Rising Threshold field.
To
configure the Reaction Type and Rising Threshold fields, follow the path: PTS
view > DM Config > Provisioning tab > Y1731 tab > Delay Measurement
tab > Configuration tab.
|
EID-6653
|
Minimum threshold value must be in the range 1-60000
|
This
error message is displayed when the value in the Reaction Type field is
specified as Immediate and the value specified in the Falling Threshold field
is outside the defined range that is, 1-60000.
To
configure the Reaction type and Falling Threshold fields, follow the path: PTS
view > DM Config Provisioning tab > Y1731 tab > Delay Measurement tab
> Configuration tab.
|
EID-6654
|
Maximum threshold value must be in the range 1-60000
|
This
error message is displayed when the value in the Reaction type field is
specified as Immediate and value specified in the Rising Threshold field is
outside the defined range that is, 1-60000.
To
configure the Reaction type and Rising Threshold fields, follow the path: PTS
view > DM Config> Provisioning tab > Y1731 tab > Delay Measurement
tab > Configuration tab.
|
EID-2099
|
An error occurred while ring switching
|
Refer to the error message text.
|
EID-2113
|
The extension byte for the ring cannot be
set
|
Refer to the error message text.
|
EID-2116
|
The extension byte setting for the ring is
invalid
|
Refer to the error message text.
|
EID-2118
|
The ring cannot be deleted. A protection
operation is set. All protection operations must be clear for ring to be
deleted.
|
Refer to the error message text.
|
EID-2121
|
The ring cannot be upgraded
|
This error message is displayed when the CPT 50 upgrade is
been initiated which are present inside a ring but failed.
|
EID-2122
|
The ring speed for is inadequate for the
upgrade procedure. Only 0 or higher 1 can be upgraded to four-fiber
|
Refer to the error message text.
|
EID-2130
|
The ring ID value is not valid. Please
enter a valid number between 0 and 9999
|
Refer to the error message text.
|
EID-2207
|
You cannot add this span. Either the ring
name is too long that is, ring name length is greater than 0 or the endpoints
do not support alphanumeric IDs.
|
Refer to the error message text.
|
EID-5244
|
It is not recommended to do any service
provisioning on a dual-homed ring via PRC when the WRC is down. It may get lost
when the WRC becomes active again. Do you wish to proceed
|
Refer to the error message text.
|
EID-5245
|
One or more selected services exist on a
dual-homed ring where the WRC is down. It is not recommended to do any service
provisioning on a dual-homed ring via PRC when the WRC is down. It may get lost
when the WRC becomes active again. Do you wish to proceed
|
Refer to the error message text.
|
EID-4055
|
Disable the service state before upgrading
the CPT50
|
This error message is displayed when the CPT 50 needs to be
upgraded but since the service state is enabled on that CPT 50, it cannot be
upgraded.
|
EID-4058
|
Invalid Device Identifier
|
This error message is displayed when the device identifier
entered is incorrect.
|
EID-4059
|
Invalid Device Description
|
This error message is displayed when the device description
entered is incorrect.
|
EID-4061
|
CPT50 with same Device Identifier already
exists
|
This error message is displayed when the device identifier
entered for a particular CPT 50 already exists.
|
EID-6693
|
CPT50 deletion failed
|
This error message is displayed when the deletion of CPT 50
is attempted but unsuccessful.
|
EID-6694
|
Maximum number of CPT50s allowed in a ring
is 0
|
Refer to the error message text.
|
EID-6696
|
The corresponding CPT 50 box is not
connected physically. Connect the CPT 50 with the given ID to open its PTS view
|
Refer to the error message text.
|
EID-6704
|
Device Identifier length cannot excced 31
characters
|
This error message is displayed when the entered device
identifier length is greater than 31 characters.
|
EID-6705
|
Device Description length cannot exceed 31
characters
|
This error message is displayed when the entered device
description length is greater than 31 characters.
|
EID-6706
|
The maximum number of CPT50s that can be
upgraded simultaneously is 10.Please select upto 10 CPT50s for upgrade
|
Refer to the error message text.
|
EID-6695
|
CPT50 deletion failed due to one of the
following reason. CPT50 is busy. Please try again later. Services are
configured on the CPT50. Delete service and then try again later
|
Refer to the error message text.
|
EID-6701
|
Ring deletion failed as CPT50 are
available in the segment
|
This error message is displayed when the deletion of a
particular ring is attempted but unsuccessful since CPT 50s are present inside
the ring.
|
EID-4062
|
Node role should be set as single home to
create single-homed rings
|
This error message is displayed when the dingle home ring
creation is initiated and the node role has not been selected as single-homed.
|
EID-6690
|
Port is already used in rings, OTN should
not be enabled
|
This error message is displayed when the specific ports are
already used in ring configuration and cannot be considered as OTN ports.
|
EID-6691
|
You cannot select XFP ports as east and
west port in a Ring
|
This error message is displayed when you select XFP ports
for creating ring.
|
EID-6692
|
REP cannot be enabled on Ring Ports
|
This error message is displayed when the user tries to
enable REP on the ring ports.
|
EID-6698
|
No actual ring exist corresponding to the
selected preprovisioned ring
|
Refer to the error message text.
|
EID-4057
|
East port cannot be same as west port in a
Ring
|
This error message is displayed when the east port is
selected same as west port or vice-versa.
|
EID-4060
|
Ring deletion failed
|
This error message is displayed when the deletion of ring
is initiated and is unsuccessful.
|
EID-6702
|
Ring deletion failed as no segment exists
with given segment id
|
This error message is displayed when the ring deletion is
initiated for a particular segment id which does not exists.
|
EID-6703
|
The Ring Name length cannot exceed 49
characters
|
This error message is displayed when the ring name entered
is exceeding 49 characters.
|
EID-4056
|
Please provide node role for WRC/PRC
|
Refer to the error message text.
|
EID-6699
|
No actual topology exists since PRC is
standby and WRC is down
|
Refer to the error message text.
|
EID-6700
|
No actual topology exists at CTC since
both WRC and PRC are down/not present in the network
|
Refer to the error message text.
|
EID-6778
|
It is not recommended to do any
provisioning on a dual-homed ring via PRC when WRC is down. It would be lost
when WRC becomes active again.Do you wish to continue
|
Refer to the error message text.
|
EID-6777
|
WRC is already Active hence switchover not
allowed
|
This error message is displayed when the switchover for a
WRC node is initiated which is already in active state.
|
EID-6687
|
CPT50 with same Device Identifier already
exists
|
This error message is displayed when the device identifier
entered for a particular CPT 50 already exist.
|
EID-6697
|
CPT50 deletion failed
|
Refer to the error message text.
|
EID-6733
|
The corresponding CPT 50 box is not
connected physically. Connect the CPT 50 with the given ID to open its PTS
view.
|
This error message is displayed when the PTS view is not
getting opened for a particular CPT 50. It is connected in a ring but it is not
physically connected to the node.
|
EID-6699
|
Services are configured/other
configurations done on CPT50
|
Refer to the error message text.
|
EID-6790
|
Dynamic services are configured within the
modified label range. Need to Reload the PTF card/CPT50
|
Refer to the error message text.
|
EID-3161
|
An error occurred while upgrading the
ring.
|
This error message is displayed when the user tries to
upgrade the already created ring but it failed in some circumstance.
|
EID-3361
|
The ring termination is in use. An error
occurred while deleting the ring termination
|
This error message is displayed when the ring deletion is
attempted for a ring which is in use.
|
EID-3362
|
An error occurred while deleting the ring
termination
|
This error message is displayed when the ring termination
deletion is attempted but failed.
|
EID-3363
|
No ring terminations were selected
|
Refer to the error message text.
|
EID-3364
|
An error occurred while creating the ring
ID
|
This error message is displayed when the ring creation is in
process but system is unable to assign the unique Ring ID for the newly created
ring from the available pool.
|
EID-6693
|
Port is already used in rings, OTN should
not be enabled
|
This error message is displayed when the specific ports are
already used in ring configuration and cannot be considered as OTN ports.
|
EID-6694
|
OTN is enabled on this port. Disable OTN
to use the port in ring creation
|
This error message is displayed when during ring creation,
OTN ports are selected for ring ports but it is not allowed. OTN needs to be
disabled on those ports for ring creation.
|
EID-6698
|
Maximum number of CPT50s allowed in a ring
is 40
|
Refer to the error message text.
|
EID-6730
|
A single home ring exists, so node role
cannot be changed
|
This error message is displayed when the node role change
is being performed but the single-homed ring is created for that node.
|
EID-6731
|
A Dual home ring exists, so node role and
Peer IP cannot be changed
|
This error message is displayed when the modification of
node role and Peer IP is performed but the Dual home ring already exist on that
node.
|
EID-6732
|
Single home node should have peer ip as
0.0.0.0
|
This error message is displayed when the Peer IP is set
different from 0.0.0.0 for single-homed ring.
|
EID-6733
|
The corresponding CPT 50 box is not
connected physically.\n Connect the CPT 50 with the given ID to open its PTS
view
|
Refer to the error message text.
|
EID-6736
|
No ring exists on this ring Id and
slot/port.
|
This error message is displayed when the ring id does not
exist in the database.
|
EID-6738
|
Inter link port exists on ring ports
|
Refer to the error message text.
|
EID-6739
|
An IClink is configured,So Node Role and
Peer IP cannot be changed
|
This error message is displayed when the editing of node
role and peer ip is attempted for the node where IClink exist.
|
EID-6788
|
IP Address cannot be assigned on the ring
core port
|
Refer to the error message text.
|
EID-6789
|
It is not recommended to change the peer
IP of the node on which the dual home ring is already created. Do you still
wish to continue
|
Refer to the error message text.
|
EID-6682
|
Invalid Ring name
|
This error message is displayed when the device identifier
entered does not match the valid criteria.
|
EID-6683
|
East port cannot be same as west port in a
Ring
|
This error message is displayed when the west port is
selected similar to the east port while dual-homed ring creation.
|
EID-6685
|
Invalid CPT50 location
|
This error message is displayed when the device location
for CPT 50 entered is incorrect.
|
EID-6686
|
Ring deletion failed
|
This error message is displayed when the attempt to delete a
ring is failed.
|
EID-6710
|
You cannot select XFP ports as east and
west port in a Ring
|
This error message is displayed when the XFP ports are
selected as east or west port during ring creation.
|
EID-6728
|
Ring cannot be deleted since the Ring
Preview/Show Actual topology window is already opened for this Ring.
|
Refer to the error message text.
|
EID-6303
|
Functional View Initialization Error.
|
This error message is displayed when the functional view of
CTC is not getting open.
|
EID-2009
|
CTC was unable to download the package.
|
This error message is displayed when the CTC is unable to
download the package due to some error.
|
EID-2023
|
CTC was unable to create a new user.
|
Refer to the error message text.
|
EID-2025
|
This feature cannot be used. Verify that each endpoint of
this circuit is running software that supports this feature.
|
Refer to the error message text.
|
EID-2029
|
The requested operation is not supported.
|
This error message is displayed whenever you try to perform
any operation which is not supported.
|
EID-2030
|
An error occurred during provisioning.
|
This error message is displayed in general whenever there
is any provisioning error and provisioning is not done.
|
EID-2033
|
An error occurred during validation.
|
This error message is displayed when the parameters entered
during provisioning are incorrect.
|
EID-2056
|
A communication error occurred.
|
This error message is displayed when some internal error
occurred during internal communication between the cards.
|
EID-2094
|
The password and confirmed password fields do not match.
|
Refer to the error message text.
|
EID-2095
|
The password is invalid.
|
Refer to the error message text.
|
EID-2126
|
An error occurred while provisioning the OSPF area.
|
Refer to the error message text.
|
EID-2186
|
The software download failed on node.
|
This error message is displayed when the user is trying to
download a new software package on the node but it failed.
|
EID-2210
|
No package name was selected.
|
Refer to the error message text.
|
EID-2211
|
No node was selected for upgrade.
|
This error message is displayed when a user clicks on the
upgrade button for PBR upgrade but no PBR is selected from the list.
|
EID-2215
|
An error occurred while leaving the page.
|
Refer to the error message text.
|
EID-2216
|
"An error occurred while entering the page.
|
Refer to the error message text.
|
EID-3041
|
An error occurred while applying the changes.
|
This error message is displayed when the provisioning
changes has not been saved after clicking the apply button due to some internal
error.
|
EID-3051
|
An error occurred while trying to save the file to your
local file system.
|
Refer to the error message text.
|
EID-3215
|
An error occurred while refreshing.
|
This error message is displayed when you click the Refresh
button but internal error occurred during refresh of the CTC pane.
|
EID-3227
|
A baseline could not be recorded. Performance metrics will
remain unchanged.
|
Refer to the error message text.
|
EID-3252
|
No download has been initiated from this CTC session.
|
This error message is displayed when you click the cancel
button in the Maintenance > Software tab and no download is in progress.
|
EID-3253
|
The reboot operation failed.
|
This error message is displayed when you try to reboot the
CPT node but the operation failed due to internal error.
|
EID-4011
|
An error occurred during provisioning.
|
This error message is displayed when there is an internal
error occurred during any provisioning on the CPT node.
|
EID-4037
|
Maximum number of MA Profiles already provisioned on the
card.
|
This error message is displayed when the maximum number of
MA profiles has already been provisioned on the card and the user is trying to
create a new one.
|
EID-4038
|
The MA Profile already exists on the card.
|
This error message is displayed when you are trying to
create a MA profile with the same name that already exist in the database.
|
EID-4040
|
The Domain Profile does not exist.
|
Refer to the error message text.
|
EID-4041
|
The Domain Profile already exists.
|
Refer to the error message text.
|
EID-4042
|
Maximum number of Domains exceeded.
|
Refer to the error message text.
|
EID-6697
|
EFP in VPLS circuit cannot be added on SPE Node.
|
Refer to the error message text.
|
EID-6699
|
No actual topology exists since PRC is standby and WRC is
down.
|
Refer to the error message text.
|
EID-6700
|
No actual topology exists at CTC since both WRC and PRC are
down/not present in the network.
|
Refer to the error message text.
|
EID-6702
|
Ring deletion failed as no segment exists with given segment
id.
|
Refer to the error message text.
|
EID-6707
|
Vlan Edit not allowed as Service has CFM configured.
|
Refer to the error message text.
|
EID-6708
|
Vlan Edit not allowed as Service has Span configured.
|
Refer to the error message text.
|
EID-6709
|
Vlan Edit not allowed as Service has Y1731 configured.
|
Refer to the error message text.
|
EID-6710
|
Vlan Edit not allowed as Service has Qos configured.
|
Refer to the error message text.
|
EID-6711
|
Vlan Edit not allowed as Service has Mac configured.
|
Refer to the error message text.
|