|
|
November 2009 |
- Added a note in “GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Ethernet Settings” table in chapter 5, “Provision Transponder and Muxponder Cards”.
- Updated the figure for fan tray assembly (ANSI) in Chapter 1, “Install the Shelf and Common Control Cards” and Chapter 13, “Maintain the Node”.
- Added a note in “Delete a PPM” procedure in the chapter, “Provision Transponder and Muxponder Cards”.
- Updated the section “DLP-G381 Provision the GE_XP and 10GE_XP Layer 2 Protection Settings” in the chapter “Provision Transponder and Muxponder Cards”.
- Added NTP-G242, DLP-354, DLP-G547, DLP-G548, DLP-G549 in the chapter, Turn Up a Node.
- Updated the procedure DLP-G381: Provision the GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Layer 2 Protection Settings in Chapter 5 “Provision Transponder and Muxponder Cards” to document Hold Off Time feature.
- Updated the procedure NTP-G119 in the chapter, Power Down a Node.
|
December 2009 |
- Updated the “ADM-10G Line SONET or SDH Tab Settings” table in the chapter, “Provision Transponder and Muxponder Cards”.
- Updated DLP-G384 in the chapter, Provision Transponder and Muxponder Cards.
- Updated DLP-G63 Install an SFP or XFP procedure in Chapter 3, “Turn Up a Node” with note on full C-band tunable XFP.
|
February 2010 |
- Added NTP-G243 and NTP-G244 in the chapter, Perform Node Acceptance Tests.
|
March 2010 |
- Updated the table GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Ethernet Settings in the chapter Provision Transponder and Muxponder Cards.
- Updated step 2c in NTP-G144 in the chapter, Turn Up a Node. Updated NTP-G159 in the chapter, Install the Shelf and Common Control Cards. Added NTP-G294 in the chapter, Install the Shelf and Common Control Cards.
|
April 2010 |
- Updated step 4 in NTP-G159 in the chapter, Install the Shelf and Common Control Cards.
- Added a note after the “GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Ethernet Settings” table and in the “Create an SVLAN Profile” procedure.
|
May 2010 |
- Added a note in the “Create 1+1 Protection for GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards” procedure in the chapter “Provision Transponder and Muxponder Cards”.
|
June 2010 |
- Updated the table with EAP cable length in NTP-G145 in the chapter, Install the Shelf and Common Control Cards.
- Updated “DLP-G450 Configuring Windows Vista to Support CTC” in the chapter, “Connect the PC and Log into the GUI”.
|
July 2010 |
- Updated “NTP-G203 Create End-to-End SVLAN Circuits” in the chapter, “Create Circuits and Provisionable Patchcords”.
- Updated “DLP-G421 Create and Store an SVLAN Database” in the chapter, “Create Circuits and Provisionable Patchcords”.
- Updated “DLP G431 View Network-Level Automatic Power Control Information” in the chapter, “Manage the Node”.
- Added “NTP-G314 Add a GE_XP or 10GE_XP Card on a FAPS Ring” in the chapter, “Provision Transponder and Muxponder Cards”.
- Added “DLP-G687 Add a GE_XP or 10GE_XP Card Facing Master Card on a FAPS Ring” in the chapter, “Provision Transponder and Muxponder Cards”.
- Added “DLP-G688 Add a GE_XP or 10GE_XP Card Between the Slave Cards on a FAPS Ring” in the chapter, “Provision Transponder and Muxponder Cards”.
- Deleted the section “DLP-G313 Verify OSC-CSM Transmit Power” in the chapter “Turn Up a Node”.
|
October 2010 |
- Updated “NTP-G152 Create and Verify Internal Patchcords” in the chapter, “Turn Up a Node”.
- Updated “NTP-G207 Create, Edit and Delete Optical Sides” in the chapter, “Turn Up a Node”.
- Added a note in the chapter, “Maintain the node”.
- Updated “DLP-G314 Verify OSCM Transmit Power” in the chapter,“Turn Up a Node”.
|
November 2010 |
- Added Step 11 and a note to Step 9 in the procedure, “DLP-G18 Connect Office Power to the ONS 15454 ANSI”.
- Updated Step 1 in the procedure “DLP-G19 Turn On and Verify Office Power”.
- Updated step 21 in “NTP-G42 Perform the Terminal Node with 32WSS and 32DMX Cards Acceptance Test”
- Updated step 22 in "NTP-G153 Perform the Terminal Node with 32WSS-L and 32DMX-L Cards Acceptance Test"
- Updated step 21 in "NTP-G167 Perform the Terminal Node with 40-WSS-C and 40-DMX-C Cards Acceptance Test"
|
March 2011 |
- Updated the description of the rxTotalPkts ethernet variable in the chapter “Provision Transponder and Muxponder Cards”.
- Added a note in the sections “Set the 40-WXC-C OCHNC Parameters”, “Perform the Native Mesh Node Acceptance Test”, and “Perform the Node Upgrade Acceptance Test”.
|
April 2011 |
- Added DLP-G689 in the chapter, Create Circuits and Provisionable Patchcords.
- Updated the section “NTP-G197 Provision the OTU2_XP Card Line Settings, PM Parameters, and Thresholds” in the chapter “Provision Transponder and Muxponder Cards”.
- Updated the purpose in "NTP-G151 Create, Delete, and Manage Optical Channel Client Connections" and added notes to "DLP-G346 Provision Optical Channel Client Connections" and "DLP-G105 Provision Optical Channel Network Connections" in the chapter, “Create Circuits and Provisionable Patchcords”.
|
May 2011 |
- Changed the breaker rating (fuse) for the ONS 15454 ETSI chassis from 40A to 30A in the chapter, “Install the Shelf and Common Control Cards”.
- Updated the note in “DLP-G266 Modify Backplane Port IP Settings in Security Mode” in the chapter, “Manage the Node” and “DLP-G56 Provision IP Settings” in the chapter, “Turn Up a Node”.
- Updated step 5 in the procedure “Remove Permanently or Remove and Replace DWDM Cards” of the chapter, “Upgrade, Add, and Remove Cards and Nodes”.
|
August 2011 |
- Updated the table “OTU2_XP Line Settings” in the chapter “Provision Transponder and Muxponder Cards”.
|
September 2011 |
- Updated a note in “NTP-G198 Create 1+1 Protection for GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Cards” in the chapter “Provision Transponder and Muxponder Cards”.
|
October 2011 |
- Updated the “DLP-G384 Provision the GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE QinQ Settings”, “DLP-G470 Provision the GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Class of Service (CoS) Settings”, “DLP-G380 Provision the GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Card Ethernet Settings”, and “DLP-G460 Enable MAC Address Learning on SVLANs for GE_XPE or 10GE_XPE Cards” procedures in the chapter "Provision Transponder and Muxponder Cards".
- Updated the “DLP-G471 Create an SVLAN Profile” in the chapter "Provision Transponder and Muxponder Cards".
- Updated information related to IB_5G in the chapter “Provision Transponder and Muxponder Cards”.
- Updated the section “DLP-G281 Configure the Node for RADIUS Authentication” in the chapter “Manage the Node”.
|
December 2011 |
- Updated the procedure “DLP-G76 Provision DCC/GCC Terminations” in the chapter “Create Circuits and Provisionable Patchcords”.
- Updated the following procedures in the chapter “Manage the Node”:
– NTP-G85 Modify or Delete OSC Terminations, DCC/GCC Terminations, and Provisionable Patchcords – DLP-G184 Change a DCC/GCC Termination – DLP-G185 Delete a DCC/GCC Termination |
February 2012 |
- Updated the procedure “DLP-G379 Change the GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Card Mode” in the chapter “Provision Transponder and Muxponder Cards”.
- Updated the Mode parameter in the table “ADM-10G Card Ethernet Settings” in the chapter “Provision Transponder and Muxponder Cards”.
- Updated the procedure “DLP-G278 Provision the Optical Line Rate” in the chapter “Provision Transponder and Muxponder Cards”.
|
March 2012 |
- Updated the bandwidth parameter in the procedure, “DLP-G383 Provision the GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Quality of Service Settings”.
- Added a note in the procedure “NTP-G242 Create an Internal Patchcord Manually” in the chapter “Turn Up a Node”.
|
April 2012 |
Added a note in the procedure “DLP-G368 Change the 10G Multirate Transponder Trunk Wavelength Settings” in the chapter “Provision Transponder and Muxponder Cards”. |
May 2012 |
- Added a note in the procedure “DLP-G507 Enable a Different GE_XP, 10GE_XP, GE_XPE, or 10GE_XPE Card as the Master Card” in the chapter “Provision Transponder and Muxponder Cards”.
- Updated the “Set Up SNMP” procedure in the chapter “Turn Up a Node”.
|
July 2012 |
Document Part Number revisioned to 78-18886-02 and a full length book-PDF was generated. |
July 2012 |
- Updated the table “Gigabit Ethernet RMON Variables” in the chapter “Provision Transponder and Muxponder Cards”.
- Updated the task “NTP-G130 Remove a DWDM Node” in the chapter “Upgrade, Add, and Remove Cards and Nodes”.
|
September 2012 |
- Added the “NTP-G333 Add an ADM-10G Card to an Existing Topology” in the chapter “Provision Transponder and Muxponder Cards”.
- Updated the procedures “NTP-G60 Create and Delete Overhead Circuits” and “DLP-G76 Provision DCC/GCC Terminations” in the chapter “Create Circuits and Provisionable Patchcords”.
- Updated the procedure “NTP-G38 Provision OSC Terminations” in the chapter “Turn Up a Node”.
|
October 2012 |
Added a note to “DLP-G264 Enable Node Security Mode” in the chapter, “Turn Up a Node”. |
November 2012 |
In the chapter “Maintain the Node”, updated the procedure “Inspect and Replace the Air Filter”. |
December 2012 |
Updated “NTP-G244 Perform the Four Degree ROADM Node with 40-SMR-2-C Cards Acceptance Test” in the chapter, “Perform Node Acceptance Tests”. |
January 2013 |
Updated the procedure “DLP-G351 Delete a Card in CTC” in the chapter, “Turn Up a Node”. |
March 2013 |
- Updated step 3 in the task, "DLP-G95 Set Up External or Line Timing" in the chapter, “Turn Up a Network”.
- Updated step 6 in the task, "DLP-G381 Provision the GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Layer 2 Protection Settings" in the chapter, “Provision Transponder and Muxponder Cards”.
|
May 2013 |
- Modified a note in the procedure, "NTP-G104 Restore the Database" in the chapter, "Maintain the Node".
- Added the procedure, “NTP-G341 Set Up Secure Access to the ONS 15454 TL1” in the chapter, “Turn Up a Node”.
|
June 2013 |
Added a footnote to the table, "MXP_MR_10DME_C or MXP_MR_10DME_L Ethernet Variables" in the chapter, "Provision Transponder and Muxponder Cards". |