|
|
AID |
Access identifier from the "ALL" section. All of the VC12 and Facility AIDs are supported |
MONTYPE |
Monitored type Parameter type is ALL_MONTYPE—monitoring type list |
• AISSP |
Alarm Indication Signal Seconds—Path |
• ALL |
All possible values |
• BBEP |
SDH Background Block Errors Path |
• BBE-PM |
OTN—Background Block Errors—Path Monitor Point |
• BBER |
SDH Background Block Error Ratio |
• BBER-PM |
OTN—Background Block Error Ratio—Path Monitor Point expressed as 1/10th of a percentage. |
• BBER-SM |
OTN—Background Block Error Ratio—Section Monitor Point expressed as 1/10th of a percentage. |
• BBE-SM |
OTN—Background Block Errors—Section Monitor Point |
• BIEC |
FEC—Bit Errors Corrected |
• BIT-EC |
The number of bit errors corrected by the FEC algorithm |
• CGV |
8B10B—Code Group Violations |
• CVCPP |
Coding Violations—CP-Bit Path |
• CVL |
Coding Violations—Line |
• CVP |
Coding Violations—Path |
• CVS |
Coding Violations—Section |
• CVV |
Coding Violations—Section |
• DCG |
8B10B—Data Code Groups |
• ESCPP |
Errored Seconds—CP—Bit Path |
• ESL |
Errored Seconds—Line |
• ESP |
Errored Seconds—Path |
• ES-PM |
OTN—Errored Seconds—Path Monitor Point |
• ESR |
Errored Second—Ratio |
• ESR-PM |
Errored Seconds Ratio—Path monitor Point expressed as 1/10th of a percentage |
• ESR-SM |
Errored Seconds Ratio—Section monitor Point expressed as 1/10th of a percentage |
• ESS |
Errored Seconds—Section |
• ES-SM |
OTN—Errored Seconds—Section Monitor Point |
• ESV |
Errored Seconds—VC Path |
• etherStatsBroadcastPkts |
The total number of good packets received that were directed to a multicast address |
• etherStatsCollisions |
Number of transmit packets that are collisions |
• etherStatsCRCAlignErrors |
The total number of packets received that have a length (excluding framing bits, but including frame check sequence [FCS] octets) of between 64 and 1518 octets |
• etherStatsDropEvents |
Number of received frames dropped at the port level |
• etherStatsFragments |
The total number of packets received that were less than 64 octets |
• etherStatsJabbers |
The total number of packets received that are longer than 1518 octets |
• etherStatsOctets |
The total number of octets of data |
• etherStatsOversizePkts |
The total number of packets received that are longer than 1518 octets |
• etherStatsPkts |
The total number of packets (including bad packets, broadcast packets, and multicast packets) received |
• etherStatsUndersizePkts |
The total number of packets received that are less than 64 octets |
• FCP |
Failure Count—Line |
• FC-PM |
OTN—Failure Count—Path Monitor Point |
• FC-SM |
OTN—Failure Count—Section Monitor Point |
• HP-AR |
Availability Ratio |
• HP-BBE |
High-Order Path Background Block Error |
• HP-BBER |
High-Order Path Background Block Error Ratio |
• HP-EB |
High-Order Path Errored Block |
• HP-ES |
High-Order Path Errored Second |
• HP-ESA |
High-Order Path Errored Seconds - A |
• HP-ESB |
High-Order Path Errored Seconds - B |
• HP-ESR |
High-Order Path Errored Second Ratio |
• HP-FC |
High-Order Path Failure Count |
• HP-NPJC-PDET |
High Order Path Negative Pointer Justification Count |
• HP-NPJC-PGEN |
High Order Path Pointer Justification Count Seconds |
• HP-OI |
Outage Intensity |
• HP-PJCDIFF |
High Order Path Pointer Justification Count Difference |
• HP-PJCS-PDET |
High Order Path Pointer Justification Count |
• HP-PPJC-PDET |
High Order Path Positive Pointer Justification Count |
• HP-PPJC-PGEN |
High Order Path, Positive Pointer Justification Count |
• HP-SEPI |
The number of SEP events in available time |
• HP-SES |
High-Order Path Severely Errored Seconds |
• HP-SESR |
High-Order Path Severely Errored Second Ratio |
• HP-UAS |
High-Order Path Unavailable Seconds |
• ifInBroadcastPkts |
Number of broadcast packets received since the last counter reset |
• ifInDiscards |
The number of inbound packets |
• ifInErrorBytePktss |
Receive Error Byte |
• ifInErrors |
The number of inbound packets (or transmission units) that contained errors |
• ifInFramingErrorPkts |
Receive Framing Error |
• ifInJunkInterPkts |
Receive Interpacket Junk |
• ifInMulticastPkts |
Number of multicast packets received since the last counter reset |
• ifInOctets |
Number of bytes transmitted since the last counter reset |
• ifInUcastPkts |
Number of unicast packets received since the last counter reset |
• ifOutBroadcastPkts |
Number of broadcast packets transmitted |
• ifOutDiscards |
The number of outbound packets |
• ifOutErrors |
The number of outbound packets (or transmission units) that could not be transmitted because of errors |
• ifOutMulticastPkts |
Number of multicast packets transmitted |
• ifOutPayloadCrcErrors |
Received payload (cyclic redundancy check) CRC errors |
• ifOutUcastPkts |
Number of unicast packets transmitted |
• IOS |
8B10B - Idle Ordered Sets |
• IPC |
Invalid Packet Count |
• LBCL-AVG |
Average Laser Bias current in micro A |
• LBCL-MAX |
Maximum Laser Bias current in micro A |
• LBCL-MIN |
Minimum Laser Bias current in micro A |
• LBCN |
Normalized Laser Bias Current for STM1-8 |
• LBCN-HWT |
Laser Bias current |
• LBCN-LWT |
Laser Bias current |
• LOSSL |
Loss of Signal Seconds—Line |
• LP-BBE |
Low-Order Path Background Block Error |
• LP-BBER |
Low-Order Path Background Block Error Ratio |
• LP-EB |
Low-Order Path Errored Block |
• LP-ES |
Low-Order Path Errored Second |
• LP-ESA |
Low-Order Path Errored Seconds - A |
• LP-ESB |
Low-Order Path Errored Seconds - B |
• LP-ESR |
Low-Order Path Errored Second Ratio |
• LP-FC |
Low-Order Path Failure Count |
• LP-NPJC-DET |
Low Order Negative Pointer Justification Count, Detected |
• LP-NPJC-GEN |
Low Order Negative Pointer Justification Count, Generated |
• LP-PPJC-DET |
Low Order Positive Pointer Justification Count, Detected |
• LP-PPJC-GEN |
Low Order positive Pointer Justification Count, Generated |
• LP-SEP |
A sequence of between 3 to 9 consecutive severely errored seconds (SES) |
• LP-SEPI |
Low-Order Path Severely Errored Period Intensity |
• LP-SES |
Low-Order Path Severely Errored Seconds |
• LP-UAS |
Low-Order Path Unavailable Seconds |
• MS-PSC |
Multiplex Section-Protection switch count |
• MS-PSD |
Multiplex Section-Protection switch duration |
• NIOS |
8B10B—Non Idle Ordered Sets |
• NPJC-PDET |
Negative Pointer Justification Count, Path Detected |
• NPJC-PGEN |
Negative Pointer Justification Count, Path Generated |
• OPR-AVG |
Average Receive Power in 1/10 micro W |
• OPR-MAX |
Maximum Receive Power in 1/10 micro W |
• OPR-MIN |
Minimum Receive Power in 1/10 micro W |
• OPRN |
Normalized Optical Receive Power for STM1-8 |
• OPRN-MAX |
Maximum value for OPRN |
• OPRN-MIN |
Minimum value for OPRN |
• OPT-AVG |
Average Transmit Power in 1/10 micro W |
• OPT-MAX |
Maximum Transmit Power in 1/10 micro W |
• OPT-MIN |
Minimum Transmit Power in 1/10 micro W |
• OPTN |
Normalized value for Optical Power Transmitted for STM1-8 card |
• OPTN-MAX |
Maximum value for OPTN |
• OPTN-MIN |
Minimum value for OPTN |
• OPWR-AVG |
Optical Power—Average Interval Value in 1/10th of dBm |
• OPWR-MAX |
Optical Power—Maximum Interval Value in 1/10th of dBm |
• OPWR-MIN |
Optical Power—Minimum Interval Value in 1/10th of dBm |
• PPJC-PDET |
Positive Pointer Justification Count, Path Detected |
• PPJC-PGEN |
Positive Pointer Justification Count, Path Generated |
• PSC |
Protection Switching Count |
• PSC-R |
Protection Switching Count—Ring |
• PSC-S |
Protection Switching Count—Span |
• PSC-W |
Protection Switching Count—Working |
• PSD |
Protection Switching Duration |
• PSD-R |
Protection Switching Duration—Ring |
• PSD-S |
Protection Switching Duration—Span |
• PSD-W |
Protection Switching Duration—Working |
• SASCPP |
Severely Errored Framing/AIS Second—CP-Bit Path |
• SASP |
Severely Errored Framing/AIS Seconds Path |
• SEFS |
Severely Errored Framing Seconds |
• SESCPP |
Severely Errored Second—CP-Bit Path |
• SESL |
Severely Errored Second—Line |
• SESP |
Severely Errored Second—Path |
• SES-PM |
OTN—Severely Errored Second—Path |
• SESR |
Severely Errored Second—Ratio |
• SESR-PM |
OTN—Severely Errored Second Ratio—Path Monitor Point expressed as 1/10th of a percentage |
• SESR-SM |
OTN—Severely Errored Second Ratio—Section Monitor Point expressed as 1/10th of a percentage |
• SESS |
Severely Errored Second—Section |
• SES-SM |
OTN—Severely Errored Second—Section Monitor Point |
• SESV |
Severely Errored Second—VC Path |
• UASCPP |
Unavailable Second—CP-Bit Path |
• UASL |
Unavailable Second—Line |
• UASP |
Unavailable Second—Path |
• UAS-PM |
OTN—Unavailable Second—Path Monitor Point |
• UAS-SM |
OTN—Unavailable Second—Section Monitor Point |
• UASV |
Unavailable Second—VC Path |
• UNC-WORDS |
FEC—Uncorrectable Words |
• VPC |
Valid Packet Count |
lSTM |
Location associated with a particular command in reference to the entity identified by the AID Parameter type is LOCATION—the location where the action is to take place |
• FEND |
Action occurs on the Far End of the facility |
• NEND |
Action occurs on the Near End of the facility |
DIRN |
Direction relative to the entity identified by the AID. Defaults to ALL, which means that the command initializes all of the registers irrespective of the PM direction Parameter type is DIRECTION—transmit and receive directions |
• RCV |
Receive direction only |
TMPER |
Accumulation time period for performance counters. A null value defaults to 15-MIN. Defaults to 15-MIN Parameter type is TMPER—accumulation time period for the performance management center |
• 1-DAY |
Performance parameter accumulation interval length; every 24-hours. For SDH PM data only one day of history data is available. For RMON managed PM data seven days of history data are available. |
• 1-HR |
Performance parameter accumulation interval length; every 1 hour. This is only applicable to RMON managed PM data. There are 24 hours of history data available. |
• 1-MIN |
Performance parameter accumulation interval length; every 1 minute. This is only applicable to RMON managed PM data. There are 60 minutes of history available. |
• 15-MIN |
Performance parameter accumulation interval length; every 15 minutes. There are 32 15-MIN buckets of history data available for this accumulation interval length. |
• RAW-DATA |
Performance parameter accumulation interval length; starting from the last time the counters were cleared. This is only applicable to RMON managed PMs. |