Viewing and Adding Devices

This chapter contains the following sections:

Viewing and Adding Devices

You can view all the devices added to NDB on the Nodes Learned tab. The following information about each device is displayed on the Node Learned tab:

  • Name of the node

  • ID of the node

  • IP Address of the node

  • Platform information

  • Number of ports on the node

You can click on a node name to upate the node information. The Update Node Information window opens, you can update the following device information:

  • Tier: Select the tier of the node from the Tier drop-down list: Unknown , Access , Distribution , or Core .

  • Operation Mode: Select how the traffic is handled based on the flows for OpenFlow devices:

    • Allow reactive forwarding—No default flows are programmed. How the traffic that does not match a flow is handled depends on the switch configuration.

    • Proactive forwarding only—Punt Link Layer Discovery Protocol (LLDP) packets flow is programmed on the device.

Managing a Device in NDB

You can add, remove, or edit a device using NDB.

  • Adding a Device

  • Removing a Device

  • Rediscovering a Device

  • Managing Profile for a Device

Adding a Device

Complete these steps to add a device.

Procedure

Step 1

Navigate to ADMINISTRATION > Device Connections tab.

Step 2

Click Add Device, the Add Device dialog box opens.

Step 3

In the Add Device dialog box, enter the following details:

Table 1. New Device Details

Field

Description

IP address/Hostname

The name or IP address of the device. To add multiple devices, add the hostnames or IP Addresses separated with the comma. For example, ndb1.cisco.com, ndb2.cisco.com, ndb3.cisco.com.

Username/Password

Select this option to add a device using username and password credentials.

Profile

Select this option to add a device using a profile. For more information about adding a device using profiles, see Profile Management

Username

Username for authenitcating the device.

Password

Password for authenticating the device.

Connection Type

Type of connection supported. Currently, NXAPI is supported.

Port

The device communication port. For example, use port 80 for NX-API over HTTP and 443 for HTTPS.

Set Auxiliary Node

Indicates whether this NX-API connection is Auxillary for the OpenFlow device.

Device Prerequisites

To set the device to default configuration required for NX-API type of connection. This option is available for NXAPI connection type only without Auxiliary mode. To know more about the Device Prerequisites, see Device Prerequisites section.

Step 4

Click Add Device to create and add the new device to NDB. The new device is listed on the DEVICE CONNECTION tab.

Global deny ACLs are automatically added to all non-configured interfaces (Edge SPAN/TAP, Packet Truncation, Remote Source, and Local and Remote Monitor) on a device. By default, Global Deny ACL feature is enabled on all the devices. You can disable the Global Deny ACL feature by setting the configure.global.acls parameter to false in the config.ini file. Ensure that you restart NDB after making changes in the configuration file.

By default, deny ACL is enabled on all the Inter Switch Links (ISL) interfaces causig all the traffic in the ISL interfaces to be droped if there is no connection installed. The following connections are installed on the ISL interfaces:

  • Default-Deny-ISL connection with Default-Deny-All, Default-Deny-MPLS, and Default-Deny-ARP filters. This connection is supported on all the types of switches in NXAPI mode.

  • Default-Deny-ISL-ICMP connection with Default-Deny-ICMP and Default-Deny-ICMP-All filters. This connection is supported on Nexus 9200, 9300EX, 9300FX, 9500EX, and 9500FX switches in NXAPI mode.

You can disable deny ACL on all the ISL interfaces by setting the configure.global.acls parameter to false in the config.ini file. Ensure that you restart NDB after making changes in the configuration file.

You can disable Global deny ACL or ISL deny ACL during the CLI upgrade or configuration upload by using the CLI upgrade command and setting the configure.global.acls parameter to false in the config.ini file. For example:
xnc upgrade --perform --target-home {xnc_directory_to_be_upgraded} [--verbose] [--backupfile {xnc_backup_location_and_zip_filename}]

Path:<NDBhome>/configuration/configure.global.acls=false
Note 

You can also disable Global deny ACL or ISL deny ACL by uploading the configuration in a Web browser.

Removing a Device

To remove a device from NDB, complete these steps

Procedure

Step 1

Navigate to Device Connections tab.

Step 2

Select the device to remove from the table.
Step 3

Click Remove Devices. The Remove Devices dialog box opens.

Step 4

Verify the selected device(s) in the Remove Devices dialog box and click either of the two options:

  • Remove Device: Use this option to remove the device connection from NDB while retaining the device configuration.

  • Purge & Remove Device: Uset this option to remove the device connection from NDB along with the device configuration.

Rediscovering a Device

To rediscover a device from NDB, complete these steps:

Procedure

Step 1

Navigate to Device Connections tab.

Step 2

Select the device(s) to rediscover from the table under the Device Connections tab.

Step 3

Click Rediscover Devices, the Redicover Devices window appears.

Step 4

Verify the selected devices in the Redicover Devices window.

Step 5

Click Rediscover Devices to rediscover the device(s).

Managing Profile for a Device

You can attach a profile to an exisitng device or change the profile attached to a device using NDB. Complete these steps to add or change a profile to a device:


Note

This feature is currently supported in NXAPI mode only.

Procedure

Step 1

Navigate to Device Connections tab.

Step 2

Click Add/Change Profile to Device, the Add/Change Profile to Device window appears.

Step 3

Verify the selected devices in the Add/Change Profile to Device window. You can edit the following details in the Add/Change Profile to Device window:

  • Profile: Select a profile to attach. For more information about the profiles, see Profile Management section.

  • Connection Type: Specify the supported connection type. Currently, NXAPI is supported.

  • Port: The device communication port. For example, use port 80 for NX-API over HTTP and 443 for HTTPS.

Device Prerequisites

Starting with Cisco NDB release 3.8, NDB pushes basic configuration to a newly added switch into NDB. Manual configuration of the NX-API devices to make it ready for NDB is not required. As a part of the adding a new device, the prerequisites are configured by NDB on the devices.

You need to ensure that NX-API is enabled on the new device for NDB to push prerequisite configuration successfully.

Following configurations are pushed into the new switch by NDB.

  • TCAM configurations based on the device platform

  • MST mode is enabled on the Spanning Tree

  • Basic VLAN Configuration

  • LLDP feature is enabled (only for the centralized mode of NDB)


Note

Device is rebooted after all the configurations are successfully pushed by NDB. The device reboot is required because of the TCAM configurations. The reboot is supported from NX-OS is 9.2(3) and above

The Device Prerequisites can be configured when you add or edit a device, or when you add or change profile to device.

Profile Management

Starting with Cisco NDB release 3.8, you can add, edit, or delete a profile through NDB. A profile allow you to manage multiple switches attached to a NDB. You can attach multiple switches to a profile. The profile configuration is applied to all the member switches.

Adding a Profile

Complete these steps to add a profile:

Procedure

Step 1

Navigate to ADMINSTRATION > User Management.

Step 2

On the User Management page, click Profile tab.

Step 3

Click Add Profile to open the Add Profile dialog-box.

Step 4

Enter name of the profile in the Profile Name text-field.

Step 5

Enter the user name to be configured for the member switches in the User Name text-field.

Step 6

Enter the password to be configured for the member switches in the Password text-field.

Step 7

Click Create to create a new profile.

Editing a Profile

To edit a profile using NDB, complete these steps:

Procedure

Step 1

Navigate to ADMINSTRATION > User Management > Profile tab.

Step 2

Click Edit to edit a profile. The Edit Profile dialog box opens.

Step 3

Enter new name of the profile in the Profile Name text-field.

Step 4

Enter the new user name to be configured for the member switches in the User Name text-field.

Step 5

Enter the new password to be configured for the member switches in the Password text-field.

Step 6

Click Submit. All the devices that are part of the profile are rediscovered with the updated credentials.

Deleting a Profile

Complete these steps to delete a profile:

Procedure

Step 1

Navigate to ADMINSTRATION > User Management > PROFILE.

Step 2

On the Profile page, click Delete for the profile to delete it.The deleted profile is removed from the Profile page.