|
|
UNIDENTIFIED |
Normal condition |
ENV |
Failure detected external to the NE |
ENV |
External error |
UNIDENTIFIED |
Excessive switching |
UNIDENTIFIED |
Incoming failure condition |
AIS |
Alarm indication signal |
AIS |
Alarm indication signal—line |
AIS |
Alarm indication signal—path |
FOP_APS |
APS channel failure |
FOP_APS |
Byte failure |
FOP_APS |
Protection switching channel match failure |
FOP_APS |
Automatic protection switch mode mismatch |
FOP_APS |
Far-end protection line failure |
UNIDENTIFIED |
Bipolar violation |
UNIDENTIFIED |
Carrier loss on the LAN |
UNIDENTIFIED |
STS concatenation error |
UNIDENTIFIED |
Excess collisions on the LAN |
UNIDENTIFIED |
Facility failure |
UNIDENTIFIED |
Far-end block error |
LOF |
Loss of frame |
LOP |
Loss of pointer |
LOP |
Loss of pointer—path |
LOS |
Loss of signal |
UNIDENTIFIED |
Out of frame |
UNIDENTIFIED |
Path selector failure |
RAI |
Remote alarm indication |
RAI |
Remote failure indication |
RAI |
Remote failure indication—line |
RAI |
Remote failure indication—path |
BER_SD |
Signal degrade |
UNIDENTIFIED |
Severely errored frame |
UNIDENTIFIED |
Invalid alarm |
BER_SF |
Signal failure |
UNIDENTIFIED |
Signal label mismatch failures |
UNIDENTIFIED |
Payload defect indication |
UNIDENTIFIED |
Payload defect indication—path |
PLM |
Payload label mismatch—path |
UNEQ |
Unequipped—path |
TIMING_SYNCH |
Loss of synchronization |
TIMING_SYNCH |
Out of synchronization |
TIMING_SYNCH |
Primary synchronization reference failure |
TIMING_SYNCH |
Secondary synchronization reference failure |
TIMING_SYNCH |
Third synchronization reference failure |
TIMING_SYNCH |
Fourth synchronization reference failure |
TIMING_SYNCH |
Fifth synchronization reference failure |
TIMING_SYNCH |
Sixth synchronization reference failure |
UNIDENTIFIED |
Outgoing failure condition |
RAI |
Remote defect indication—line |
RAI |
Remote defect indication—path |
TIMING_SYNCH |
Free running synchronization mode |
TIMING_SYNCH |
Holdover synchronization mode |
EQPT |
Internal fault |
UNIDENTIFIED |
Internal error |
UNIDENTIFIED |
Internal message error |
EQPT |
Mismatch of equipment and attributes |
UNIDENTIFIED |
Watchdog timer timeout |
ENV |
Software fault or failure |
ENV |
Software fault—data integrity fault |
UNIDENTIFIED |
Program failure |
EQPT |
Control equipment failure |
EQPT |
Control processor failure |
EQPT |
Working memory failure |
EQPT |
Interconnection equipment failure |
EQPT |
Time slot interchange equipment failure |
EQPT |
Equipment failure |
EQPT |
High temperature |
EQPT |
Facility termination equipment failure |
EQPT |
Automatic laser shutdown |
UNIDENTIFIED |
Failure to release from protection |
EQPT |
Receiver failure |
EQPT |
Transmit failure |
UNIDENTIFIED |
Failure to switch to protection |
EQPT |
Equipment unit plug-in |
ENV |
Internal power failure |
ENV |
Fuse alarm |
TIMING_SYNCH |
Synchronization unit failure |
EQPT |
Synchronization switching equipment failure |
EQPT |
Equipment unit unplugged |
EQPT |
Manually caused abnormal condition |
UNIDENTIFIED |
Manual alarm cutoff |
UNIDENTIFIED |
Procedural error |
EQPT |
Improper removal |
UNIDENTIFIED |
Protection unit not available |
UNIDENTIFIED |
Protection switch |
UNIDENTIFIED |
Recovery or service protection action has been initiated |
UNIDENTIFIED |
Automatic system reset |
UNIDENTIFIED |
Cold restart |
UNIDENTIFIED |
Forced switch back to working |
UNIDENTIFIED |
Forced switch to protection |
UNIDENTIFIED |
Initialization initiated |
UNIDENTIFIED |
Lockout of protection |
UNIDENTIFIED |
Lockout of working |
UNIDENTIFIED |
Manual system reset |
UNIDENTIFIED |
Manual switch to internal clock |
UNIDENTIFIED |
Manual switch to primary reference |
UNIDENTIFIED |
Manual switch to secondary reference |
UNIDENTIFIED |
Manual switch to third reference |
UNIDENTIFIED |
Manual switch to fourth reference |
UNIDENTIFIED |
Manual switch to fifth reference |
UNIDENTIFIED |
Manual switch to sixth reference |
UNIDENTIFIED |
Manual switch back to working |
UNIDENTIFIED |
Manual switch to protection |
UNIDENTIFIED |
Power fail restart |
EQPT |
Software download in progress |
TIMING_SYNCH |
Switch to internal clock |
TIMING_SYNCH |
Switch to primary reference |
TIMING_SYNCH |
Switch to secondary reference |
TIMING_SYNCH |
Switch to third reference |
TIMING_SYNCH |
Switch to fourth reference |
TIMING_SYNCH |
Switch to fifth reference |
TIMING_SYNCH |
Switch to sixth reference |
UNIDENTIFIED |
Switched back to working |
UNIDENTIFIED |
Switched to protection |
UNIDENTIFIED |
Warm restart |
UNIDENTIFIED |
Ring is in wait-to-restore state |
EQPT |
Primary nonvolatile backup memory failure |
EQPT |
Secondary nonvolatile backup memory failure |
EQPT |
Control bus failure |
EQPT |
Control communications equipment failure |
UNIDENTIFIED |
Loopback |
UNIDENTIFIED |
Loopback, network |
UNIDENTIFIED |
Loopback, terminal |
ENV |
Fan failure |
DCC_FAILURE |
SDCC termination failure |
UNIDENTIFIED |
Loopback facility |
EQPT |
Payload bus failure to I/O slot 1 to 17 (XCON slot 8) |
EQPT |
Control bus 1 to 2 failure |
EQPT |
Invalid MAC address |
EQPT |
Board failure |
EQPT |
Diagnostics failure |
EQPT |
Medium access control failure |
UNIDENTIFIED |
Duplicate node ID |
UNIDENTIFIED |
Failure to switch to protection—ring |
UNIDENTIFIED |
Failure to switch to protection—span |
UNIDENTIFIED |
Manual switch back to working—ring |
UNIDENTIFIED |
Manual switch back to working—span |
UNIDENTIFIED |
Manual switch to protection—ring |
UNIDENTIFIED |
Manual switch to protection—span |
UNIDENTIFIED |
Forced switch back to working—ring |
UNIDENTIFIED |
Forced switch back to working—span |
UNIDENTIFIED |
Forced switch to protection—ring |
UNIDENTIFIED |
Forced switch to protection—span |
UNIDENTIFIED |
Lockout of protection—ring |
UNIDENTIFIED |
Lockout of protection—span |
UNIDENTIFIED |
Lockout of working—ring |
UNIDENTIFIED |
Lockout of working—span |
UNIDENTIFIED |
Ring is squelching traffic |
FOP_APS |
Inconsistent APS code |
FOP_APS |
Node ID mismatch |
FOP_APS |
Default K byte |
FOP_APS |
Connection loss |
EQPT |
TCC [A...B] to shelf slot 1...17 [DROP 1...8 | TRUNK 1...2 | TCC A...B | XCON A...B] communication failure |
TIMING_SYNCH |
Fast start synchronization mode |
FOP_APS |
Improper APS code |
UNIDENTIFIED |
BLSR out of sync |
AIS |
Alarm indication signal—VT |
RAI |
Remote failure indication—VT |
PLM |
Signal label mismatch failure—payload label mismatch—VT |
UNEQ |
Signal label mismatch failure—unequipped—VT |
UNIDENTIFIED |
Peer state mismatch |
EQPT |
Facility termination equipment—receiver missing |
EQPT |
Facility termination equipment—transmitter missing |
LOP |
Loss of pointer—VT |
LINK DOWN |
Embedded operations channel failure—link down |
TIMING_SYNCH |
Failed to receive synchronization status message |
TIMING_SYNCH |
Synchronization status messages are disabled on this interface |
TIMING_SYNCH |
Primary reference source—stratum 1 traceable |
TIMING_SYNCH |
Synchronized—traceability unknown |
TIMING_SYNCH |
Stratum 2 traceable |
TIMING_SYNCH |
Transit node clock traceable |
TIMING_SYNCH |
Stratum 3E traceable |
TIMING_SYNCH |
Stratum 3 traceable |
TIMING_SYNCH |
SONET minimum clock traceable |
TIMING_SYNCH |
Stratum 4 traceable |
TIMING_SYNCH |
Do not use for synchronization |
TIMING_SYNCH |
Reserved for network synchronization use |
UNIDENTIFIED |
Failure to switch to protection—path |
UNIDENTIFIED |
Manual switch of working facility—equipment to protection—path |
UNIDENTIFIED |
Working facility—equipment forced to switch to protection—path |
UNIDENTIFIED |
Lockout of protection—path |
UNIDENTIFIED |
Automatic UPSR switch caused by [AIS | LOP | UNEQ | PDI | SFBER | SDBER] |
UNIDENTIFIED |
DS3 idle condition |
UNIDENTIFIED |
DS1 loopback due to FEAC command |
UNIDENTIFIED |
DS1 loopback command sent to far end |
UNIDENTIFIED |
DS3 loopback due to FEAC command |
UNIDENTIFIED |
DS3 loopback command sent to far end |
UNIDENTIFIED |
DS2 loopback due to far-end command |
UNIDENTIFIED |
DS2 loopback command sent to far end |
ENV |
Far-end AIS |
LOS |
Far-end multiple DS1 LOS detected on DS3 |
ENV |
Far-end DS1 equipment failure—non-service affecting |
ENV |
Far-end DS1 equipment failure—service affecting |
LOS |
Far-end single DS1 LOS |
ENV |
Far-end DS3 equipment failure—non-service affecting |
ENV |
Far-end DS3 equipment failure—service affecting |
ENV |
Far-end common equipment failure—non-service affecting |
UNIDENTIFIED |
Far end idle |
LOS |
Far end LOS |
LOF |
Far end LOF |
UNIDENTIFIED |
Performance monitor threshold crossing alert |
UNIDENTIFIED |
Ethernet bridge is new root of spanning tree |
UNIDENTIFIED |
Ethernet bridge topology change |
UNIDENTIFIED |
BLSR tables resynchronized |
ENV |
System reboot |
UNIDENTIFIED |
Manual switch request on facility—equipment |
UNIDENTIFIED |
Forced switch request on facility or equipment |
UNIDENTIFIED |
Lockout switch request on facility—equipment |
UNIDENTIFIED |
RMON histories and alarms reset reboot |
UNIDENTIFIED |
RMON alarm |
LOS |
Video interface card loss of video IF signal |
LOS |
VIC loss of video baseband signal |
LOS |
VIC loss of audio FM signal |
LOS |
VIC loss of audio baseband channel [1...4] signal |
TIM |
STS path trace identifier mismatch |
ENV |
NE power failure at connector A |
ENV |
NE power failure at connector B |
EQPT |
Free memory on card very low |
EQPT |
Free memory on card near zero |
UNIDENTIFIED |
Exercise request on ring |
UNIDENTIFIED |
Exercise request on span |
UNIDENTIFIED |
Squelching path |
UNIDENTIFIED |
Extra traffic preempted |
UNIDENTIFIED |
Far-end lockout of working—ring |
UNIDENTIFIED |
Far-end lockout of working—span |
UNIDENTIFIED |
Far-end lockout of protection—ring |
UNIDENTIFIED |
Far-end lockout of protection—all spans |
UNIDENTIFIED |
Far-end working facility forced to switch to protection—ring |
UNIDENTIFIED |
Far-end working facility forced to switch to protection—span |
UNIDENTIFIED |
Far-end manual switch of working facility to protection—ring |
UNIDENTIFIED |
Far-end manual switch of working facility to protection—span |
UNIDENTIFIED |
Far-end exercising ring |
UNIDENTIFIED |
Far-end exercising span |
ENV |
Far-end BER threshold passed for signal failure—ring |
ENV |
Far-end BER threshold passed for signal failure—span |
ENV |
Far-end BER threshold passed for signal degrade—ring |
ENV |
Far-end BER threshold passed for signal degrade—span |
ENV |
APS channel—far-end protection line signal degrade |
UNIDENTIFIED |
Ring switch is active on the east side |
UNIDENTIFIED |
Ring switch is active on the west side |
UNIDENTIFIED |
Span switch is active on the east side |
UNIDENTIFIED |
Span switch is active on the west side |
UNIDENTIFIED |
Unidirectional full pass-through is active |
UNIDENTIFIED |
Bidirectional full pass-through is active |
UNIDENTIFIED |
K bytes pass-through is active |
UNIDENTIFIED |
Ring is segmented |
UNIDENTIFIED |
Ring topology is under construction |
UNIDENTIFIED |
Lockout of protection—all spans |
UNIDENTIFIED |
Far-end of fiber is provisioned with different ring ID |
UNIDENTIFIED |
Both ends of fiber provisioned as east or both as west |
SECURITY_VIOLATION |
Security—invalid login—see audit trail |
UNIDENTIFIED |
Autonomous messages inhibited |
UNIDENTIFIED |
Traffic storm on LAN; LAN temporarily disabled |
UNIDENTIFIED |
REPT^DBCHG messages inhibited |
SECURITY_VIOLATION |
Security—user ID has expired |
EQPT |
Partial fan failure |
UNIDENTIFIED |
Force switch request on ring |
UNIDENTIFIED |
Force switch request on span |
UNIDENTIFIED |
Lockout switch request on ring |
UNIDENTIFIED |
Lockout switch request on span |
UNIDENTIFIED |
Manual switch request on ring |
UNIDENTIFIED |
Manual switch request on span |
EQPT |
Peer-to-peer slot communication failure |
EQPT |
Peer-to-peer slot communication failure |
EQPT |
TCC A to shelf slot communication failure |
EQPT |
TCC B to shelf slot communication failure |
EQPT |
Interconnection equipment failure—working XC payload bus |
EQPT |
Interconnection equipment failure—protect XC payload bus |
EQPT |
Inhibit switch to protect request on equipment |
EQPT |
Inhibit switch to working request on equipment |
BER_SD |
BER threshold exceeded for signal degrade—line |
BER_SD |
BER threshold exceeded for signal degrade—path |
BER_SF |
BER threshold exceeded for signal failure—line |
BER_SF |
BER threshold exceeded for signal failure—path |
UNIDENTIFIED |
Exercising ring successfully |
UNIDENTIFIED |
Exercising span successfully |
UNIDENTIFIED |
Span is in wait-to-restore state |
EQPT |
Peer card not responding |
UNIDENTIFIED |
Exercise request on ring failed |
UNIDENTIFIED |
Exercise request on span failed |
UNIDENTIFIED |
Far-end lockout of protection—span |
EQPT |
Manufacturing data memory (EEPROM) failure |
EQPT |
Replaceable equipment/unit is missing |
ENV |
Software download failure |
TIM |
TIM section—trace identifier mismatch failure |
AIS |
AIS—multiplex section—alarm indication signal |
RAI |
RFI—multiplex section—remote failure/alarm indication |
TIM |
TIM—high order—trace identifier mismatch failure |
AU_AIS |
AIS—administration unit—alarm indication signal |
LOP |
LOP—administration unit—loss of pointer |
UNEQ |
SLMF—unequipped high order—path unequipped |
PLM |
SLMF—PLM high order—path label mismatch |
RAI |
RFI—high order—remote failure/alarm indication |
LOP |
LOP—tributary unit—loss of pointer |
TU-AIS |
AIS—tributary unit—alarm indication signal |
UNEQ |
SLMF—unequipped low order—path unequipped |
PLM |
SLMF—PLM low order—path label mismatch |
TIM |
TIM low order—trace identifier mismatch failure |
RAI |
RFI—low order—remote failure/alarm indication |
TIMING_SYNCH |
G811—primary reference clock traceable |
TIMING_SYNCH |
G812—transit node clock traceable |
TIMING_SYNCH |
G812—local node clock traceable |
TIMING_SYNCH |
G813—synchronous equipment timing source traceable |
UNIDENTIFIED |
E1 loopback due to FEAC command |
UNIDENTIFIED |
E1 loopback command sent to far end |
UNIDENTIFIED |
E3 loopback due to FEAC command |
ENV |
Far-end multiple E1 LOS detected on E3 |
ENV |
Far-end E1 equipment failure non-service affecting |
ENV |
Far-end E1 equipment failure service affecting |
ENV |
Far-end single E1 LOS |
ENV |
Far-end E3 equipment failure service affecting |
UNIDENTIFIED |
E3 loopback command sent to far end |
ENV |
Far-end E3 equipment failure non-service affecting |
ENV |
Low voltage—battery A |
ENV |
High voltage—battery A |
ENV |
Low voltage—battery B |
ENV |
High voltage—battery B |
UNIDENTIFIED |
Procedural error—MS-SPRing out of sync |
UNIDENTIFIED |
MS-SPRing tables resynchronized |
UNIDENTIFIED |
Automatic SNCP switch caused by [AIS | LOP | UNEQ | PDI | SFBER | SDBER] |
UNIDENTIFIED |
STM concatenation error |
UNIDENTIFIED |
E3 idle condition |
UNIDENTIFIED |
IOS config copy failed |
UNIDENTIFIED |
IOS config copy in progress |
UNIDENTIFIED |
Alarms suppressed by user command |
UNIDENTIFIED |
Alarms suppressed for maintenance |
UNIDENTIFIED |
— |
UNIDENTIFIED |
Synchronization reference frequency out of bounds |
UNIDENTIFIED |
Ether Tx excess flow control |
UNIDENTIFIED |
Ether Tx oversubscribed |
UNIDENTIFIED |
Transport layer failure |
UNIDENTIFIED |
Ether Rx excess flow control |
UNIDENTIFIED |
Ether Rx oversubscribed |
UNIDENTIFIED |
Ether Tx underrun |
UNIDENTIFIED |
SNTP host failure |
UNIDENTIFIED |
DS3 frame format mismatch |
UNIDENTIFIED |
Alarms/events suppressed for this object |
BER_SD |
BER threshold exceeded for signal degrade—high order |
BER_SF |
BER threshold exceeded for signal failure—high order |
BER_SD |
BER threshold exceeded for signal degrade—low order |
BER_SF |
BER threshold exceeded for signal failure—low order |
UNIDENTIFIED |
Failure to switch to protection—high-order path |
UNIDENTIFIED |
Failure to switch to protection—low-order path |
UNIDENTIFIED |
Wait to restore |
ENV |
Extreme high voltage—battery A |
ENV |
Extreme low voltage—battery A |
ENV |
Extreme high voltage—battery B |
ENV |
Extreme low voltage—battery B |
UNIDENTIFIED |
Switching matrix module failure |
UNIDENTIFIED |
Signaling unable to set up circuit |
UNIDENTIFIED |
RSVP hello FSM to neighbor down |
UNIDENTIFIED |
LMP hello FSM to control channel down |
UNIDENTIFIED |
LMP neighbor discovery has failed |
UNIDENTIFIED |
Unauthorized incoming signaling request |
UNIDENTIFIED |
Signaled circuit going down |
UNIDENTIFIED |
Autonomous PM report message inhibited |
EQPT |
I/O slot to XCON communication failure |
UNIDENTIFIED |
Forced switch to primary reference |
UNIDENTIFIED |
Forced switch to secondary reference |
UNIDENTIFIED |
Forced switch to third reference |
UNIDENTIFIED |
Forced switch to internal clock |
LOM |
LOF—administration unit—loss of multiframe |
UNIDENTIFIED |
Admin logout of user |
UNIDENTIFIED |
User locked out |
UNIDENTIFIED |
Admin lockout of user |
UNIDENTIFIED |
Admin lockout clear |
SECURITY_VIOLATION |
Security—invalid login—username—see audit log |
SECURITY_VIOLATION |
Security—invalid login—password—see audit log |
SECURITY_VIOLATION |
Security—invalid login—locked out—see audit log |
SECURITY_VIOLATION |
Security—invalid login—already logged on—see audit log |
UNIDENTIFIED |
Login of user |
UNIDENTIFIED |
Automatic logout of idle user |
UNIDENTIFIED |
Logout of user |
UNIDENTIFIED |
Cross-connect loopback |
UNIDENTIFIED |
Error in startup config |
UNIDENTIFIED |
No startup config |
EQPT |
Laser approaching end of life |
UNIDENTIFIED |
Database backup failed |
UNIDENTIFIED |
Database restore failed |
UNIDENTIFIED |
8B10B out of sync |
AIS |
ODUk—alarm indication signal |
AIS |
OTUk—alarm indication signal |
UNIDENTIFIED |
OTUk—backward defect indicator |
UNIDENTIFIED |
ODUk—backward defect indicator |
UNIDENTIFIED |
FEC uncorrected word |
UNIDENTIFIED |
GCC embedded operation channel failure |
UNIDENTIFIED |
OTUk—incoming alignment error |
UNIDENTIFIED |
ODUk—locked defect—PM |
LOM |
Loss of multiframe |
UNIDENTIFIED |
ODUk—open connection indication |
PLM |
Payload type identifier mismatch |
TIM |
ODUk—trail trace identifier mismatch |
TIM |
OTUk—trail trace identifier mismatch |
EQPT |
Equipment high laser bias |
EQPT |
Equipment high laser temp |
EQPT |
Equipment high laser Peltier |
EQPT |
Equipment high Rx power |
EQPT |
Equipment high Tx power |
EQPT |
Equipment high Rx temperature |
EQPT |
Equipment low Tx temperature |
EQPT |
Equipment high transceiver voltage |
EQPT |
Equipment low laser bias |
EQPT |
Equipment low laser temp |
EQPT |
Equipment low laser Peltier |
EQPT |
Equipment low Rx power |
EQPT |
Equipment low Tx power |
EQPT |
Equipment low transceiver voltage |
EQPT |
Equipment Rx locked |
EQPT |
Equipment squelched |
EQPT |
Equipment Tx locked |
BER_SF |
OTUk—signal failure |
BER_SF |
ODUk—signal failure |
BER_SD |
OTUk—signal degrade |
BER_SD |
ODUk—signal degrade |
UNIDENTIFIED |
Pluggable port missing |
UNIDENTIFIED |
Pluggable port rate mismatch |
SECURITY_VIOLATION |
Pluggable port security code mismatch |
UNIDENTIFIED |
TCI not selected |
UNIDENTIFIED |
TCI 1 clock failure |
UNIDENTIFIED |
ODUk—backward defect indicator |
UNIDENTIFIED |
ODUk—open connection indication |
UNIDENTIFIED |
ODUk—locked defect—[TCM1 | TCM2] |
AIS |
ODUk—alarm indication signal |
TIM |
ODUk—trail trace identifier mismatch |
BER_SD |
ODUk—signal degrade—[TCM1 | TCM2] |
BER_SF |
ODUk—signal failure—[TCM1 | TCM2] |
UNIDENTIFIED |
ODUk—open connection indication |
UNIDENTIFIED |
ODUk—locked defect—TCM1 |
AIS |
ODUk—alarm indication signal |
TIM |
ODUk—trail trace identifier mismatch |
BER_SD |
ODUk—signal degrade—TCM1 |
BER_SF |
ODUk—signal failure—TCM1 |
LOF |
OTUk—loss of frame |
UNIDENTIFIED |
TCI 2 clock failure |
UNIDENTIFIED |
Audit log 80 percent full |
UNIDENTIFIED |
Module communication failure |
UNIDENTIFIED |
Need to save running config |
UNIDENTIFIED |
Audit log 100 percent full; oldest records will be lost |
UNIDENTIFIED |
Standby database out of sync |
EQPT |
Redundant power capability lost |
EQPT |
Equipment wavelength mismatch |
UNIDENTIFIED |
DSP communication failure |
UNIDENTIFIED |
DSP failure |
UNIDENTIFIED |
Loss of channel |
UNIDENTIFIED |
FEC mismatch |
UNIDENTIFIED |
Optical power degrade low |
UNIDENTIFIED |
Optical power degrade high |
SECURITY_VIOLATION |
Security intrusion attempt detected—see audit log |
SECURITY_VIOLATION |
Security intrusion attempt detected—see audit log |
UNIDENTIFIED |
Variable optical attenuator degrade low |
UNIDENTIFIED |
Variable optical attenuator degrade high |
UNIDENTIFIED |
Variable optical attenuator failure low |
UNIDENTIFIED |
Variable optical attenuator failure high |
UNIDENTIFIED |
Laser bias degrade |
UNIDENTIFIED |
Laser bias failure |
UNIDENTIFIED |
Laser temperature degrade |
UNIDENTIFIED |
Optical amplifier gain degrade low |
UNIDENTIFIED |
Optical amplifier gain degrade high |
UNIDENTIFIED |
Optical amplifier gain failure low |
UNIDENTIFIED |
Optical amplifier gain failure high |
UNIDENTIFIED |
Laser auto power reduction |
UNIDENTIFIED |
Case temperature degrade |
UNIDENTIFIED |
Fiber temperature degrade |
UNIDENTIFIED |
Shutter open |
UNIDENTIFIED |
AWG temperature degrade |
UNIDENTIFIED |
AWG temperature failure |
UNIDENTIFIED |
AWG over temperature |
UNIDENTIFIED |
Shutter insertion loss variation degrade low |
UNIDENTIFIED |
Shutter insertion loss variation degrade high |
UNIDENTIFIED |
AWG warm up |
UNIDENTIFIED |
Plug-in module communication failure |
UNIDENTIFIED |
Optical amplifier initialization |
UNIDENTIFIED |
Optical channel connection failure |
UNIDENTIFIED |
Optical channel activation failure |
UNIDENTIFIED |
Optical channel deactivation failure |
UNIDENTIFIED |
Network topology incomplete |
UNIDENTIFIED |
Optical network type mismatch |
UNIDENTIFIED |
Automatic power control failure |
UNIDENTIFIED |
Automatic power control disabled |
UNIDENTIFIED |
Ring ID mismatch |
TIM |
TIM section monitor—trace identifier mismatch failure |
UNIDENTIFIED |
Optical channel incomplete |
UNIDENTIFIED |
Enhanced remote failure indication—path—server |
UNIDENTIFIED |
Enhanced remote failure indication—path—connectivity |
UNIDENTIFIED |
Enhanced remote failure indication—path—payload |
UNIDENTIFIED |
Automatic laser shutdown |
UNIDENTIFIED |
Firewall has been disabled |
UNIDENTIFIED |
Optical power failure low |
UNIDENTIFIED |
Optical power failure high |
EQPT |
Battery failure |
EQPT |
Extreme high voltage |
EQPT |
Extreme low voltage |
UNIDENTIFIED |
High voltage |
UNIDENTIFIED |
Low voltage |
UNIDENTIFIED |
Connection equipment mismatch |
UNIDENTIFIED |
Disable inactive user |
UNIDENTIFIED |
Disable inactive user |
UNIDENTIFIED |
Suspend user |
UNIDENTIFIED |
Suspend user clear |
UNIDENTIFIED |
Line DCC termination failure |
UNIDENTIFIED |
Multiplex section DCC termination failure |
UNIDENTIFIED |
Gigabit Ethernet out of sync |
AIS |
Alarm indication signal in Tx |
AIS |
Remote alarm indication in Tx |
LOF |
Loss of frame in Tx |
LOS |
Incoming signal loss on fibre channel interface |
UNIDENTIFIED |
Incoming synchronization loss on fibre channel interface |
UNIDENTIFIED |
Out of frame detected by GFP receiver |
UNIDENTIFIED |
Client signal loss frames detected by GFP receiver |
UNIDENTIFIED |
Client synchronization loss frames detected by GFP receiver |
UNIDENTIFIED |
Sequence mismatch |
UNIDENTIFIED |
Loss of alignment |
UNIDENTIFIED |
Out of use—administrative command |
UNIDENTIFIED |
Out of use—transport failure |
UNIDENTIFIED |
VCAT group down |
UNIDENTIFIED |
VCAT group degraded |
UNIDENTIFIED |
VCAT group incomplete |
UNIDENTIFIED |
K byte channel failure |
UNIDENTIFIED |
Industrial high temperature |
FOP_APS |
APS invalid mode |
UNIDENTIFIED |
IP address already in use within the same DCC area |
UNIDENTIFIED |
Node name already in use within the same DCC area |
UNIDENTIFIED |
Rear panel Ethernet link removed |
UNIDENTIFIED |
Manual switch to protect resulted in no traffic switch |
UNIDENTIFIED |
Manual switch back to working resulted in no traffic switch |
UNIDENTIFIED |
Forced switch to protection resulted in no traffic switch |
UNIDENTIFIED |
Forced switch back to working resulted in no traffic switch |
LOS |
Incoming payload signal absent |
UNIDENTIFIED |
Incoming overhead signal absent |
UNIDENTIFIED |
Optical safety remote interlock on |
UNIDENTIFIED |
OSPF hello fail |
UNIDENTIFIED |
Automatic power control correction skipped |
UNIDENTIFIED |
Plug-in module range settings mismatch |
UNIDENTIFIED |
APC cannot set value due to range limits |
UNIDENTIFIED |
Automatic WDM ANS finished |
UNIDENTIFIED |
Port failure |
UNIDENTIFIED |
Unreachable port target power |
UNIDENTIFIED |
Port add power degrade low |
UNIDENTIFIED |
Port add power degrade high |
UNIDENTIFIED |
Port add power fail low |
UNIDENTIFIED |
Port add power fail high |
UNIDENTIFIED |
Equipment power failure at connector A |
UNIDENTIFIED |
Equipment power failure at connector B |
UNIDENTIFIED |
Equipment power failure at return connector A |
UNIDENTIFIED |
Far-end manual switch back to working—span |
UNIDENTIFIED |
Far-end forced switch back to working—span |
UNIDENTIFIED |
Universal transponder module hardware failure |
UNIDENTIFIED |
Universal transponder module communication failure |
UNIDENTIFIED |
Automatic power control terminated on manual request |
UNIDENTIFIED |
Fibre channel distance extension credit starvation |
PLM |
GFP user payload mismatch |
UNIDENTIFIED |
GFP fibre channel distance extension mismatch |
UNIDENTIFIED |
GFP fibre channel distance extension buffer starvation |
BER_SF |
GFP client signal fail detected |
LOF |
GFP loss of frame delineation |
UNIDENTIFIED |
GFP extension header mismatch |
UNIDENTIFIED |
Signal loss on data interface |
UNIDENTIFIED |
Encapsulation mismatch—path |
UNIDENTIFIED |
Encapsulation mismatch—VT |
UNIDENTIFIED |
Encapsulation mismatch high order—path |
UNIDENTIFIED |
Encapsulation mismatch low order—path |
UNIDENTIFIED |
Synchronization loss on data interface |
AIS |
ODUk-1...4—alarm indication signal |
UNIDENTIFIED |
LCAS control word CRC check failure |
UNIDENTIFIED |
Duplicate serial number detected on a pluggable entity |
UNIDENTIFIED |
LCAS VCG member Tx side in DNU state |
UNIDENTIFIED |
LCAS VCG member Tx side in ADD state |
UNIDENTIFIED |
LCAS VCG member Rx side in FAIL state |
UNIDENTIFIED |
Optimized 1+1 APS primary facility |
UNIDENTIFIED |
Optimized 1+1 APS primary section mismatch |
UNIDENTIFIED |
Optimized 1+1 APS invalid primary section |
UNIDENTIFIED |
Composite clock high line voltage |
BER_SD |
BER threshold exceeded for signal degrade—VT |
BER_SF |
BER threshold exceeded for signal failure—VT |
UNIDENTIFIED |
Alarms suppressed on out-of-group VCAT member |
UNIDENTIFIED |
Span length out of range |
UNIDENTIFIED |
Temperature reading mismatch between SC cards |
UNIDENTIFIED |
Voltage reading mismatch between SC cards |
TIM |
VT path trace identifier mismatch |
UNIDENTIFIED |
BLSR software version mismatch |
UNIDENTIFIED |
Bridge and roll occurred |
UNIDENTIFIED |
Bridge and roll is pending a valid signal |
TIM |
Open I/O slot(s) |
UNIDENTIFIED |
ISIS adjacency failure |
SECURITY_VIOLATION |
Session time limit expired |
SECURITY_VIOLATION |
User password change required |
SECURITY_VIOLATION |
Remote authentication fail |
TIM |
Section trace identifier mismatch |
TIM |
Regenerator section trace identifier mismatch |
UNIDENTIFIED |
Switching matrix module failure—working |
UNIDENTIFIED |
Switching matrix module failure—protect |
UNIDENTIFIED |
Provisioning mismatch |
UNIDENTIFIED |
Slot communication disabled |
UNIDENTIFIED |
MSSP software version mismatch |
UNIDENTIFIED |
Archival of audit log failed |
UNIDENTIFIED |
RPR wrapped |
UNIDENTIFIED |
Software mismatch |
UNIDENTIFIED |
Link layer keepalive failure |
UNIDENTIFIED |
Bad packet count exceeds threshold |
UNIDENTIFIED |
Autonegotiation remote failure indication |
UNIDENTIFIED |
Shelf communication failure |
UNIDENTIFIED |
Duplicated shelf identifier |
UNIDENTIFIED |
Ring is squelching STS traffic |
UNIDENTIFIED |
Ring is squelching VT traffic |
UNIDENTIFIED |
Clock bus failure—shelf controller A |
UNIDENTIFIED |
Clock bus failure—shelf controller B |
UNIDENTIFIED |
Loss of clock from mate shelf controller |
UNIDENTIFIED |
Payload missing indication |
UNIDENTIFIED |
Forward defect indication |
UNIDENTIFIED |
Optical termination incomplete |
UNIDENTIFIED |
Span loss not checked |
UNIDENTIFIED |
Ring is squelching higher order traffic |
UNIDENTIFIED |
Ring is squelching lower order traffic |
UNIDENTIFIED |
Trail signal fail |
UNIDENTIFIED |
DS1 loopback command sent to far end |
UNIDENTIFIED |
Multiplex section—signal degraded |
UNIDENTIFIED |
Multiplex section—excessive errors |
UNIDENTIFIED |
High-order path—signal degraded |
UNIDENTIFIED |
High-order path—excessive errors |
UNIDENTIFIED |
Low-order path—signal degraded |
UNIDENTIFIED |
Low-order path—excessive errors |
UNIDENTIFIED |
Regenerator section—DCC termination failure |
UNIDENTIFIED |
Network memory pool low |
UNIDENTIFIED |
OSPF routing table overflow |
UNIDENTIFIED |
Auto laser shutdown disabled |
UNIDENTIFIED |
RPR protection is active |
UNIDENTIFIED |
Max RPR station number exceeded |
UNIDENTIFIED |
RPR protection configuration mismatched |
UNIDENTIFIED |
Reserved bandwidth link rate exceeded on ringlet [0|1] |
UNIDENTIFIED |
RPR interface in pass-through mode |
UNIDENTIFIED |
RPR peer node is missing |
UNIDENTIFIED |
RPR RI failure |
UNIDENTIFIED |
RPR signal failure |
UNIDENTIFIED |
RPR signal degrade |
UNIDENTIFIED |
RPR span mismatch |
UNIDENTIFIED |
LMP failure |
UNIDENTIFIED |
LMP signal degrade |
UNIDENTIFIED |
LMP signal failure |
UNIDENTIFIED |
LMP unallocated data link |
UNIDENTIFIED |
APC wrong gain setpoint |
EQPT |
Non-Cisco PPM inserted |
EQPT |
Unqualified PPM inserted |
UNIDENTIFIED |
Fast automatic protection switching |
UNIDENTIFIED |
Fast automatic protection switching config mismatch |
UNIDENTIFIED |
ADM peer cards interlink failure |
EQPT |
Fan tray mismatch |
UNIDENTIFIED |
Fibre channel distance extension function not established |
UNIDENTIFIED |
LCAS sink group error |
UNIDENTIFIED |
LCAS VCG member Rx side in DNU state |
UNIDENTIFIED |
Card/ports unable to provide protection |
UNIDENTIFIED |
TCC front port link loss |
UNIDENTIFIED |
Shutter insertion loss variation degrade low |
UNIDENTIFIED |
Shutter insertion loss variation degrade high |
UNIDENTIFIED |
Idle signal condition |
UNIDENTIFIED |
Idle signal condition in TX |
UNIDENTIFIED |
Automatic power control correction skipped |
UNIDENTIFIED |
Port add power fail low |
UNIDENTIFIED |
Port add power fail high |
UNIDENTIFIED |
Span length out of range |
UNIDENTIFIED |
Port add power degrade low |
UNIDENTIFIED |
Port add power degrade high |
UNIDENTIFIED |
DCU loss failure |
UNIDENTIFIED |
OCHNC maintenance |
UNIDENTIFIED |
K-byte channel failure |
UNIDENTIFIED |
PRP protection configuration mismatched |
UNIDENTIFIED |
Reserved bandwidth link rate exceeded on ring Let0 |
UNIDENTIFIED |
Reserved bandwidth link rate exceeded on ring Let1 |
UNIDENTIFIED |
Security invalid login—locked out |
UNIDENTIFIED |
Security invalid login—already logged on |
UNIDENTIFIED |
Syslog messages |
UNIDENTIFIED |
Configuration events |
UNIDENTIFIED |
Link up/link down trap |
UNIDENTIFIED |
Cold/warm start trap |
UNIDENTIFIED |
Authentication failure notification |
EQPT |
Unqualified PPM inserted |
UNIDENTIFIED |
Fast automatic protection switching |
UNIDENTIFIED |
Fast automatic protection switching config mismatch |
UNIDENTIFIED |
ADM peer cards interlink failure |
EQPT |
Fan tray mismatch |
UNIDENTIFIED |
Fibre channel distance extension function not established |
UNIDENTIFIED |
LCAS sink group error |
UNIDENTIFIED |
LCAS VCG member Rx side in DNU state |
UNIDENTIFIED |
Card/ports unable to provide protection |
UNIDENTIFIED |
TCC front port link loss |
UNIDENTIFIED |
Shutter insertion loss variation degrade low |
UNIDENTIFIED |
Shutter insertion loss variation degrade high |
UNIDENTIFIED |
Idle signal condition |
UNIDENTIFIED |
Idle signal condition in TX |
UNIDENTIFIED |
Automatic power control correction skipped |
UNIDENTIFIED |
Port add power fail low |
UNIDENTIFIED |
Port add power fail high |
UNIDENTIFIED |
DCU loss failure |
UNIDENTIFIED |
OCHNC maintenance |
UNIDENTIFIED |
K-byte channel failure |
UNIDENTIFIED |
PRP protection configuration mismatched |
UNIDENTIFIED |
Reserved bandwidth link rate exceeded on ring Let0 |
UNIDENTIFIED |
Reserved bandwidth link rate exceeded on ring Let1 |
UNIDENTIFIED |
Security invalid login—locked out |
UNIDENTIFIED |
Security invalid login—already logged on |
UNIDENTIFIED |
Syslog messages |
UNIDENTIFIED |
Configuration events |
UNIDENTIFIED |
Link up/link down trap |
UNIDENTIFIED |
Cold/warm start trap |
UNIDENTIFIED |
Authentication failure notification |
UNIDENTIFIED |
Alarm indication signal in TX—customer installation |
UNIDENTIFIED |
Remote alarm indication in TX—customer installation |