- Chapter 1: Introduction
- Chapter 2: Basic Concept
- Chapter 3: Building the Network
- Chapter 4: Maintaining an Efficient Network
- Chapter 5: Configuring Hardware
- Chapter 6: Provisioning Cards
- Chapter 7: Provisioning Services and Connections
- Chapter 8: Managing Security
- Chapter 9: Managing Faults
- Chapter 10: Managing Performance
- Chapter 11: Managing Inventory
- Chapter 12: Managing Southbound and Northbound Interfaces
- Chapter 13: Configuring MPLS-TP Using the CPT System
- Appendix A: Icons and Menus Displayed in Prime Optical
- Appendix B: NE Explorer Information
- Appendix C: Slot Property Information-Common, DWDM, Electrical, and Ethernet Cards
- Appendix D: Slot Property Information FC_MR-4, FMEC, Multirate and Optical Cards
- Appendix E: Performance Data
- Appendix F: Error Messages
- Appendix G: Troubleshooting
- Appendix H: ML Provisioning Methodology
Cisco Prime Optical User Guide, 10.7
Bias-Free Language
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
- Updated:
- June 18, 2018
Chapter: Appendix E: Performance Data
- ONS 15305-Specific PM Tables
- PM Tables for CTC-Based NEs
- 8B10B PM Table—ONS 15454 SONET, ONS 15454 SDH
- ESCON PM Table—ONS 15454 SONET, ONS 15454 SDH
- CoS PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH
- DS1 PM Table (Far End)
- DS1 PM Table
- DS3 PM Table
- DS3 and DS3I PM Table (Far End)—ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH
- E1 PM Table—ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH
- E1 PM Table (Far End)—ONS 15310 MA SDH, ONS 15454 SONET, and ONS15454 SDH
- E3 PM Table—ONS 15310 MA SDH, ONS 15454 SDH
- CE-Series Ethernet PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH
- E-Series Ethernet PM Table—ONS 15327, ONS 15454 SONET, ONS 15454 SDH
- G-Series Ethernet PM Table—ONS 15327, ONS 15454 SONET, ONS 15454 SDH
- ML-Series Ethernet PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH
- ASAP-Series Ethernet PM Table—ONS 15600 SONET, ONS 15600 SDH
- DWDM-Series Ethernet PM Table—ONS 15454 SONET, ONS 15454 SDH
- CPT-Series Ethernet PM Table—ONS 15454 SONET, ONS 15454 SDH
- GFP PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, ONS 15454 SDH, and ONS 15600 SDH
- LEX PM Table—ONS 15454 SONET, ONS 15454 SDH
- High Order PM Table (Far End)—ONS 15310 MA SDH, ONS 15454 SDH
- High Order PM Table (Far End)—ONS 15600 SDH
- High Order PM Table—ONS 15310 MA SDH, ONS 15454 SDH
- High Order PM Table—ONS 15600 SDH
- IP SLA PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH
- Low Order VC11 PM Table—ONS 15454 SDH
- Low Order VC12 PM Table—ONS 15310 MA SDH, ONS 15454 SDH
- Low Order VC11 Section PM Table (Far End)—ONS 15454 SDH
- Low Order VC12 Section PM Table (Far End)—ONS 15310 MA SDH, ONS15454 SDH
- Low Order VC3 PM Table—ONS 15310 MA SDH, ONS 15454 SDH
- Low Order VC3 Section PM Table (Far End)—ONS 15310 MA SDH and ONS 15454 SDH
- Multiplex Section PM Table (Far End)—ONS 15310 MA SDH, ONS 15454 SDH
- Multiplex Section PM Table (Far End)—ONS 15600 SDH
- Multiplex Section PM Table (Near End)—ONS 15310 MA SDH, ONS 15454 SDH
- Multiplex Section PM Table—ONS 15600 SDH
- Optical Physical PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS15310 MA SDH, ONS15454 SONET, ONS 15454 SDH, ONS 15600 SONET, and ONS 15600 SDH
- OTN Encryption Table—ONS 15454 SONET, ONS 15454 SDH
- OTN FEC PM Table—ONS 15454 SONET, ONS 15454 SDH
- OTN Path PM Table (Far End)—ONS 15454 SONET, ONS 15454 SDH
- OTN Path PM Table (Near End)—ONS 15454 SONET, ONS 15454 SDH
- OTN Section PM Table (Far End)—ONS 15454 SONET, ONS 15454 SDH
- OTN Section PM Table (Near End)—ONS 15454 SONET, ONS 15454 SDH
- POS PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15454 SONET, ONS 15310 MA SDH, ONS 15454 SDH, ONS 15600 SONET, ONS 15600 SDH
- Regenerator Section PM Table—ONS 15310 MA SDH, ONS 15454 SDH
- Regenerator Section PM Table—ONS 15600 SDH
- RPR 802.17 PM Table—ONS 15454 SONET, ONS 15454 SDH
- FC PM Table—ONS 15454 SONET, ONS 15454 SDH
- ISC PM Table—ONS 15454 SONET, ONS 15454 SDH
- SONET Line PM Table (Far End)—ONS 15310 CL, ONS 15310 MA SONET, ONS 15327, ONS 15454 SONET, ONS 15600 SONET
- SONET Line PM Table (Near End)—ONS 15310 CL, ONS 15310 MA SONET, ONS 15327, ONS 15454 SONET, ONS 15600 SONET
- SONET Section PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15327, ONS 15454 SONET, ONS 15600 SONET
- SONET STS Path PM Table (Far End)—ONS 15310 CL, ONS 15310 MA SONET, ONS 15327, ONS 15454 SONET, ONS 15600
- SONET STS Path PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15327, ONS 15454 SONET, ONS 15600 SONET
- SONET VT1.5 PM Table
- SONET VT2 PM Table
- SONET VT PM Table (Far End)—ONS 15310 CL, ONS 15310 MA SONET, ONS15327, ONS 15454 SONET
- SONET VT2 PM Table (Far End)—ONS 15454 SONET
Performance Data
This topic describes the performance management (PM) tables that are available in Cisco Prime Optical and includes the following sections:
Note
PM data collection is not available for the ONS 15216.
ONS 15305-Specific PM Tables
This section describes the PM tables that are specific to ONS 15305 NEs.
Overview of Supported PM Parameters
ONS 15305 PM parameters are available on any of the following cards:
Edge SDH
Table E-1 to Table E-7 list all the ONS 15305 Edge SDH PM parameters with the corresponding description and a list of cards supported.
|
|
|
|
|---|---|---|
| S1.1-2-LC, S1.1-8-LC, S4.1-2-LC, S4.1-4-LC, S16.1-1-LC, L4.2-2-LC, L16.2-1LC, S1.1-2-LC/E1-21 |
||
|
|
|
|
|---|---|---|
| S1.1-2-LC, S1.1-8-LC, S4.1-2-LC, S4.1-4-LC, S16.1-1-LC, L4.2-2-LC, L16.2-1LC, S1.1-2-LC/E1-21 |
||
|
|
|
|
|---|---|---|
| S1.1-2-LC, S1.1-8-LC, S4.1-2-LC, S4.1-4-LC, S16.1-1-LC, L4.2-2-LC, L16.2-1LC, S1.1-2-LC/E1-21 |
||
|
|
|
|
|---|---|---|
| S1.1-8-LC, E3T3-6(3), E1-8(1), E1-21(1), E1-63(1), S1.1-2-LC/E1-21(1) |
||
|
|
|
|
|---|---|---|
| S1.1-8-LC, E3T3-6(3), E1-8(1), E1-21(1), E1-63(1), S1.1-2-LC/E1-21(1) |
||
E.0.0.1 Edge Statistics
Table E-8 lists all the ONS 15305 PM parameters with the corresponding description and a list of cards supported.
Edge Statistics DCC PM Table
The Edge Statistics DCC PM table shows 15-minute and 1-day data communications channel (DCC) edge statistics performance data for the ONS 15305. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-9 describes the fields in the Edge Statistics DCC PM table.
Edge Statistics LAN PM Table
The Edge Statistics LAN PM table shows 15-minute and 1-day LAN edge statistics performance data for the ONS 15305. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-10 describes the fields in the Edge Statistics LAN PM table.
Edge Statistics WAN PM Table
The Edge Statistics WAN PM table shows 15-minute and 1-day WAN edge statistics performance data for the ONS 15305. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-11 describes the fields in the Edge Statistics WAN PM table.
Edge SDH High Order VC PM Table
The Edge SDH High Order VC PM table shows near- and far-end 15-minute and 1-day SDH high-order Virtual Container (VC) performance data for the ONS 15305. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-12 describes the fields in the Edge SDH High Order VC PM table.
Edge SDH Low Order VC PM Table
The Edge SDH Low Order VC PM table shows near- and far-end 15-minute and 1-day SDH low-order VC performance data for the ONS 15305. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-13 describes the fields in the Edge SDH Low Order VC PM table.
Edge SDH Multiplex Section PM Table
The Edge SDH Multiplex Section PM table shows near- and far-end 15-minute and 1-day SDH multiplex section performance data for the ONS 15305. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-14 describes the fields in the Edge SDH Multiplex Section PM table.
Edge SDH Regenerator Section PM Table
The Edge SDH Regenerator Section PM table shows 15-minute and 1-day SDH regenerator section performance data for the ONS 15305. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-15 describes the fields in the Edge SDH Regenerator Section PM table.
PM Tables for CTC-Based NEs
This section describes the PM tables that are specific to the CTC-based NEs: ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MS SDH, ONS 15327, ONS 15454 SONET, ONS 15454 SDH, ONS 15600 SONET, and ONS 15600 SDH.
Note Performance management for the CTC-based ONS 15305 R3.0 is similar to the performance management for the non-CTC-based ONS 15305. See ONS 15305-Specific PM Tables.
For CTC-based NEs, each 15-minute or 1-day PM table has a corresponding real-time PM table that allows you to examine the current value of a PM parameter in granularities finer than 15 minutes or 1 day. Not all of the fields in the historical PM tables are shown in the real-time PM tables. The first fields in real-time PM tables are NE ID, Module Name, Physical Location, Interface, Time Stamp, and Validity; the remaining fields are the actual real-time attributes being polled. The Validity column indicates whether the data in the entry is valid: “true” indicates that the entry is valid; “false” indicates that the entry is invalid.
The following conventions apply to PM tables for CTC-based NEs:
- Invalidity in the historical PM table is shown with the corresponding table cell rendered in italics and marked with an asterisk (*).
Note Real-time PM tables do not support invalidity coloring.
- Threshold crossing alerts (TCAs) for a specific statistic in a particular row in the historical PM table are indicated with a purple rendering for the corresponding cell.
Note Real-time PM tables do not support TCAs.
- Fields that are not applicable for a particular module in a given PM table are indicated by displaying N/A (not applicable) in the corresponding table cell.
- 1-day PM data is collected at 00:00 hours Greenwich Mean Time (GMT) (time on the Prime Optical server host).
- For release 4.0 and later NEs, PM data collected for cards that are preprovisioned and not physically present on a slot are indicated by the symbol ENEQ displayed for the corresponding table cell.
Note For an RTPM query for remote NEs, select the slot number and port number required for a PM query (do not select slot All and port All).
Note The PM parameters that Prime Optical supports for CTC-based NEs are also supported by Prime Optical GateWay/CORBA.
8B10B PM Table—ONS 15454 SONET, ONS 15454 SDH
The 8B10B PM table shows performance data for ONS 15454 SONET and ONS 15454 SDH DWDM cards that support Fibre Channel (FC) or Gigabit Ethernet payloads. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-16 describes the fields in the 8B10B PM table.
ESCON PM Table—ONS 15454 SONET, ONS 15454 SDH
The ESCON PM table shows performance data for ONS 15454 SONET and ONS 15454 SDH DWDM cards that support ESCON payload. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-17 describes the fields in the ESCON PM table.
CoS PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH
The CoS PM table shows Class of Service (CoS) performance data for the ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH ML-series cards. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-18 describes the fields in the CoS PM table.
DS1 PM Table (Far End)
The DS1 PM table shows far-end DS-1 performance data. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-19 describes the fields in the DS1 PM table.
DS1 PM Table
The DS1 PM table contains PM information at the line layer. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-20 describes the fields in the DS1 PM table.
DS3 PM Table
The DS3 PM table contains PM information at the DS-3 layer. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-21 describes the fields in the DS3 PM table.
DS3 and DS3I PM Table (Far End)—ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH
The DS3 and DS3I PM table shows far-end performance data for the DS-3 and DS3I cards. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-22 describes the fields in the DS3 and DS3I PM table.
E1 PM Table—ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH
The E1 PM table shows performance data for the following cards:
You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-23 describes the fields in the E1 PM table.
E1 PM Table (Far End)—ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH
The E1 PM table shows far-end performance data for the following cards:
- ONS 15310 MA SDH: E1_21_E3_DS3_3 and E1_63_E3_DS3_3
- ONS 15454 SONET: DS1_E1_56
- ONS 15454 SDH: E1, E1N, and E1_42 cards.
You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-24 describes the fields in the E1 PM table.
E3 PM Table—ONS 15310 MA SDH, ONS 15454 SDH
The E3 PM table shows performance data for the ONS 15310 MA SDH E1_21_E3_DS3_3 and E1_63_E3_DS3_3 cards and the ONS 15454 SDH E3 card. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-25 describes the fields in the E3 PM table.
CE-Series Ethernet PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH
The CE-Series Ethernet PM table shows performance data for the ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH CE-series Ethernet cards. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-26 describes the fields in the CE-Series Ethernet PM table.
Note Real-time PM data is not available for Ethernet cards on NE releases earlier than release 5.0.
E-Series Ethernet PM Table—ONS 15327, ONS 15454 SONET, ONS 15454 SDH
The E-Series Ethernet PM table shows performance data for the ONS 15327, ONS 15454 SONET, and ONS 15454 SDH E-series Ethernet cards. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-27 describes the fields in the E-Series Ethernet PM table.
Note Real-time PM data is not available for Ethernet cards on NE releases earlier than release 5.0.
G-Series Ethernet PM Table—ONS 15327, ONS 15454 SONET, ONS 15454 SDH
The G-Series Ethernet PM table shows performance data for the ONS 15327, ONS 15454 SONET, and ONS 15454 SDH G-series Ethernet cards. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-28 describes the fields in the G-Series Ethernet PM table.
Note Real-time PM data is not available for Ethernet cards on NE releases earlier than release 5.0.
ML-Series Ethernet PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH
The ML-Series Ethernet PM table shows performance data for the ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH ML-series Ethernet cards. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-29 describes the fields in the ML-Series Ethernet PM table.
Note Real-time PM data is not available for Ethernet cards on NE releases earlier than release 5.0.
ASAP-Series Ethernet PM Table—ONS 15600 SONET, ONS 15600 SDH
The ASAP-Series Ethernet PM table shows performance data for the ONS 15600 SONET and ONS 15600 SDH ASAP-series Ethernet cards. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-30 describes the fields in the ASAP-Series Ethernet PM table.
Note Real-time PM data is not available for Ethernet cards on NE releases earlier than release 5.0.
DWDM-Series Ethernet PM Table—ONS 15454 SONET, ONS 15454 SDH
The DWDM-Series Ethernet PM table shows performance data for the ONS 15454 SONET and ONS 15454 SDH DWDM-series Ethernet cards. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-31 describes the fields in the DWDM-Series Ethernet PM table.
Note Real-time PM data is not available for Ethernet cards on NE releases earlier than release 5.0.
CPT-Series Ethernet PM Table—ONS 15454 SONET, ONS 15454 SDH
The CPT-Series Ethernet PM table shows performance data for the ONS 15454 SONET and ONS 15454 SDH CPT-series Ethernet cards. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-32 describes the fields in the CPT-Series Ethernet PM table.
Note Real-time PM data is not available for Ethernet cards on NE releases earlier than release 5.0.
GFP PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, ONS 15454 SDH, and ONS 15600 SDH
The GFP PM table provides monitoring capability to allow operators to identify performance degradation in the generic framing procedure (GFP) multiplexing and framing. GFP describes a framing and encapsulation format for transporting L2/L3 data over SONET, SDH, or OTN transport networks.
You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-33 describes the fields in the GFP PM table.
LEX PM Table—ONS 15454 SONET, ONS 15454 SDH
The LEX PM table provides monitoring of performance parameters related to HDLC particular framing (LEX) on optical interfaces. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Note LEX monitors performance parameters only on ADM-10G cards.
Table E-34 describes the fields in the LEX PM table.
High Order PM Table (Far End)—ONS 15310 MA SDH, ONS 15454 SDH
The SDH High Order PM table shows far-end performance data for the far-end ONS 15310 MA SDH and ONS 15454 SDH high-order sections. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-35 describes the fields in the High Order PM table.
High Order PM Table (Far End)—ONS 15600 SDH
The High Order PM table shows far-end performance data for the ONS 15600 SDH high-order section. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-36 describes the fields in the High Order PM table.
High Order PM Table—ONS 15310 MA SDH, ONS 15454 SDH
The High Order PM table shows performance data for the ONS 15310 MA SDH and ONS 15454 SDH physical sections. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-37 describes the fields in the High Order PM table.
High Order PM Table—ONS 15600 SDH
The High Order PM table shows performance data for the ONS 15600 SDH physical section. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-38 describes the fields in the High Order PM table.
IP SLA PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, and ONS 15454 SDH
The IP SLA PM table allows you to monitor service-level agreements (SLAs) for IP networks. Service levels are measured by downtime, bandwidth, latency, jitter, packet loss, and so on. These measurements are controllable and do not depend on network traffic.
You can display IP SLA performance data in real time. When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The IP SLA feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Note ● You can launch the IP SLA PM table only from the IP SLA table, not from the Domain Explorer or the NE Explorer.
- Performance monitoring is disabled for the IP SLA echo operation. If you select an echo row in the IP SLA PM table, the Performance menu is disabled.
Table E-39 describes the fields in the IP SLA PM table.
Low Order VC11 PM Table—ONS 15454 SDH
The Low Order VC11 PM table shows performance data for the ONS 15454 SDH low-order VC11. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-40 describes the fields in the Low Order VC11 PM table.
Low Order VC12 PM Table—ONS 15310 MA SDH, ONS 15454 SDH
The Low Order VC12 PM table shows performance data for the ONS 15310 MA SDH and ONS 15454 SDH low-order VC12. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-41 describes the fields in the Low Order VC12 PM table.
Low Order VC11 Section PM Table (Far End)—ONS 15454 SDH
The Low Order VC11 Section PM table shows far-end performance data for the ONS 15454 SDH low-order VC11 section far end. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-42 describes the fields in the Low Order VC11 Section PM table.
Low Order VC12 Section PM Table (Far End)—ONS 15310 MA SDH, ONS 15454 SDH
The Low Order VC12 Section PM table shows far-end performance data for the ONS 15310 MA SDH and ONS 15454 SDH low-order VC12 section far end. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-43 describes the fields in the Low Order VC12 Section PM table.
Low Order VC3 PM Table—ONS 15310 MA SDH, ONS 15454 SDH
The Low Order VC3 PM table shows performance data for the ONS 15310 MA SDH and ONS 15454 SDH low-order VC3. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-44 describes the fields in the Low Order VC3 PM table.
Low Order VC3 Section PM Table (Far End)—ONS 15310 MA SDH and ONS 15454 SDH
The Low Order VC3 Section PM table shows far-end performance data for the far-end ONS 15310 MA SDH and ONS 15454 SDH low-order VC3 sections. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-45 describes the fields in the Low Order VC3 Section PM table.
Multiplex Section PM Table (Far End)—ONS 15310 MA SDH, ONS 15454 SDH
The Multiplex Section PM table shows far-end performance data for the ONS 15310 MA SDH and ONS 15454 SDH multiplex sections (far-end). You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-46 describes the fields in the Multiplex Section PM table.
Multiplex Section PM Table (Far End)—ONS 15600 SDH
The Multiplex Section PM table shows far-end performance data for the ONS 15600 SDH multiplex section far end. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-47 describes the fields in the Multiplex Section PM table.
Multiplex Section PM Table (Near End)—ONS 15310 MA SDH, ONS 15454 SDH
The Multiplex Section PM table shows performance data for the ONS 15310 MA SDH and ONS 15454 SDH multiplex sections. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-48 describes the fields in the Multiplex Section PM table.
Multiplex Section PM Table—ONS 15600 SDH
The Multiplex Section PM table shows performance data for the ONS 15600 SDH multiplex section. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-49 describes the fields in the Multiplex Section PM table.
Optical Physical PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15310 MA SDH, ONS 15454 SONET, ONS 15454 SDH, ONS 15600 SONET, and ONS 15600 SDH
The Optical Physical PM table shows physical-layer performance data. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Optical Service Channel (OSC) power—New optical power parameters are monitored for optical cards. Six new PM parameters are added to all the optical interfaces of all the supported cards for ONS 15454 SONET and ONS 15454 SDH. Using Prime Optical, you can monitor six new parameters for optical power: three each for received and transmitted power.
You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-50 describes the fields in the Optical Physical PM table.
OTN Encryption Table—ONS 15454 SONET, ONS 15454 SDH
The OTN Encryption table shows OTN forward error correction (FEC) performance data for trunk ports on the ONS 15454 SONET and ONS 15454 SDH. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-51 describes the fields in the OTN Encryption table.
OTN FEC PM Table—ONS 15454 SONET, ONS 15454 SDH
The OTN FEC PM table shows OTN forward error correction (FEC) performance data for trunk ports on the ONS 15454 SONET and ONS 15454 SDH. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-52 describes the fields in the OTN FEC PM table.
OTN Path PM Table (Far End)—ONS 15454 SONET, ONS 15454 SDH
The OTN Path PM table shows OTN path performance data for trunk ports on the ONS 15454 SONET and ONS 15454 SDH. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-53 describes the fields in the OTN Path PM table.
OTN Path PM Table (Near End)—ONS 15454 SONET, ONS 15454 SDH
The OTN Path PM table shows near-end OTN path performance data for trunk ports on the ONS 15454 SONET and ONS 15454 SDH. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-54 describes the fields in the OTN Path PM table.
OTN Section PM Table (Far End)—ONS 15454 SONET, ONS 15454 SDH
The OTN Section PM table shows OTN section performance data for trunk ports on the ONS 15454 SONET and ONS 15454 SDH. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-55 describes the fields in the OTN Section PM table.
OTN Section PM Table (Near End)—ONS 15454 SONET, ONS 15454 SDH
The OTN Section PM table shows near-end OTN section performance data for trunk ports on the ONS 15454 SONET and ONS 15454 SDH. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-56 describes the fields in the OTN Section PM table.
POS PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15454 SONET, ONS 15310 MA SDH, ONS 15454 SDH, ONS 15600 SONET, ONS 15600 SDH
The POS PM table shows POS performance data for Ethernet cards. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-57 describes the fields in the POS PM table.
Note Real-time PM data is not available for POS cards on NE releases earlier than release 5.0.
Regenerator Section PM Table—ONS 15310 MA SDH, ONS 15454 SDH
The Regenerator Section PM table shows performance data for the ONS 15310 MA SDH and ONS 15454 SDH regenerator section. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-58 describes the fields in the Regenerator Section PM table.
Regenerator Section PM Table—ONS 15600 SDH
The Regenerator Section PM table shows performance data for the ONS 15600 SDH regenerator section. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-59 describes the fields in the Regenerator Section PM table.
RPR 802.17 PM Table—ONS 15454 SONET, ONS 15454 SDH
The RPR 802.17 PM table shows performance data for the ONS 15454 SONET and ONS 15454 SDH ML-series cards in Resilient Packet Ring (RPR) mode (IEEE 802.17). You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-60 describes the fields in the RPR 802.17 PM table. The fields shown depend on the RPR type selection.
FC PM Table—ONS 15454 SONET, ONS 15454 SDH
The FC PM table shows performance data for the ONS 15454 SONET and ONS 15454 SDH. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-61 describes the fields in the FC PM table.
ISC PM Table—ONS 15454 SONET, ONS 15454 SDH
The ISC PM table shows performance data for the ONS 15454 SONET and ONS 15454 SDH. You can display 15-minute or 1-day increments.
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Managing Real-Time PM Data.
Table E-62 describes the fields in the ISC PM table.
SONET Line PM Table (Far End)—ONS 15310 CL, ONS 15310 MA SONET, ONS 15327, ONS 15454 SONET, ONS 15600 SONET
The SONET Line PM table shows far-end performance data for the ONS 15310 CL, ONS 15310 MA SONET, ONS 15327, ONS 15454 SONET, and ONS 15600 SONET line. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-63 describes the fields in the SONET Line PM table.
SONET Line PM Table (Near End)—ONS 15310 CL, ONS 15310 MA SONET, ONS 15327, ONS 15454 SONET, ONS 15600 SONET
The SONET Line PM table shows near-end performance data for the ONS 15310 CL, ONS 15310 MA SONET, ONS 15327, ONS 15454 SONET, and ONS 15600 SONET line. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-64 describes the fields in the SONET Line PM table.
SONET Section PM Table—ONS 15310 CL, ONS 15310 MA SONET, ONS 15327, ONS 15454 SONET, ONS 15600 SONET
The SONET Section PM table shows performance data at the section layer. You can display performance data for 15-minute, 1-day, or real-time increments:
- 15-minute—Data is collected at the quarter-hour (for example, at 10:00, 10:15, and so on). The data shown represents the difference in counter values between successive 15-minute intervals.
- 1-day—Data is collected at midnight GMT. The data shown represents the difference between the counter values read at successive midnights.
- Real-time—When a real-time PM session is running, it polls the NE for x number of attributes every 10 to 900 seconds. The Real-time feature allows you to examine the current value of a PM parameter in granularities finer than the standard 15-minute or 1-day interval. For more information, see Managing Real-Time PM Data.
Performance monitoring can be done either on selected modules, or on specific locations in the NE. You can use the Plot tab to plot the data in a graphical view that is stored in the Prime Optical database. See Using PM Data Graphs.
Table E-65 describes the fields in the SONET Section PM table.