Table of Contents
Release Notes for Cisco Prime Infrastructure Plug and Play Gateway Patch 2.0.0.30
Plug and Play Gateway Patch Installation
Obtaining Documentation and Submitting a Service Request
Release Notes for Cisco Prime Infrastructure Plug and Play Gateway Patch 2.0.0.30
First Published: April 16, 2014
This Release Notes document contains the following sections:
Introduction
The Cisco Prime Infrastructure Plug and Play Gateway Patch 2.0.0.30 provides a resolution for the port hanging issue and also provides cns disconnection options.
System Requirements
For information on hardware requirements, see the “Prime Infrastructure Plug and Play Gateway Server Requirements” section of the Cisco Prime Infrastructure 2.0 Quick Start Guide .
The Cisco Prime Infrastructure Plug and Play Gateway 2.0.0.30 standalone server patch must be installed on the Cisco Prime Infrastructure Plug and Play Gateway Server 2.0. The system requirements are the same as that for the Cisco Prime Infrastructure 2.0 Plug and Play Gateway Server.
Installation Notes
This section contains instructions for installing the Cisco Prime Infrastructure Plug and Play Gateway.
Plug and Play Gateway Patch Installation
The Plug and Play Gateway standalone server patch is available in the pnp-gateway-patch-2.0.0.30.tar.gz file. The patch upgrade procedure requires an FTP or TFTP server containing the patch file.
You can access this server from the Cisco Prime Infrastructure 2.0 Plug and Play Gateway standalone server by following these steps:
1.
Log in to the Plug and Play Gateway standalone server as admin user. The following is a sample output of the patch upgrade with the url FTP:
2.
Use the application upgrade command to install the pnp-gateway-patch-2.0.0.30.tar.gz Plug and Play Gateway standalone patch. The following is a sample output of the pnp gateway patch upgrade:
3.
Exit from the current terminal (shell) and re-login as admin user.
4.
Execute the pnp setup command to reconfigure the Plug and Play standalone server and start the plug and play process.
![]()
Note
To enable the automatic event disconnection use the Plug and Play advanced setup option. Press ‘Y’ when prompted with “Turn down device connection after first successful configuration push (y/n)”. By default the option is set to ‘N’, which means the connection is disabled. To enable the automatic event disconnection use the Plug and Play advanced setup option. Press ‘Y’ when prompted with “Turn down device connection after first successful configuration push (y/n)”. By default the option is set to ‘N’, which means the connection is disabled.
Caveats
This section lists the open and resolved caveats for Cisco Prime Infrastructure Release 2.0.0.30:
Resolved Caveats
Symptoms: Plug and Play Gateway must provide an option to disconnect the Cisco Networking System (CNS) connection once the CNS processing is completed.
Conditions: This option must be enabled only with a single configuration.
Workaround: This issue is resolved.
Symptoms: The Plug and Play Gateway 11016 port hangs when all devices reconnect together.
Related Documentation
You can access the following additional Cisco Prime Infrastructure documentation on Cisco.com:
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation , which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as an RSS feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently supports RSS Version 2.0.
This document is to be used in conjunction with the documents listed in the “Related Documentation” section.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks . Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.