The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This guide describes the installation process using standalone installer. Cisco Prime Service Catalog comprises of two required component applications, Service Catalog and Service Link, and one optional component application called Reporting.
The installation is supported on WildFly and WebLogic application servers and can be configured in either Standalone and Cluster setup.
Subsequent sections in this chapter describes various deployment topologies for both WildFly and WebLogic Application Servers.
For information about installing the 12.0.1 Virtual Appliance (OVA file), see Cisco Prime Service Catalog Quick Start Guide .
Prime Service Catalog can be set up in a standalone or cluster mode.
– For a WebLogic Cluster environment, the topology may include multiple application server machines. The following diagram shows an example of an application server cluster with two nodes containing the Service Catalog component application, and a standalone application server containing the Service Link component application:
– For WildFly Cluster environment, the available topologies are a two VM and a four VM topology.
The following diagram shows an example of a four VM topology that has an application server cluster with two nodes containing the Service Catalog component application, one with domain controller and another node with Service Link component application.
Figure 1-3 WildFly 4 VM Topology
The following diagram shows an example of a two VM topology that has two horizontal nodes (i.e. two separate hosts) in a Wildfly cluster configuration. One node contains the Service Catalog component application, and another contains a Domain Controller, Service Link component application, and Service Catalog component application.
The user can start with 2 nodes, and add more nodes (i.e. more hosts) to the cluster as desired.
Note The Prime Service Catalog Installer will support up to 6th node for the cluster. If the user wants to add a 7th node or more, see section Adding Subsequent Host Nodes Manually in WildFly Cluster.
Figure 1-4 WildFly 2 VM Topology
Next chapter describes the software and hardware requirements for a typical deployment topology.
The following flowchart provides a high level flow of Prime Service Catalog installation.
Figure 1-5 Common Installation Steps
This section provides a road map of the installation process for Prime Service Catalog:
Step 1 Follow the instructions provided in Installation Requirements to ensure that you have adequately addressed the minimum hardware and software requirements, and installed the prerequisite software.
Step 2 Create the Service Catalog database, as described in Configuring the Service Catalog Database and complete the Database Information Worksheet. You will need this information when running the Prime Service Catalog installation wizard.
Step 3 Prepare the application server for use with Prime Service Catalog, by performing the tasks described in one of the following sections:
For WildFly, go to the Preinstallation Tasks for WildFly.
For WebLogic, go to the Preinstallation Configuration for WebLogic.
Complete the respective Application Server Information Worksheet as described in the Worksheets section. You will need this information when running the Prime Service Catalog installation wizard.
Step 4 Run the Prime Service Catalog installer on the application server machine, as described in the Installing Prime Service Catalog on WildFly Application Server or Installing Prime Service Catalog on WebLogic Application Server. If you are performing an upgrade installation from a previous release, see Upgrading Prime Service Catalog in conjunction with this section.
Step 5 Perform the post installation tasks for your application server and verify your installation as described in one of the following sections:
For WildFly, go to the Postinstallation Tasks for WildFly.
For WebLogic, go to the Postinstallation Configuration for WebLogic.
Step 6 To enable the Reporting features, you also need to install the Reporting software module and the Cognos software, and configure the Cognos Server to integrate with the Prime Service Catalog application. When you are ready to do this, follow the instructions in Installing and Upgrading Reporting Module.