Have an account?
  •   Personalized content
  •   Your products and support

Need an account?

Create an account

Special Notes and Exceptions for Devices Supported in Cisco Prime LAN Management Solution 4.2

Available Languages

Updated:November 14, 2014
Special Notes and Exceptions for Devices Supported in CiscoWorks LAN Management Solution 4.0

Special Notes and Exceptions for Devices Supported in Cisco Prime LAN Management Solution 4.2

The following table lists the special notes and exceptions for the devices supported in Cisco Prime LAN Management Solution 4.2:

Updated version of the document is available at :

http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/device_support/table/lms42sdt_specialnotes.html

For information about the supported devices in Cisco Prime LAN Management Solution 4.2 please refer to the following location:

http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/device_support/table/lms42sdt.html


IOS Devices

This table explains the specific support notes for all of the series of devices under IOS Devices family:


Cisco 12000 Series Routers
Device Name sysObjectID Special Notes
Cisco 12012 Router (GSR12/60) 1.3.6.1.4.1.9.1.173
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 12008 Router (GSR8/40) 1.3.6.1.4.1.9.1.182
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 12016 Router 1.3.6.1.4.1.9.1.273
  • SSHv2 is supported on Solaris server. SSHv1 is not supported.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Support for dual supervisor modules
Cisco 12010 Router 1.3.6.1.4.1.9.1.348
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 12416 Router 1.3.6.1.4.1.9.1.385
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 12404 Router (GSR4/80-AC) 1.3.6.1.4.1.9.1.423
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 12006 Router 1.3.6.1.4.1.9.1.590

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management

Cisco 7000 Series Routers
Device Name sysObjectID Special Notes
Cisco 7010 Router 1.3.6.1.4.1.9.1.12
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 7150-2FE Router 1.3.6.1.4.1.9.1.355
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 7150-8T Router 1.3.6.1.4.1.9.1.356
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 7150-2T3 Router 1.3.6.1.4.1.9.1.357
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco WS-SVC-SAMI-BB (WS-SVC-SAMI-BB-K9) 1.3.6.1.4.1.9.1.744
  • Software Management: Support for the module requires IP address of the parent Catalyst 6000 or 7600 device with proper Telnet credentials.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Path Analysis
    • Image Management
Cisco 7000 Router 1.3.6.1.4.1.9.1.8
  • Cisco routers supply the User Tracking application with ARP Table information.

Cisco 7200 Series Routers
Device Name sysObjectID Special Notes
Cisco 7206 Router 1.3.6.1.4.1.9.1.108
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 7204 Router 1.3.6.1.4.1.9.1.125
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 7202 Router 1.3.6.1.4.1.9.1.194
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 7206VXR Router with cevCpu7200Npeg2 and cevC7200CCPA 1.3.6.1.4.1.9.1.222
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 7204VXR Router 1.3.6.1.4.1.9.1.223
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 7201 Router (CISCO7201) 1.3.6.1.4.1.9.1.821
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • User Tracking
    • Inventory Config and Image management
    • Image Distribution using SSH

Cisco 800 Series Integrated Services Routers
Device Name sysObjectID Special Notes
Cisco 887V Integrated Services Router (CISCO887VW-GNA-K9, CISCO887VW-GNE-K9) 1.3.6.1.4.1.9.1.1040

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 888E, 888EW Integrated Services Router (CISCO888E-K9,CISCO888EW-GNA-K9,CISCO888EW-GNE-K9) 1.3.6.1.4.1.9.1.1096

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 887 Integrated Services Routers(887M) 1.3.6.1.4.1.9.1.1105

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 887V Integrated Services Router (CISCO887VG-K9, CISCO887VGW-GNA-K9, CISCO887VGW-GNE-K9) 1.3.6.1.4.1.9.1.1138

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 887V Integrated Services Router (C887VSRST-K9, C887VSRSTW-GNA-K9, C887VSRSTW-GNE-K9) 1.3.6.1.4.1.9.1.1139

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Config Management
    • Image Management
    • Basic EnergyWise Management
Cisco 801 ISDN Router 1.3.6.1.4.1.9.1.212
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 802 ISDN Router 1.3.6.1.4.1.9.1.213
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 803 ISDN Router 1.3.6.1.4.1.9.1.214
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 804 ISDN Router 1.3.6.1.4.1.9.1.215
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 805 Serial Router 1.3.6.1.4.1.9.1.245
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 827-4V ADSL Router 1.3.6.1.4.1.9.1.270
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 827 ADSL Router 1.3.6.1.4.1.9.1.284
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 811 Router 1.3.6.1.4.1.9.1.295
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 804J ISDN Router 1.3.6.1.4.1.9.1.296
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 826 ADSL Router 1.3.6.1.4.1.9.1.321
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
Cisco 826 ADSL Router 1.3.6.1.4.1.9.1.322
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 828 G.SHDSL Router 1.3.6.1.4.1.9.1.382
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 806 Broadband Router 1.3.6.1.4.1.9.1.384
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 811 ISDN Router 1.3.6.1.4.1.9.1.395
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 813 ISDN Router 1.3.6.1.4.1.9.1.396
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 827-H ADSL Router 1.3.6.1.4.1.9.1.446
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 837 ADSL Broadband Router 1.3.6.1.4.1.9.1.495
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 831 Ethernet Broadband Router 1.3.6.1.4.1.9.1.497
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 836 ADSL over ISDN Broadband Router 1.3.6.1.4.1.9.1.499
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
  • Cisco routers supply the User Tracking application with ARP Table information.
Cisco 851 Integrated Services Router 1.3.6.1.4.1.9.1.566
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
Cisco 857 Integrated Services Router 1.3.6.1.4.1.9.1.567
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
Cisco 876 Integrated Services Router 1.3.6.1.4.1.9.1.568
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Basic EnergyWise Management
Cisco 877 Integrated Services Router 1.3.6.1.4.1.9.1.569
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.
Cisco 878 Integrated Services Router 1.3.6.1.4.1.9.1.570
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Basic EnergyWise Management
Cisco 871 Integrated Services Router 1.3.6.1.4.1.9.1.571
  • Since this device (for Network Topology Layer 2 Services) does not support CDP MIB, Topology is partially supported. However, because of this, the device cannot be used as a seed device and cannot discover other devices that are further behind this device.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Basic EnergyWise Management
Cisco 877 Integrated Services Router (877M) 1.3.6.1.4.1.9.1.782

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 861/861W Integrated Services Router(CISCO861-K9,CISCO861W-GN-A-K9,CISCO861W-GN-E-K9,CISCO861W-GN-P-K9) 1.3.6.1.4.1.9.1.834

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Basic EnergyWise Management
Cisco 866 Router 1.3.6.1.4.1.9.1.835

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 867 Integrated Services Router 1.3.6.1.4.1.9.1.836

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 881/881W Integrated Services Router(CISCO881-K9,CISCO881W-GN-A-K9,CISCO881W-GN-E-K9,CISCO881W-GN-P-K9) 1.3.6.1.4.1.9.1.837

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 880 3G Integrated Services Router(CISCO881G-K9,CISCO881GW-GN-A-K9,CISCO881GW-GN-E-K9,CISCO881G-S-K9,CISCO881G-V-K9,CISCO881G-A-K9) 1.3.6.1.4.1.9.1.838

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Config Management
    • Image Management
    • Basic EnergyWise Management
Cisco 881 Integrated Services Router (881SRST) 1.3.6.1.4.1.9.1.840

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 886 Integrated Services Router 1.3.6.1.4.1.9.1.842

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 886 Integrated Services Router(886G) 1.3.6.1.4.1.9.1.843

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 886 SRST,886SRSTW Integrated Services Router (C886SRST-K9, C886SRSTW-GN-E-K9 ) 1.3.6.1.4.1.9.1.846

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Basic EnergyWise Management
Cisco 887 Integrated Services Router 1.3.6.1.4.1.9.1.847

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 887 Integrated Services Routers(887G) 1.3.6.1.4.1.9.1.848

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Basic EnergyWise Management
Cisco 887 SRST, 887SRSTW Integrated Services Router (C887SRST-K9, C887SRSTW-GN-E-K9) 1.3.6.1.4.1.9.1.851

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Basic EnergyWise Management
Cisco 888, 888W Integrated Services Router 1.3.6.1.4.1.9.1.852
  • Contact TAC (Technical Assistance Center) to access this support. You can also contact TAC at http://www.cisco.com/cisco/web/siteassets/contacts/index.html

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Image Management
    • Basic EnergyWise Management
Cisco 888 Integrated Services Router(888G) 1.3.6.1.4.1.9.1.853

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 888 Integrated Services Router (888SRST) 1.3.6.1.4.1.9.1.856

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 891 Integrated Services Router(CISCO891-K9,CISCO891W-AGN-A-K9,CISCO891W-AGN-C-K9,CISCO891W-AGN-N-K9) 1.3.6.1.4.1.9.1.857

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 892 Integrated Services Router(CISCO892-K9,CISCO892J-K9,CISCO892W-AGN-E-K9,CISCO892W-AGN-P-K9) 1.3.6.1.4.1.9.1.858

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Basic EnergyWise Management
Cisco 885 Integrated Services Router (885-D-3) 1.3.6.1.4.1.9.1.859

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 885 Integrated Services Router (885-E/J-3) 1.3.6.1.4.1.9.1.861
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco 819 Hardened Integrated Services Router 1.3.6.1.4.1.9.1.1384
  • The following feature support is not available for this device:
    • Inventory Config and Image management

 
Cisco 819 Hardened Integrated Services Router 1.3.6.1.4.1.9.1.1385
  • The following feature support is not available for this device:
    • Inventory Config and Image management

 
Cisco 819 Hardened Integrated Services Router 1.3.6.1.4.1.9.1.1386
  • The following feature support is not available for this device:
    • Inventory Config and Image management

 
Cisco 819 Hardened Integrated Services Router 1.3.6.1.4.1.9.1.1387
  • The following feature support is not available for this device:
    • Inventory Config and Image management

 
Cisco 819 Hardened Integrated Services Router 1.3.6.1.4.1.9.1.1388
  • The following feature support is not available for this device:
    • Inventory Config and Image management

     

 
Cisco 888EA Integrated Services Router 1.3.6.1.4.1.9.1.1542
  • The following feature support is not available for this device:
    • Inventory Config and Image management
    • Network Topology Layer 2 Services
Cisco 819 Hardened Integrated Services Router 1.3.6.1.4.1.9.1.1389
  • The following feature support is not available for this device:
    • Inventory Config and Image management
Cisco 819 Non-Hardened Integrated Services Router 1.3.6.1.4.1.9.1.1495
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management
Cisco 819 Non-Hardened Integrated Services Router 1.3.6.1.4.1.9.1.1496
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management
Cisco 819 Non-Hardened Integrated Services Router 1.3.6.1.4.1.9.1.1497
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management
Cisco 819 Hardened Integrated Services Router 1.3.6.1.4.1.9.1.1494
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management
Cisco 819 Hardened Integrated Services Router 1.3.6.1.4.1.9.1.1531
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management

 
Cisco 866VAE Integrated Services Router 1.3.6.1.4.1.9.1.1675
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco 867VAE Integrated Services Router 1.3.6.1.4.1.9.1.1676
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco 867VAE Integrated Services Router 1.3.6.1.4.1.9.1.1677
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 

Cisco 1800 Series Routers
Device Name sysObjectID Special Notes
Cisco 1861E Integrated Services Router 1.3.6.1.4.1.9.1.1339
  • CiscoView is untested
  • The following features are untested.
    • Inventory, Config and Image management
  • Supports SCP protocol for Configuration fetching and deploying tasks.
Cisco 1861E Integrated Services Router 1.3.6.1.4.1.9.1.1340
  • CiscoView is untested
  • The following features are untested.
    • Inventory, Config and Image management
  • Supports SCP protocol for Configuration fetching and deploying tasks.
Cisco 1861E Integrated Services Router 1.3.6.1.4.1.9.1.1341
  • The following features are untested.
    • Inventory, Config and Image management
  • Supports SCP protocol for Configuration fetching and deploying tasks.
Cisco 1861E Integrated Services Router 1.3.6.1.4.1.9.1.1342
  • CiscoView is untested
  • The following features are untested.
    • Inventory, Config and Image management
  • Supports SCP protocol for Configuration fetching and deploying tasks.
Cisco 1861E Integrated Services Router 1.3.6.1.4.1.9.1.1343
  • CiscoView is untested
  • The following features are untested.
    • Inventory, Config and Image management
  • Supports SCP protocol for Configuration fetching and deploying tasks.
Cisco 1861E Integrated Services Router 1.3.6.1.4.1.9.1.1344
  • CiscoView is untested
  • The following features are untested.
    • Inventory, Config and Image management
  • Supports SCP protocol for Configuration fetching and deploying tasks.
Cisco 1841 Integrated Services Router 1.3.6.1.4.1.9.1.1369
  • CiscoView support is not available for this device.
  • Supports SCP protocol for Configuration fetching and deploying tasks.
 

Cisco Catalyst 2350 Series Switches
Device Name sysObjectID Special Notes
Cisco Catalyst 2350-48TD-S Switch (Catalyst 2350-48TD-S) 1.3.6.1.4.1.9.1.1104
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • User Tracking
    • Image Distribution using SSH

Cisco Catalyst 2960 Series Switches
Device Name sysObjectID Special Notes
Cisco Catalyst 2960-48TT-S Switch (Cisco Catalyst 2960-48TT-S) 1.3.6.1.4.1.9.1.1005

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst 2960-8TC-S Compact Switch (Cisco Catalyst 2960-8TC-S) 1.3.6.1.4.1.9.1.1006

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst 2960-48PST-L Switch (WS-C2960-48PST-L) 1.3.6.1.4.1.9.1.1016

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Smart Install
Cisco Catalyst 2960-24LC-S Switch 1.3.6.1.4.1.9.1.1146

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 2960-24PC-S Switch 1.3.6.1.4.1.9.1.1147

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 2960-48PST-S Switch 1.3.6.1.4.1.9.1.1148

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 2960S-24TS-S Switch (WS-C2960S-24TS-S) 1.3.6.1.4.1.9.1.1257

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 2960S-48FPD-L Switch (WS-C2960S-48FPD-L) 1.3.6.1.4.1.9.1.1258

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 2960S-48LPD-L Switch (WS-C2960S-48LPD-L) 1.3.6.1.4.1.9.1.1259

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 2960S-48TD-L Switch (WS-C2960S-48TD-L) 1.3.6.1.4.1.9.1.1260

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 2960S-24PD-L Switch (WS-C2960S-24PD-L) 1.3.6.1.4.1.9.1.1261

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 2960S-24TD-L Switch (WS-C2960S-24TD-L) 1.3.6.1.4.1.9.1.1262

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 2960S-48FPS-L Switch (WS-C2960S-48FPS-L) 1.3.6.1.4.1.9.1.1263

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 2960S-48LPS-L Switch (WS-C2960S-48LPS-L) 1.3.6.1.4.1.9.1.1264

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 2960S-24PS-L Switch (WS-C2960S-24PS-L) 1.3.6.1.4.1.9.1.1265

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 2960S-48TS-L Switch (WS-C2960S-48TS-L) 1.3.6.1.4.1.9.1.1266

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 2960S-24TS-L Switch (WS-C2960S-24TS-L) 1.3.6.1.4.1.9.1.1267

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 2960-8TC Compact Switch 1.3.6.1.4.1.9.1.798
  • Support for IP Phones is also provided.
Cisco Catalyst 2960G-8TC Compact Switch 1.3.6.1.4.1.9.1.799
  • Support for IP Phones is also provided.
Cisco Catalyst 2960-48TC-S Switch 1.3.6.1.4.1.9.1.927
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco Catalyst 2960-24TC-S Switch 1.3.6.1.4.1.9.1.928
  • IP Phones are supported.
  • Dynamic User Tracking is supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco Catalyst 2960-24-S Switch 1.3.6.1.4.1.9.1.929
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco Catalyst 2960-24PC-L Switch (WS-C2960- 24PC-L) 1.3.6.1.4.1.9.1.950
  • IP Phones are supported.
  • Add/Import images is not supported if the device is in install mode.
  • WLSE system software, WLSE_SW is supported in Software Image Management.
  • Contact TAC (Technical Assistance Center) to access this support. You can also contact TAC at http://www.cisco.com/cisco/web/siteassets/contacts/index.html

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Image Management
    • Remote staging using External FTP
Cisco Catalyst 2960-24LT-L Switch (WS-C2960- 24LT-L) 1.3.6.1.4.1.9.1.951
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco Catalyst 2960PD-8TT-L Compact Switch (WS-C2960PD- 8TT-L) 1.3.6.1.4.1.9.1.952
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

 
 

Cisco Catalyst 2960-SF Series Switches
Device Name sysObjectID Special Notes
Cisco Catalyst 2960S-F48TS-S Switch 1.3.6.1.4.1.9.1.1654
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management
Cisco Catalyst 2960S-F24TS-S Switch 1.3.6.1.4.1.9.1.1655
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management
 

Cisco Catalyst 2960-X Series Switches
Device Name sysObjectID Special Notes
Cisco Catalyst 2960X-48FPD-L Switch 1.3.6.1.4.1.9.1.1181
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-48FPD-L Switch 1.3.6.1.4.1.9.1.1690
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-48LPD-L Switch 1.3.6.1.4.1.9.1.1182
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-48LPD-L Switch 1.3.6.1.4.1.9.1.1691
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-24PD-L Switch 1.3.6.1.4.1.9.1.1184
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-24PD-L Switch 1.3.6.1.4.1.9.1.1693
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-24TD-L Switch 1.3.6.1.4.1.9.1.1185
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-24TD-L Switch 1.3.6.1.4.1.9.1.1694
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-48FPS-L Switch 1.3.6.1.4.1.9.1.1186
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-48FPS-L Switch 1.3.6.1.4.1.9.1.1695
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-48LPS-L Switch 1.3.6.1.4.1.9.1.1187
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-48LPS-L Switch 1.3.6.1.4.1.9.1.1696
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-24PS-L Switch 1.3.6.1.4.1.9.1.1188
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-24PS-L Switch 1.3.6.1.4.1.9.1.1697
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-48TS-L Switch 1.3.6.1.4.1.9.1.1189
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-48TS-L Switch 1.3.6.1.4.1.9.1.1698
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-24TS-L Switch 1.3.6.1.4.1.9.1.1190
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-24TS-S Switch 1.3.6.1.4.1.9.1.1179
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-48TS-S Switch 1.3.6.1.4.1.9.1.1180
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-48LTD-L Switch 1.3.6.1.4.1.9.1.1183
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-48TD-L Switch 1.3.6.1.4.1.9.1.1692
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-24PSK-L Switch 1.3.6.1.4.1.9.1.1700
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-48LPS-S Switch 1.3.6.1.4.1.9.1.1701
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-24PS-S Switch 1.3.6.1.4.1.9.1.1702
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-48TS-LL Switch 1.3.6.1.4.1.9.1.1703
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
Cisco Catalyst 2960X-24TS-LL Switch 1.3.6.1.4.1.9.1.1704
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management
 

Cisco Catalyst 2960-Plus Series Switches
Device Name sysObjectID Special Notes
Cisco Catalyst 2960-Plus 24LC-L Switch 1.3.6.1.4.1.9.1.1750
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960-Plus 24LC-S Switch 1.3.6.1.4.1.9.1.1755
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960-Plus 24PC-L Switch 1.3.6.1.4.1.9.1.1749
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960-Plus 24PC-S Switch 1.3.6.1.4.1.9.1.1754
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960-Plus 24TC-L Switch 1.3.6.1.4.1.9.1.1752
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960-Plus 24TC-S Switch 1.3.6.1.4.1.9.1.1757
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960-Plus 48PST-L Switch 1.3.6.1.4.1.9.1.1748
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960-Plus 48PST-S Switch 1.3.6.1.4.1.9.1.1753
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960-Plus 48TC-S Switch 1.3.6.1.4.1.9.1.1756
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, User Tracking, VLAN Management
    • Fault Management

 
 

Cisco Catalyst 2960-XR Series Switches
Device Name sysObjectID Special Notes
Cisco Catalyst 2960XR-48FPD-I Switch 1.3.6.1.4.1.9.1.1797
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-48LPD-I Switch 1.3.6.1.4.1.9.1.1798
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-24PD-I Switch 1.3.6.1.4.1.9.1.1800
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-24TD-I Switch 1.3.6.1.4.1.9.1.1801
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-48FPS-I Switch 1.3.6.1.4.1.9.1.1802
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-48LPS-I Switch 1.3.6.1.4.1.9.1.1803
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-48TS-I Switch 1.3.6.1.4.1.9.1.1804
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-24PS-I Switch 1.3.6.1.4.1.9.1.1805
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-24TS-I Switch 1.3.6.1.4.1.9.1.1806
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-48FPD-L Switch 1.3.6.1.4.1.9.1.1807
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-48LPD-L Switch 1.3.6.1.4.1.9.1.1808
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-48TD-L Switch 1.3.6.1.4.1.9.1.1809
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-24PD-L Switch 1.3.6.1.4.1.9.1.1810
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-24TD-L Switch 1.3.6.1.4.1.9.1.1811
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-48FPS-L Switch 1.3.6.1.4.1.9.1.1812
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-48LPS-L Switch 1.3.6.1.4.1.9.1.1813
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-48TS-L Switch 1.3.6.1.4.1.9.1.1814
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-24PS-L Switch 1.3.6.1.4.1.9.1.1815
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 2960XR-24TS-L Switch 1.3.6.1.4.1.9.1.1816
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 

Cisco Catalyst 3560 Series Switches
Device Name sysObjectID Special Notes
Cisco Catalyst 3560-12PC-S Compact Switch (WS-C3560-12PC-S) 1.3.6.1.4.1.9.1.1015

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst 3560V2-24DC Switch(WS-C3560V2-24TS-SD) 1.3.6.1.4.1.9.1.1019

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Smart Install
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 3560V2-24TS Switch(WS-C3560V2-24TS) 1.3.6.1.4.1.9.1.1020

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Advanced EnergyWise Management
    • Smart Install
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 3560V2-24PS Switch(WS-C3560V2-24PS) 1.3.6.1.4.1.9.1.1021

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 3560V2-48TS Switch(WS-C3560V2-48TS) 1.3.6.1.4.1.9.1.1024

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Smart Install
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 3560V2-48PS Switch(WS-C3560V2-48PS) 1.3.6.1.4.1.9.1.1025

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Image Management
    • Advanced EnergyWise Management
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 3560X-24T-L,S Switch (WS-C3560X-24T-L, WS-C3560X-24T-S) 1.3.6.1.4.1.9.1.1226

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Smart Install
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 3560X-48T-L,S Switch (WS-C3560X-48T-L,WS-C3560X-48T-S) 1.3.6.1.4.1.9.1.1227

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Smart Install
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 3560X-24P-L,S Switch (WS-C3560X-24P-L, WS-C3560X-24P-S) 1.3.6.1.4.1.9.1.1228

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Smart Install
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 3560X-48PF-L,S Switch (WS-C3560X-48P-L, WS-C3560X-48P-S, WS-C3560X-48PF-L, WS-C3560X-48PF-S) 1.3.6.1.4.1.9.1.1229

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Smart Install
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 3560-24PS Switch 1.3.6.1.4.1.9.1.563
  • Support for IP Phones is also provided.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Smart Install
Cisco Catalyst IOS 3560-48PS Switch 1.3.6.1.4.1.9.1.564
  • Support for IP Phones is also provided.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Smart Install
Cisco Catalyst 3560G-24TS Switch 1.3.6.1.4.1.9.1.615
  • Support for IP Phones is also provided.
Cisco Catalyst 3560G-48TS Switch 1.3.6.1.4.1.9.1.617
  • Support for IP Phones is also provided.
Cisco Catalyst 3560-48TS Switch 1.3.6.1.4.1.9.1.634
  • Support for IP Phones is also provided.
Cisco Catalyst 3560-8PC Compact Switch 1.3.6.1.4.1.9.1.797
  • Support for IP Phones is also provided.
Cisco Catalyst 3560CPD-8PT-S Compact Switch 1.3.6.1.4.1.9.1.1368

 

  
  • Fault Management : CSCtr43250 (For Sake Takara and Syndrome device type,while walking ifHCInOctets/ifHCOutUcastPkts mib variables getting parser error so events depend on that mib variable are not getting generated (HighBroadcastRate, HighQueueDropRate, HighDiscardRate)

     

 

Cisco Catalyst 3560-E Series Switches
Device Name sysObjectID Special Notes
Cisco Catalyst 3560E-48TD-E,S Switch 1.3.6.1.4.1.9.1.794
  • Support for IP Phones is also provided.
Cisco Catalyst 3560E-24PD-E,S Switch 1.3.6.1.4.1.9.1.795
  • Support for IP Phones is also provided.
Cisco Catalyst 3560E-48PD-E,S Switch 1.3.6.1.4.1.9.1.796
  • Support for IP Phones is also provided.
Cisco Catalyst 3560E-12D-S,E Switch 1.3.6.1.4.1.9.1.930
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.
Cisco Catalyst 3560E-12SD-E,S Switch 1.3.6.1.4.1.9.1.956
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Remote staging using External FTP

Cisco Catalyst 3650 Series Switches
Device Name sysObjectID Special Notes
Cisco Catalyst 3650-24TS-E Switch 1.3.6.1.4.1.9.1.1823
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 3650-48TS-E Switch 1.3.6.1.4.1.9.1.1824
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 3650-24PS-E Switch 1.3.6.1.4.1.9.1.1825
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 3650-48PS-E Switch 1.3.6.1.4.1.9.1.1826
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 3650-24TD-E Switch 1.3.6.1.4.1.9.1.1827
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 3650-48TD-E Switch 1.3.6.1.4.1.9.1.1828
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 3650-24PD-E Switch 1.3.6.1.4.1.9.1.1829
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 3650-48PQ-E Switch 1.3.6.1.4.1.9.1.1881
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 
Cisco Catalyst 3650-48TQ-E Switch 1.3.6.1.4.1.9.1.1882
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management

 

Cisco Catalyst 3750 Series Switches
Device Name sysObjectID Special Notes
Cisco Catalyst 3750V2-24TS Switch(WS-C3750V2-24TS) 1.3.6.1.4.1.9.1.1022

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Advanced EnergyWise Management
    • Smart Install
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 3750V2-24PS Switch (WS-C3750V2-24PS) 1.3.6.1.4.1.9.1.1023

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Smart Install
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 3750V2-48TS Switch(WS-C3750V2-48TS) 1.3.6.1.4.1.9.1.1026

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Smart Install
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 3750V2-48PS Switch (WS-C3750V2-48PS) 1.3.6.1.4.1.9.1.1027

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Smart Install
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 3750X-24T-L,S Switch (WS-C3750X-24T-L, WS-C3750X-24T-S) 1.3.6.1.4.1.9.1.1222

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco Catalyst 3750X-48T-L,S Switch (WS-C3750X-48T-L, WS-C3750X-48T-S) 1.3.6.1.4.1.9.1.1223

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Smart Install
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 3750X-24P-L,S Switch (WS-C3750X-24P-L, WS-C3750X-24P-S) 1.3.6.1.4.1.9.1.1224

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Advanced EnergyWise Management
    • Smart Install
    • Identity Management
    • Auto SmartPort
Cisco Catalyst 3750G-24 Switch 1.3.6.1.4.1.9.1.511
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
Cisco Catalyst 3750G-48 Switch 1.3.6.1.4.1.9.1.512
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst 3750-24TS Switch (WS-C3750-24TS-E) (WS-C3750-24TS-S) 1.3.6.1.4.1.9.1.513
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst 3750G-24T Switch 1.3.6.1.4.1.9.1.514
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst 3750 Stack Switch 1.3.6.1.4.1.9.1.516
  • Support for VLAN Port Assignment not provided.
  • Support for IP Phones is also provided.
  • For Image Import, only BIN images directly under FLASH are supported.
Cisco Catalyst 3750G-12S Switch 1.3.6.1.4.1.9.1.530
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.
Cisco Catalyst 3750-48PS Switch (WS-C3750-48PS-E)(WS-C3750-48PS-S) 1.3.6.1.4.1.9.1.535
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst 3750-24PS Switch 1.3.6.1.4.1.9.1.536
  • IP Phones are supported.
  • Dynamic User Tracking is supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.
Cisco Catalyst 3750G-24PS Switch (WS-C3750G- 24PS-E) (WS-C3750G- 24PS-S) 1.3.6.1.4.1.9.1.602
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst 3750G-48PS Switch (WS-C3750G- 48PS-E) (WS-C3750G- 48PS-S) 1.3.6.1.4.1.9.1.603
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst 3750G-48TS Switch (WS-C3750G- 48TS-E) (WS-C3750G- 48TS-S) 1.3.6.1.4.1.9.1.604
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst 3750G-24TS-1U Switch (WS-C3750G-24TS-E1U) (WS-C3750G-24TS-S1U) (WS-C3750G- 24TS-E) (WS-C3750G- 24TS-S) 1.3.6.1.4.1.9.1.624
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst 3750-24FS Switch (WS-C3750-24FS-S) 1.3.6.1.4.1.9.1.656
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco 2600,2800,3700,3800 Series 16-Port EtherSwitch Service Module (NME-16ES-1G-P) 1.3.6.1.4.1.9.1.663
  • IP Phones are supported.
  • Add/Import images is not supported if the device is in install mode.
  • WLSE system software, WLSE_SW is supported in Software Image Management.
  • Contact TAC (Technical Assistance Center) to access this support. You can also contact TAC at http://www.cisco.com/cisco/web/siteassets/contacts/index.html

  • The following features are untested. Support for this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • VLAN Management
    • User Tracking
    • Config Management
    • Image Management
    • Support for dual supervisor modules
    • Image Distribution using SSH
Cisco catalyst 3750G-12S-SD Switch (WS-C3750G-12S), (WS-C3750G-12S-SD) 1.3.6.1.4.1.9.1.688
  • Support for IP Phones is also provided.
Cisco Catalyst 3750G-24WS-S25 Switch (WS-C3750G-24WS-S25) 1.3.6.1.4.1.9.1.778

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
Cisco Catalyst 3750G-24WS-S50 Switch (WS-C3750G-24WS-S50) 1.3.6.1.4.1.9.1.779

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
Cisco Catalyst 3750X-24S-S Switch 1.3.6.1.4.1.9.1.1404

 

  
  • Network Topology Layer 2 Services : CSCtr47486 ( The duplex mode of the Fast Ethernet port is shown wrongly. It shows as the unknown duplex mode where as in device it shows as auto duplex mode)

 

 

Cisco Catalyst 3750-E Series Switches
Device Name sysObjectID Special Notes
Cisco Catalyst 3750E-24TD-E,S Switch 1.3.6.1.4.1.9.1.789
  • Support for IP Phones is also provided.
Cisco Catalyst 3750E-48TD-E,S Switch 1.3.6.1.4.1.9.1.790
  • Support for IP Phones is also provided.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco Catalyst 3750E-48PD-E,S Switch 1.3.6.1.4.1.9.1.791
  • Support for IP Phones is also provided.
Cisco Catalyst 3750E-24PD-E,S Switch 1.3.6.1.4.1.9.1.792
  • Support for IP Phones is also provided.
 

Cisco Catalyst 3850 Series Switches

Device Name sysObjectID Special Notes
Cisco Catalyst 3850-48P-E Switch 1.3.6.1.4.1.9.1.1641
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management
  • User Tracking is not supported.
Cisco Catalyst 3850-48P-S Switch 1.3.6.1.4.1.9.1.1643
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management
  • User Tracking is not supported.
Cisco Catalyst 3850-24P-S Switch 1.3.6.1.4.1.9.1.1644
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management
  • User Tracking is not supported.
Cisco Catalyst 3850-48U-E Switch 1.3.6.1.4.1.9.1.1768
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services, VLAN Management
    • Fault Management
  • User Tracking is not supported.

 

Cisco Catalyst 4500 Series Switches
Device Name sysObjectID Special Notes
Cisco catalyst 4507R Switch 1.3.6.1.4.1.9.1.501
  • Supports Cisco IOS only.
  • On the Catalyst 4507, Fault Management supports the Supervisor Engine IV running the IOS operating system.
Cisco Catalyst 4506 Switch 1.3.6.1.4.1.9.1.502
  • Supported with CatOS only.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Basic EnergyWise Management
    • Advanced EnergyWise Management
Cisco Catalyst 4503 Switch 1.3.6.1.4.1.9.1.503
  • On the Catalyst 4503 and 4506, Fault Management supports the Supervisor Engine I and II running the CatOS operating system, and the Supervisor Engine III and IV running the IOS operating system.
  • Supported with CatOS only.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Basic EnergyWise Management
    • Identity Management
Cisco Catalyst 4510R SUP V Switch 1.3.6.1.4.1.9.1.537
  • Support for IP Phones is also provided.
Cisco Catalyst 4503-E Switch 1.3.6.1.4.1.9.1.874
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
Cisco Catalyst 4506-E Switch 1.3.6.1.4.1.9.1.875
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.
  • Contact TAC (Technical Assistance Center) to access this support. You can also contact TAC at http://www.cisco.com/cisco/web/siteassets/contacts/index.html

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • User Tracking
    • Image Management
    • Image Distribution using SSH
Cisco Catalyst 4507R-E Switch 1.3.6.1.4.1.9.1.876
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
Cisco Catalyst 4510R-E Switch 1.3.6.1.4.1.9.1.877
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.
  • Contact TAC (Technical Assistance Center) to access this support. You can also contact TAC at http://www.cisco.com/cisco/web/siteassets/contacts/index.html

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • User Tracking
    • Image Management
    • Image Distribution using SSH
Cisco Catalyst 4503 Switch 1.3.6.1.4.1.9.5.58
  • Supports Cisco IOS and CatOS in Network Topology Layer 2 Services.
  • Supported with CatOS only.

Cisco Catalyst 6500 Series Switches
Device Name sysObjectID Special Notes
Cisco Catalyst 6509 Switch (6582-2PA & WiSM - Card Support) 1.3.6.1.4.1.9.1.283
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Basic EnergyWise Management
    • Advanced EnergyWise Management
Cisco Catalyst 6503 Switch 1.3.6.1.4.1.9.1.449
  • User Tracking not supported in IOS 12.1(13)EW1.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Basic EnergyWise Management
    • Advanced EnergyWise Management
Cisco Catalyst 6509-NEB-A Switch 1.3.6.1.4.1.9.1.534
  • Support for IP Phones is also provided.
Cisco Catalyst SUP720-3B, WS-SUP32-GE-3B with 6504-E Switch 1.3.6.1.4.1.9.1.657
  • Support for IP Phones is also provided.
Cisco Catalyst 6509-V-E Switch (WS-C6509-V-E) 1.3.6.1.4.1.9.1.832
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • User Tracking
    • Image Distribution using SSH
Cisco Virtual Switching System (WS-C6513) 1.3.6.1.4.1.9.1.896

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • IP Phone Tracking
    • Fault Management
    • Remote staging using external FTP
Cisco Catalyst WS-C6503 Switch 1.3.6.1.4.1.9.5.56
  • User Tracking not supported in IOS 12.1(13)EW1.
Cisco Catalyst SUP32-8GE with WS-6504-E Switch 1.3.6.1.4.1.9.5.64
  • Support for IP Phones is also provided.

Cisco Catalyst Blade Switch 3000 Series
Device Name sysObjectID Special Notes
Cisco Catalyst Switch Module 3012 for IBM BladeCenter 1.3.6.1.4.1.9.1.1000
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst Blade Switch 3125G for HP (WS-CBS3012-IBM-I) 1.3.6.1.4.1.9.1.1001
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst Blade Switch 3125X for HP (WS-CBS3125-X) 1.3.6.1.4.1.9.1.1002
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Blade Switch WS-3020 for HPQ (WS-C3020-HPQ) 1.3.6.1.4.1.9.1.748
  • Support for IP Phones is also provided.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
    • Config Management
Cisco Blade Switch WS-3030 for Dell 1.3.6.1.4.1.9.1.749
  • Support for IP Phones is also provided.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco Blade Switch WS-3040 for FSC 1.3.6.1.4.1.9.1.784
  • Support for IP Phones is also provided.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco Catalyst Switch Module 3110G-S for IBM BladeCenter (WS-CBS3110G-S) 1.3.6.1.4.1.9.1.909
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst Switch Module 3110G-S-I for IBM BladeCente(WS-CBS3110G-S-I) 1.3.6.1.4.1.9.1.910
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst Switch Module 3110X-S for IBM BladeCenter 1.3.6.1.4.1.9.1.911
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst Switch Module 3110X -S-I for IBM BladeCenter 1.3.6.1.4.1.9.1.912
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst Blade Switch 3120G-S for HP 1.3.6.1.4.1.9.1.918
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst Blade Switch 3120X-S for HP 1.3.6.1.4.1.9.1.919
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst Blade Switch 3032 for Dell M1000E 1.3.6.1.4.1.9.1.920
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • User Tracking
    • Remote staging using External FTP
    • Image Distribution using SSH
Cisco Catalyst Blade Switch 3130G-S for Dell M1000E 1.3.6.1.4.1.9.1.921
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst Blade Switch 3130X-S for Dell M1000E 1.3.6.1.4.1.9.1.922
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Stack of CBS3100 switch modules 1.3.6.1.4.1.9.1.946
  • The following feature is not supported:
    • Ciscoview
Cisco Catalyst Switch Module 3110X Stack for IBM BladeCenter 1.3.6.1.4.1.9.1.947
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst Blade Switch 3120X Stack for HP 1.3.6.1.4.1.9.1.948
  • The minimum supported software versions are 12.2(40)EX3 and 122-46.SE for dissimilar stack members
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.
Cisco Catalyst Blade Switch 3130X Stack for Dell M1000E 1.3.6.1.4.1.9.1.949
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • User Tracking
    • IP Phone Tracking
    • Remote staging using External FTP
    • Image Distribution using SSH
    • Remote staging using external FTP
Cisco Catalyst Switch Module 3012 (WS-CBS3012-IBM) 1.3.6.1.4.1.9.1.999
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP

Cisco Catalyst G-L3 Series Switches
Device Name sysObjectID Special Notes
Cisco Catalyst C2948G-L3 Ethernet Switch 1.3.6.1.4.1.9.1.275
  • Cisco Routers provide User Tracking application with ARP Table information.
Cisco Catalyst 4908-G-L3 Switch 1.3.6.1.4.1.9.1.298
  • Cisco Routers provide User Tracking application with ARP Table information.
Cisco Catalyst 4840G Switch 1.3.6.1.4.1.9.1.312
  • Cisco Routers provide User Tracking application with ARP Table information.
Cisco Catalyst 3750G-24 Switch 1.3.6.1.4.1.9.1.511
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
Cisco Catalyst 3750G-48 Switch 1.3.6.1.4.1.9.1.512
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst 3750-24TS Switch (WS-C3750-24TS-E) (WS-C3750-24TS-S) 1.3.6.1.4.1.9.1.513
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco Catalyst 3750G-24T Switch 1.3.6.1.4.1.9.1.514
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Remote staging using External FTP

Cisco Ethernet Switching Network Modules
Device Name sysObjectID Special Notes
Cisco Enhanced Layer 2 EtherSwitch Service Module (SM-ES2-16-P) 1.3.6.1.4.1.9.1.1048

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco Enhanced Layer 2, Layer 3 EtherSwitch Service Module (SM-ES3-16-P) 1.3.6.1.4.1.9.1.1049

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Config Management
    • Basic EnergyWise Management
    • Smart Install
Cisco Enhanced Layer 2, Layer 3 EtherSwitch Service Module (SM-ES3G-16-P) 1.3.6.1.4.1.9.1.1050

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Smart Install
Cisco Enhanced Layer 2 EtherSwitch Service Module (SM-ES2-24) 1.3.6.1.4.1.9.1.1051

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Basic EnergyWise Management
Cisco Enhanced Layer 2 EtherSwitch Service Module (SM-ES2-24-P) 1.3.6.1.4.1.9.1.1052

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco Enhanced Layer 2, Layer 3 EtherSwitch Service Module (SM-ES3-24-P) 1.3.6.1.4.1.9.1.1053

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Smart Install
Cisco Enhanced Layer 2, Layer 3 EtherSwitch Service Module (SM-ES3G-24-P) 1.3.6.1.4.1.9.1.1054

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management
    • Smart Install
Cisco 2600,2800,3700,3800 Series 16-Port EtherSwitch Service Module (NME-16ES-1G) 1.3.6.1.4.1.9.1.702
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.
  • Contact TAC (Technical Assistance Center) to access this support. You can also contact TAC at http://www.cisco.com/cisco/web/siteassets/contacts/index.html

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • VLAN Management
    • User Tracking
    • Config Management
    • Image Management
    • Support for dual supervisor modules
    • Image Distribution using SSH
Cisco 2800,3800 Series 23-Port EtherSwitch Service Module(NME-X-23ES-1G) 1.3.6.1.4.1.9.1.703

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
Cisco Enhanced Layer2,Layer3 EtherSwitch Service Module 1.3.6.1.4.1.9.1.1056
  • The following features are not supported for this device:
    • Fault Management
    • Ciscoview
Cisco Enhanced Layer2,Layer3 EtherSwitch Service Module 1.3.6.1.4.1.9.1.1057
  • The following features are not supported for this device:
    • Fault Management
    • Ciscoview


Cisco IE 3000 Series Switches

Device Name sysObjectID Special Notes
Cisco IE 3000-4TC Industrial Ethernet Switch 1.3.6.1.4.1.9.1.958
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco IE 3000-8TC Industrial Ethernet Switch 1.3.6.1.4.1.9.1.959
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Image Management

Cisco IE 2000U Series Switches
Device Name sysObjectID Special Notes
Cisco IE-2000U-16TC-G-X Industrial Ethernet Switch 1.3.6.1.4.1.9.1.1872
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Fault Management
Cisco IE-2000U-8TC-G Industrial Ethernet Switch 1.3.6.1.4.1.9.1.1870
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Fault Management
Cisco IE-2000U-4TS-G Industrial Ethernet Switch 1.3.6.1.4.1.9.1.1869
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Fault Management
Cisco IE-2000U-4T-G Industrial Ethernet Switch 1.3.6.1.4.1.9.1.1868
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Fault Management
Cisco IE-2000U-16TC-GP Industrial Ethernet Switch 1.3.6.1.4.1.9.1.1840
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Fault Management

Cisco ME 2400 Series Ethernet Switches
Device Name sysObjectID Special Notes
Cisco ME 2400-24TS-D Switch 1.3.6.1.4.1.9.1.735
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management

Cisco ME 3400 Series Ethernet Access Switches
Device Name sysObjectID Special Notes
CISCO ME-3400EG-2CS-A (ME-3400EG-2CS-A) 1.3.6.1.4.1.9.1.1007

  • ME3400 and ME3800 GigabitEthernet interfaces are configured in module ME-3400EG-12CS-M - Fixed Module 0 (1002). entPhysicalHardwareRev, entPhysicalFirmwareRev, entPhysicalSoftwareRev and entPhysicalModelName MIB variables are not returning the value for that module, so data collection process is unable to collect that module's port details in campus manager. Refer the bug "CSCtq40610" for more details.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
CISCO ME-3400EG-12CS (ME-3400EG-12CS-M) 1.3.6.1.4.1.9.1.1008

  • ME3400 and ME3800 GigabitEthernet interfaces are configured in module ME-3400EG-12CS-M - Fixed Module 0 (1002). entPhysicalHardwareRev, entPhysicalFirmwareRev, entPhysicalSoftwareRev and entPhysicalModelName MIB variables are not returning the value for that module, so data collection process is unable to collect that module's port details in campus manager. Refer the bug "CSCtq40610" for more details.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
CISCO ME-3400E-24TS (ME-3400E-24TS-M) 1.3.6.1.4.1.9.1.1009

  • ME3400 and ME3800 GigabitEthernet interfaces are configured in module ME-3400EG-12CS-M - Fixed Module 0 (1002). entPhysicalHardwareRev, entPhysicalFirmwareRev, entPhysicalSoftwareRev and entPhysicalModelName MIB variables are not returning the value for that module, so data collection process is unable to collect that module's port details in campus manager. Refer the bug "CSCtq40610" for more details.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Basic EnergyWise Management
Cisco ME 3400-24TS-A Switch 1.3.6.1.4.1.9.1.736
  • ME3400 and ME3800 GigabitEthernet interfaces are configured in module ME-3400EG-12CS-M - Fixed Module 0 (1002). entPhysicalHardwareRev, entPhysicalFirmwareRev, entPhysicalSoftwareRev and entPhysicalModelName MIB variables are not returning the value for that module, so data collection process is unable to collect that module's port details in campus manager. Refer the bug "CSCtq40610" for more details.
  • Support for IP Phones is also provided.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Basic EnergyWise Management
Cisco ME 3400-24TS-D Switch (ME-3400-24TS-D) 1.3.6.1.4.1.9.1.737
  • ME3400 and ME3800 GigabitEthernet interfaces are configured in module ME-3400EG-12CS-M - Fixed Module 0 (1002). entPhysicalHardwareRev, entPhysicalFirmwareRev, entPhysicalSoftwareRev and entPhysicalModelName MIB variables are not returning the value for that module, so data collection process is unable to collect that module's port details in campus manager. Refer the bug "CSCtq40610" for more details.
  • Support for IP Phones is also provided.
  • Clustering and stack are supported in the Catalyst 3500 series.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Basic EnergyWise Management
Cisco ME 3400G-12CS-A Switch (ME-3400G-12CS-A) 1.3.6.1.4.1.9.1.780
  • ME3400 and ME3800 GigabitEthernet interfaces are configured in module ME-3400EG-12CS-M - Fixed Module 0 (1002). entPhysicalHardwareRev, entPhysicalFirmwareRev, entPhysicalSoftwareRev and entPhysicalModelName MIB variables are not returning the value for that module, so data collection process is unable to collect that module's port details in campus manager. Refer the bug "CSCtq40610" for more details.
  • Support for IP Phones is also provided.
  • Dynamic User Tracking is supported.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Basic EnergyWise Management
Cisco ME 3400G-12CS-D Switch (ME-3400G-12CS-D) 1.3.6.1.4.1.9.1.781
  • ME3400 and ME3800 GigabitEthernet interfaces are configured in module ME-3400EG-12CS-M - Fixed Module 0 (1002). entPhysicalHardwareRev, entPhysicalFirmwareRev, entPhysicalSoftwareRev and entPhysicalModelName MIB variables are not returning the value for that module, so data collection process is unable to collect that module's port details in campus manager. Refer the bug "CSCtq40610" for more details.
  • Support for IP Phones is also provided.
  • Dynamic User Tracking is supported.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Basic EnergyWise Management
Cisco ME 3400G-2CS-A Switch (ME3400G-2CS-A) 1.3.6.1.4.1.9.1.825
  • ME3400 and ME3800 GigabitEthernet interfaces are configured in module ME-3400EG-12CS-M - Fixed Module 0 (1002). entPhysicalHardwareRev, entPhysicalFirmwareRev, entPhysicalSoftwareRev and entPhysicalModelName MIB variables are not returning the value for that module, so data collection process is unable to collect that module's port details in campus manager. Refer the bug "CSCtq40610" for more details.
  • IP Phones are supported.
  • Dynamic User Tracking is supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.
Cisco ME 3400-24FS-A Switch (ME-3400-24FS-A) 1.3.6.1.4.1.9.1.873
  • ME3400 and ME3800 GigabitEthernet interfaces are configured in module ME-3400EG-12CS-M - Fixed Module 0 (1002). entPhysicalHardwareRev, entPhysicalFirmwareRev, entPhysicalSoftwareRev and entPhysicalModelName MIB variables are not returning the value for that module, so data collection process is unable to collect that module's port details in campus manager. Refer the bug "CSCtq40610" for more details.
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
    • Basic EnergyWise Management

Cisco ME 4900 Series Ethernet Switches
Device Name sysObjectID Special Notes
Cisco ME 4924-10GE Switch 1.3.6.1.4.1.9.1.788
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management

Cisco MS200X Series Ethernet Access Switch
Device Name sysObjectID Special Notes
Cisco MS200X-24P 24-Port 10/100 PoE Ethernet Access Switch 1.3.6.1.4.1.9.6.2.1.1.1.2

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Network Topology Layer 2 Services
Cisco MS200X-24 24-Port 10/100 Ethernet Access Switch 1.3.6.1.4.1.9.6.2.1.1.1.1

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Network Topology Layer 2 Services

Cisco Connected Grid Modules
Device Name sysObjectID Special Notes
Cisco Connected Grid 6-port Ethernet Switch Module Interface Card 1.3.6.1.4.1.9.1.1346

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Network Topology Layer 2 Services, VLAN Management, User Tracking

Cisco Network Modules
Device Name sysObjectID Special Notes
Cisco Catalyst 5000 RSM 1.3.6.1.4.1.9.1.168
  • Cisco Routers provide User Tracking application with ARP Table information.
Cisco Catalyst 6000 Series Switches MSM 1.3.6.1.4.1.9.1.256
  • Cisco Routers provide User Tracking application with ARP Table information.
Cisco Catalyst 5500 RSM 1.3.6.1.4.1.9.1.257
  • Cisco Routers provide User Tracking application with ARP Table information.
Cisco Catalyst 6000 Series Supervisor Module with MSFC 1.3.6.1.4.1.9.1.258
  • Cisco Routers provide User Tracking application with ARP Table information.
Cisco Catalyst 6000 Multilayer Switch Feature Card MSFC2 1.3.6.1.4.1.9.1.301
  • Cisco Routers provide User Tracking application with ARP Table information.
Cisco Catalyst 6000 Multilayer Switch Feature Card MSFC3 WS-SUP 720 1.3.6.1.4.1.9.1.557
  • Cisco Routers provide User Tracking application with ARP Table information.
Cisco 2600,2800,3700,3800 Series 16-Port EtherSwitch Service Module (NME-16ES-1G-P) 1.3.6.1.4.1.9.1.663
  • IP Phones are supported.
  • Add/Import images is not supported if the device is in install mode.
  • WLSE system software, WLSE_SW is supported in Software Image Management.
  • Contact TAC (Technical Assistance Center) to access this support. You can also contact TAC at http://www.cisco.com/cisco/web/siteassets/contacts/index.html

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • VLAN Management
    • User Tracking
    • Config Management
    • Image Management
    • Support for dual supervisor modules
    • Image Distribution using SSH
Cisco 2800,3800 Series 23-Port EtherSwitch Service Module (NME-X-23ES-1GP) 1.3.6.1.4.1.9.1.664
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • User Tracking
    • Fault Management
    • Image Distribution using SSH
Cisco 2851,3800 Series 24-Port EtherSwitch (with Stackwise Connectors) Service Module (NME-X-24ES-1GP) 1.3.6.1.4.1.9.1.665
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Fault Management
    • Inventory Config and Image management
Cisco 2851,3800 Series 48-Port EtherSwitch Service Module (NME-XD-48ES-2S-P) 1.3.6.1.4.1.9.1.666
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • IP Phone Tracking
    • Fault Management
    • Remote staging using external FTP

Cisco Service Modules
Device Name sysObjectID Special Notes
Cisco WS-SVC-SAMI-BB (WS-SVC-SAMI-BB-K9) 1.3.6.1.4.1.9.1.744
  • Software Management: Support for the module requires IP address of the parent Catalyst 6000 or 7600 device with proper Telnet credentials.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Path Analysis
    • Image Management

Rockwell Automation Stratix 8000 Series Switches
Device Name sysObjectID Special Notes
Rockwell Stratix MS06T 1.3.6.1.4.1.9.1.960
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Image Management
    • Basic EnergyWise Management
Rockwell Stratix MS10T 1.3.6.1.4.1.9.1.961
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Image Management

Rockwell Stratix 5700 Series Switches
Device Name sysObjectID Special Notes
Rockwell Stratix BMS12T4E2CG 1.3.6.1.4.1.9.1.1735
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Fault Management
    • Network Topology Layer 2 Services, VLAN Management
Rockwell Stratix BMS12T4E2CG 1.3.6.1.4.1.9.1.1736
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Fault Management
    • Network Topology Layer 2 Services, VLAN Management

Cisco VG 200 Series Gateways
Device Name sysObjectID Special Notes
Cisco VG204 Analog Voice Gateway 1.3.6.1.4.1.9.1.963
  • Network Topology Layer 2 Services and CiscoView supports are not available for this device.
Cisco VG248 48-Port Analog Phone Gateway 1.3.6.1.4.1.9.1.404
  • Inventory Config and Image Management supports are not available for this device
Cisco VG202 Analog Voice Gateway 1.3.6.1.4.1.9.1.964
  • Network Topology Layer 2 Services and CiscoView supports are not available for this device.

Cisco Unified Computing
Device Name sysObjectID Special Notes
Cisco UCS 6248UP 48-Port Fabric Interconnect 1.3.6.1.4.1.9.12.3.1.3.1062
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management
Cisco UCS 6296UP 96-Port Fabric Interconnect 1.3.6.1.4.1.9.12.3.1.3.1063
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management

Cisco 5900 Series Embedded Services Routers
Device Name sysObjectID Special Notes
Cisco 5921 Embedded Services Router 1.3.6.1.4.1.9.1.1604
  • CiscoView support is not available for this device.
 

Cisco Aironet 2600 Series
Device Name sysObjectID Special Notes
Cisco Aironet 2600i Access Point 1.3.6.1.4.1.9.1.1657
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
 

Cisco Wide Area Virtualization Engines
Device Name sysObjectID Special Notes
Cisco WAVE 294 Wide Area Virtualization Engine 1.3.6.1.4.1.9.1.1354
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management
Cisco WAVE 694 Wide Area Virtualization Engine 1.3.6.1.4.1.9.1.1352
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management
Cisco WAVE 7571 Wide Area Virtualization Engine 1.3.6.1.4.1.9.1.1350
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management
Cisco WAVE 7541 Wide Area Virtualization Engine 1.3.6.1.4.1.9.1.1351
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management
Cisco WAVE 8541 Wide Area Virtualization Engine 1.3.6.1.4.1.9.1.1349
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management

 

IOS XR Devices

This table explains the specific support notes for all of the series of devices under IOS XR Devices family:


Cisco ASR 9000 Series Aggregation Services Routers
Device Name sysObjectID Special Notes
Cisco ASR 9010 Router 1.3.6.1.4.1.9.1.1017 The device is untested for Inventory config and image mgmt.
 

Cisco ASR 1000 Series Aggregation Services Routers
Device Name sysObjectID Special Notes
Cisco ASR 1002-X Router 1.3.6.1.4.1.9.1.1525
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management
    • Fault Management

 
 

Cisco ASR 901 10G Series Aggregation Services Routers
Device Name sysObjectID Special Notes
Cisco ASR 901-6CZ-F-D Router 1.3.6.1.4.1.9.1.1724
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Fault Management
    • Network Topology Layer 2 Services

 

Cisco Carrier Routing System
Device Name sysObjectID Special Notes
Cisco CRS-1 16-Slot Single-Shelf System 1.3.6.1.4.1.9.1.613
  • Only Inventory and Config mgmt support is available for this device and swim supported with defect CSCtq63762 for this device.
  • Devices are untested.
Cisco CRS-1 8-Slot Single-Shelf System 1.3.6.1.4.1.9.1.643
  • Only Inventory and Config mgmt support is available for this device and swim supported with defect CSCtq63762 for this device.
  • Devices are untested.
Cisco CRS-1 4-Slot Single-Shelf System 1.3.6.1.4.1.9.1.822
  • Only Inventory and Config mgmt support is available for this device and swim supported with defect CSCtq63762 for this device.

 
Network Analysis Modules

This table explains the specific support notes for all of the series of devices under Network Analysis Modules family:


Network Analysis Modules
Device Name sysObjectID Special Notes
Cisco WAAS Network Analysis Module (NAM) Virtual Blade 1.3.6.1.4.1.9.1.1169
  • Network Topology Layer 2 Services and CiscoView supports are not available for this device.
  • Only Inventory and Config mgmt support is available for this device and swim support is not available for this device.
Cisco Catalyst 6500 Series Network Analysis Module (NAM-3) 1.3.6.1.4.1.9.1.1529
  • Network Topology Layer 2 Services  support is not available for this device.
  • Inventory and Config mgmt support is not available for this device.

 
Cisco Nexus 1000V Network Analysis Module (NAM) Virtual Service Blade 1.3.6.1.4.1.9.1.1214
  • Network Topology Layer 2 Services and CiscoView supports are not available for this device.
  • Only Inventory and Config mgmt support is available for this device and swim support is not available for this device.
WS-SVC-NAM-1 1.3.6.1.4.1.9.5.1.3.1.1.2.914
  • Network Topology Layer 2 Services support is not available for this device
Cisco 2600,3660,3700 Series NAM 1.3.6.1.4.1.9.1.562
  • Network Topology Layer 2 Services support is not available for this device

 
WS-SVC-NAM-2 1.3.6.1.4.1.9.5.1.3.1.1.2.291
  • Network Topology Layer 2 Services support is not available for this device

 
6380-NAM 1.3.6.1.4.1.9.5.1.3.1.1.2.223
  • Network Topology Layer 2 Services support is not available for this device

 

 

Other Devices or Modules

This table explains the specific support notes for all of the series of devices under Other Devices/Modules family:


Cisco 7800 Series Media Convergence Servers
Device Name sysObjectID Special Notes
Cisco 7815I Media Convergence Server 1.3.6.1.4.1.9.1.582
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
Cisco 7825H Media Convergence Server 1.3.6.1.4.1.9.1.583
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
Cisco 7835H Media Convergence Server 1.3.6.1.4.1.9.1.584
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
Cisco 7835I Media Convergence Server 1.3.6.1.4.1.9.1.585
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
Cisco 7845H Media Convergence Server 1.3.6.1.4.1.9.1.586
  • The device Cisco 7845H Media Convergence Server has been tested on the softwares Cisco Unified Communications Manager Version 6.1.1 and Version 7.0.0.
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Inventory Config and Image management
Cisco 7845I Media Convergence Server 1.3.6.1.4.1.9.1.587
  • Netconfig of Configuration Management is not supported by Cisco MDS 9513 Multilayer Director Switch and Cisco MDS 9216i Multilayer Fabric Switch.
  • IP Phones are supported.
  • Only BIN images directly under FLASH are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
Cisco 7855I Media Convergence Server 1.3.6.1.4.1.9.1.588
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
Cisco 7865I Media Convergence Server 1.3.6.1.4.1.9.1.589
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
Cisco 7825I Media Convergence Server 1.3.6.1.4.1.9.1.746
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
Cisco 7816I Media Convergence Server (IBM) 1.3.6.1.4.1.9.1.898
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
Cisco 7828I Media Convergence Server (IBM) 1.3.6.1.4.1.9.1.899
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
Cisco 7816H Media Convergence Server (HP) 1.3.6.1.4.1.9.1.900
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Inventory Config and Image management
Cisco 7828H Media Convergence Server (HP) 1.3.6.1.4.1.9.1.901
  • IP Phones are supported.
  • WLSE system software, WLSE_SW is supported in Software Image Management.
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Network Topology Layer 2 Services
    • Inventory Config and Image management

Cisco Services-Ready Engine (SRE) Modules
Cisco Wide Area Application Services (WAAS) Modules for SRE 1.3.6.1.4.1.9.1.1212
  • CiscoView support is not available for this device.
  • Device is untested
Cisco Wide Area Application Services (WAAS) Modules for SRE 1.3.6.1.4.1.9.1.1213
  • CiscoView support is not available for this device.
  • Device is untested
Cisco Wide Area Application Services (WAAS) Modules for Integrated Service Routers 1.3.6.1.4.1.9.1.1209
  • CiscoView support is not available for this device.
  • Device is untested
Cisco Wide Area Application Services (WAAS) Modules for Integrated Service Routers 1.3.6.1.4.1.9.1.1210
  • CiscoView support is not available for this device.
  • Device is untested
Cisco Wide Area Application Services (WAAS) Modules for Integrated Service Routers 1.3.6.1.4.1.9.1.1211
  • CiscoView support is not available for this device.
  • Device is untested

Security Context Devices

This table explains the specific support notes for all of the series of devices under Security Context Devices family:


Cisco ASA 5500 Series Adaptive Security Appliances
Device Name sysObjectID Special Notes
Cisco ASA-5510 Adaptive Security Appliance (ASA5510-K8/ASA5510-SEC-BUN-K9) 1.3.6.1.4.1.9.1.669

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco ASA 5520 Adaptive Security Appliance 1.3.6.1.4.1.9.1.670

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco ASA 5520 Adaptive Security Appliance Security Context 1.3.6.1.4.1.9.1.671
  • After adding the device into the DCR, and whenever the device is switched between the Single and Multi Security Context Modes, the device should be deleted and added again into the DCR. This is due to change in the sysobjid and also because the number of configurations for the device varies when there is switching between the modes.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco ASA-5540 Adaptive Security Appliance (ASA5540-K8/ASA5540-BUN-K9) 1.3.6.1.4.1.9.1.672

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco ASA-5540 Adaptive Security Appliance (Multiple Security Contexts) 1.3.6.1.4.1.9.1.673
  • After adding the device into the DCR, and whenever the device is switched between the Single and Multi Security Context Modes, the device should be deleted and added again into the DCR. This is due to change in the sysobjid and also because the number of configurations for the device varies when there is switching between the modes.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco ASA-5505 Adaptive Security Appliance (ASA5505-K8/ASA5505-BUN-K9) 1.3.6.1.4.1.9.1.745

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco ASA-5550 Adaptive Security Appliance (ASA5550-K8/ASA5550-BUN-K9) 1.3.6.1.4.1.9.1.753

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco ASA-5550 Adaptive Security Appliance (Multiple Security Contexts) 1.3.6.1.4.1.9.1.763
  • After adding the device into the DCR, and whenever the device is switched between the Single and Multi Security Context Modes, the device should be deleted and added again into the DCR. This is due to change in the sysobjid and also because the number of configurations for the device varies when there is switching between the modes.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco ASA-5510 Adaptive Security Appliance (Multiple Security Contexts) 1.3.6.1.4.1.9.1.773
  • After adding the device into the DCR, and whenever the device is switched between the Single and Multi Security Context Modes, the device should be deleted and added again into the DCR. This is due to change in the sysobjid and also because the number of configurations for the device varies when there is switching between the modes.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco ASA-5580 Adaptive Security Appliance ( ASA5580-40-BUN-K8), (ASA5580-40-BUN-K9), (ASA5580-40-8GE-K9) 1.3.6.1.4.1.9.1.914

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco ASA-5580 Adaptive Security Appliance Security Context (ASA5580-40-BUN-K8), (ASA5580-40-BUN-K9), (ASA5580-40-8GE-K9) 1.3.6.1.4.1.9.1.915
  • The following features are untested. Support of this device category has already been tested in the earlier releases:
    • Inventory Config and Image management
    • Remote staging using External FTP
Cisco ASA 5512-X Adaptive Security Appliance Security Context 1.3.6.1.4.1.9.1.1411
  • The device is untested and Swim Support is not available for this device.
Cisco ASA 5512-X NPE Adaptive Security Appliance Security Context 1.3.6.1.4.1.9.1.1447
  • The device is untested and Swim Support is not available for this device.
Cisco ASA 5525-X Adaptive Security Appliance Security Context 1.3.6.1.4.1.9.1.1420
  • The device is untested and Swim Support is not available for this device.
Cisco ASA 5525-X NPE Adaptive Security Appliance Security Context 1.3.6.1.4.1.9.1.1448
  • The device is untested and Swim Support is not available for this device.

 
Cisco ASA 5525-X Adaptive Security Appliance Security Context 1.3.6.1.4.1.9.1.1412
  • The device is untested and Swim Support is not available for this device.

 
Cisco ASA 5525-X NPE Adaptive Security Appliance Security Context 1.3.6.1.4.1.9.1.1449
  • The device is untested and Swim Support is not available for this device.

 
Cisco ASA 5525-X Adaptive Security Appliance Security Context 1.3.6.1.4.1.9.1.1413
  • Swim Support is not available for this device.

 
Cisco ASA 5545-X Adaptive Security Appliance Security Context 1.3.6.1.4.1.9.1.1450
  • The device is untested and Swim Support is not available for this device.

 
Cisco ASA 5555-X Adaptive Security Appliance Security Context 1.3.6.1.4.1.9.1.1414
  • The device is untested and Swim Support is not available for this device.

 
Cisco ASA 5555-X Adaptive Security Appliance Security Context 1.3.6.1.4.1.9.1.1451
  • The device is untested and Swim Support is not available for this device.

 
Cisco ASA 5512-X Adaptive Security Appliance 1.3.6.1.4.1.9.1.1407
  • The device is untested and Swim Support is not available for this device.

 
Cisco ASA 5512-X Adaptive Security Appliance with No Payload Encryption 1.3.6.1.4.1.9.1.1442
  • The device is untested and Swim Support is not available for this device.

 
Cisco ASA 5525-X Adaptive Security Appliance 1.3.6.1.4.1.9.1.1421
  • The device is untested and Swim Support is not available for this device.

 
Cisco ASA 5515-X Adaptive Security Appliance with No Payload Encryption 1.3.6.1.4.1.9.1.1443
  • The device is untested and Swim Support is not available for this device.

 
Cisco ASA 5525-X Adaptive Security Appliance 1.3.6.1.4.1.9.1.1408
  • The device is untested and Swim Support is not available for this device.

 
Cisco ASA 5525-X Adaptive Security Appliance with No Payload Encryption 1.3.6.1.4.1.9.1.1444
  • The device is untested and Swim Support is not available for this device.

 
Cisco ASA 5545-X Adaptive Security Appliance 1.3.6.1.4.1.9.1.1409
  • The device is untested and Swim Support is not available for this device.

 
Cisco ASA 5545-X Adaptive Security Appliance with No Payload Encryption 1.3.6.1.4.1.9.1.1445
  • The device is untested and Swim Support is not available for this device.

 
Cisco ASA 5555-X Adaptive Security Appliance 1.3.6.1.4.1.9.1.1410
  • The device is untested and Swim Support is not available for this device.

 
Cisco ASA 5555-X NPE Adaptive Security Appliance with No Payload Encryption 1.3.6.1.4.1.9.1.1446
  • The device is untested and Swim Support is not available for this device.

 

Cisco PIX 500 Series Firewalls
Device Name sysObjectID Special Notes
PIX Firewall 1.3.6.1.4.1.9.1.227
  • These devices can also be managed through an Auto Update Server.
  • NetConfig support is not available if the software version 7.0 or above is running on PIX Firewall devices.
  • Check product documentation of individual PIX Firewall device for supported software versions.
Cisco PIX 506 Firewall 1.3.6.1.4.1.9.1.389
  • These devices can also be managed through an Auto Update Server.
  • NetConfig support is not available if the software version 7.0 or above is running on PIX Firewall devices.
  • Check product documentation of individual PIX Firewall device for supported software versions.
Cisco PIX 515 Firewall 1.3.6.1.4.1.9.1.390
  • These devices can also be managed through an Auto Update Server.
  • NetConfig support is not available if the software version 7.0 or above is running on PIX Firewall devices.
  • Check product documentation of individual PIX Firewall device for supported software versions.
Cisco PIX 520 Firewall 1.3.6.1.4.1.9.1.391
  • These devices can also be managed through an Auto Update Server.
  • NetConfig support is not available if the software version 7.0 or above is running on PIX Firewall devices.
Cisco PIX 525 Firewall 1.3.6.1.4.1.9.1.392
  • These devices can also be managed through an Auto Update Server.
  • NetConfig support is not available if the software version 7.0 or above is running on PIX Firewall devices.
PIX Firewall535 Proxy 1.3.6.1.4.1.9.1.393
  • These devices can also be managed through an Auto Update Server.
  • NetConfig support is not available if the software version 7.0 or above is running on PIX Firewall devices.
Cisco PIX 501 Firewall 1.3.6.1.4.1.9.1.417
  • These devices can also be managed through an Auto Update Server.
  • NetConfig support is not available if the software version 7.0 or above is running on PIX Firewall devices.
  • Check product documentation of individual PIX Firewall device for supported software versions.
Cisco PIX 506E Firewall 1.3.6.1.4.1.9.1.450
  • These devices can also be managed through an Auto Update Server.
  • NetConfig support is not available if the software version 7.0 or above is running on PIX Firewall devices.
  • Check product documentation of individual PIX Firewall device for supported software versions.
Cisco PIX 515E Firewall 1.3.6.1.4.1.9.1.451
  • These devices can also be managed through an Auto Update Server.
  • NetConfig support is not available if the software version 7.0 or above is running on PIX Firewall devices.
  • Check product documentation of individual PIX Firewall device for supported software versions.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco PIX 535 Firewall Security Context 1.3.6.1.4.1.9.1.675

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP
Cisco PIX 515 Firewall Security Context 1.3.6.1.4.1.9.1.678

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Inventory Config and Image management
    • Remote staging using External FTP

Cisco PIX 500 Series Security Appliances
Device Name sysObjectID Special Notes
Cisco PIX 515E Firewall (Multiple Security Contexts) 1.3.6.1.4.1.9.1.677
  • After adding the device into the DCR, and whenever the device is switched between the Single and Multi Security Context Modes, the device should be deleted and added again into the DCR. This is due to change in the sysobjid and also because the number of configurations for the device varies when there is switching between the modes.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Remote staging using External FTP

 
Storage and Data Center Switches

This table explains the specific support notes for all of the series of devices under Storage and Data Center Switches family:

Note: Non-admin VDC in a Nexus device is not supported in LMS.

Data Center Switches
Device Name sysObjectID Special Notes
Cisco Nexus 7000 10-Slot Switch 1.3.6.1.4.1.9.12.3.1.3.612
  • User Tracking is supported.
  • Dynamic User Tracking is not supported.
  • This device does not have mac notification feature.
  • Trap configuration is not supported.
  • When adding the Nexus devices to DCR, provide the netadmin SNMP RO credential. When other SNMP RO credential is provided, user tracking will not collect end host data.
  • The Nexus device should be running NXOS 5.1(1), 5.1(3) or later. 5.1(2) is not supported. For Ciscoview, minimum Nexus OS required is 5.2(0).
  • Configure the device to map community with context using the below command.
    snmp-server context <context-name> vrf <vrf-name>
    snmp-server mib community-map <snmp community> context <context-name>
Cisco Nexus 7000 18-Slot Switch(N7K-C7018) 1.3.6.1.4.1.9.12.3.1.3.777
  • User Tracking is supported.
  • Dynamic User Tracking is not supported.
  • This device does not have mac notification feature.
  • Trap configuration is not supported.
  • The Nexus device should be running NXOS 5.1(1), 5.1(3) or later. 5.1(2) is not supported. For Ciscoview, minimum Nexus OS required is 5.2(0).
  • When adding the Nexus devices to DCR, provide the netadmin SNMP RO credential. When other SNMP RO credential is provided, user tracking will not collect end host data.
  • Configure the device to map community with context using the below command.
    snmp-server context <context-name> vrf <vrf-name>
    snmp-server mib community-map <snmp community> context <context-name>
Cisco Nexus 7000 9-Slot Switch 1.3.6.1.4.1.9.12.3.1.3.932 The following feature is supported for this device:
  • FEX module

In Ciscoview, this Nexus device should be running on 5.2(0).
Cisco Nexus 3064 Switch 1.3.6.1.4.1.9.12.3.1.3.1105 The following feature is supported for this device:

Software Distribution by: Advanced flow, Image, Remote Staging
Cisco Nexus 5548P Switch 1.3.6.1.4.1.9.12.3.1.3.1008
  • CiscoView support is not available for this device.
  • Reload option in Swim has not been verified for this device.
Cisco MDS 9222i Multiservice Modular Switch 1.3.6.1.4.1.9.12.3.1.3.1175 Memory related components are not supported since the Corresponding Memory MIB variables are not supported for the device
Cisco Nexus 1010 Virtual Services Appliance 1.3.6.1.4.1.9.12.3.1.3.1668

Memory related components are not supported since the Corresponding Memory MIB variables are not supported for the device
Cisco Nexus 5020 Switch 1.3.6.1.4.1.9.12.3.1.3.720 User Tracking feature is untested. Since Support of this feature has already been tested with other device models
Cisco Nexus 5020T Switch 1.3.6.1.4.1.9.12.3.1.3.936 User Tracking feature is untested. Since Support of this feature has already been tested with other device models
Cisco Nexus 6001 Switch 1.3.6.1.4.1.9.12.3.1.3.1308

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Network Topology Layer 2 Services, VLAN Management

 

Wireless LAN Controllers

This table explains the specific support notes for all of the series of devices under Wireless LAN Controllers Devices family:


Cisco Services Modules
Device Name sysObjectID Special Notes
Cisco ACE Application Control Engine Module 1.3.6.1.4.1.9.1.1291
  • CiscoView support is not available for this device.
  • Device is untested.
  • Swim support is not available for this device

 

WLSE Devices

This table explains the specific support notes for all of the series of devices under WLSE Devices family:


CiscoWorks Wireless LAN Solution Engine
Device Name sysObjectID Special Notes
CiscoWorks 1130 for Wireless LAN Solution Engine 1.3.6.1.4.1.9.1.630
  • Netconfig of Configuration Management is not supported by Cisco MDS 9513 Multilayer Director Switch and Cisco MDS 9216i Multilayer Fabric Switch.
  • Only BIN images directly under FLASH are supported.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Image Management
CiscoWorks 1030 for Wireless LAN Solution Engine 1.3.6.1.4.1.9.1.631

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Remote staging using External FTP
    • Image Management
Cisco Wireless LAN Solution Engine S20 1.3.6.1.4.1.9.1.709

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Image Management
CiscoWorks 1133 for Wireless LAN Solution Engine 1.3.6.1.4.1.9.1.752
  • Netconfig of Configuration Management is not supported by Cisco MDS 9513 Multilayer Director Switch and Cisco MDS 9216i Multilayer Fabric Switch.
  • Only BIN images directly under FLASH are supported.

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Network Topology Layer 2 Services
    • Remote staging using External FTP
    • Image Management
CiscoWorks 1130 for Wireless LAN Solution Engine For Image version 2.11 and Later: 1.3.6.1.4.1.9.1.630
  • Configuration Management: Config deploy is not supported.
CiscoWorks 1030 for Wireless LAN Solution Engine For Image version 2.8: 1.3.6.1.4.1.9.1.459 For Image version 2.9: NA.
  • The minimum supportedsoftware versions are 12.2(40)EX3 and 122-46.SE for dissimilar stack members
CiscoWorks 1130 for Wireless LAN Solution Engine For Image version 2.8: NA. For Image version 2.9: 1.3.6.1.4.1.9.1.459
  • Configuration Management: Config deploy is not supported.
 
Cisco Small Business Series Managed Switches

This table explains the specific support notes for all of the series of devices under Cisco Small Business 300 Series Managed Switches family:


Cisco Small Business 300 Series Managed Switches
Device Name sysObjectID Special Notes
Cisco SG300-28P 28-Port Gigabit PoE Managed Switch 1.3.6.1.4.1.9.6.1.83.28.2
  • The following features are supported for this device:
    • Network Topology Layer 2 Services
    • Fault Management
Cisco ESW2-350G-52 52-Port Gigabit Managed Switch (For version 4.2 and 4.2.1) 1.3.6.1.4.1.9.6.1.86.52.1
  • Only CiscoView support is available for this device.
  • Inventory, Config, Network Topology, Image, and Fault Management support is not available for this device.

Cisco Small Business 500 Series Stackable Managed Switches
Device Name sysObjectID Special Notes
Cisco SG500-28 28-port Gigabit Stackable Managed Switch 1.3.6.1.4.1.9.6.1.81.28.1
  • The following features are supported for this device:
    • Ciscoview

     

  • The following features are not supported for this device:
    • Network Topology Layer 2 Services
    • Fault Management

Cisco Small Business 220 Series Smart Plus Switches
Device Name sysObjectID Special Notes
Cisco SG220-52 52-Port Gigabit Smart Plus Switch 1.3.6.1.4.1.9.6.1.89.52.5

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Network Topology Layer 2 Services
Cisco SG220-50P 50-Port Gigabit PoE Smart Plus Switch 1.3.6.1.4.1.9.6.1.89.50.2

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Network Topology Layer 2 Services
Cisco SG220-50 50-Port Gigabit Smart Plus Switch 1.3.6.1.4.1.9.6.1.89.50.1

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Network Topology Layer 2 Services
Cisco SG220-28MP 28-Port Gigabit PoE Smart Plus Switch 1.3.6.1.4.1.9.6.1.89.28.3

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Network Topology Layer 2 Services
Cisco SG220-28 28-Port Gigabit Smart Plus Switch 1.3.6.1.4.1.9.6.1.89.28.5

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Network Topology Layer 2 Services
Cisco SG220-26 26-Port Gigabit Smart Plus Switch 1.3.6.1.4.1.9.6.1.89.26.1

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Network Topology Layer 2 Services
Cisco SF220-24 24-Port 10/100 Smart Plus Switch 1.3.6.1.4.1.9.6.1.84.24.1

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Network Topology Layer 2 Services
Cisco SF220-24P 24-Port 10/100 PoE Smart Plus Switch 1.3.6.1.4.1.9.6.1.84.24.2

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Network Topology Layer 2 Services
Cisco SF220-48 48-Port 10/100 Smart Plus Switch 1.3.6.1.4.1.9.6.1.84.48.1

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Network Topology Layer 2 Services
Cisco SF220-48P 48-Port 10/100 PoE Smart Plus Switch 1.3.6.1.4.1.9.6.1.84.48.2

  • The following features are untested. Support of this device category has already been tested in the earlier releases:

    • Fault Management
    • Network Topology Layer 2 Services

 


Non-Cisco Devices
 

The Supported sysOIDs of the Non-Cisco Devices in LMS have been listed in mdfdata_NonCisco.xml. To access the file, follow the below mentioned path:

  • If, On Windows Platform - \NMSROOT\lib\classpath\com\cisco\nm\cwcs\mdf\mdfdata_NonCisco.xml 

                                                                         (or)

  • On Solaris and Soft Appliance - /opt/CSCOpx/lib/classpath/com/cisco/nm/cwcs/mdf/mdfdata_NonCisco.xml

If the sysOID for a device is not available on the list available in mdfdata_NonCisco.xml, it is then categorized as Unknown Device.

To know which are the supported and not supported features under Non-Cisco Devices, access the link given below:

http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/user/guide/inventory/dcr.html

 


CCDE, CCSI, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco Nurse Connect, Cisco Stackpower, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Special Notes and Exceptions for Devices Supported in Cisco Prime LAN Management Solution 4.2
Copyright © 1998-2011, Cisco Systems, Inc. All rights reserved

Part Number: OL-25955-01

Contributed by Cisco Engineers

Was this Document Helpful?

FeedbackFeedback

Contact Cisco

Related Support Community Discussions

This Document Applies to These Products

ABOUT US
CONTACT US
WORK WITH US