Frame Relay 64-Bit Counters
Feature History
|
|
12.0(17)S |
This feature was introduced on the Cisco 12000 series. |
12.2(4)T |
This feature was integrated into Cisco IOS Release 12.2(4)T. |
12.2(4)T3 |
Support for the Cisco 7500 series routers was added. |
12.0(21)S |
The frame-relay ifmib-counter64 command was introduced. |
12.3(10) |
The frame-relay ifmib-counter64 command was integrated into Cisco IOS Release 12.3(10). |
12.3(11)T |
The frame-relay ifmib-counter64 command was integrated into Cisco IOS Release 12.3(11)T. |
12.2(18)SXE |
The frame-relay ifmib-counter64 command was integrated into Cisco IOS Release 12.2(18)SXE. |
This document describes the Frame Relay 64-Bit Counters feature in Cisco IOS Release 12.2(4)T. It includes the following sections:
•Feature Overview
•Supported Platforms
•Supported Standards and MIBs and RFCs
•Prerequisites
•Configuration Tasks
•Monitoring and Maintaining Frame Relay 64-Bit Counters
•Configuration Examples
Feature Overview
The Frame Relay 64-Bit Counters feature provides 64-bit counter support on Frame Relay interfaces and subinterfaces. This feature enables the gathering of statistics through Simple Network Management Protocol (SNMP) for faster interfaces operating at OC-3, OC-12, and OC-48 speeds.
The following counters are supported by this feature: Bytes In, Bytes Out, Packets In, and Packets Out.
The show frame-relay pvc command has been modified to display the 64-bit counters.
Benefits
The values in 32-bit counters sometime wrap because the field is too small. Wrapping causes the values in these fields to become meaningless. The 64-bit counters support the reliable gathering of statistics by SNMP by preventing the wrapping of counter values.
Restrictions
SNMP cannot retrieve 64-bit virtual-circuit (VC) counters.
Related Documents
For information on configuring Frame Relay using Cisco IOS software, refer to the following documents:
•The chapter "Configuring Frame Relay" in the Cisco IOS Wide-Area Networking Configuration Guide, Release 12.2
•The chapter "Frame Relay Commands" in the Cisco IOS Wide-Area Networking Command Reference, Release 12.2
For information on configuring SNMP using Cisco IOS software, see the following documents:
•The chapter "Configuring Simple Network Management Protocol" in the Cisco IOS Configuration Fundamentals Configuration Guide, Release 12.2
•The chapter "SNMP Commands" in the Cisco IOS Configuration Fundamentals Command Reference, Release 12.2
Supported Platforms
•Cisco 7200 series
•Cisco 7500 series (Cisco IOS Release 12.2(4)T3 and later)
Platform Support Through Feature Navigator
Cisco IOS software is packaged in feature sets that support specific platforms. To get updated information regarding platform support for this feature, access Feature Navigator. Feature Navigator dynamically updates the list of supported platforms as new platform support is added for the feature.
Feature Navigator is a web-based tool that enables you to quickly determine which Cisco IOS software images support a specific set of features and which features are supported in a specific Cisco IOS image.
To access Feature Navigator, you must have an account on Cisco.com. If you have forgotten or lost your account information, send a blank e-mail to cco-locksmith@cisco.com. An automatic check will verify that your e-mail address is registered with Cisco.com. If the check is successful, account details with a new random password will be e-mailed to you. Qualified users can establish an account on Cisco.com by following the directions at http://www.cisco.com/register.
Feature Navigator is updated when major Cisco IOS software releases and technology releases occur. As of May 2001, Feature Navigator supports M, T, E, S, and ST releases. You can access Feature Navigator at the following URL:
http://www.cisco.com/go/fn
Supported Standards and MIBs and RFCs
Standards
No new or modified standards are supported by this feature.
MIBs
The frame-relay ifmib-counter64 command modifies the interface MIB (IF-MIB) by allowing slower Frame Relay interfaces and subinterfaces to be included in the 64-bit interface MIB counters.
To obtain lists of supported MIBs by platform and Cisco IOS release, and to download MIB modules, go to the Cisco MIB website on Cisco.com at the following URL:
http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml
RFCs
No new or modified RFCs are supported by this feature.
Prerequisites
This document assumes that you know how to configure Frame Relay and SNMP support using Cisco IOS software.
Configuration Tasks
•Enabling Frame Relay Interfaces for 64-Bit Interface MIB Counters
Enabling Frame Relay Interfaces for 64-Bit Interface MIB Counters
Note This task is supported in Cisco IOS releases 12.0(21)S, 12.3(10), 12.3(11)T, 12.2(18)SXE, and later releases.
Frame Relay interfaces and subinterfaces that have a line speed greater than 20 Mbps are included in the 64-bit interface MIB counters by default. Perform this task to enable Frame Relay interfaces and subinterfaces that have a line speed of less than 20 Mbps to be included in the 64-bit interface MIB counters.
|
|
|
Step 1 |
Router> enable |
Enables privileged EXEC mode. •Enter your password if prompted. |
Step 2 |
Router# configure terminal |
Enters global configuration mode. |
Step 3 |
Router(config)# interface serial interface-number |
Specifies an interface to be configured and enters interface configuration mode. |
Step 4 |
Router(config-if)# encapsulation frame-relay |
Enables Frame Relay encapsulation. |
Step 5 |
Router(config-if)# frame-relay ifmib-counter64 [if | subif] |
Enables Frame Relay interfaces and subinterfaces that have a line speed of less than 20 Mbps to be included in 64-bit interface MIB counters. •This command allows Frame Relay interfaces and subinterfaces that have a line speed of less than 20 Mbps to be included in the following 64-bit interface MIB counters: –ifHCinOctets –ifHCOutOctets –ifHCinUcastPkts –ifHCOutUcastPkts |
Monitoring and Maintaining Frame Relay 64-Bit Counters
To view the values of the Frame Relay 64-bit counters, use the following command in EXEC mode:
|
|
Router# show frame-relay pvc 64-bit [interface interface] [dlci]
|
Displays statistics about permanent virtual circuits (PVCs) for Frame Relay interfaces. |
Configuration Examples
•Enabling Slower Frame Relay Interfaces and Subinterfaces for 64-Bit Interface MIB Counters: Example
•Enabling Only Slower Frame Relay Subinterfaces for 64-Bit Interface MIB Counters: Example
Enabling Slower Frame Relay Interfaces and Subinterfaces for 64-Bit Interface MIB Counters: Example
In the following example, the frame-relay ifmib-counter64 command is used with the if keyword to enable serial interfaces 6/0/1:0, 6/0/2:0, and 6/0/3:0 and related subinterfaces to be included in the 64-bit interface MIB counters. The example also shows corresponding output for the show frame-relay pvc command and the corresponding statistics for the 64-bit interface MIB counters.
ip address 1.1.1.1 255.255.255.0
encapsulation frame-relay
frame-relay interface-dlci 101
no frame-relay inverse-arp
frame-relay ifmib-counter64 if
encapsulation frame-relay
no frame-relay inverse-arp
frame-relay ifmib-counter64 if
interface Serial6/0/2:0.1 point-to-point
ip address 2.1.1.1 255.255.255.0
frame-relay interface-dlci 201
ip address 3.1.1.1 255.255.255.0
encapsulation frame-relay
frame-relay interface-dlci 301
no frame-relay inverse-arp
frame-relay ifmib-counter64 if
interface Serial6/0/3:0.1 point-to-point
ip address 3.1.2.1 255.255.255.0
frame-relay interface-dlci 302
The following example shows corresponding sample output for the show frame-relay pvc command with the 64-bit keyword. Note that the frame-relay ifmib-counter64 command does not affect the output of the show frame-relay pvc command.
Router# show frame-relay pvc 101 64-bit
DLCI = 101, INTERFACE = Serial6/0/1:0
input pkts 231 output pkts 228
in bytes 23604 out bytes 23502
Router# show frame-relay pvc 201 64-bit
DLCI = 201, INTERFACE = Serial6/0/2:0.1
input pkts 1453 output pkts 1408
in bytes 335024 out bytes 327272
Router# show frame-relay pvc 301 64-bit
DLCI = 301, INTERFACE = Serial6/0/3:0
input pkts 510 output pkts 508
in bytes 52690 out bytes 52622
Router# show frame-relay pvc 302 64-bit
DLCI = 302, INTERFACE = Serial6/0/3:0.1
input pkts 957 output pkts 912
in bytes 283246 out bytes 275493
The following output from an SNMP inquiry shows that the 64-bit interface MIB counters include the interfaces configured above:
ifHCInOctets.5 = 0x000000000
ifHCInOctets.16 = 0x000000000
ifHCInOctets.17 = 0x003360d33
ifHCInOctets.18 = 0x000000000
ifHCInOctets.19 = 0x000000000
ifHCInOctets.20 = 0x000000000
ifHCInOctets.24 = 0x000000000
ifHCInOctets.25 = 0x000000000
ifHCInOctets.26 = 0x0001a7afc !! This is serial interface 6/0/1:0
ifHCInOctets.28 = 0x0001a7370 !! This is serial interface 6/0/2:0
ifHCInOctets.34 = 0x00006a45a !! This is serial interface 6/0/3:0
ifHCInOctets.36 = 0x000051cb0 !! This is serial subinterface 6/0/2:0.1
ifHCInOctets.37 = 0x00004526e !! This is serial subinterface 6/0/3:0.1
Enabling Only Slower Frame Relay Subinterfaces for 64-Bit Interface MIB Counters: Example
In the following example, the frame-relay ifmib-counter64 command is used with the subif keyword to enable subinterfaces that are associated with serial interfaces 6/0/1:0, 6/0/2:0, and 6/0/3:0 to be included in the 64-bit interface MIB counters. Slower main interfaces are not included. The example also shows the corresponding statistics for the 64-bit interface MIB counters.
ip address 1.1.1.1 255.255.255.0
encapsulation frame-relay
frame-relay interface-dlci 101
no frame-relay inverse-arp
frame-relay ifmib-counter64 subif
encapsulation frame-relay
no frame-relay inverse-arp
frame-relay ifmib-counter64 subif
interface Serial6/0/2:0.1 point-to-point
ip address 2.1.1.1 255.255.255.0
frame-relay interface-dlci 201
ip address 3.1.1.1 255.255.255.0
encapsulation frame-relay
frame-relay interface-dlci 301
no frame-relay inverse-arp
frame-relay ifmib-counter64 subif
interface Serial6/0/3:0.1 point-to-point
ip address 3.1.2.1 255.255.255.0
frame-relay interface-dlci 302
The following example shows corresponding sample output for the show frame-relay pvc command with the 64-bit keyword. Note that the frame-relay ifmib-counter64 command does not affect the output of the show frame-relay pvc command.
Router# show frame-relay pvc 101 64-bit
DLCI = 101, INTERFACE = Serial6/0/1:0
input pkts 231 output pkts 228
in bytes 23604 out bytes 23502
Router# show frame-relay pvc 201 64-bit
DLCI = 201, INTERFACE = Serial6/0/2:0.1
input pkts 1453 output pkts 1408
in bytes 335024 out bytes 327272
Router# show frame-relay pvc 301 64-bit
DLCI = 301, INTERFACE = Serial6/0/3:0
input pkts 510 output pkts 508
in bytes 52690 out bytes 52622
Router# show frame-relay pvc 302 64-bit
DLCI = 302, INTERFACE = Serial6/0/3:0.1
input pkts 957 output pkts 912
in bytes 283246 out bytes 275493
The following output from an SNMP inquiry shows that the 64-bit interface MIB counters include the subinterfaces configured above:
ifHCInOctets.5 = 0x000000000
ifHCInOctets.16 = 0x000000000
ifHCInOctets.17 = 0x00337a158
ifHCInOctets.18 = 0x000000000
ifHCInOctets.19 = 0x000000000
ifHCInOctets.20 = 0x000000000
ifHCInOctets.24 = 0x000000000
ifHCInOctets.25 = 0x000000000
ifHCInOctets.36 = 0x000051cb0 !! This is serial subinterface 6/0/2:0.1
ifHCInOctets.37 = 0x00004526e !! This is serial subinterface 6/0/3:0.1
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
© 2007 Cisco Systems, Inc. All rights reserved.