Cisco IOS Multiprotocol Label Switching Configuration Guide, Release 12.2SR

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents
Find Matches in This Book
Available Languages
Download Options

Book Title

Cisco IOS Multiprotocol Label Switching Configuration Guide, Release 12.2SR

Chapter Title

MPLS VPN over mGRE

Results

Updated:
February 26, 2010

Chapter: MPLS VPN over mGRE


MPLS VPN over mGRE

First Published: November 20, 2009
Last Updated: September 20, 2011

The MPLS VPN over mGRE feature overcomes the requirement that a carrier support multiprotocol label switching (MPLS) by allowing you to provide MPLS connectivity between networks that are connected by IP-only networks. This allows MPLS label switched paths (LSPs) to use generic routing encapsulation (GRE) tunnels to cross routing areas, autonomous systems, and internet service providers (ISPs). when MPLS VPNs are configured over multipoint GRE (mGRE) you can deploy layer-3 (L3) provider edge (PE) based virtual private network (VPN) services using a standards-based IP core. This allows you to provision the VPN services without using the overlay method.

You can configure mGRE tunnels to create a multipoint tunnel network that overlays an IP backbone. This overlay connects PE routers to transport VPN traffic. In addition, when MPLS VPNs are configured over mGRE you can deploy L3 PE-based VPN services using a standards-based IP core. This allows you to provision the VPN services without using the overlay method. When MPLS VPN over mGRE is configured, the system uses IPv4-based mGRE tunnels to encapsulate VPN-labeled IPv4 and IPv6 packets between PEs.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for MPLS VPN over mGRE" section.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Contents

•Prerequisites for MPLS VPN over mGRE

•Restrictions for MPLS VPN over mGRE

•Information About MPLS VPN over mGRE

•How to Configure MPLS VPN over mGRE

•Configuration Examples for MPLS VPN over mGRE

•Additional References

•Feature Information for MPLS VPN over mGRE

Prerequisites for MPLS VPN over mGRE

Before you configure MPLS VPN with mGRE tunnels, ensure that the MPLS VPN is configured and working properly. See the "Configuring MPLS Layer 3 VPNs" module for information about setting up MPLS VPNs.

Restrictions for MPLS VPN over mGRE

•MPLS VPN over mGRE is supported on the Cisco 7600 series routers using the ES-40 line card and the SIP 400 line card as core facing cards.

•Tunnelled tag traffic must enter the router through a line card that supports MPLS VPN over mGRE.

•Each PE router supports one tunnel configuration only.

•MPLS VPN over mGRE does not support the transportation of multicast traffic between VPNs.

•When a GRE tunnel has the same destination address and source address as the mGRE, the tunnel gets route-cache switched.

•The packets that require fragmentation get route cache-switched.

•When an L3VPN profile is removed and added back, then you should clear the Border Gateway Protocol (BGP) using the clear ip bgp soft command.

•When an mGRE tunnel is created, a dummy tunnel is also created.

•The loopback or IP address used in the update source of the BGP configuration should be the same as that of the transport source of the L3VPN profile.

•mGRE is not stateful switchover (SSO) compliant. However, both mGRE and SSO coexist.

•mGRE and multicast distribution tree (MDT) tunnel should not be configured with the same loopback address.

The limitations for MPLS VPN over mGRE feature are as follows:

–Not all GRE options are supported in the hardware (for example, GRE extended header and GRE key).

–Checking identical VLANs (Internet Control Message Protocol [ICMP] redirect) is not supported on the tunnels.

–Features such as unicast reverse path forwarding (uRPF) and BGP policy accounting are not supported on the tunnels.

Information About MPLS VPN over mGRE

•MPLS VPN over mGRE

MPLS VPN over mGRE

GRE is a point-to-point tunneling protocol where two peers form the endpoints of the tunnel. It is designed to encapsulate network-layer packets inside IP tunneling packets. mGRE is a similar protocol with a single endpoint at one side of the tunnel connected to multiple endpoints at the other side of the tunnel. The mGRE tunnel provides a common link between branch offices that connect to the same VPN. Because mGRE is a point-to-multipoint model, fully meshed GRE tunnels are not required to interconnect MPLS VPN PE devices.

MPLS is a widely deployed VPN internet architecture. MPLS requires that all core routers in the network support MPLS. This feature is useful in networks where the service provider uses a backbone carrier to provide connectivity.

The MPLS VPN over mGRE feature overcomes the requirement of carrier support MPLS by allowing you to provide MPLS connectivity between networks that are connected by IP-only networks. This allows MPLS LSPs to use GRE tunnels to cross routing areas, autonomous systems, and ISPs.

When MPLS VPNs are configured over mGRE you can deploy L3 PE-based VPN services using a standards-based IP core. This allows you to provision the VPN services without using LSP or a Label Distribution Protocol (LDP). The system uses IPv4-based mGRE tunnels to encapsulate VPN-labeled IPv4 and IPv6 packets between PEs.

The MPLS VPN over mGRE feature also allows you to deploy existing MPLS VPN LSP-encapsulated technology concurrently with MPLS VPN over mGRE and enables the system to determine which encapsulation method is used to route specific traffic. The ingress PE router determines which encapsulation technology to use when a packet is sent to the remote PE router.

This section includes information on the following topics on MPLS VPN over mGRE feature:

•Route Maps

•Tunnel Endpoint Discovery and Forwarding

•Tunnel Decapsulation

•Tunnel Source

•IPv6 VPN

Route Maps

By default, VPN traffic is sent using an LSP. The MPLS VPN over mGRE feature uses user-defined route maps to determine which VPN prefixes are reachable over an mGRE tunnel and which VPN prefixes are reachable using an LSP. The route map is applied to advertisements for VPNv4 and VPNv6 address families. The route map uses a next hop tunnel table to determine the encapsulation method for the VPN traffic.

To route traffic over the mGRE tunnel, the system creates an alternative address space that shows that all next hops are reached by encapsulating the traffic in an mGRE tunnel. To configure a specific route to use an mGRE tunnel, the user adds an entry for that route to the route map. The new entry remaps the Network Layer Reachability Information (NLRI) of the route to the alternative address space. If there is no remap entry in the route map for a route, then traffic on that route is forwarded over an LSP.

When the user configures MPLS VPN over mGRE, the system automatically provisions the alternative address space, normally held in the tunnel-encapsulated virtual routing and forwarding (VRF) instance. To ensure that all traffic reachable through the address space is encapsulated in an mGRE tunnel, the system installs a single default route out of a tunnel. The system also creates a default tunnel on the route map. The user can attach this default route map to the appropriate BGP updates.

Tunnel Endpoint Discovery and Forwarding

In order for the MPLS VPN over mGRE feature to function correctly, the system must be able to discover the remote PEs in the system and construct tunnel forwarding information for these remote PEs. In addition the system must be able to detect when a remote PE is no longer valid and remove the tunnel forwarding information for that PE.

If an ingress PE receives a VPN advertisement over BGP, it uses the route target attributes (which it inserts into the VRF) and the MPLS VPN label from the advertisement, to associate the prefixes with the appropriate customer. The next hop of the inserted route is set to the NLRI of the advertisement.

The advertised prefixes contain information about remote PEs in the system (in the form of NLRIs), and the PE uses this information to notify the system when an NLRI becomes active or inactive. The system uses this notification to update the PE forwarding information.

When the system receives notification of a new remote PE, it adds the information to the tunnel endpoint database, which causes the system to create an adjacency associated with the tunnel interface. The adjacency description includes information on the encapsulation and other processing that the system must perform to send encapsulated packets to the new remote PE.

The adjacency information is placed into the tunnel encapsulated VRF. When a user remaps a VPN NLRI to a route in the VRF (using the route map), the system links the NLRI to the adjacency; therefore the VPN is linked to a tunnel.

Tunnel Decapsulation

When the egress PE receives a packet from a tunnel interface that uses the MPLS VPN over mGRE feature, the PE decapsulates the packet to create a VPN label tagged packet, and sends the packet to the MPLS forwarding (MFI) code.

Tunnel Source

The MPLS VPN over mGRE feature uses a single tunnel configured as an mGRE tunnel to configure a system with a large number of endpoints (remote PEs). To identify the origin of tunnel-encapsulated packets, the system uses the tunnel source information.

At the transmitting (ingress) PE, when a VPN packet is sent to a tunnel, the tunnel destination is the NLRI. At a receiving (egress) PE, the tunnel source is the address that the packets encapsulated in the mGRE tunnel are received on. Therefore, at the egress PE the packet destination must match the NLRI from the local PE.

IPv6 VPN

If the advertising PE router has an IPv6 address then the NLRI must also be an IPv6 address (regardless of the network between the PEs). If the network between the PEs is IPv4 based, the system creates the IPv6 address of the advertising PE using an IPv4 mapped address in the following form: ::FFFF:IPv4-PE-address. The receiving PE sets the next hop for the VPN tag IPv6 prefixes to the IPv4 address embedded in the IPv6 NLRI. This enables the PE to link VPNv6 traffic to an LSP or an mGRE tunnel in the same way it maps VPNv4 traffic.

When a PE receives VPNv6 updates, it applies the IPv6 route map. The MPLS VPN over mGRE feature uses the IPv6 route map to set the next hop information in the Tunnel_Encap VRF.

How to Configure MPLS VPN over mGRE

To deploy MPLS VPN over mGRE tunnels, you create a VRF instance, enable and configure L3 VPN encapsulation, link the route map to the application template, and set up the BGP VPNv4 and VPNv6 exchange so that updates are filtered through the route map.

The configuration steps to deploy MPLS VPN over mGRE are described in the following sections:

•Configuring an L3VPN Encapsulation Profile (required)

•Configuring BGP and Route Maps (required)

Configuring an L3VPN Encapsulation Profile

This section describes how to configure an L3VPN encapsulation profile.

Note Transport protocols such as IPv6, MPLS, IP, and Layer 2 Tunneling Protocol version 3 (L2TPv3) can also be used in this configuration.

SUMMARY STEPS

1. enable

2. configure terminal

3. l3vpn encapsulation ip profile-name

4. transport ipv4 [source interface-type interface-number]

5. protocol gre [key gre-key]

6. end

7. show l3vpn encapsulation ip profile-name

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

l3vpn encapsulation ip profile-name

Example:

Router(config)# l3vpn encapsulation ip tunnel encap

Enters L3 VPN encapsulation configuration mode to create the tunnel.

Step 4 

transport ipv4 [source interface-type interface-number]

Example:

Router(config-l3vpn-encap-ip)# transport ipv4 source loopback 0

(Optional) Specifies IPv4 transport source mode and defines the transport source interface.

•If you use the transport ipv4 source interface-type interface-number command, make sure that the specified source address is used as the next hop in BGP updates advertised by the PE.

•If you do not use this command, the bgp update source or bgp next-hop command is automatically used as the tunnel source.

Step 5 

protocol gre [key gre-key]

Example:

Router(config-l3vpn-encap-ip)# protocol gre key 1234

Specifies GRE as the tunnel mode and sets the GRE key.

Step 6 

end

Example:

Router(config-l3vpn-encap-ip)# end

Exits L3 VPN encapsulation configuration mode and returns to privileged EXEC mode.

Step 7 

show l3vpn encapsulation ip profile-name

Example:

Router# show l3vpn encapsulation ip tunnel encap

(Optional) Displays the profile health and the underlying tunnel interface.


Configuring BGP and Route Maps

Perform this task to configure BGP and route maps. The following steps also enable you to link the route map to the application template and set up the BGP VPNv4 and VPNv6 exchange so that the updates are filtered through the route map.

SUMMARY STEPS

1. enable

2. configure terminal

3. router bgp as-number

4. bgp log-neighbor-changes

5. neighbor ip-address remote-as as-number

6. neighbor ip-address update-source interface-name interface-number

7. address-family ipv4

8. no synchronization

9. redistribute connected

10. neighbor ip-address activate

11. no auto-summary

12. exit

13. address-family vpnv4

14. neighbor ip-address activate

15. neighbor ip-address send-community both

16. neighbor ip-address route-map map-name in

17. exit

18. address-family vpnv6

19. neighbor ip-address activate

20. neighbor ip-address send-community both

21. neighbor ip-address route-map map-name in

22. exit

23. route-map map-tag permit position

24. set ip next-hop encapsulate l3vpn profile-name

25. set ipv6 next-hop encapsulate l3vpn profile-name

26. exit

27. exit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

router bgp as-number

Example:

Router(config)# router bgp 100

Specifies the number of an autonomous system that identifies the router to other BGP routers and tags the routing information passed along, and enters router configuration mode.

Step 4 

bgp log-neighbor-changes

Example:

Router(config-router)# bgp log-neighbor-changes

Enables logging of BGP neighbor resets.

Step 5 

neighbor ip-address remote-as as-number

Example:

Router(config-router)# neighbor 209.165.200.225 remote-as 100

Adds an entry to the BGP or multiprotocol BGP neighbor table.

Step 6 

neighbor ip-address update-source interface name

Example:

Router(config-router)# neighbor 209.165.200.225 update-source loopback 0

Allows BGP sessions to use any operational interface for TCP connections.

Step 7 

address-family ipv4

Example:

Router(config-router)# address-family ipv4

Enters address family configuration mode to configure routing sessions that use IPv4 address prefixes.

Step 8 

no synchronization

Example:

Router(config-router-af)# no synchronization

Enables the Cisco IOS software to advertise a network route without waiting for an IGP.

Step 9 

redistribute connected

Example:

Router(config-router-af)# redistribute connected

Redistributes routes from one routing domain into another routing domain and allows the target protocol to redistribute routes learned by the source protocol and connected prefixes on those interfaces over which the source protocol is running.

Step 10 

neighbor ip-address activate

Example:

Router(config-router-af)# neighbor 209.165.200.225 activate

Enables the exchange of information with a BGP neighbor.

Step 11 

no auto-summary

Example:

Router(config-router-af)# no auto-summary

Disables automatic summarization and sends subprefix routing information across classful network boundaries.

Step 12 

exit

Example:

Router(config-router-af)# exit

Exits address family configuration mode.

Step 13 

address-family vpnv4

Example:

Router(config-router)# address-family vpnv4

Enters address family configuration mode to configure routing sessions, such as BGP, that use standard VPNv4 address prefixes.

Step 14 

neighbor ip-address activate

Example:

Router(config-router-af)# neighbor 209.165.200.225 activate

Enables the exchange of information with a BGP neighbor.

Step 15 

neighbor ip-address send-community both

Example:

Router(config-router-af)# neighbor 209.165.200.225 send-community both

Specifies that a communities attribute, for both standard and extended communities, should be sent to a BGP neighbor.

Step 16 

neighbor ip-address route-map map-name in

Example:

Router(config-router-af)# neighbor 209.165.200.225 route-map SELECT_UPDATE_FOR_L3VPN in

Applies the named route map to the incoming route.

Step 17 

exit

Example:

Router(config-router-af)# exit

Exits address family configuration mode.

Step 18 

address-family vpnv6

Example:

Router(config-router)# address-family vpnv6

Enters address family configuration mode to configure routing sessions, such as BGP, that use VPNv6 address prefixes.

Step 19 

neighbor ip-address activate

Example:

Router(config-router-af)# neighbor 209.165.200.252 activate

Enables the exchange of information with a BGP neighbor.

Step 20 

neighbor ip-address send-community both

Example:

Router(config-router-af)# neighbor 209.165.200.252 send-community both

Specifies that a communities attribute, for both standard and extended communities, should be sent to a BGP neighbor.

Step 21 

neighbor ip-address route-map map-name in

Example:

Router(config-router-af)# neighbor 209.165.200.252 route-map SELECT_UPDATE_FOR_L3VPN in

Applies the named route map to the incoming route.

Step 22 

exit

Example:

Router(config-router-af)# exit

Exits address family configuration mode.

Step 23 

route-map map-tag permit position

Example:

Router(config-router)# route-map SELECT_UPDATE_FOR_L3VPN permit 10

Enters route-map configuration mode and defines the conditions for redistributing routes from one routing protocol into another.

•The redistribute router configuration command uses the specified map tag to reference this route map. Multiple route maps may share the same map tag name.

•If the match criteria are met for this route map, the route is redistributed as controlled by the set actions.

•If the match criteria are not met, the next route map with the same map tag is tested. If a route passes none of the match criteria for the set of route maps sharing the same name, it is not redistributed by that set.

•The position argument indicates the position a new route map will have in the list of route maps already configured with the same name.

Step 24 

set ip next-hop encapsulate l3vpn profile-name

Example:

Router(config-route-map)# set ip next-hop encapsulate l3vpn my profile

Indicates that output IPv4 packets that pass a match clause of the route map are sent to the VRF for tunnel encapsulation.

Step 25 

set ipv6 next-hop encapsulate l3vpn profile-name

Example:

Router(config-route-map)# set ip next-hop encapsulate l3vpn tunnel encap

Indicates that output IPv6 packets that pass a match clause of the route map are sent to the VRF for tunnel encapsulation.

Step 26 

exit

Example:

Router(config-route-map)# exit

Exits route-map configuration mode and enters global configuration mode.

Step 27 

exit

Example:

Router(config)# exit

Exits global configuration mode.


Configuration Examples for MPLS VPN over mGRE

•Example: Verifying The MPLS VPN over mGRE Configuration

•Example: Configuration Sequence For MPLS VPN over mGRE

Example: Verifying The MPLS VPN over mGRE Configuration

Use the following examples to verify that the configuration is working properly:

Cisco Express Forwarding (CEF) Switching

You can verify that CEF switching is working as expected: 

Router# show ip cef vrf Customer_A tunnel 0

 
   
 
    
   
 
    
209.165.200.250/24

 
   
 
    
   
 
    
    nexthop 209.165.200.251 Tunnel0 label 16

 
   
 
    
   
 Endpoint Creation 
 
    
   
 You can verify the tunnel endpoint that has been created: 
 
    
   
 
    
Router# show tunnel endpoints tunnel 0              

 
   
 
    
   
 
    
 
   
 
    
   
 
    
 Tunnel0 running in multi-GRE/IP mode

 
   
 
    
   
 
    
 
   
 
    
   
 
    
 Endpoint transport 209.165.200.251 Refcount 3 Base 0x2AE93F0 Create Time 00:00:42

 
   
 
    
   
 
    
   overlay 209.165.200.254 Refcount 2 Parent 0x2AE93F0 Create Time 00:00:42

 
   
 
    
   
 Adjacency 
 
    
   
 You can verify that the corresponding adjacency has been created: 
 
    
   
 
    
Router# show adjacency tunnel 0

 
   
 
    
   
 
    
 
   
 
    
   
 
    
   Protocol Interface                 Address

 
   
 
    
   
 
    
  IP       Tunnel0                   209.165.200.251(4)

 
   
 
    
   
 
    
  TAG      Tunnel0                   209.165.200.251(3)

 
   
 
    
    
   
 Profile Health 
 
    
   
 You can use show l3vpn encapsulation profile-name command to get information on the basic state of the application. The output of this command provides you details on the references to the underlying tunnel. 
 
    
   
 
    
Router# show l3vpn encapsulation ip tunnel encap

 
   
 
    
   
 
    
 
   
 
    
   
 
    
	Profile: tunnel encap

 
   
 
    
   
 
    
	transport ipv4 source Auto: Loopback0

 
   
 
    
   
 
    
	protocol gre

 
   
 
    
   
 
    
  	Tunnel Tunnel0 Created [OK]

 
   
 
    
   
 
    
  	Tunnel Linestate [OK]

 
   
 
    
   
 
    
  	Tunnel Transport Source (Auto) Loopback0 [OK]

 
   
 
     
    
    
   
 Example: Configuration Sequence For MPLS VPN over mGRE 
 
    
   
 This example shows the configuration sequence for MPLS VPN over mGRE: 
 
    
   
 
    
vrf definition Customer A

 
   
 
    
   
 
    
 rd 100:110

 
   
 
    
   
 
    
 route-target export 100:1000

 
   
 
    
   
 
    
 route-target import 100:1000

 
   
 
    
   
 
    
 !

 
   
 
    
   
 
    
 address-family ipv4

 
   
 
    
   
 
    
 exit-address-family

 
   
 
    
   
 
    
 !

 
   
 
    
   
 
    
 address-family ipv6

 
   
 
    
   
 
    
 exit-address-family

 
   
 
    
   
 
    
!

 
   
 
    
   
 
    
!

 
   
 
    
   
 
    
ip cef

 
   
 
    
   
 
    
!

 
   
 
    
   
 
    
ipv6 unicast-routing

 
   
 
    
   
 
    
ipv6 cef

 
   
 
    
   
 
    
!

 
   
 
    
   
 
    
!

 
   
 
    
   
 
    
l3vpn encapsulation ip sample profile name 

 
   
 
    
   
 
    
 transport source loopback 0 

 
   
 
    
   
 
    
 protocol gre key 1234 

 
   
 
    
   
 
    
!

 
   
 
    
   
 
    
!

 
   
 
    
   
 
    
 interface Loopback0

 
   
 
    
   
 
    
  ip address 209.165.200.252 255.255.255.224

 
   
 
    
   
 
    
  ip router isis 

 
   
 
    
   
 
    
!

 
   
 
    
   
 
    
interface Serial2/0

 
   
 
    
   
 
    
 vrf forwarding Customer A

 
   
 
    
   
 
    
 ip address 209.165.200.253 255.255.255.224

 
   
 
    
   
 
    
 ipv6 address 3FFE:1001::/64 eui-64

 
   
 
    
   
 
    
 no fair-queue

 
   
 
    
   
 
    
 serial restart-delay 0

 
   
 
    
   
 
    
! 

 
   
 
    
   
 
    
router bgp 100

 
   
 
    
   
 
    
 bgp log-neighbor-changes

 
   
 
    
   
 
    
 neighbor 209.165.200.254 remote-as 100

 
   
 
    
   
 
    
 neighbor 209.165.200.254 update-source Loopback0

 
   
 
    
   
 
    
 !

 
   
 
    
   
 
    
 address-family ipv4

 
   
 
    
   
 
    
  no synchronization

 
   
 
    
   
 
    
  redistribute connected

 
   
 
    
   
 
    
  neighbor 209.165.200.254 activate

 
   
 
    
   
 
    
  no auto-summary

 
   
 
    
   
 
    
 exit-address-family

 
   
 
    
   
 
    
 !

 
   
 
    
   
 
    
 address-family vpnv4

 
   
 
    
   
 
    
  neighbor 209.165.200.254 activate

 
   
 
    
   
 
    
  neighbor 209.165.200.254 send-community both

 
   
 
    
   
 
    
  neighbor 209.165.200.254 route-map SELECT_UPDATE_FOR_L3VPN in

 
   
 
    
   
 
    
 exit-address-family

 
   
 
    
   
 
    
 !

 
   
 
    
   
 
    
 address-family vpnv6

 
   
 
    
   
 
    
  neighbor 209.165.200.254 activate

 
   
 
    
   
 
    
  neighbor 209.165.200.254 send-community both

 
   
 
    
   
 
    
  neighbor 209.165.200.254 route-map SELECT_UPDATE_FOR_L3VPN in

 
   
 
    
   
 
    
 exit-address-family

 
   
 
    
   
 
    
 !

 
   
 
    
   
 
    
 address-family ipv4 vrf Customer A

 
   
 
    
   
 
    
  no synchronization

 
   
 
    
   
 
    
  redistribute connected

 
   
 
    
   
 
    
 exit-address-family

 
   
 
    
   
 
    
 !

 
   
 
    
   
 
    
 address-family ipv6 vrf Customer A

 
   
 
    
   
 
    
  redistribute connected

 
   
 
    
   
 
    
  no synchronization

 
   
 
    
   
 
    
 exit-address-family

 
   
 
    
   
 
    
!

 
   
 
    
   
 
    
!

 
   
 
    
   
 
    
route-map SELECT_UPDATE_FOR_L3VPN permit 10

 
   
 
    
   
 
    
set ip next-hop encapsulate sample profile name 

 
   
 
    
   
 
    
set ipv6 next-hop encapsulate sample profile name 

 
   
 
     
    
    
   
 Additional References 
 
     
    
    
   
 Related Documents
 
   
 
    
 
      
      
      
 
        
        

          Related Topic 
        
 		 
        
        

          Document Title 
        
 		 
      
 
      
 
       
 Configuring MPLS Layer 3 VPNs 
 		 
       
 Cisco IOS Multiprotocol Label Switching Configuration Guide 
 		 
      
 
      
 
       
 Dynamic Layer 3 VPNs with multipoint GRE tunnels 
 		 
       
 Cisco IOS Interface and Hardware Component Configuration Guide 
 		 
      
 
      
 
       
 Cisco Express Forwarding 
 		 
       
 Cisco IOS IP Switching Configuration Guide 
 		 
      
 
      
 
       
 Generic routing encapsulation 
 		 
       
 Cisco IOS Interface and Hardware Component Configuration Guide 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
     
    
   
 Standards
 
   
 
    
 
      
      
      
 
        
        

          Standard 
        
 		 
        
        

          Title 
        
 		 
      
 
      
 
       
 None 
 		 
       
 — 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
     
    
   
 MIBs
 
   
 
    
 
      
      
      
 
        
        

          MIB 
        
 		 
        
        

          MIBs Link 
        
 		 
      
 
      
 
       
 IETF-PPVPN-MPLS-VPN-MIB 
 		 
       
 To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL: 
 
 http://www.cisco.com/go/mibs 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
     
    
   
 RFCs
 
   
 
    
 
      
      
      
 
        
        

          RFC 
        
 		 
        
        

          Title 
        
 		 
      
 
      
 
       
 RFC 2547 
 		 
       
 BGP/MPLS VPNs 
 		 
      
 
      
 
       
 RFC 2784 
 		 
       
 Generic Routing Encapsulation (GRE) 
 		 
      
 
      
 
       
 RFC 2890 
 		 
       
 Key Sequence Number Extensions to GRE 
 		 
      
 
      
 
       
 RFC 4023 
 		 
       
 Encapsulating MPLS in IP or Generic Routing Encapsulation 
 		 
      
 
      
 
       
 RFC 4364 
 		 
       
 BGP/MPLS IP Virtual Private Networks (VPNs) 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
     
    
   
 Technical Assistance
 
   
 
    
 
      
      
      
 
        
        

          Description 
        
 		 
        
        

          Link 
        
 		 
      
 
      
 
       
 The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies. 
 
 To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds. 
 
 Access to most tools on the Cisco Support website requires a Cisco.com user ID and password. 
 		 
       
 http://www.cisco.com/cisco/web/support/index.html 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
     
    
    
   
 Feature Information for MPLS VPN over mGRE 
 
    
   
 Table 1 lists the release history for this feature. 
 
    
   
 Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which Cisco software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required. 
 
   
 
     
   
 
   
 
    
   
 Note Table 1 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature. 
 
   
 
    
   
 
 
   
 
    
 
      
       
       
      
 Table 1 Feature Information for MPLS VPN over mGRE  
 
      
      
      
 
        
        

          Feature Name 
        
 		 
        
        

          Releases 
        
 		 
        
        

          Feature Information 
        
 		 
      
 
      
 
       
 MPLS VPN over mGRE 
 		 
       
 12.2(33)SRE
15.1(2)T
15.0(1)SY 
 		 
       
 This feature provides support to carry MPLS Layer 3 VPN traffic over mGRE. This feature also supports SIP-400 and ES-40 on Cisco 7600 series routers. 
 
 The following sections provide information about this feature: 
 
 •Configuring an L3VPN Encapsulation Profile 
 
 •Configuring BGP and Route Maps 
 
 The following commands were introduced or modified by this feature: l3vpn encapsulation ip, protocol gre, show l3vpn encapsulation ip, transport ipv4, set ip next-hop, set ipv6 next-hop. 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
    
    
   
 Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R) 
 
    
    
    
   
 Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2009-2011 Cisco Systems, Inc. All rights reserved. 
 
    
   


 
 
    

    

        

















    

        

    
    
    




















  
Was this Document Helpful?

  
    
    
  
  
      
      FeedbackFeedback
  






			
    

	

















  
    
  



    

			
    

	
















    
Contact Cisco