qos_plcshp_xe

Finding Feature Information
Contents
Prerequisites for Distribution of Remaining Bandwidth Using Ratio
Restrictions for Distribution of Remaining Bandwidth Using Ratio
Information About Distribution of Remaining Bandwidth Using Ratio
- Benefits of the Distribution of Remaining Bandwidth Using Ratio Feature
- Bandwidth-Remaining Ratio Functionality
How to Configure Distribution of Remaining Bandwidth Using Ratio
- Configuring and Applying Bandwidth-Remaining Ratios to Subinterfaces
  - Restrictions
- Configuring and Applying Bandwidth-Remaining Ratios to Class Queues
Configuration Examples for Distribution of Remaining Bandwidth Using Ratio
Additional References
Feature Information for Distribution of Remaining Bandwidth Using Ratio

Distribution of Remaining Bandwidth Using Ratio

First Published: December 10, 2007

Last Updated: March 23, 2011

The Distribution of Remaining Bandwidth Using Ratio feature allows service providers to configure a bandwidth-remaining ratio on subinterfaces and class queues. This ratio specifies the relative weight of a subinterface or queue with respect to other subinterfaces or queues. During congestion, the router uses this bandwidth-remaining ratio to determine the amount of excess bandwidth (unused by priority traffic) to allocate to a class of nonpriority traffic. The router allocates excess bandwidth relative to the other subinterface-level queues and class queues configured on the physical interface. By administration of a bandwidth-remaining ratio, traffic priority is not based solely on speed. Instead, the service provider can base priority on alternative factors such as service product and subscription rate.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for Distribution of Remaining Bandwidth Using Ratio" section.

Use Cisco Feature Navigator to find information about platform support and Cisco IOS XE Software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

•Prerequisites for Distribution of Remaining Bandwidth Using Ratio

•Restrictions for Distribution of Remaining Bandwidth Using Ratio

•Information About Distribution of Remaining Bandwidth Using Ratio

•How to Configure Distribution of Remaining Bandwidth Using Ratio

•Configuration Examples for Distribution of Remaining Bandwidth Using Ratio

•Additional References

•Feature Information for Distribution of Remaining Bandwidth Using Ratio

Prerequisites for Distribution of Remaining Bandwidth Using Ratio

Before enabling the Distribution of Remaining Bandwidth Using Ratio feature, create as many traffic classes as you need by using the class-map command.

Restrictions for Distribution of Remaining Bandwidth Using Ratio

•Bandwidth-remaining ratios can be used on outbound interfaces only.

•The bandwidth remaining ratio command cannot coexist with another bandwidth command in different traffic classes of the same policy map. For example, the following configuration is not valid and causes an error message to display:

policy-map Prec1

 class precedence_0

  bandwidth remaining ratio 10

 class precedence_2

  bandwidth 1000

•The bandwidth remaining ratio command cannot coexist with another bandwidth command in the same class. For example, the following configuration is not valid and causes an error message to display:

policy-map Prec1

 class precedence_0

  bandwidth 1000

  bandwidth remaining ratio 10

•The bandwidth remaining ratio command cannot coexist with the priority command in the same class. For example, the following configuration is not valid and causes an error message to display:

policy-map Prec1

 class precedence_1

  priority percent 10

  bandwidth remaining ratio 10

Information About Distribution of Remaining Bandwidth Using Ratio

To configure the Distribution of Remaining Bandwidth Using Ratio feature, you should understand the following concepts:

•Benefits of the Distribution of Remaining Bandwidth Using Ratio Feature

•Bandwidth-Remaining Ratio Functionality

Benefits of the Distribution of Remaining Bandwidth Using Ratio Feature

The Distribution of Remaining Bandwidth Using Ratio feature allows service providers to prioritize subscriber traffic during periods of congestion. A bandwidth-remaining ratio is used to influence how the router allocates excess bandwidth (unused by priority traffic) to a class of nonpriority traffic. Instead of using only bandwidth rate, the router considers configured minimum bandwidth rates, maximum bandwidth rates, and bandwidth-remaining ratios when determining excess bandwidth allocation. A bandwidth-remaining ratio adds more flexibility in prioritizing traffic and enables you to influence excess bandwidth allocation by basing the bandwidth-remaining ratio on factors other than speed.

With bandwidth-remaining ratios, service providers have more flexibility in assigning priority to subinterfaces and queues during congestion. In addition to speed, you can base the bandwidth-remaining ratio on alternative factors, such as a service product or subscription rate. In this way, for example, you can give higher weight to subinterfaces that carry business services and lower weight to subinterfaces that carry residential services.

Bandwidth-Remaining Ratio Functionality

A bandwidth-remaining ratio, specified by the bandwidth remaining ratio command, is a value from 1 to 1000 that is used to determine the amount of unused (excess) bandwidth to allocate to a class-level queue or subinterface-level queue during congestion. The router allocates the excess bandwidth relative to the other class-level queues and subinterface-level queues configured on the physical interface. The bandwidth-remaining ratio value does not indicate a percentage. As the name implies, a ratio is used. For example, a subinterface with a bandwidth-remaining ratio of 100 receives 10 times the unused (excess) bandwidth during congestion than a subinterface with a bandwidth-remaining ratio of 10.

Without bandwidth-remaining ratios, the queueing mechanism or scheduler on the router allocates unused (excess) bandwidth equally among the classes or subinterfaces.

With bandwidth-remaining ratios, unused (excess) bandwidth allocation can be based on factors other than the bandwidth rate (for example, the service product or the subscription rate).

Using the bandwidth remaining ratio command, the bandwidth-remaining ratio can be configured differently on each subinterface or class. The bandwidth-remaining ratio can range from 1 to 1000. For example, if there are three subscribers, and the bandwidth-remaining ratios are configured as 9, 7, and 1, and if after priority traffic is served, there are 1700 kbps of excess bandwidth, the subscribers get 900 kbps, 700 kbps, and 100 kbps, respectively.

How to Configure Distribution of Remaining Bandwidth Using Ratio

You can apply bandwidth-remaining ratios to subinterfaces and/or classes queues.

•Configuring and Applying Bandwidth-Remaining Ratios to Subinterfaces

•Configuring and Applying Bandwidth-Remaining Ratios to Class Queues

Configuring and Applying Bandwidth-Remaining Ratios to Subinterfaces

Restrictions

You can apply bandwidth-remaining ratios to outbound subinterfaces only.

SUMMARY STEPS

1. enable

2. configure terminal

3. policy-map child-policy-name

4. class class-map-name

5. bandwidth bandwidth-kbps

6. Repeat Steps 4 and 5 to configure additional traffic classes, if needed.

7. exit

8. exit

9. policy-map parent-policy-name

10. class class-default

11. bandwidth remaining ratio ratio

12. shape {average | peak} cir [bc] [be]

13. service-policy child-policy-name

14. exit

15. exit

16. interface type slot/module/port.subinterface [point-to-point | multipoint]

17. service-policy output parent-policy-name

18. end

DETAILED STEPS


	Command or Action	Purpose
Step 1	enable Example: Router> enable	Enables privileged EXEC mode. •Enter your password if prompted.
Step 2	configure terminal Example: Router# configure terminal	Enters global configuration mode.
Step 3	policy-map child-policy-name Example: Router(config)# policy-map Child	Creates or modifies a child policy map and enters policy-map configuration mode. •Enter the name of the child policy map.
Step 4	class class-map-name Example: Router(config-pmap)# class precedence_0	Configures the class map and enters policy-map class configuration mode. •Enter the name of a previously created class map. See the "Prerequisites for Distribution of Remaining Bandwidth Using Ratio" section.
Step 5	bandwidth bandwidth-kbps Example: Router(config-pmap-c)# bandwidth 10000	Specifies the bandwidth, in kbps, to be allocated to this traffic class. •Enter the amount of bandwidth, in kilobits per second (kbps).
Step 6	Repeat Steps 4 and 5 to configure additional traffic classes, if needed.
Step 7	exit Example: Router(config-pmap-c)# exit	Exits policy-map class configuration mode.
Step 8	exit Example: Router(config-pmap)# exit	Exits policy-map configuration mode.
Step 9	policy-map parent-policy-name Example: Router(config)# policy-map Parent	Creates or modifies a parent policy map and enters policy-map configuration mode. •Enter the name of the parent policy map.
Step 10	class class-default Example: Router(config-pmap)# class class-default	Configures the class-default class and enters policy-map class configuration mode. Note The router interprets any features that are configured under the class-default class as aggregate features on the subinterface.
Step 11	bandwidth remaining ratio ratio Example: Router(config-pmap-c)# bandwidth remaining ratio 10	Specifies the bandwidth-remaining ratio for the subinterface. •Enter the ratio. The ratio is the value used to determine the amount of unused bandwidth to allocate to each queue on the subinterface during periods of congestion. The scheduler allocates the excess bandwidth relative to other subinterfaces. Valid values are 1 to 1000. The default value is 1.
Step 12	shape {average \| peak} cir [bc] [be] Example: Router(config-pmap-c)# shape average 100000000	(Optional) Shapes the average or peak rate to the rate that you specify. •Enter either the average or peak keyword along with the CIR and any optional arguments. Note the following: –average—Specifies average-rate shaping. –peak—Specifies peak-rate shaping. –cir—Specifies the committed information rate (CIR), in bits per second (bps). –(Optional) bc—Specifies the committed burst size, in bits. –(Optional) be—Specifies the excess burst size, in bits.
Step 13	service-policy child-policy-name Example: Router(config-pmap-c)# service-policy Child	Applies the child policy map that you specify to the traffic class. •Enter the name of the previously configured child policy map. The router applies the QoS actions (features) specified in the child policy map to the traffic class. Note The service-policy command typically requires that you specify the direction of the traffic using the input or output keywords. However, when applying a child policy to a parent policy, do not specify a traffic direction.
Step 14	exit Example: Router(config-pmap-c)# exit	Exits policy-map class configuration mode.
Step 15	exit Example: Router(config-pmap)# exit	Exits policy-map configuration mode.
Step 16	interface type slot/module/port.subinterface [point-to-point \| multipoint] Example: Router(config)# interface GigabitEthernet 1/0/0.1	Creates or modifies the interface that you specify and enters subinterface configuration mode. •Enter the interface type. Note the following: –type—Specifies the interface type (for example, Gigabit Ethernet). –slot/module/port.subinterface—Specifies the number of the subinterface that identifies the subinterface (for example, 1/0/0.1). –(Optional) point-to-point—Indicates that the subinterface is a point-to-point subinterface. –(Optional) multipoint—Indicates that the subinterface is a point-to-multipoint subinterface.
Step 17	service-policy output parent-policy-name Example: Router(config-subif)# service-policy output Parent	Applies the parent policy map to the subinterface. •Enter the output keyword and the name of the parent policy map. Note The router shapes the subinterface traffic to the shaping rate specified in the parent class-default class and applies the QoS actions (features) specified in the child policy map. Note During periods of congestion, the router uses the bandwidth-remaining ratio specified in the parent policy map to allocate unused bandwidth on this subinterface relative to other subinterfaces.
Step 18	end Example: Router(config-subif)# end	Returns to privileged EXEC mode.

Configuring and Applying Bandwidth-Remaining Ratios to Class Queues

SUMMARY STEPS

1. enable

2. configure terminal

3. policy-map child-policy-name

4. class class-map-name

5. shape {average | peak} cir [bc] [be]

6. bandwidth remaining ratio ratio

7. Repeat Steps 4, 5, and 6 for each class queue that you want to define, specifying the bandwidth-remaining ratio as applicable.

8. exit

9. exit

10. policy-map parent-policy-name

11. class class-default

12. shape {average | peak} cir [bc] [be]

13. bandwidth remaining ratio ratio

14. service-policy child-policy-name

15. exit

16. exit

17. interface type slot/module/port.subinterface [point-to-point | multipoint]

18. service-policy output parent-policy-name

19. end

DETAILED STEPS


	Command or Action	Purpose
Step 1	enable Example: Router> enable	Enables privileged EXEC mode. •Enter your password if prompted.
Step 2	configure terminal Example: Router# configure terminal	Enters global configuration mode.
Step 3	policy-map child-policy-name Example: Router(config)# policy-map Child	Creates or modifies a child policy map and enters policy-map configuration mode. •Enter the name of the child policy map.
Step 4	class class-map-name Example: Router(config-pmap)# class precedence_0	Configures the class map and enters policy-map class configuration mode. •Enter the name of the previously created class map. See the "Prerequisites for Distribution of Remaining Bandwidth Using Ratio" section.
Step 5	shape {average \| peak} cir [bc] [be] Example: Router(config-pmap-c)# shape average 100000000	(Optional) Shapes the average or peak rate to the rate that you specify. •Enter either the average or peak keyword along with the CIR and any optional arguments. Note the following: –average—Specifies average-rate shaping. –peak—Specifies peak-rate shaping. –cir—Specifies the committed information rate (CIR), in bits per second (bps). –(Optional) bc—Specifies the committed burst size, in bits. –(Optional) be—Specifies the excess burst size, in bits.
Step 6	bandwidth remaining ratio ratio Example: Router(config-pmap-c)# bandwidth remaining ratio 10	Specifies the bandwidth-remaining ratio for the traffic class. •Enter the bandwidth-remaining ratio. The ratio is the value used to determine the amount of unused bandwidth to allocate to each queue on the subinterface during periods of congestion. The queueing mechanism or scheduler allocates the excess bandwidth relative to other subinterfaces. Valid values are 1 to 1000. The default value is 1. Note In a hierarchical policy map structure, the bandwidth remaining ratio ratio command must be used for at least one class. Using it in other classes is optional. When this command is not explicitly enabled in the other classes, the queueing mechanism uses 1 as the default.
Step 7	Repeat Steps 4, 5, and 6 for each class queue that you want to define, specifying the bandwidth-remaining ratio as applicable.
Step 8	exit Example: Router(config-pmap-c)# exit	Exits policy-map class configuration mode.
Step 9	exit Example: Router(config-pmap)# exit	Exits policy-map configuration mode.
Step 10	policy-map parent-policy-name Example: Router(config)# policy-map Parent	Creates or modifies a parent policy map and enters policy-map configuration mode. •Enter the name of the parent policy map.
Step 11	class class-default Example: Router(config-pmap)# class class-default	Configures the class-default class and enters policy-map class configuration mode. Note The router interprets any features that are configured under the class-default class as aggregate features on the subinterface.
Step 12	shape {average \| peak} cir [bc] [be] Example: Router(config-pmap-c)# shape average 100000000	(Optional) Shapes the average or peak rate to the rate that you specify. •Enter either the average or peak keyword along with the CIR and any optional arguments. Note the following: –average—Specifies average-rate shaping. –peak—Specifies peak-rate shaping. –cir—Specifies the committed information rate (CIR), in bits per second (bps). –(Optional) bc—Specifies the committed burst size, in bits. –(Optional) be—Specifies the excess burst size, in bits.
Step 13	bandwidth remaining ratio ratio Example: Router(config-pmap-c)# bandwidth remaining ratio 10	(Optional for class-default or other classes in a hierarchical policy map structure) Specifies the bandwidth-remaining ratio for the subinterface. •Enter the bandwidth-remaining ratio. The ratio is the value used to determine the amount of unused bandwidth to allocate to each queue on the subinterface during periods of congestion. The queueing mechanism or scheduler allocates the excess bandwidth relative to other subinterfaces. Valid values are 1 to 1000. The default value is 1. Note In a hierarchical policy map structure, the bandwidth remaining ratio ratio command must be used for at least one class. Using it in other classes is optional. When this command is not explicitly enabled in the other classes, the queueing mechanism uses 1 as the default.
Step 14	service-policy child-policy-name Example: Router(config-pmap-c)# service-policy Child	Applies the child policy map that you specify to the traffic class. •Enter the name of the child policy map. The router applies the QoS actions (features) specified in the child policy map to the traffic class. Note The service-policy command typically requires that you specify the direction of the traffic using the input or output keywords. However, when applying a child policy map to a parent policy map, do not specify traffic direction.
Step 15	exit Example: Router(config-pmap-c)# exit	Exits policy-map class configuration mode.
Step 16	exit Example: Router(config-pmap)# exit	Exits policy-map configuration mode.
Step 17	interface type slot/module/port.subinterface [point-to-point \| multipoint] Example: Router(config)# interface GigabitEthernet 1/0/0.1	Creates or modifies the interface that you specify and enters subinterface configuration mode. •Enter the interface type. Note the following: –type—Specifies the interface type (for example, Gigabit Ethernet). –slot/module/port.subinterface—Specifies the number of the subinterface that identifies the subinterface (for example, 1/0/0.1). –(Optional) point-to-point—Indicates that the subinterface is a point-to-point subinterface. –(Optional) multipoint—Indicates that the subinterface is a point-to-multipoint subinterface.
Step 18	service-policy output parent-policy-name Example: Router(config-subif)# service-policy output Parent	Attaches the parent policy map to the subinterface. •Enter the output keyword and the name of the parent policy map. Note When congestion occurs, the class queues receive bandwidth according to the specified class-level bandwidth-remaining ratios.
Step 19	end Example: Router(config-subif)# end	Returns to privileged EXEC mode.

Configuration Examples for Distribution of Remaining Bandwidth Using Ratio

This section contains the following examples:

•Example: Configuring Bandwidth-Remaining Ratios on Ethernet Subinterfaces

•Example: Verifying Bandwidth-Remaining Ratios on Class Queues

•Example: Verifying Bandwidth Remaining Ratios

Example: Configuring Bandwidth-Remaining Ratios on Ethernet Subinterfaces

The following example shows how to configure bandwidth-remaining ratios on an Ethernet subinterface using a hierarchical policy. In the example, Gigabit Ethernet subinterface 1/0/0.1 is shaped to 100 Mbps. During congestion, the router uses the bandwidth-remaining ratio of 10 to determine the amount of excess bandwidth (unused by priority traffic) to allocate to the nonpriority traffic on subinterface 1/0/0.1, relative to the other subinterface-level and class-level queues on the interface.

policy-map Child

 class precedence_0

  bandwidth 10000

 class precedence_1

  shape average 100000

  bandwidth 100

policy-map Parent

 class class-default

  bandwidth remaining ratio 10

  shape average 100000000

  service-policy Child

interface GigabitEthernet1/0/0.1

 encapsulation dot1Q 100

 ip address 10.1.0.1 255.255.255.0

 service-policy output Parent

Example: Verifying Bandwidth-Remaining Ratios on Class Queues

In the following sample configuration, vlan10_policy is applied on the Gigabit Ethernet subinterface 1/0/0.10 and vlan20_policy is applied on the Gigabit Ethernet subinterface 1/0/0.20. During congestion on the interface, subinterface Gigabit Ethernet 1/0/0.20 has 10 times more available bandwidth than subinterface Gigabit Ethernet 1/0/0.10 because the bandwidth-remaining ratio for subinterface Gigabit Ethernet 1/0/0.20 is 10 times more than the bandwidth-remaining ratio for subinterface 1/0/0.10: 100 on subinterface 1/0/0.20 and 10 on subinterface 1/0/0.10.

When congestion occurs within a subinterface level, the class queues receive bandwidth according to the class-level bandwidth-remaining ratios. In the example, the bandwidth for classes precedence_0, precedence_1, and precedence_2 is allocated based on the bandwidth-remaining ratios of the classes: 20, 40, and 60, respectively.

Router# show policy-map

Policy Map child-policy

    Class precedence_0

      Average Rate Traffic Shaping

      cir 500000 (bps)

      bandwidth remaining ratio 20 <---- Class-level ratio

    Class precedence_1

      Average Rate Traffic Shaping

      cir 500000 (bps)

      bandwidth remaining ratio 40 <---- Class-level ratio

    Class precedence_2

      Average Rate Traffic Shaping

      cir 500000 (bps)

      bandwidth remaining ratio 60 <---- Class-level ratio

Policy Map vlan10_policy

    Class class-default

      Average Rate Traffic Shaping

      cir 1000000 (bps)

      bandwidth remaining ratio 10 <---- Subinterface-level ratio

      service-policy child-policy

Policy Map vlan20_policy

    Class class-default

      Average Rate Traffic Shaping

      cir 1000000 (bps)

      bandwidth remaining ratio 100 <---- Subinterface-level ratio

      service-policy child-policy

interface GigabitEthernet1/0/0.10

 encapsulation dot1Q 10

 snmp trap link-status

 service-policy output vlan10_policy

interface GigabitEthernet1/0/0.20

 encapsulation dot1Q 20

 snmp trap link-status

 service-policy output vlan20_policy

Example: Verifying Bandwidth Remaining Ratios

The following sample output from the show policy-map interface command indicates that bandwidth-remaining ratios are configured on class-level queues in the policy maps named vlan10_policy and child-policy, which are attached to Gigabit Ethernet subinterface 1/0/0.10.

Router# show policy-map interface GigabitEthernet 1/0/0.10

GigabitEthernet1/0/0.10

  Service-policy output: vlan10_policy

    Class-map: class-default (match-any)

      0 packets, 0 bytes

      5 minute offered rate 0 bps, drop rate 0 bps

      Match: any

      Queueing

      queue limit 64 packets

      (queue depth/total drops/no-buffer drops) 0/0/0

      (pkts output/bytes output) 0/0

      shape (average) cir 1000000, bc 4000, be 4000

      target shape rate 1000000

      bandwidth remaining ratio 10

      Service-policy : child-policy

        Class-map: precedence_0 (match-all)

          0 packets, 0 bytes

          5 minute offered rate 0 bps, drop rate 0 bps

          Match: ip precedence 0

          Queueing

          queue limit 64 packets

          (queue depth/total drops/no-buffer drops) 0/0/0

          (pkts output/bytes output) 0/0

          shape (average) cir 500000, bc 2000, be 2000

          target shape rate 500000

          bandwidth remaining ratio 20

        Class-map: precedence_1 (match-all)

          0 packets, 0 bytes

          5 minute offered rate 0 bps, drop rate 0 bps

          Match: ip precedence 1

          Queueing

          queue limit 64 packets

          (queue depth/total drops/no-buffer drops) 0/0/0

          (pkts output/bytes output) 0/0

          shape (average) cir 500000, bc 2000, be 2000

          target shape rate 500000

          bandwidth remaining ratio 40

        Class-map: precedence_2 (match-all)

          0 packets, 0 bytes

          5 minute offered rate 0 bps, drop rate 0 bps

          Match: ip precedence 2

          Queueing

          queue limit 64 packets

          (queue depth/total drops/no-buffer drops) 0/0/0

          (pkts output/bytes output) 0/0

          shape (average) cir 500000, bc 2000, be 2000

          target shape rate 500000

          bandwidth remaining ratio 60

        Class-map: class-default (match-any)

          0 packets, 0 bytes

          5 minute offered rate 0 bps, drop rate 0 bps

          Match: any

          queue limit 64 packets

          (queue depth/total drops/no-buffer drops) 0/0/0

          (pkts output/bytes output) 0/0

The following sample output from the show policy-map interface command indicates that bandwidth-remaining ratios are configured on class-level queues in the policy maps named vlan20_policy and child-policy, which are attached to Gigabit Ethernet subinterface 1/0/0.20.

Router# show policy-map interface GigabitEthernet 1/0/0.20

GigabitEthernet1/0/0.20

  Service-policy output: vlan20_policy

    Class-map: class-default (match-any)

      0 packets, 0 bytes

      5 minute offered rate 0 bps, drop rate 0 bps

      Match: any

      Queueing

      queue limit 64 packets

      (queue depth/total drops/no-buffer drops) 0/0/0

      (pkts output/bytes output) 0/0

      shape (average) cir 1000000, bc 4000, be 4000

      target shape rate 1000000

      bandwidth remaining ratio 100

      Service-policy : child-policy

        Class-map: precedence_0 (match-all)

          0 packets, 0 bytes

          5 minute offered rate 0 bps, drop rate 0 bps

          Match: ip precedence 0

          Queueing

          queue limit 64 packets

          (queue depth/total drops/no-buffer drops) 0/0/0

          (pkts output/bytes output) 0/0

          shape (average) cir 500000, bc 2000, be 2000

          target shape rate 500000

          bandwidth remaining ratio 20

        Class-map: precedence_1 (match-all)

          0 packets, 0 bytes

          5 minute offered rate 0 bps, drop rate 0 bps

          Match: ip precedence 1

          Queueing

          queue limit 64 packets

          (queue depth/total drops/no-buffer drops) 0/0/0

          (pkts output/bytes output) 0/0

          shape (average) cir 500000, bc 2000, be 2000

          target shape rate 500000

          bandwidth remaining ratio 40

        Class-map: precedence_2 (match-all)

          0 packets, 0 bytes

          5 minute offered rate 0 bps, drop rate 0 bps

          Match: ip precedence 2

          Queueing

          queue limit 64 packets

          (queue depth/total drops/no-buffer drops) 0/0/0

          (pkts output/bytes output) 0/0

          shape (average) cir 500000, bc 2000, be 2000

          target shape rate 500000

          bandwidth remaining ratio 60

        Class-map: class-default (match-any)

          0 packets, 0 bytes

          5 minute offered rate 0 bps, drop rate 0 bps

          Match: any

          queue limit 64 packets

          (queue depth/total drops/no-buffer drops) 0/0/0

          (pkts output/bytes output) 0/0

The following sample output from the show policy-map command indicates that a bandwidth-remaining ratio of 10 is configured on the parent class-default class of the policy map named vlan10_policy.

Router# show policy-map vlan10_policy

  Policy Map vlan10_policy

    Class class-default

      Average Rate Traffic Shaping

      cir 1000000 (bps)

      bandwidth remaining ratio 10

      service-policy child-policy

The following sample output from the show policy-map command indicates that a bandwidth-remaining ratio of 100 is configured on the parent class-default class of the policy map named vlan20_policy.

Router# show policy-map vlan20_policy

  Policy Map vlan20_policy

    Class class-default

      Average Rate Traffic Shaping

      cir 1000000 (bps)

      bandwidth remaining ratio 100

      service-policy child-policy

The following sample output from the show policy-map command indicates that bandwidth-remaining ratios of 20, 40, and 60 are configured on the class queues precedence_0, precedence_1, and precedence_2, respectively.

Router# show policy-map child-policy

  Policy Map child-policy

    Class precedence_0

      Average Rate Traffic Shaping

      cir 500000 (bps)

      bandwidth remaining ratio 20

    Class precedence_1

      Average Rate Traffic Shaping

      cir 500000 (bps)

      bandwidth remaining ratio 40

    Class precedence_2

      Average Rate Traffic Shaping

      cir 500000 (bps)

      bandwidth remaining ratio 60

Additional References

Related Topic	Document Title
QoS commands: complete command syntax, command modes, command history, defaults, usage guidelines, and examples	Cisco IOS Quality of Service Solutions Command Reference
Congestion avoidance	"Congestion Avoidance Overview" module
Class maps, policy maps, hierarchical policy maps, Modular Quality of Service Command-Line Interface (CLI) (MQC)	"Applying QoS Features Using the MQC" module
Traffic shaping, traffic policing	"Policing and Shaping Overview" module

Standards


Standard	Title
No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.	—

MIBs


MIB	MIBs Link
No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.	To locate and download MIBs for selected platforms, Cisco IOS XE Software releases, and feature sets, use Cisco MIB Locator found at the following URL: http://www.cisco.com/go/mibs

RFCs


RFC	Title
No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature.	—

Technical Assistance


Description	Link
The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.	http://www.cisco.com/cisco/web/support/index.html

Feature Information for Distribution of Remaining Bandwidth Using Ratio

Table 1 lists the release history for this feature.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which Cisco IOS XE Software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Note Table 1 lists only the Cisco IOS XE Software release that introduced support for a given feature in a given Cisco IOS XE Software release train. Unless noted otherwise, subsequent releases of that Cisco IOS XE Software release train also support that feature.

Table 1 Feature Information for Distribution of Remaining Bandwidth Using Ratio
Feature Name	Releases	Feature Information
MQC—Distribution of Remaining Bandwidth Using Ratio	Cisco IOS XE Release 2.1	The Distribution of Remaining Bandwidth Using Ratio feature allows service providers to configure a bandwidth-remaining ratio on subinterfaces and class queues. This ratio specifies the relative weight of a subinterface or queue with respect to other subinterfaces or queues. During congestion, the router uses this bandwidth-remaining ratio to determine the amount of excess bandwidth (unused by priority traffic) to allocate to a class of nonpriority traffic. In Cisco IOS XE Release 2.1, this feature was introduced on Cisco ASR 1000 Series Routers. The following commands were introduced or modified: bandwidth remaining ratio, show policy-map, show policy-map interface.

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2011 Cisco Systems, Inc. All rights reserved.

Was this Document Helpful?

Feedback

Contact Cisco

Open a Support Case
(Requires a Cisco Service Contract)

Bias-Free Language

Results

Chapter: Distribution of Remaining Bandwidth Using Ratio

Distribution of Remaining Bandwidth Using Ratio

Finding Feature Information

Contents

Prerequisites for Distribution of Remaining Bandwidth Using Ratio

Restrictions for Distribution of Remaining Bandwidth Using Ratio

Information About Distribution of Remaining Bandwidth Using Ratio

Benefits of the Distribution of Remaining Bandwidth Using Ratio Feature

Bandwidth-Remaining Ratio Functionality

How to Configure Distribution of Remaining Bandwidth Using Ratio

Configuring and Applying Bandwidth-Remaining Ratios to Subinterfaces

Restrictions

SUMMARY STEPS

DETAILED STEPS

Configuring and Applying Bandwidth-Remaining Ratios to Class Queues

SUMMARY STEPS

DETAILED STEPS

Configuration Examples for Distribution of Remaining Bandwidth Using Ratio

Example: Configuring Bandwidth-Remaining Ratios on Ethernet Subinterfaces

Example: Verifying Bandwidth-Remaining Ratios on Class Queues

Example: Verifying Bandwidth Remaining Ratios

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Feature Information for Distribution of Remaining Bandwidth Using Ratio

Was this Document Helpful?

Contact Cisco