OSPF Inbound Filtering Using Route Maps with a Distribute List
Last Updated: May 4, 2009
The OSPF Inbound Filtering Using Route Maps with a Distribute List feature allows users to define a route map to prevent Open Shortest Path First (OSPF) routes from being added to the routing table. In the route map, the user can match on any attribute of the OSPF route.
Finding Feature Information
For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see "Feature Information for OSPF Inbound Filtering Using Route Maps with a Distribute List" section.
Use Cisco Feature Navigator to find information about platform support and Cisco IOS XE software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.
Contents
•Prerequisites OSPF Inbound Filtering Using Route Maps with a Distribute List
•Information About OSPF Inbound Filtering Using Route Maps with a Distribute List
•How to Configure OSPF Inbound Filtering Using Route Maps
•Configuration Examples for OSPF Inbound Filtering Using Route Maps with a Distribute List
•Additional References
•Feature Information for OSPF Inbound Filtering Using Route Maps with a Distribute List
Prerequisites OSPF Inbound Filtering Using Route Maps with a Distribute List
It is presumed that you have OSPF configured in your network.
Information About OSPF Inbound Filtering Using Route Maps with a Distribute List
Benefits of OSPF Route-Map-Based-Filtering
Users can define a route map to prevent OSPF routes from being added to the routing table. This filtering happens at the moment when OSPF is installing the route in the routing table. This feature has no effect on LSA flooding. In the route map, the user can match on any attribute of the OSPF route. That is, the route map could be based on the following match options:
•match interface
•match ip address
•match ip next-hop
•match ip route-source
•match metric
•match route-type
•match tag
This feature can be useful during redistribution if the user tags prefixes when they get redistributed on ASBRs and later uses the tag to filter the prefixes from being installed in the routing table on other routers.
Filtering Based on Route Tag
Users can assign tags to external routes when they are redistributed to OSPF. Then the user can deny or permit those routes in the OSPF domain by identifying that tag in the route-map and distribute-list in commands.
Filtering Based on Route Type
In OSPF, the external routes could be Type 1 or Type 2. Users can create route maps to match either Type 1 or Type 2 and then use the distribute-list in command to filter certain prefixes. Also, route maps can identify internal routes (interarea and intra-area) and then those routes can be filtered.
Filtering Based on Route Source
When a match is done on the route source, the route source represents the OSPF Router ID of the LSA originator of the LSA in which the prefix is advertised.
Filtering Based on Interface
When a match is done on the interface, the interface represents the outgoing interface for the route that OSPF is trying to install in the routing table.
Filtering Based on Next-Hop
When a match is done on the next hop, the next hop represents the next hop for the route that OSPF is trying to install in the routing table.
How to Configure OSPF Inbound Filtering Using Route Maps
Configuring OSPF Inbound Filtering Using a Route Map
SUMMARY STEPS
1. enable
2. configure terminal
3. route-map map-tag [permit | deny] [sequence-number]
4. match tag tag-name
or other match commands.
5. Repeat Steps 3 and 4 with other route-map and match commands if you choose.
6. exit
7. router ospf process-id
8. distribute-list route-map map-tag in
9. end
DETAILED STEPS
|
|
|
Step 1 |
enable
Router> enable |
Enables privileged EXEC mode. •Enter your password if prompted. |
Step 2 |
configure terminal
Router# configure terminal |
Enters global configuration mode. |
Step 3 |
route-map map-tag [permit | deny] [sequence-number]
Router(config)# route-map tag-filter deny 10 |
Defines a route map to control filtering. |
Step 4 |
match tag tag-name
or other match commands
Router(config-router)# match tag 777 |
Matches routes with a specified name, to be used as the route map is referenced. •At least one match command is required, but it need not be this match command. This is just an example. •The list of match commands available to be used in this type of route map appears on the distribute-list in command reference page. •This type of route map will have no set commands. |
Step 5 |
Repeat Steps 3 and 4 with other route-map and match commands if you choose. |
— |
Step 6 |
exit
Router(config-router)# exit |
Exits router configuration mode. |
Step 7 |
router ospf process-id
Router(config)# router ospf 1 |
Configures an OSPF routing process. |
Step 8 |
distribute-list route-map map-tag in
Router(config-router)# distribute-list route-map tag-filter in |
Enables filtering based on an OSPF route map. |
Step 9 |
end
Router(config-router)# end |
Exits router configuration mode. |
Configuration Examples for OSPF Inbound Filtering Using Route Maps with a Distribute List
Example: OSPF Route-Map-Based Filtering
In this example, OSPF external LSAs have a tag. The value of the tag is examined before the prefix is installed in the routing table. All OSPF external prefixes that have the tag value of 777 are filtered (prevented from being installed in the routing table). The permit statement with sequence number 20 has no match conditions, and there are no other route-map statements after sequence number 20, so all other conditions are permitted.
route-map tag-filter deny 10
route-map tag-filter permit 20
network 172.16.2.1 0.0.0.255 area 0
distribute-list route-map tag-filter in
Additional References
The following sections provide references related to configuring the OSPF Inbound Filtering Using Route Maps with a Distribute List feature.
Related Documents
Standards
|
|
No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature. |
— |
MIBs
|
|
No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature. |
To locate and download MIBs for selected platforms, Cisco IOS XE software releases, and feature sets, use Cisco MIB Locator found at the following URL: http://www.cisco.com/go/mibs |
RFCs
|
|
No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature. |
— |
Technical Assistance
|
|
The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password. |
http://www.cisco.com/cisco/web/support/index.html |
Feature Information for OSPF Inbound Filtering Using Route Maps with a Distribute List
Table 1 lists the release history for this feature.
Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which Cisco IOS XE software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.
Note Table 1 lists only the Cisco IOS XE software release that introduced support for a given feature in a given Cisco IOS XE software release train. Unless noted otherwise, subsequent releases of that Cisco IOS XE software release train also support that feature.
Table 1 Feature Information for OSPF Inbound Filtering Using Route Maps with a Distribute List
|
|
|
OSPF Inbound Filtering Using Route Maps with a Distribute List |
Cisco IOS XE Release 2.1 |
The OSPF Inbound Filtering Using Route Maps with a Distribute List feature allows users to define a route map to prevent OSPF routes from being added to the routing table. The following commands are introduced or modified in the feature documented in this module: •distribute-list in (IP) |
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
© 2011 Cisco Systems, Inc. All rights reserved.