- Read Me First
- MPLS Traffic Engineering and Enhancements
- MPLS Traffic Engineering Configurable Path Calculation Metric for Tunnels
- MPLS Traffic Engineering--Scalability Enhancements
- MPLS Traffic Engineering--LSP Attributes
- MPLS Traffic Engineering AutoTunnel Mesh Groups
- MPLS Traffic Engineering Verbatim Path Support
- MPLS Traffic Engineering--RSVP Hello State Timer
- MPLS Traffic Engineering Forwarding Adjacency
- MPLS Traffic Engineering Class-based Tunnel Selection
- MPLS Traffic Engineering Interarea Tunnels
- MPLS Traffic Engineering Static IPv6 Routes over MPLS TE IPv4 Tunnels
- MPLS Traffic Engineering Automatic Bandwidth Adjustment for TE Tunnels
- MPLS Traffic Engineering – Bundled Interface Support
- RSVP Refresh Reduction and Reliable Messaging
- Finding Feature Information
- Prerequisites for MPLS Traffic Engineering--Scalability Enhancements
- Restrictions for MPLS Traffic Engineering--Scalability Enhancements
- Information About MPLS Traffic Engineering--Scalability Enhancements
- Scalability Enhancements for Traffic Engineering Tunnels
- RSVP Rate Limiting
- Improved Recovery Response for Signaling and Management of MPLS Traffic Engineering Tunnels
- IS-IS and MPLS Traffic Engineering Topology Database Interactions
- Improved Counter Capabilities for MPLS TE Tunnels Events and RSVP Signaling
- Benefits of MPLS Traffic Engineering--Scalability Enhancements
- How to Configure MPLS Traffic Engineering--Scalability Enhancements
- Configuration Examples for MPLS Traffic Engineering--Scalability Enhancements
- Additional References
- Feature Information for MPLS Traffic Engineering Scalability Enhancements
- Glossary
MPLS Traffic Engineering--Scalability Enhancements
The MPLS Traffic Engineering--Scalability Enhancement feature improves scalability performance for large numbers of traffic engineering tunnels.
These improvements allow an increase in the number of traffic engineering (TE) tunnels a router can support when the router is configured as a tunnel headend. Additionally, when the router is configured as a tunnel midpoint, the enhancements reduce the time required to establish large numbers of TE tunnels.
This feature module contains information about and instructions on how to configure the Multiprotocol Label Switching (MPLS) traffic engineering scalability enhancements.
- Finding Feature Information
- Prerequisites for MPLS Traffic Engineering--Scalability Enhancements
- Restrictions for MPLS Traffic Engineering--Scalability Enhancements
- Information About MPLS Traffic Engineering--Scalability Enhancements
- How to Configure MPLS Traffic Engineering--Scalability Enhancements
- Configuration Examples for MPLS Traffic Engineering--Scalability Enhancements
- Additional References
- Feature Information for MPLS Traffic Engineering Scalability Enhancements
- Glossary
Finding Feature Information
Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Prerequisites for MPLS Traffic Engineering--Scalability Enhancements
Your network must support the following Cisco IOS XE features before you enable MPLS traffic engineering:
MPLS
Cisco Express Forwarding
Intermediate System-to-Intermediate System (IS-IS) or Open Shortest Path First (OSPF)
Restrictions for MPLS Traffic Engineering--Scalability Enhancements
The number of tunnels that a particular platform can support can vary depending on:
The types of interfaces that the tunnels traverse
The manner in which the Resource Reservation Protocol (RSVP) message pacing feature is configured
MPLS traffic engineering supports only a single IGP process/instance. Multiple IGP processes/instances are not supported and MPLS traffic engineering should not be configured in more than one IGP process/instance.
Information About MPLS Traffic Engineering--Scalability Enhancements
- Scalability Enhancements for Traffic Engineering Tunnels
- RSVP Rate Limiting
- Improved Recovery Response for Signaling and Management of MPLS Traffic Engineering Tunnels
- IS-IS and MPLS Traffic Engineering Topology Database Interactions
- Improved Counter Capabilities for MPLS TE Tunnels Events and RSVP Signaling
- Benefits of MPLS Traffic Engineering--Scalability Enhancements
Scalability Enhancements for Traffic Engineering Tunnels
Scalability performance is improved for large numbers of traffic engineering tunnels, and includes the following enhancements:
Increase the number of traffic engineering tunnels a router can support when configured as a tunnel headend and when configured as a tunnel midpoint
Reduce the time required to establish large numbers of traffic engineering tunnels
RSVP Rate Limiting
A burst of RSVP traffic engineering signaling messages can overflow the input queue of a receiving router, causing some messages to be dropped. Dropped messages cause a substantial delay in completing label switched path (LSP) signaling.
This MPLS Traffic Engineering--Scalability Enhancements feature provides an enhancement mechanism that controls the transmission rate for RSVP messages and reduces the likelihood of input drops on the receiving router. The default transmission rate is 200 RSVP messages per second to a given neighbor. The rate is configurable.
Improved Recovery Response for Signaling and Management of MPLS Traffic Engineering Tunnels
The MPLS Traffic Engineering--Scalability Enhancements feature improves the recovery response for signaling and management of MPLS TE tunnels. LSP recovery responsiveness is improved when a link used by an LSP fails:
When the upstream end of a failed link detects the failure, the software generates an RSVP No Route path error message. This enables the LSP headend to detect the link failure and initiate recovery, even when the Interior Gateway Protocol (IGP) update announcing the link failure is delayed.
The LSP headend marks the link in question so that subsequent constraint-based shortest path first (SPF) calculations ignore the link until either a new IGP update arrives or a configurable timeout occurs. This ensures that resignaling to restore the LSP avoids the failed link.
IS-IS and MPLS Traffic Engineering Topology Database Interactions
The MPLS Traffic Engineering--Scalability Enhancements feature reduces the interval between when the IS-IS protocol receives an IGP update and when it delivers the update to the MPLS traffic engineering topology database.
Before the MPLS Traffic Engineering--Scalability Enhancements feature was introduced, when IS-IS received a new LSP that contained traffic engineering type, length, value (TLV) objects, a delay of several seconds could occur before IS-IS passed the traffic engineering TLVs to the traffic engineering database. The purpose of the delay was to provide better scalability during periods of network instability and to give the router an opportunity to receive more fragments of the LSP before passing the information to the traffic engineering database. However, this delay increased the convergence time for the traffic engineering database.
With the MPLS Traffic Engineering--Scalability Enhancements feature, IS-IS extracts traffic engineering TLVs from received LSPs and passes them to the traffic engineering database immediately. The exception to this occurs when there are large numbers of LSPs to process and it is important to limit CPU consumption, such as during periods of network instability. The parameters that control IS-IS delivery of traffic engineering TLVs to the traffic engineering topology database are configurable.
![]() Note | MPLS traffic engineering supports only a single IGP process/instance. Multiple IGP processes/instances are not supported and MPLS traffic engineering should not be configured in more than one IGP process/instance. |
Improved Counter Capabilities for MPLS TE Tunnels Events and RSVP Signaling
With the MPLS Traffic Engineering--Scalability Enhancements feature, diagnostic and troubleshooting capabilities for MPLS traffic engineering tunnels and RSVP are improved:
Counters record tunnel headend error events such as no route (link down), preemption, and insufficient bandwidth on a per-tunnel basis.
Counters record RSVP messages. The counters are per-interface and record the number of RSVP messages of each type sent and received on the interface.
Benefits of MPLS Traffic Engineering--Scalability Enhancements
The MPLS Traffic Engineering--Scalability Enhancements feature provides the following benefits:
Increased scalability--Up to 600 MPLS traffic engineering tunnel headends are supported. Up to 10,000 traffic engineering tunnel midpoints are supported, with up to 5000 midpoints per interface.
Faster recovery after failure conditions--Message pacing provides a mechanism to throttle RSVP control messages so that they are less likely to be dropped. This results in a faster recovery from failure conditions when many MPLS traffic engineering tunnels are being set up.
Improved reroute time--When a traffic engineering tunnel is down, the headend router needs to be notified so that it can signal for a new LSP for the tunnel along an alternate path. The headend router does not have to wait for an IGP update to signal for a new LSP for the tunnel along an alternate path.
Improved tunnel setup time--Fewer control messages and tunnel setup messages are dropped. This reduces the average time required to set up tunnels.
How to Configure MPLS Traffic Engineering--Scalability Enhancements
- Enabling RSVP Rate Limiting for MPLS Traffic Engineering Scalability Enhancements
- Managing Link Failure Timeouts for MPLS Traffic Engineering Tunnels
- Controlling IS-IS Communication with the MPLS Traffic Engineering Topology Database
- Monitoring and Maintaining MPLS TE Scalability Enhancements
Enabling RSVP Rate Limiting for MPLS Traffic Engineering Scalability Enhancements
Perform the following task to enable RSVP rate limiting for MPLS traffic engineering scalability enhancements. RSVP rate limiting maintains, on an outgoing interface basis, a count of messages that were dropped because the output queue for the interface used for rate limiting was full.
1.
enable
2.
configure
terminal
3.
ip
rsvp
signalling
rate-limit
[burst number] [limit number] [maxsize bytes] [period ms]
4.
end
5.
show
ip
rsvp
neighbor
DETAILED STEPS
Managing Link Failure Timeouts for MPLS Traffic Engineering Tunnels
Perform this task to manage link failure timeouts for MPLS traffic engineering tunnels.
This allows the configuration of a timeout during which the router ignores a link in its path calculation to avoid paths that contain a failed link and are likely to fail when signaled.
1.
enable
2.
configure
terminal
3.
mpls
traffic-eng
topology
holddown
sigerr
seconds
4.
end
5.
show
mpls
traffic-eng
topology
[brief]
DETAILED STEPS
Controlling IS-IS Communication with the MPLS Traffic Engineering Topology Database
Perform the following task to control IS-IS and MPLS traffic engineering topology database interactions. This reduces the interval time between when the IS-IS protocol receives an IGP update and when IS-IS delivers the update to the MPLS traffic engineering topology database, which reduces convergence time for the database.
![]() Note | MPLS traffic engineering supports only a single IGP process/instance. Multiple IGP processes/instances are not supported and MPLS traffic engineering should not be configured in more than one IGP process/instance. |
1.
enable
2.
configure
terminal
3.
router
isis
[area-tag]
4.
mpls
traffic-eng
scanner
[interval seconds] [max-flash LSPs]
5.
end
DETAILED STEPS
Monitoring and Maintaining MPLS TE Scalability Enhancements
1.
enable
2.
show
ip
rsvp
neighbor
[detail]
3.
show
ip
rsvp
counters
[summary]
4.
clear
ip
rsvp
counters
5.
clear
ip
rsvp
signalling
rate-limit
6.
show
mpls
traffic-eng
tunnels
statistics
7.
clear
mpls
traffic-eng
tunnels
counters
8.
show
mpls
traffic-eng
topology
[brief]
9.
exit
DETAILED STEPS
Step 1 |
enable
Use this command to enable privileged EXEC mode. Enter your password if prompted. For example: Example: Router> enable Router# |
Step 2 |
show
ip
rsvp
neighbor
[detail] Use this command to verify that RSVP message pacing is turned on. For example: Example: Router# show ip rsvp neighbor detail Neighbor:10.0.0.1 Encapsulation:RSVP Rate-Limiting: Dropped messages:0 Refresh Reduction: Remote epoch:0x1BFEA5 Out of order messages:0 Retransmitted messages:0 Highest rcvd message id:1059 Last rcvd message:00:00:04 Neighbor:10.0.0.2 Encapsulation:RSVP Rate-Limiting: Dropped messages:0 Refresh Reduction: Remote epoch:0xB26B1 Out of order messages:0 Retransmitted messages:0 Highest rcvd message id:945 Last rcvd message:00:00:05 |
Step 3 |
show
ip
rsvp
counters
[summary] Use this command to display the counts of RSVP messages that were sent and received. For example: Example: Router# show ip rsvp counters summary All Interfaces Recv Xmit Recv Xmit Path 110 15 Resv 50 28 PathError 0 0 ResvError 0 0 PathTear 0 0 ResvTear 0 0 ResvConf 0 0 RTearConf 0 0 Ack 0 0 Srefresh 0 0 Hello 5555 5554 IntegrityChalle 0 0 IntegrityRespon 0 0 DSBM_WILLING 0 0 I_AM_DSBM 0 0 Unknown 0 0 Errors 0 0 Recv Msg Queues Current Max RSVP 0 2 Hello (per-I/F) 0 1 Awaiting Authentication 0 0 |
Step 4 |
clear
ip
rsvp
counters
Use this command to clear (set to zero) all IP RSVP counters that are being maintained. For example: Example: Router# clear ip rsvp counters Clear rsvp counters [confirm] |
Step 5 |
clear
ip
rsvp
signalling
rate-limit
Use this command to clear (set to zero) counts of the messages that message pacing was forced to drop because the output queue for the interface used for message pacing was full. For example: Example: Router# clear ip rsvp signalling rate-limit |
Step 6 |
show
mpls
traffic-eng
tunnels
statistics
Use this command to display event counters for one or more MPLS traffic engineering tunnels. For example: Example: Router# show mpls traffic-eng tunnels statistics Tunnel1001 (Destination 10.8.8.8; Name Router_t1001) Management statistics: Path: 25 no path, 1 path no longer valid, 0 missing ip exp path 5 path changes State: 3 transitions, 0 admin down, 1 oper down Signalling statistics: Opens: 2 succeeded, 0 timed out, 0 bad path spec 0 other aborts Errors: 0 no b/w, 0 no route, 0 admin 0 bad exp route, 0 rec route loop, 0 other . . . Example: Tunnel7050 (Destination 10.8.8.8; Name Router_t7050) Management statistics: Path: 19 no path, 1 path no longer valid, 0 missing ip exp path 3 path changes State: 3 transitions, 0 admin down, 1 oper down Signalling statistics: Opens: 2 succeeded, 0 timed out, 0 bad path spec 0 other aborts Errors: 0 no b/w, 0 no route, 0 admin 0 bad exp route, 0 rec route loop, 0 other |
Step 7 |
clear
mpls
traffic-eng
tunnels
counters
Use this command to clear counters for all MPLS traffic engineering tunnels. For example: Example: Router# clear mpls traffic-eng tunnels counters Clear traffic engineering tunnel counters [confirm] |
Step 8 |
show
mpls
traffic-eng
topology
[brief] Use this command to display the MPLS traffic engineering topology database. For example: Example: Router# show mpls traffic-eng topology brief My_System_id:0000.0000.0003.00 (isis level-2) Signalling error holddown:10 sec Global Link Generation 9 IGP Id:0000.0000.0003.00, MPLS TE Id:10.0.3.1 Router Node (isis level-2) link[0]:Point-to-Point, Nbr IGP Id:0000.0000.0004.00, nbr_node_id:2, gen:9 frag_id 0, Intf Address:10.0.0.33, Nbr Intf Address:10.0.0.34 TE metric:10, IGP metric:10, attribute_flags:0x0 SRLGs:1 2 |
Step 9 |
exit
Use this command to exit to user EXEC mode. For example: Example: Router# exit Router> |
Configuration Examples for MPLS Traffic Engineering--Scalability Enhancements
- Example Enabling RSVP Rate Limiting for MPLS Traffic Engineering Scalability Enhancements
- Example Managing Link Failure Timeouts for MPLS Traffic Engineering Tunnels
- Example Controlling IS-IS Communication with the MPLS Traffic Engineering Topology Database
Example Enabling RSVP Rate Limiting for MPLS Traffic Engineering Scalability Enhancements
The following examples show how to enable RSVP rate limiting for MPLS traffic engineering scalability enhancements:
configure terminal ip rsvp signalling rate-limit end
The following is sample output that traffic engineering displays when RSVP rate limiting is enabled:
Router# show ip rsvp signalling rate-limit Rate Limiting: enabled Burst: 10 Limit: 37 Maxsize: 5000 Period (msec): 100 Max rate (msgs/sec): 100
The following example shows how to configure a router to send a maximum of 5 RSVP traffic engineering signaling messages in 1 second to a neighbor. The size of the output queue is 35.
configure terminal ip rsvp signalling rate-limit period 1 burst 5 maxsize 35
Example Managing Link Failure Timeouts for MPLS Traffic Engineering Tunnels
The following example shows how to manage link failure timeouts for MPLS traffic engineering tunnels:
configure terminal mpls traffic-eng topology holddown sigerr 15 end
In this example, the link hold-down time for signaling errors is set to 15 seconds.
Example Controlling IS-IS Communication with the MPLS Traffic Engineering Topology Database
The following example shows how to control IS-IS communication with the MPLS traffic engineering topology database:
configure terminal router isis mpls traffic-eng scanner interval 5 max-flash 50 end
In this example, the router is enabled to process up to 50 IS-IS LSPs without any delay.
Additional References
Related Documents
Related Topic |
Document Title |
---|---|
Cisco IOS commands |
|
Quality of service |
|
MPLS |
Standards
Standard |
Title |
---|---|
No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature. |
-- |
MIBs
MIB |
MIBs Link |
---|---|
No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature. |
To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL: |
RFCs
RFC |
Title |
---|---|
No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature. |
-- |
Technical Assistance
Description |
Link |
---|---|
The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password. |
Feature Information for MPLS Traffic Engineering Scalability Enhancements
The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Feature Name |
Releases |
Feature Information |
---|---|---|
MPLS Traffic Engineering: Scalability Enhancements |
Cisco IOS XE Release 2.3 |
The MPLS Traffic Engineering--Scalability Enhancements feature improves scalability performance for large numbers of traffic engineering tunnels. These improvements allow an increase in the number of traffic engineering (TE) tunnels a router can support when the router is configured as a tunnel headend. Additionally, when the router is configured as a tunnel midpoint, the enhancements reduce the time required to establish large numbers of TE tunnels. This feature module contains information about and instructions on how to configure the Multiprotocol Label Switching (MPLS) traffic engineering scalability enhancements. The following commands were introduced or modified: clear ip rsvp counters, clear ip rsvp signalling rate-limit, clear mpls traffic-eng tunnel counters, ip rsvp signalling rate-limit, mpls traffic-eng scanner, mpls traffic-eng topology holddown sigerr, show ip rsvp counters, and show mpls traffic-eng tunnels statistics. |
Glossary
bundled interface—Generic terms to represent port-channel, multilink, and VLAN interfaces.
Cisco express forwarding —A means for accelerating the forwarding of packets within a router, by storing route lookup information in several data structures instead of in a route cache.
CLNS —Connectionless Network Service. The Open Systems Interconnection (OSI) network layer service that does not require a circuit to be established before data is transmitted. CLNS routes messages to their destination independently of any other messages.
CSPF —Constrained Shortest Path First. A routing protocol that calculates the shortest path based on a set of constraints, such as a minimum bandwidth requirement, maximum number of nodes, or nodes to include or exclude.
enterprise network —A large and diverse network connecting most major points in a company or other organization.
FRR—Fast ReRoute.
headend —The endpoint of a broadband network. All stations send toward the headend; the headend then sends toward the destination stations.
IGP —Interior Gateway Protocol. An Internet protocol used to exchange routing information within an autonomous system. Examples of common Internet IGPs include Interior Gateway Routing protocol (IGRP), Open Shortest Path First (OSPF), and Routing Information Protocol (RIP).
interface —A network connection.
IS-IS —Intermediate System to Intermediate System. OSI link-state hierarchical routing protocol based on DECnet Phase V routing, where ISs (routers) exchange routing information based on a single metric, to determine the network topology.
LDN— Link Down Notification.
LSP —Label-Switched Path. A sequence of hops (R0...Rn) in which a packet travels from R0 to Rn through label switching mechanisms. A label-switched path can be chosen dynamically, based on normal routing mechanisms, or through configuration.
member links—Individual interfaces that are grouped into a bundled interface.
message-pacing —The former name of the rate limiting feature.
MPLS —Formerly known as tag switching, Multiprotocol Label Switching is a method for directing packets primarily through Layer 2 switching rather than Layer 3 routing. In MPLS, packets are assigned short fixed-length labels at the ingress to an MPLS cloud by using the concept of forwarding equivalence classes. Within the MPLS domain, the labels are used to make forwarding decisions mostly without recourse to the original packet headers.
OSPF —Open Shortest Path First. A link-state, hierarchical Interior Gateway Protocol (IGP) routing protocol. derived from the Intermediate System-Intermediate System (IS-IS) protocol. OSPF features are least-cost routing, multipath routing, and load balancing.
router —A network layer device that uses one or more metrics to determine the optimal path along which network traffic should be forwarded. Routers forward packets from one network to another based on network layer information.
RSVP —Resource Reservation Protocol. A protocol that supports the reservation of resources across an IP network.
scalability —An indicator showing how quickly some measure of resource usage increases as a network gets larger.
TLV —type, length, value. TLV objects are used in data communication to provide optional information. The type field indicates the type of items in the value field. The length field indicates the length of the value field. The value field is the data portion of the packet.
topology —The physical arrangement of network nodes and media within an enterprise networking structure.
TE (traffic engineering) —Techniques and processes that cause routed traffic to travel through the network on a path other than the one that would have been chosen if standard routing methods were used.
traffic engineering tunnel —A label-switched tunnel that is used for traffic engineering. Such a tunnel is set up through means other than normal Layer 3 routing; it is used to direct traffic over a path different from the one that Layer 3 routing would cause the tunnel to take.