|
Command or Action |
Purpose |
Step 1 |
enable
Example:
Router> enable |
Enables privileged EXEC mode.
-
Enter your password if prompted.
|
Step 2 |
configure terminal
Example:
Router# configure terminal |
Enters global configuration mode. |
Step 3 |
ip sla operation-number
Example:
Router(config)# ip sla 10 |
Begins configuration for an IP SLAs operation and enters IP SLA configuration mode. |
Step 4 |
udp-jitter {destination-ip-address | destination-hostname} destination-port [source-ip {ip-address | hostname}] [source-port port-number] [control {enable | disable}] [num-packets number-of-packets] [interval interpacket-interval]
Example:
Router(config-ip-sla)# udp-jitter 172.29.139.134 5000 |
Configures the IP SLAs operation as a UDP jitter operation and enters UDP jitter configuration submode.
-
Use the control disable keyword combination only if you disable the IP SLAs control protocol on both the source and target routers.
|
Step 5 |
history distributions-of-statistics-kept size
Example:
Router(config-ip-sla-jitter)# history distributions-of-statistics-kept 5 |
(Optional) Sets the number of statistics distributions kept per hop during an IP SLAs operation. |
Step 6 |
history enhanced [interval seconds] [buckets number-of-buckets]
Example:
Router(config-ip-sla-jitter)# history enhanced interval 900 buckets 100 |
(Optional) Enables enhanced history gathering for an IP SLAs operation. |
Step 7 |
frequency seconds
Example:
Router(config-ip-sla-jitter)# frequency 30 |
(Optional) Sets the rate at which a specified IP SLAs operation repeats. |
Step 8 |
history hours-of-statistics-kept hours
Example:
Router(config-ip-sla-jitter)# history hours-of-statistics-kept 4 |
(Optional) Sets the number of hours for which statistics are maintained for an IP SLAs operation. |
Step 9 |
owner owner-id
Example:
Router(config-ip-sla-jitter)# owner admin |
(Optional) Configures the Simple Network Management Protocol (SNMP) owner of an IP SLAs operation. |
Step 10 |
request-data-size bytes
Example:
Router(config-ip-sla-jitter)# request-data-size 64 |
(Optional) Sets the protocol data size in the payload of an IP SLAs operation's request packet. |
Step 11 |
history statistics-distribution-interval milliseconds
Example:
Router(config-ip-sla-jitter)# history statistics-distribution-interval 10 |
(Optional) Sets the time interval for each statistics distribution kept for an IP SLAs operation. |
Step 12 |
tag text
Example:
Router(config-ip-sla-jitter)# tag TelnetPollServer1 |
(Optional) Creates a user-specified identifier for an IP SLAs operation. |
Step 13 |
threshold milliseconds
Example:
Router(config-ip-sla-jitter)# threshold 10000 |
(Optional) Sets the upper threshold value for calculating network monitoring statistics created by an IP SLAs operation. |
Step 14 |
timeout milliseconds
Example:
Router(config-ip-sla-jitter)# timeout 10000 |
(Optional) Sets the amount of time an IP SLAs operation waits for a response from its request packet. |
Step 15 |
Do one of the following:
-
tos number
-
traffic-class number
Example:
Router(config-ip-sla-jitter)# tos 160
Example:
Router(config-ip-sla-jitter)# traffic-class 160 |
(Optional) In an IPv4 network only, defines the ToS byte in the IPv4 header of an IP SLAs operation. or (Optional) In an IPv6 network only, defines the traffic class byte in the IPv6 header for a supported IP SLAs operation. |
Step 16 |
flow-label number
Example:
Router(config-ip-sla-jitter)# flow-label 112233 |
(Optional) In an IPv6 network only, defines the flow label field in the IPv6 header for a supported IP SLAs operation. |
Step 17 |
verify-data
Example:
Router(config-ip-sla-jitter)# verify-data |
(Optional) Causes an IP SLAs operation to check each reply packet for data corruption. |
Step 18 |
vrf vrf-name
Example:
Router(config-ip-sla-jitter)# vrf vpn-A |
(Optional) Allows monitoring within Multiprotocol Label Switching (MPLS) Virtual Private Networks (VPNs) using IP SLAs operations. |
Step 19 |
exit
Example:
Router(config-ip-sla-jitter)# exit |
Exits UDP jitter configuration submode and returns to global configuration mode. |
Step 20 |
ip sla schedule operation-number [life {forever| seconds}] [start-time {hh:mm[:ss] [month day | day month] | pending | now | after hh:mm:ss}] [ageout seconds] [recurring]
Example:
Router(config)# ip sla schedule 5 start-time now life forever |
Configures the scheduling parameters for an individual IP SLAs operation. |
Step 21 |
exit
Example:
Router(config)# exit |
(Optional) Exits global configuration mode and returns to privileged EXEC mode. |
Step 22 |
show ip sla configuration [operation-number]
Example:
Router# show ip sla configuration 10 |
(Optional) Displays configuration values including all defaults for all IP SLAs operations or a specified operation. |