Copyright Page

Chapter 1. Cisco Discovery Protocol Version 2

Finding Feature Information

Prerequisites for Using Cisco Discovery Protocol

Restrictions for Using Cisco Discovery Protocol

Information About Using Cisco Discovery Protocol

VLAN Trunking Protocol

Type-Length-Value Fields

Cisco Discovery Protocol

Using Cisco Discovery Protocol with SNMP

Cisco Discovery Protocol and On-Demand Routing Support for ATM PVCs

Cisco Discovery Protocol Support in IPv6

Benefits of Cisco Discovery Protocol

How to Use Cisco Discovery Protocol Version 2

Disabling and Enabling Cisco Discovery Protocol on a Cisco Device

Disabling Cisco Discovery Protocol on a Supported Device

Enabling Cisco Discovery Protocol on a Supported Device

Disabling and Enabling Cisco Discovery Protocol on a Supported Interface

Disabling Cisco Discovery Protocol on a Supported Interface

Enabling Cisco Discovery Protocol on a Supported Interface

Setting the Transmission Timer and Hold Time

Disabling and Reenabling Cisco Discovery Protocol Version 2 Advertisements

Disabling Cisco Discovery Protocol Version 2 Advertisements

Enabling Cisco Discovery Protocol Version 2 Advertisements

Monitoring and Maintaining Cisco Discovery Protocol

Configuration Examples for Cisco Discovery Protocol Version 2

Example: Setting the Transmission Timer and Hold Time

Example: Monitoring and Maintaining Cisco Discovery Protocol

Additional References for Cisco Discovery Protocol Version 2

Feature Information for Cisco Discovery Protocol Version 2

Chapter 2. Secure Cisco Discovery Protocol

Finding Feature Information

Prerequisites for Secure Cisco Discovery Protocol

Restrictions for Secure Cisco Discovery Protocol

Information About Secure Cisco Discovery Protocol

Secure Cisco Discovery Protocol

Supported Type, Length, Value Fields

How to Configure Secure Cisco Discovery Protocol

Configuring a TLV List and Adding TLVs to the List

Applying TLV List Configurations at the Interface Level

Applying TLV List Configurations at the Global Level

Configuration Examples for Secure Cisco Discovery Protocol

Example: Configuring a TLV List and Adding TLVs to the List

Example: Applying TLV List Configurations at Interface Level

Example: Applying TLV List Configurations Globally

Additional References for Secure Cisco Discovery Protocol

Feature Information for Secure Cisco Discovery Protocol

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: Click Here . Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Chapter 1. Cisco Discovery Protocol Version 2

Cisco Discovery Protocol (formerly known as CDP) is a Layer 2, media-independent, and network-independent protocol that runs on Cisco devices and enables networking applications to learn about directly connected devices nearby. This protocol facilitates the management of Cisco devices by discovering these devices, determining how they are configured, and allowing systems using different network-layer protocols to learn about each other.

This module describes Cisco Discovery Protocol Version 2 and how it functions with Simple Network Management Protocol (SNMP).

- Finding Feature Information

- Prerequisites for Using Cisco Discovery Protocol

- Restrictions for Using Cisco Discovery Protocol

- Information About Using Cisco Discovery Protocol

- How to Use Cisco Discovery Protocol Version 2

- Configuration Examples for Cisco Discovery Protocol Version 2

- Additional References for Cisco Discovery Protocol Version 2

- Feature Information for Cisco Discovery Protocol Version 2

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to Click Here . An account on Cisco.com is not required.

Prerequisites for Using Cisco Discovery Protocol

- Interfaces must support Subnetwork Access Protocol (SNAP) headers.

Restrictions for Using Cisco Discovery Protocol

- Cisco Discovery Protocol functions only on Cisco devices.

- Cisco Discovery Protocol is not supported on Frame Relay multipoint subinterfaces.

Information About Using Cisco Discovery Protocol

- VLAN Trunking Protocol

- Type-Length-Value Fields

- Cisco Discovery Protocol

- Benefits of Cisco Discovery Protocol

VLAN Trunking Protocol

VLAN Trunking Protocol (VTP) is a discovery technique used by switches. A switch advertises its management domain, configuration revision number, VLANs, and their specific parameters on its trunk ports. A VTP domain is made up of a single device or interconnected devices that share the same VTP domain name. A switch can belong to only one VTP domain.

Type-Length-Value Fields

Type-Length-Value (TLV) fields are blocks of information embedded in Cisco Discovery Protocol advertisements. Information in advertisements varies, and the TLV frame format allows for extending advertisements when needed. The table below summarizes the TLV definitions.

Type-Length-Value Definitions for Cisco Discovery Protocol Version 2

TLV

Definition

Address TLV

Contains network addresses of both receiving and sending devices.

Application TLV

Provides a mechanism to send an application-specific TLV through Cisco Discovery Protocol.

Capabilities TLV

Identifies the device type, which indicates the functional capability of the device. For example, a switch.

Device-ID TLV

Identifies the device name in the form of a character string.

Full or Half Duplex TLV

Indicates the duplex configuration of the Cisco Discovery Protocol broadcast interface. This information is used by network operators to diagnose connectivity problems between adjacent network devices.

IP Network Prefix TLV

Contains a list of network prefixes to which a sending device can forward IP packets. A prefix includes the interface protocol and the port number. For example, Ethernet 1/0.

Location TLV

Delivers location-based information to endpoint devices through access devices (switches or routers) by using Cisco Discovery Protocol. The location TLV can send the following types of information:

- Civic location information—Provides the civic address information and the postal information. Examples include street address, road name, and postal community name.

- ELIN location information—Provides the location information of a caller. The location is determined by the emergency location identifier number (ELIN), which is a phone number that routes an emergency call to the local public safety answering point (PSAP) and which the PSAP can use to call back the emergency caller.

You must configure the location TLV on the device before Cisco Discovery Protocol can deliver location-based information to endpoint devices. For more information about configuring location TLV, see the Using Link Layer Discovery Protocol in Multivendor Networks module.

Location-Server TLV

Provides a mechanism for location servers to transfer the required information to neighboring devices.

Native VLAN TLV

Indicates, per interface, the assumed VLAN for untagged packets on the interface. Cisco Discovery Protocol learns the native VLAN for an interface.

This field is implemented only for interfaces that support the IEEE 802.1Q protocol.

Platform TLV

Identifies the hardware platform of the device. For example, Cisco 4500.

Port-ID TLV

Identifies the port on which a Cisco Discovery Protocol packet is sent.

Version TLV

Contains the device software release information.

VTP Management Domain TLV

Advertises the configured VLAN Trunking Protocol (VTP)-management-domain name of the system. This name is used by network operators to verify VTP-domain configuration in adjacent network nodes.

Cisco Discovery Protocol

Cisco Discovery Protocol is a Layer 2, media-independent, and network-independent protocol that networking applications use to learn about nearby, directly connected devices. Cisco Discovery Protocol is enabled by default. Each device configured for Cisco Discovery Protocol advertises at least one address at which the device can receive messages and sends periodic advertisements (messages) to the well-known multicast address 01:00:0C:CC:CC:CC. Devices discover each other by listening at that address. They also listen to messages to learn when interfaces on other devices are up or go down.

Advertisements contain time-to-live information, which indicates the length of time a receiving device should hold Cisco Discovery Protocol information before discarding it. Advertisements supported and configured in Cisco software are sent, by default, every 60 seconds on interfaces that support Subnetwork Access Protocol (SNAP) headers. Cisco devices never forward Cisco Discovery Protocol packets. Cisco devices that support Cisco Discovery Protocol store the information received in a table. Information in this table is refreshed every time an advertisement is received, and information about a device is discarded after three advertisements from that device are missed.

The information contained in Cisco Discovery Protocol advertisements varies based on the type of device and the installed version of the operating system. Some of the information that Cisco Discovery Protocol can learn includes:

- Cisco IOS version running on Cisco devices

- Hardware platform of devices

- IP addresses of interfaces on devices

- Locally connected devices advertising Cisco Discovery Protocol

- Interfaces active on Cisco devices, including encapsulation type

- Hostname

- Duplex setting

- VLAN Trunking Protocol (VTP) domain

- Native VLAN

Cisco Discovery Protocol Version 2 provides more intelligent, device-tracking features than those available in Version 1. One of the features available is an enhanced reporting mechanism for more rapid error tracking, which helps to reduce network downtime. Errors reported include mismatched native VLAN IDs (IEEE 802.1Q) on connected ports and mismatched port-duplex states between connected devices. Messages about reported errors can be sent to the console or to a logging server.

You can use show commands for getting detailed output on VTP management domains and duplex modes of neighboring devices, counters related to Cisco Discovery Protocol, and VLAN IDs of connecting ports.

- Using Cisco Discovery Protocol with SNMP

- Cisco Discovery Protocol and On-Demand Routing Support for ATM PVCs

- Cisco Discovery Protocol Support in IPv6

Using Cisco Discovery Protocol with SNMP

Using Cisco Discovery Protocol with Simple Network Management Protocol (SNMP) allows network management applications to learn the type of device and the SNMP agent address of neighboring devices. Applications can also send SNMP queries to these neighboring devices.

The SNMP management application learns protocol addresses and types of neighboring devices by retrieving the Cisco Discovery Protocol tables from SNMP agents on those devices. When enabled, the network management module (NMM) SNMP agent discovers neighboring devices and builds its local cache with information about these devices. A management workstation can retrieve this cache by sending SNMP requests to access CISCO-CDP-MIB.

Cisco Discovery Protocol and On-Demand Routing Support for ATM PVCs

Cisco Discovery Protocol and On-Demand Routing (ODR) support exists for ATM point-to-point permanent virtual circuits (PVCs). ODR uses Cisco Discovery Protocol to propagate IP address information in hub-and-spoke topologies. When ODR is enabled, spoke routers automatically advertise their subnets by using Cisco Discovery Protocol.

Cisco Discovery Protocol is disabled by default on ATM PVC interfaces. To enable Cisco Discovery Protocol, use the cdp run command in global configuration mode and the cdp enable command in interface configuration mode on both ends of the PVC. To enable ODR, use the router odr command in global configuration mode on the hub router, and turn off all dynamic-routing protocols on the spoke routers. For details about configuring ODR, see the “Configuring On-Demand Routing” section in the IP Routing: ODR Configuration Guide.

Cisco Discovery Protocol Support in IPv6

Cisco Discovery Protocol in IPv6 functions in the same way as in IPv4 and offers the same benefits. The IPv6 enhancement allows Cisco Discovery Protocol to exchange IPv6 and neighbor addressing information. The enhancement also provides IPv6 information to network management products and troubleshooting tools.

Benefits of Cisco Discovery Protocol

Cisco Discovery Protocol provides the following benefits:

- Allows systems using different network layer protocols to learn about one another.

- Facilitates management of Cisco devices by discovering them and discovering how they are configured.

- Assists with troubleshooting Type-Length-Value Fields (TLV) fields.

- Works with SNMP by learning SNMP agent addresses and sending SNMP queries.

How to Use Cisco Discovery Protocol Version 2

- Disabling and Enabling Cisco Discovery Protocol on a Cisco Device

- Disabling and Enabling Cisco Discovery Protocol on a Supported Interface

- Setting the Transmission Timer and Hold Time

- Disabling and Reenabling Cisco Discovery Protocol Version 2 Advertisements

- Monitoring and Maintaining Cisco Discovery Protocol

Disabling and Enabling Cisco Discovery Protocol on a Cisco Device

- Disabling Cisco Discovery Protocol on a Supported Device

- Enabling Cisco Discovery Protocol on a Supported Device

Disabling Cisco Discovery Protocol on a Supported Device

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    no cdp run

4.    end

DETAILED STEPS

Command or Action

Purpose

Step 1

enable

Example:

Device> enable

Enables privileged EXEC mode.

- Enter your password if prompted.

Step 2

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 3

no cdp run

Example:

Device(config)# no cdp run

Disables Cisco Discovery Protocol on a supported device.

Step 4

end

Example:

Device(config)# end

Returns the CLI to privileged EXEC mode.

Enabling Cisco Discovery Protocol on a Supported Device

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    cdp run

4.    end

DETAILED STEPS

Command or Action

Purpose

Step 1

enable

Example:

Device> enable

Enables privileged EXEC mode.

- Enter your password if prompted.

Step 2

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 3

cdp run

Example:

Device(config)# cdp run

Enables Cisco Discovery Protocol on a supported device.

Step 4

end

Example:

Device(config)# end

Exits configuration mode and returns to privileged EXEC mode.

Disabling and Enabling Cisco Discovery Protocol on a Supported Interface

- Disabling Cisco Discovery Protocol on a Supported Interface

- Enabling Cisco Discovery Protocol on a Supported Interface

Disabling Cisco Discovery Protocol on a Supported Interface

If the encapsulation of an interface is changed, Cisco Discovery Protocol is reenabled on that interface even if Cisco Discovery Protocol was previously disabled. For example, when interface encapsulation changes from PPP to High-Level Data Link Control (HDLC), Cisco Discovery Protocol is reenabled on that interface even though it was explicitly disabled with the no cdp run command on that interface. This behavior is by design. The encapsulation changes the Layer 2 protocol configured for that interface and resets the interface configuration to the default Cisco Discovery Protocol state of being enabled, assuming that Cisco Discovery Protocol is enabled globally on the device.

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    interface type number [name-tag]

4.    no cdp enable

5.    end

DETAILED STEPS

Command or Action

Purpose

Step 1

enable

Example:

Device> enable

Enables privileged EXEC mode.

- Enter your password if prompted.

Step 2

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 3

interface type number [name-tag]

Example:

Device(config)# interface ethernet 0/1

Configures the specified interface and enters interface configuration mode.

Step 4

no cdp enable

Example:

Device(config-if)# no cdp enable

Disables Cisco Discovery Protocol on the interface.

Note:
If the encapsulation of an interface is changed, Cisco Discovery Protocol is reenabled on that interface even if Cisco Discovery Protocol was previously disabled.

Step 5

end

Example:

Device(config-if)# end

Exits to privileged EXEC mode.

Example

In the following example, Cisco Discovery Protocol is first disabled on an interface:

Device(config)# interface fastethernet 3/0
Device(config-if)# no ip address

Device(config-if)# shutdown
Device(config-if)# no cdp enable
! Cisco Discovery Protocol is disabled.
Device(config-if)# end

In the following example, the encapsulation of the interface is changed from PPP to HDLC:

Device# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Device(config)# interface fastethernet 3/0

! Encapsulation changed from PPP to HDLC.
Device(config-if)# do show running interface fastethernet 3/0
Current configuration : 49 bytes
!

The following example shows that Cisco Discovery Protocol is reenabled after the encapsulation for the interface is changed even though Cisco Discovery Protocol was previously disabled:

Device(config)# interface fastethernet 3/0
Device(config-if)# no ip address
Device(config-if)# shutdown
! Cisco Discovery Protocol is now back on. You don't see it here previously disabled.
Device(config-if)# end

Enabling Cisco Discovery Protocol on a Supported Interface

Note

If the encapsulation of an interface is changed, Cisco Discovery Protocol is reenabled on that interface, even if Cisco Discovery Protocol was previously disabled.

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    interface type number [name-tag]

4.    cdp enable

5.    end

DETAILED STEPS

Command or Action

Purpose

Step 1

enable

Example:

Device> enable

Enables privileged EXEC mode.

- Enter your password if prompted.

Step 2

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 3

interface type number [name-tag]

Example:

Device(config)# interface ethernet 0/1

Configures the specified interface and places the CLI in interface configuration mode.

Note:
If the encapsulation of an interface is changed, Cisco Discovery Protocol is reenabled on that interface, even if Cisco Discovery Protocol was previously disabled.

Step 4

cdp enable

Example:

Device(config-if)# cdp enable

Enables Cisco Discovery Protocol on the interface.

Step 5

end

Example:

Device(config-if)# end

Returns the CLI to privileged EXEC mode.

Setting the Transmission Timer and Hold Time

Perform this task to set the frequency of Cisco Discovery Protocol transmissions and the hold time for Cisco Discovery Protocol packets.

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    cdp timer seconds

4.    cdp holdtime seconds

5.    end

DETAILED STEPS

Command or Action

Purpose

Step 1

enable

Example:

Device> enable

Enables privileged EXEC mode.

- Enter your password if prompted.

Step 2

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 3

cdp timer seconds

Example:

Device(config)# cdp timer 30

Specifies the frequency of transmission of Cisco Discovery Protocol packets.

Step 4

cdp holdtime seconds

Example:

Device(config)# cdp holdtime 90

Specifies the time for which a receiving device should hold information before discarding it.

Step 5

end

Example:

Device(config)# end

Enters privileged EXEC mode.

Disabling and Reenabling Cisco Discovery Protocol Version 2 Advertisements

The broadcasting of Cisco Discovery Protocol Version 2 advertisements is enabled by default on Cisco devices. To disable or reenable this broadcasting, perform these tasks.

- Disabling Cisco Discovery Protocol Version 2 Advertisements

- Enabling Cisco Discovery Protocol Version 2 Advertisements

Disabling Cisco Discovery Protocol Version 2 Advertisements

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    no cdp advertise-v2

4.    end

DETAILED STEPS

Command or Action

Purpose

Step 1

enable

Example:

Device> enable

Enables privileged EXEC mode.

- Enter your password if prompted.

Step 2

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 3

no cdp advertise-v2

Example:

Device(config)# no cdp advertise-v2

Disables the broadcasting of Cisco Discovery Protocol Version 2 advertisements.

Step 4

end

Example:

Device(config)# end

Exits to privileged EXEC mode.

Enabling Cisco Discovery Protocol Version 2 Advertisements

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    cdp advertise-v2

4.    end

DETAILED STEPS

Command or Action

Purpose

Step 1

enable

Example:

Device> enable

Enables privileged EXEC mode.

- Enter your password if prompted.

Step 2

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 3

cdp advertise-v2

Example:

Device(config)# cdp advertise-v2

Enables the broadcasting of Cisco Discovery Protocol Version 2 advertisements.

Step 4

end

Example:

Device(config)# end

Exits to privileged EXEC mode.

Monitoring and Maintaining Cisco Discovery Protocol

Perform this task to monitor and maintain Cisco Discovery Protocol on a device. This task and all its steps are optional, and the steps can be performed in any sequence.

SUMMARY STEPS

1.    enable

2.    clear cdp counters

3.    clear cdp table

4.    show cdp

5.    show cdp entry device-name [protocol | version]

6.    show cdp interface [type number]

7.    show cdp neighbors [type number] [detail]

8.    show cdp traffic

9.    show debugging

DETAILED STEPS

Command or Action

Purpose

Step 1

enable

Example:

Device> enable

Enables privileged EXEC mode.

- Enter your password if prompted.

Step 2

clear cdp counters

Example:

Device# clear cdp counters

Resets Cisco Discovery Protocol traffic counters to zero.

Step 3

clear cdp table

Example:

Device# clear cdp table

Clears the table that contains Cisco Discovery Protocol information about neighbors.

Step 4

show cdp

Example:

Device# show cdp

Displays the interval between advertisements, the number (in seconds) for which an advertisement is valid for a given port, and the version of the advertisement.

Step 5

show cdp entry device-name [protocol | version]

Example:

Device# show cdp entry test-device protocol

Displays information about a specific neighbor.

Step 6

show cdp interface [type number]

Example:

Device# show cdp interface

Displays information about interfaces on which Cisco Discovery Protocol is enabled.

Step 7

show cdp neighbors [type number] [detail]

Example:

Device# show cdp neighbors

Displays the type of device that has been discovered, the name of the device, the number and type of the local interface (port), the time (in seconds) the Cisco Discovery Protocol advertisement is valid for the interface, the device type, the device product number, and the port ID.

- The detail keyword displays information about the native VLAN ID, the duplex mode, and the VTP domain name associated with neighboring devices.

Step 8

show cdp traffic

Example:

Device# show cdp traffic

Displays information about Cisco Discovery Protocol traffic, including the number of packets sent and received and checksum errors.

Step 9

show debugging

Example:

Device# show debugging

Displays information about the types of debugging that are enabled for the device.

Configuration Examples for Cisco Discovery Protocol Version 2

- Example: Setting the Transmission Timer and Hold Time

- Example: Monitoring and Maintaining Cisco Discovery Protocol

Example: Setting the Transmission Timer and Hold Time

In the following example, the timer is set to send updates every 30 seconds and a show cdp interface command is used to verify that the update is effective:

Device(config)# cdp timer 30
Device(config)# end
Device# show cdp interface

Serial0 is up, line protocol is up
Encapsulation is HDLC
Sending CDP packets every 30 seconds
Holdtime is 180 seconds

In the following example, the hold time is set to 90 seconds and a show cdp interface command is used to verify that the update is effective:

Device(config)# cdp holdtime 90
Device(config)# end
Device# show cdp interface

Serial0 is up, line protocol is up
Encapsulation is HDLC
Sending CDP packets every 30 seconds
Holdtime is 90 seconds

Example: Monitoring and Maintaining Cisco Discovery Protocol

The following example shows a series of commands that you can use to view Cisco Discovery Protocol information:

Device# show cdp

Global CDP information:
Sending CDP packets every 60 seconds
Sending a holdtime value of 180 seconds
Sending CDPv2 advertisements is enabled

Device# show cdp neighbors

Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater

Device ID        Local Interfce     Holdtme    Capability  Platform  Port ID
C2950-1          Fas 0/0            148         S I       WS-C2950T-Fas 0/15
RX-SWV.cisco.com Fas 0/1            167         T S       WS-C3524-XFas 0/13
Device# show cdp neighbors detail

-------------------------
Device ID: C2950-1
Entry address(es):
Platform: Cisco WS-C2950T-24,  Capabilities: Switch IGMP
Interface: FastEthernet0/0,  Port ID (outgoing port): FastEthernet0/15
Holdtime : 139 sec
Version :
Cisco IOS C2950 Software (C2950-I6Q4L2-M), Version 12.1(9)EA1, RELEASE SOFTWARE
.
.
.
Device# show cdp traffic

CDP counters :
Total packets output: 81684, Input: 81790
Hdr syntax: 0, Chksum error: 0, Encaps failed: 0
No memory: 0, Invalid packet: 0, Fragmented: 0
CDP version 1 advertisements output: 0, Input: 0
CDP version 2 advertisements output: 81684, Input: 81790

Additional References for Cisco Discovery Protocol Version 2

Related Documents

Related Topic

Document Title

Cisco IOS commands

Cisco IOS Master Command List, All Releases

Cisco Discovery Protocol commands

Cisco IOS Cisco Discovery Protocol Command Reference

SNMP support configuration tasks

“Configuring SNMP Support” module

On-Demand Routing configuration tasks

“Configuring On-Demand Routing” module

Debug commands

Cisco IOS Debug Command Reference

Standards

Standard

Title

IEEE 802.1Q

Virtual LANs

MIBs

MIB

MIBs Link

CISCO-CDP-MIB

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

Click Here

Technical Assistance

Description

Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

Click Here

Feature Information for Cisco Discovery Protocol Version 2

The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to Click Here . An account on Cisco.com is not required.

Feature Information for Cisco Discovery Protocol Version 2

Feature Name

Releases

Feature Information

Cisco Discovery Protocol Version 2

Cisco Discovery Protocol is a Layer 2, media-independent, and network-independent protocol that runs on Cisco devices and enables networking applications to learn about nearby, directly connected devices. This protocol facilitates the management of Cisco devices and allows systems using different network layer protocols to learn about one another.

Chapter 2. Secure Cisco Discovery Protocol

The Cisco Discovery Protocol does not possess inherent security mechanisms and is vulnerable to attacks. The Secure Cisco Discovery Protocol feature allows users to select the type, length, value (TLV) fields that are sent on a particular interface to filter information sent through Cisco Discovery Protocol packets.

- Finding Feature Information

- Prerequisites for Secure Cisco Discovery Protocol

- Restrictions for Secure Cisco Discovery Protocol

- Information About Secure Cisco Discovery Protocol

- How to Configure Secure Cisco Discovery Protocol

- Configuration Examples for Secure Cisco Discovery Protocol

- Additional References for Secure Cisco Discovery Protocol

- Feature Information for Secure Cisco Discovery Protocol

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to Click Here . An account on Cisco.com is not required.

Prerequisites for Secure Cisco Discovery Protocol

The Cisco software image must support basic Cisco Discovery Protocol functions.

Restrictions for Secure Cisco Discovery Protocol

Blocking the type, length, value (TLV) fields on one device can affect the functionality of clients on other devices where Cisco Discovery Protocol packets with blocked TLV fields are received because different clients use different TLV fields.

Information About Secure Cisco Discovery Protocol

- Secure Cisco Discovery Protocol

- Supported Type, Length, Value Fields

Secure Cisco Discovery Protocol

The Cisco Discovery Protocol does not possess inherent security mechanisms and is vulnerable to attacks. The Secure Cisco Discovery Protocol feature provides security by allowing users to select the type, length, value (TLV) fields that are sent on an interface to filter the fields in Cisco Discovery Protocol packets.

This feature supports the following functions:

- TLV lists can be configured globally and also at the interface level, but only one TLV fields list can be configured globally.

- A TLV list configured on an interface is given a higher precedence.

- All TLVs except the Device-ID TLV and the Application TLV can be blocked.

- Information about the Cisco Discovery Protocol TLV list configured on an interface is stored in each Cisco Discovery Protocol interface subblock.

- All TLVs are blocked on the sending side.

- The cdp tlv-list and cdp filter-tlv-list commands are required to configure a Cisco Discovery Protocol list and apply the list globally or on an interface.

- The show cdp tlv-list and show cdp interface commands display information about the TLV list.

Supported Type, Length, Value Fields

Supported TLV fields

Related command in TLV list configuration mode

TLV Fields

Description

address

Address TLV

Contains a list of device network-layer addresses. If a device uses Simple Network Management Protocol (SNMP), the first address is an address at which the device receives SNMP messages.

The device may advertise all of its addresses and may optionally advertise one or more loopback IP addresses.

capability

Capability TLV

Identifies the device type. The device type indicates the functional capability of the device, for example, a switch.

cos

Class of service TLV

Describes the Layer 2 class of service (CoS) value in a Cisco Discovery Protocol packet. All Cisco Discovery Protocol packets received on an untrusted port are marked with a CoS value by a switching device that cannot classify individual packets.

This TLV is used only in a Cisco Discovery Protocol packet that contains an Extended Trust TLV, which indicates the absence of extended trust with a CoS TLV that is one byte in length.

default

Default

Specifies the default state of the configuration.

duplex

Duplex TLV

Allows devices to recognize if a point-to-point Ethernet interface is running in full-duplex or in half-duplex mode. Network problems are caused if two ends of a link are in different modes.

The TLV value is one byte in length with its least significant bit indicating the mode. A 1 indicates full-duplex and a 0’indicates half-duplex.

exit

Exit

Exits current configuration.

ext-port-id

External Port Id TLV

Identifies the physical connector port on which a Cisco Discovery Protocol packet is transmitted.

This TLV is used in devices with optical ports in which signals from multiple hardware interfaces are multiplexed through a single physical port.

The value of this TLV must be the same as the MIB object ifName for the ifTable entry for the external port.

hello-protocol

Protocol-Hello TLV

Specifies that a particular protocol has asked Cisco Discovery Protocol to piggyback its “hello” messages within transmitted Cisco Discovery Protocol packets.

The value of this TLV protocol is greater than or equal to 5 and lesser than or equal to 32 bytes. The first 5 bytes are the protocol’s 5-byte Subnetwork Access Protocol (SNAP) value, which contains three bytes of organizationally unique identifier (OUI) followed by two bytes of protocol ID.

A Cisco Discovery Protocol packet may contain multiple protocol-hello TLVs, each for a different protocol.

ip-prefix

IP Network Prefix TLV

Describes a list of stub network prefixes to which the sending stub device can forward IP packets. These packets are used by On-Demand Routing (ODR).

Each network prefix is formatted as a 4-byte IP address followed by a 1-byte network mask length. Thus, the length of the value sent by a stub device is a multiple of 5 bytes.

location

Location TLV

Delivers location-based information to endpoint devices through switches, routers, or access devices using the Cisco Discovery Protocol. The Location TLV can send the following types of information:

- Custom location—Provides the location and attributes of the endpoint device.

- Civic location information—Provides the civic address information and postal information; for example, street address, road name, and postal community information.

- ELIN location information—Provides the location information of a caller. The location is determined by the emergency location identifier number (ELIN), which is a phone number that routes an emergency call to the local public safety answering point (PSAP). The PSAP uses this information to call back.

- Geo spatial location information—Provides the longitude, latitude, and altitude information of the endpoint device.

You must configure the location TLV on the device before Cisco Discovery Protocol can deliver location-based information to the endpoint devices.

location-server

Location-server TLV

Provides a mechanism for location servers to transfer the required information to the neighbor devices.

mgmt-address

Management Address TLV

Contains a list of network layer addresses encoded similarly to the Address TLV.

This TLV contains a list of all the addresses at which the device accepts SNMP messages.

native-vlan

Native VLAN TLV

Indicates the Inter-Switch Link (ISL) number of the native interface VLAN on which the Cisco Discovery Protocol packet is sent, as well as whether the VLAN is enabled on the link and whether the link is a trunk or a host/edge port.

platform

Platform TLV

Describes the hardware platform of the device. Encoded as an ASCII character string. The TLV length determines the length of the string.

port-id

Port-ID TLV

Identifies the port on which the Cisco Discovery Protocol packet is sent. This is encoded as an ASCII character string.

The value of this TLV is the same as the MIB object ifName for the ifTable entry on which the Cisco Discovery Protocol packet is sent.

power -available

Power Available TLV

Specifies the information transmitted by all switch interfaces. This information permits a device that needs power to negotiate and select an appropriate power setting. The Power Available TLV includes four fields:

- Request-ID field

- Available-Power field

- Power-Management-ID field

- Management-Power-Level field

powernet

Energywise TLV

Discovers neighbor devices, communicates and negotiates power-related parameters with Cisco end devices such as an IP phone and access point.

trust

Extended Trust TLV

Specifies that the trust from the larger switch port is extended to other (external) ports of the simple switching device without explicitly configuring the trust on the simple switching device.

Extending trust allows a network administrator to trust a host/server to mark the packets and the port on which this host/server is connected. Packets received on a trusted port are not marked again.

The TLV value is one byte in length with its least significant bit indicating the trust mode. A 1 indicates extended trust and a 0 indicates the absence of extended trust. All other bits of the TLV value should be set to 0 on transmission and ignored on receipt.

A Cisco Discovery Protocol packet without this TLV indicates the absence of extended trust.

version

Version TLV

Contains information about the Cisco software image version the device is running. This is in the form of a character string. The TLV length determines the length of the string. This information is displayed in the output of the show version command.

vtp-mgmt-domain

VTP Management Domain TLV

Specifies the name of the VLAN Trunking Protocol (VTP) management domain for a device running the VTP on the particular interface on which the Cisco Discovery Protocol packet is sent.

The length of this TLV determines the length of the VTP management domain name. A length of zero indicates that a device is running VTP but has no management domain name assigned to it.

vvid

Appliance VLAN-ID TLV

Indicates the setting of the local configuration when a local 802.1Q interface has been configured to send and receive VoIP and related packets on a particular VLAN.

Devices receiving this TLV may adjust their configuration to match this setting.

Note

The Address TLV and Device ID TLV are mandatory TLVs and they cannot be blocked. Hence, they are not available in the Cisco software image for user configuration.

How to Configure Secure Cisco Discovery Protocol

- Configuring a TLV List and Adding TLVs to the List

- Applying TLV List Configurations at the Interface Level

- Applying TLV List Configurations at the Global Level

Configuring a TLV List and Adding TLVs to the List

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    cdp tlv-list tlv-list-name

4.    ip-prefix

5.    hello-protocol

6.    end

7.    show cdp tlv-list tlv-list-name

DETAILED STEPS

Command or Action

Purpose

Step 1

enable

Example:

Device> enable

Enables privileged EXEC mode.

- Enter your password if prompted.

Step 2

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 3

cdp tlv-list tlv-list-name

Example:

Device(config)# cdp tlv-list group1

Configures the type, length, value (TLV) list that allows users to select TLVs and enters TLV list configuration mode.

Step 4

ip-prefix

Example:

Device(config-tlv-list)# ip-prefix

Adds the IP prefix TLV to the TLV list.

Step 5

hello-protocol

Example:

Device(config-tlv-list)# hello-protocol

Adds the Protocol-Hello TLV to the TLV list.

Note:
In TLV list configuration mode, enter the CLI help (?) command to view a list of TLVs that are not added to the TLV list.

Step 6

end

Example:

Device(config-tlv-list)# end

Exits TLV list configuration mode and returns to privileged EXEC mode.

Step 7

show cdp tlv-list tlv-list-name

Example:

Device# show cdp tlv-list group1

Displays information about the TLVs in a TLV list.

Applying TLV List Configurations at the Interface Level

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    interface type number

4.    cdp filter-tlv-list tlv-list-name

5.    end

6.    show cdp tlv-list tlv-list-name

DETAILED STEPS

Command or Action

Purpose

Step 1

enable

Example:

Device> enable

Enables privileged EXEC mode.

- Enter your password if prompted.

Step 2

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 3

interface type number

Example:

Device# interface ethernet 0/0

Specifies an interface type and enters interface configuration mode.

Step 4

cdp filter-tlv-list tlv-list-name

Example:

Device(config-if)# cdp filter-tlv-list group1

Applies a TLV list on an interface.

Step 5

end

Example:

Device(config-if)# end

Exits interface configuration mode and returns to privileged EXEC mode.

Step 6

show cdp tlv-list tlv-list-name

Example:

Device# show cdp tlv-list group1

Displays information about the TLVs in a TLV list.

Applying TLV List Configurations at the Global Level

SUMMARY STEPS

1.    enable

2.    configure terminal

3.    cdp filter-tlv-list tlv-list-name

4.    end

5.    show cdp tlv-list tlv-list-name

DETAILED STEPS

Command or Action

Purpose

Step 1

enable

Example:

Device> enable

Enables privileged EXEC mode.

- Enter your password if prompted.

Step 2

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 3

cdp filter-tlv-list tlv-list-name

Example:

Device(config)# cdp filter-tlv-list group1

Applies a TLV list globally.

Step 4

end

Example:

Device(config)# end

Exits global configuration mode and returns to the privileged EXEC mode.

Step 5

show cdp tlv-list tlv-list-name

Example:

Device# show cdp tlv-list group1

Displays information about the TLVs in a TLV list.

Configuration Examples for Secure Cisco Discovery Protocol

- Example: Configuring a TLV List and Adding TLVs to the List

- Example: Applying TLV List Configurations at Interface Level

- Example: Applying TLV List Configurations Globally

Example: Configuring a TLV List and Adding TLVs to the List

The following example shows how to create a type, length, value (TLV) list, group1 and add TLVs to the list:

Device> enable
Device# configure terminal
Device(config)# cdp tlv-list group1
Device(config-tlv-list)# ip-prefix
Device(config-tlv-list)# hello-protocol
Device(config-tlv-list)# trust
Device(config-tlv-list)# capability

The following example shows how to create a TLV list, group2 and add TLVs to the list:

Device(config)# cdp tlv-list group2
Device(config-tlv-list)# address
Device(config-tlv-list)# duplex
Device(config-tlv-list)# capability
Device(config-tlv-list)# end

The following example shows how to view the TLV lists and the TLVs that are added to the lists:

Device# show cdp tlv-list group1

Tlv-list : group1
Capability  Hello-protocol  Ip-prefix  Trust

Device# show cdp tlv-list group2

Tlv-list : group2
Address  Capability  Duplex

Device# show cdp tlv-list *

Tlv-list : group1
Capability  Hello-protocol  Ip-prefix  Trust

Tlv-list : group2
Address  Capability  Duplex

Note

- The show cdp tlv-list * command displays all configured Cisco Discovery Protocol TLV lists.

Example: Applying TLV List Configurations at Interface Level

The show cdp interface command displays Cisco Discovery Protocol TLV lists on all interfaces.

The following example shows how to apply Cisco Discovery Protocol type, length, value (TLV) lists on an interface:

Device> enable
Device# configure terminal
Device(config)# interface ethernet 0/0
Device(config-if)# cdp filter-tlv-list group1
03:22:15: %CDP-6-TLV_LIST_INTERFACE: Tlv-list group1 applied on
interface Ethernet0/0
Device(config-if)# exit
Device(config)# interface ethernet 0/1
Device(config-if)# cdp filter-tlv-list group2
03:22:45: %CDP-6-TLV_LIST_INTERFACE: Tlv-list group2 applied on
interface Ethernet0/1
Device(config-if)# end
Device# show cdp tlv-list group1

Tlv-list : group1
Capability  Hello-protocol  Ip-prefix  Trust
Applied on:
Et0/0

Device# show cdp interface ethernet0/0

Ethernet0/0 is up, line protocol is up
Encapsulation ARPA
Sending CDP packets every 60 seconds
Holdtime is 180 seconds
Tlv-list applied : group1

Device# show cdp interface ethernet0/1

Ethernet0/1 is up, line protocol is up
Encapsulation ARPA
Sending CDP packets every 60 seconds
Holdtime is 180 seconds
Tlv-list applied : group2

Device# show cdp interface

Ethernet0/0 is up, line protocol is up
Encapsulation ARPA
Sending CDP packets every 60 seconds
Holdtime is 180 seconds
Tlv-list applied : group1
Ethernet0/1 is up, line protocol is up
Encapsulation ARPA
Sending CDP packets every 60 seconds
Holdtime is 180 seconds
Tlv-list applied : group2
.
.
.

Example: Applying TLV List Configurations Globally

The following example shows how to globally apply a Cisco Discovery Protocol type, length, value (TLV) list:

Device> enable
Device# configure terminal
Device(config)# cdp filter-tlv-list group1
03:28:44: %CDP-6-TLV_LIST_GLOBALLY: Tlv-list group1 applied globally on all
interfaces.
Device(config)# end
Device# show cdp interface

Ethernet0/0 is up, line protocol is up
Encapsulation ARPA
Sending CDP packets every 60 seconds
Holdtime is 180 seconds
Tlv-list applied : group1
Ethernet0/1 is up, line protocol is up
Encapsulation ARPA
Sending CDP packets every 60 seconds
Holdtime is 180 seconds
Tlv-list applied : group2
.
.
.

Note

The show cdp interface command displays Cisco Discovery Protocol TLV lists on all interfaces.

Additional References for Secure Cisco Discovery Protocol

Related Documents

Related Topic

Document Title

Cisco IOS commands

Cisco IOS Master Command List, All Releases

Cisco Discovery Protocol commands

Cisco IOS Cisco Discovery Protocol Command Reference

SNMP configuration tasks

Configuring SNMP Support

On-Demand Routing configuration tasks

Configuring On-Demand Routing

Standards and RFCs

Standard/RFC

Title

IEEE 802.1Q

802.1Q—Virtual LANs

MIBs

MIB

MIBs Link

CISCO-CDP MIB

To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL:

Click Here

Technical Assistance

Description

Link

The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

Click Here

Feature Information for Secure Cisco Discovery Protocol

The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to Click Here . An account on Cisco.com is not required.

Feature Information for Secure Cisco Discovery Protocol

Feature Name

Releases

Feature Information

Secure Cisco Discovery Protocol

The Secure Cisco Discovery Protocol feature allows you to select what information is sent in Cisco Discovery Protocol packets and block sensitive information.

The following commands were introduced or modified: cdp filter-tlv-list, cdp tlv-list, show cdp interface, show cdp tlv-list.