Cisco APIC Layer 2 Networking Configuration Guide, Release 6.2(x)

PDF

Cisco APIC Layer 2 Networking Configuration Guide, Release 6.2(x)

Guidelines and Limitations for Auto Breakout Ports on Fabric Links

Want to summarize with AI?

Log in

Describes the automatic breakout functionality for fabric ports on specific line cards and switches. This information helps users manage transceiver insertion and connectivity requirements for 400G to 100G breakout configurations.


Provides guidelines and limitations for the auto breakout feature on fabric links, including supported hardware, cabling requirements, and operational behaviors in Cisco ACI environments.

The 400G to 100G breakout feature is supported on the fabric ports of the following line card:

  • N9K-X9716D-GX with the QDD-4X100G-FR-S, QDD-4X100G-LR-S, or QDD-400G-SR4.2-BD transceiver

The 400G to 100G breakout feature is supported on the fabric ports of the following switches:

  • N9K-C9348D-GX2A

  • N9K-C9364D-GX2A

  • N9K-C9332D-GX2B

  • N9K-C93600CD-GX

  • N9K-C9316D-GX

  • N9K-C9408 (beginning in the 6.0(2) release)

  • Beginning with the 6.0(2) release, the QDD-400G-SR4.2-BD optic is supported on 400G ports. The peer node with the 100G speed must use QSFP-100G-SR1.2 optics.

  • Beginning with the 6.0(3) release, 400G-to-100G breakout using a QDD-4ZQ100 cable of any length is supported only with the following platforms: N9K-C9332D-GX2B, N9K-C9348D-GX2A, N9K-C9364D-GX2A, N9K-C9316D-GX, and N9K-C93600CD-GX leaf and spine switches, and the N9K-X9716D-GX line card.

  • The N9K-C9400-SW-GX2A switch supports 400G breakout with the N9K-X9400-8D line card expansion module and the peer 100G-PCC is supported with the N9K-X9400-8D and N9K-X9400-16W line card expansion modules.

  • QDD-4X100G-FR-S and QDD-4X100G-LR-S optics are supported on 400G ports. The peer node with the 100G speed can use the following optics: QSFP-100G-DR-S, QSFP-100G-FR-S, or QSFP-100G-LR-S.

Connect the ports with one of the following cables:

  • Cisco QDD-4ZQ100-CU (1M, 2M, 2.5M, and 3M) (beginning in the 6.0(3) release)

  • MPO to 4xLC breakout splitter cable with QDD-4X100G-FR-S or QDD-4X100G-LR-S and 4 x QSFP-100G-DR-S, 4 x QSFP-100G-FR-S, or 4 x QSFP-100G-LR-S on the ends

  • MPO to breakout splitter cable with QDD-400G-SR4.2-BD and 4 x QSFP-100G-SR1.2 on the ends.

Observe the following general guidelines and limitations:

  • Deleting the port profile policy on an already broken out port will clean up the breakout configuration and bring the port back up in the native direction upon switch reload.

  • To change a fabric port with a QDD-400G-SR4.2-BD optic from non-breakout to breakout, you must remove the transceiver, connect the breakout cable to the transceiver, then reinsert the transceiver.

  • GX2 switches support the following switch to switch connectivity: Spine switch-to-leaf switch, Leaf switch-to-spine switch, and Leaf switch-to-leaf switch (multi-tier).

  • GX line cards support spine switch to leaf switch connectivity.

  • Spine switch-to-spine switch breakout is not supported.

  • Spine switch to IPN or ISN breakout is only supported with the Auto Breakout and only with the following 100G and 400G optics.

    • QDD-4X100G-FR-S or QDD-4X100G-LR-S optic on the spine switch and the compatible 100G optics such as QSFP-100G-FR-S and DSFP-100G-LR-S on the IPN or ISN side.

    • QDD-400G-SR4.2-BD optic on the spine switch and the QSFP-100G-SR1.2 optic on the IPN or ISN side.

    • The link does not come up when a QDD-400G-SR4.2-BD optic is on both the sides.

  • In a Cisco ACI environment, the operational requirements for the QDD-400G-SR4.2-BD transceiver vary significantly depending on whether the interface is configured as a Fabric or Access port and the specific nature of the peer device.

  • If you downgrade to a release that does not support breakout for the given hardware and ports, the breakout ports will become not broken out and the links will be down.

  • If you remove an SFP transceiver from a switch, you must wait at least 15 seconds before re-adding the transceiver.

  • With the Cisco Nexus 9300 GX2 series or Cisco N9K-X9716D-GX line cards, ports will not come up if an optic is replaced while the line card is powered off.