Virtual Machine issues
This section includes troubleshooting topics about virtual machine issues.
Administration Virtual Machine on Your Primary or High-Availability System is Down
Your administration virtual machine on your primary or high-availability system is down. You can view your system status by selecting System > View More > Properties. The Administration Site is inaccessible and you see an error message in your browser window (for example, "We've hit a glitch in processing your request.").
There may be a problem with the management of the virtual machine
in VMware vSphere.
Obtain your VMware logs (kb.vmware.com) and provide them to your Cisco TAC
representative. Your representative will use the logs to determine if there is a virtual machine issue on your system. Note that the Tasks and Events messages (virtual machine events from the Tasks and Events tab) are important for troubleshooting purposes.
NIC Teaming Issues
You configured NIC teaming for failover and load balancing and all of your virtual machines seem to be running properly but you begin to encounter problems running the product at maximum load due to meeting failures.
Open your VMware vSphere console and determine if your NIC teaming is working properly on the UCS Servers that are hosting Cisco WebEx Meetings Server virtual machines. This often occurs due to a failed connection from a NIC, forcing another NIC to take on the full network load. This is especially important if your NICs are Gigabit-Ethernet NICS since at maximum port load any one of your NICs would be running to maximum link capacity. So a catastrophic failure on one Gigabit-Ethernet NIC causes the entire networking load to fall on the other NIC, saturating the link and causing application-level issues within Cisco WebEx Meetings Server.
Put Cisco WebEx Meetings Server in maintenance mode, fix or replace the failed NIC, and then restore service to end-users.
Virtual Machine Does Not Boot Up After Deployment
The virtual machine does not boot up after deployment.
The Cisco UCS Server (on which the virtual machine is deployed) does not meet the minimum requirements for the system size.
Check the system requirements for your system size and ensure that there is enough CPU, memory, and free disk space. Refer to the Cisco WebEx Meetings Server System Requirements for more information.
Virtual Machine Fails and Cannot Be Recovered
One of your virtual machines fails and you are unable to fix it even with the assistance of the Cisco TAC.
There are several possible causes including the following: you have a corrupt database, you have a faulty configuration, unsupported maintenance activity, power failures, hardware failures, and more.
If a virtual machine on your high-availability configuration fails, remove the high-availability virtual machine from your system. Redeploy all of your high-availability virtual machines and then reconfigure the system for high availability. Refer to "Configuring a High Availability System" in the Cisco WebEx Meetings Server Administration Guide for more information. Similarly if an Internet Reverse Proxy virtual machine fails, you must remove that virtual machine from your system. Then redeploy and reconfigure your Internet Reverse Proxy virtual machine. Refer to "Adding Public Access" in the Cisco WebEx Meetings Server Administration Guide for more information. For any other virtual machine, your must rebuild your system using the Disaster Recovery feature. Refer to "Using the Disaster Recovery Feature" in the Cisco WebEx Meetings Server Administration Guide for more information.
Virtual Machine Issues and Crashes
Your virtual machine crashes and does not resume functioning.
Attempt to perform the following solutions:
Attempt to restart your virtual machine from VMware vCenter.
- If you took snapshots of your virtual machines, attempt to restore a snapshot.
Snapshots might not contain all of your configuration information and you might have to perform some configuration tasks to restore all functions on your system.
If you configured a storage server, you can attempt to perform a disaster recovery procedure to restore your system. Refer to "Using the Disaster Recovery Feature" in your Administration Guide for more information.
If none of the above solve your problem, contact the Cisco TAC for assistance. You can contact the TAC at the following URL: http://www.cisco.com/cisco/web/support/index.html
Virtual Machine Is
Unreachable Due to a Hardware Failure
The primary virtual machine is
unreachable. Users cannot access the Administration site and cannot access the
WebEx site to start or schedule meetings. Administrators cannot make a SSH
connection to the virtual machine. Fail over to the High Availability system
does not occur.
The disk hosting the primary Admin
virtual machine is inaccessible.
Using VMware vCenter, shut down the
inaccessible virtual machine. By doing this, the failover process to the HA
system completes successfully. When the hardware problem is resolved, contact
Cisco TAC for assistance in restoring your primary virtual machine.
Virtual Machine Repeatedly Reboots
The virtual machine on which I have deployed the Cisco WebEx Meetings Server OVA, repeatedly reboots.
NTP is not configured on the ESXi host.
Configure NTP on your ESXi host, check the DNS on your ESXi host to make sure it is resolving the NTP server correctly, and then redeploy the OVA to the virtual machine.